Additively manufactured Ti-6Al-4V thin struts via laser powder bed fusion: Effect of building orientation on geometrical accuracy and mechanical properties.

Porous metal lattice structures have a very high potential in biomedical applications, setting as innovative new generation prosthetic devices. Laser powder bed fusion (L-PBF) is one of the most widely used additive manufacturing (AM) techniques involved in the production of Ti6Al4V lattice structures. The mechanical and failure behavior of lattice structures is strongly affected by geometrical imperfections and defects occurring during L-PBF process. Due to the influence of multiple process parameters and to their combined effect, the mechanical properties of these structures are not yet properly understood. Despite the major commitment to characterize and better comprehend lattice structures, little attention has been paid to the impact that single struts have on the overall lattice properties. In this work, the authors have investigated the tensile strength and fatigue behavior of thin L-PBF Ti6Al4V lattice struts at different building orientations (0°, 15°, 45°, and 90°). This investigation has been focused on the effect that microstructural defects (particularly porosity) and actual surface geometry (including surface texture and geometrical errors such as varying cross-section shape and size) have on the mechanical performances of the struts in relation to their building direction. The results have shown that there is a tendency, particularly for low printing angles, of fatigue life to decrease with decreasing of the building angle. This is mainly due to the surge in surface texture and loss in cross-sectional regularity. On the other hand, the monotonic tensile test results have shown a low sensitivity to these factors. The strut failure behavior has been examined employing dynamic digital image correlation (DIC) of tensile tests and scanning electron imaging (SEM) of the fracture surfaces.

Alumina-on-alumina hip implants: A wear study of retrieved components.

Alumina-alumina bearings are among the most resistant to wear in total hip replacement. Examination of their surfaces is one way of comparing damage caused by wear of hip joints simulated in vitro to that seen in explanted bearings. The aim of this study was to determine whether second-generation ceramic bearings exhibited a better pattern of wear than those reported in the literature for first-generation bearings. We considered both macro- and microscopic findings. We found that long-term alumina wear in association with a loose acetabular component could be categorised into three groups. Of 20 specimens, four had 'low wear', eight 'crescent wear' and eight 'severe wear', which was characterised by a change in the physical shape of the bearing and a loss of volume. This suggests that the wear in alumina-alumina bearings in association with a loose acetabular component may be variable in pattern, and may explain, in part, why the wear of a ceramic head in vivo may be greater than that seen after in vitro testing.

Integrated friction measurements in hip wear simulations: short-term results.

Hip joint wear simulators are used extensively to simulate the dynamic behaviour of the human hip joint and, through the wear rate, gain a concrete indicator about the overall wear performance of different coupled bearings. Present knowledge of the dynamic behaviour of important concurrent indicators, such as the coefficient of friction, could prove helpful for the continuing improvement in applied biomaterials. A limited number of commercial or custom-made simulators have been designed specifically for friction studies but always separately from wear tests; thus, analysis of these two important parameters has remained unconnected. As a result, a new friction sensor has been designed, built, and integrated in a commercial biaxial rocking motion hip simulator. The aim of this study is to verify the feasibility of an experimental set-up in which the dynamic measurement of the friction factor could effectively be implemented in a standard wear test without compromising its general accuracy and repeatability. A short wear test was run with the new set-up for 1 x 10(6) cycles. In particular, three soft-bearings (metal-on-polyethylene, phi = 28 mm) were tested; during the whole test, axial load and frictional torque about the vertical loading axis were synchronously recorded in order to calculate the friction factor. Additional analyses were performed on the specimens, before and after the test, in order to verify the accuracy of the wear test. The average friction factor was 0.110 +/- 0.025. The friction sensors showed good accuracy and repeatability throughout. This innovative set-up was able to reproduce stable and reliable measurements. The results obtained encourage further investigations of this set-up for long-term assessment and using different combinations of materials.

Unicompartmental knee prostheses: in vitro wear assessment of the menisci tibial insert after two different fixation methods.

Knee osteoarthritis is a complex clinical scenario where many biological and mechanical factors influence the severity of articular degenerative changes. Minimally invasive knee prosthetic surgery, with only a compartment replacement (unicompartmental knee replacement), might be a good compromise between osteotomy and total knee prosthesis. The focus of this study was to develop and validate a protocol to assess the fixation method of the femoral components in mechanical simulation, for pre-clinical validation; the wear behaviour of two different fixation frames was quantified and compared. In particular, two different wear tests were conducted using the same knee simulator, the same load profiles and the same kinematics; two different fixation methods were applied to the femoral sleds (synthetic femur and metal block). Surface characterization on both articulating bearings was performed by a roughness measuring machine and coordinate measuring machine. The wear produced by the tibial inserts using the synthetic femur was considerably higher than the wear registered by the metal-block holder. Roughness measurements on femoral sleds showed a limited number of scratches with high R(t) values for the metal-block set-up; the damaged surface broadened in the case of femoral condyles and tibial inserts mounted on composite bone, but lower R(t) and linear penetration values were measured. The two holding frames showed different wear activities as a consequence of dissimilar dynamic performance. Further observations should be made in vivo to prove the actual importance of synthetic bone simulations and specific material behaviour.