Gigabit per second visible light communication based on AlGaInP red micro-LED micro-transfer printed onto diamond and glass.

Full-color smart displays, which act both as a display and as a high-speed visible light communication (VLC) transmitter, can be realized by the integration of red-green-blue micron-sized light emitting diodes (micro-LEDs) onto a common platform. In this work, we report on the integration of aluminum gallium indium phosphide red micro-LEDs onto diamond and glass substrates by micro-transfer printing and their application in VLC. The device on-diamond exhibits high current density and bandwidth operation, enabled by diamond's superior thermal properties. Employing an orthogonal frequency division multiplexing modulation scheme, error-free data rates of 2.6 Gbps and 5 Gbps are demonstrated for a single micro-LED printed on-glass and on-diamond, respectively. In a parallel configuration, a 2x1 micro-LED array achieves error-free data rates of 3 Gbps and 6.6 Gbps, on-glass and on-diamond, respectively.

Direct integration of micro-LEDs and a SPAD detector on a silicon CMOS chip for data communications and time-of-flight ranging.

We present integration of singulated micron-sized light emitting diodes (micro-LEDs) directly onto a silicon CMOS drive chip using a transfer printing method. An 8x8 micro-LED device array with individual control over each pixel is demonstrated with modulation bandwidths up to 50 MHz, limited by the large modulation depth of the driver chip. The 2 kHz frame rate CMOS driver also incorporates a Single Photon Avalanche Diode device thus allowing detection and transmission functionality on a single integrated chip. Visible light communications at data rates up to 1 Mbps, and time-of-flight ranging with cm-scale resolution are demonstrated using this hybrid integrated system.

On-chip GaN-based dual-color micro-LED arrays and their application in visible light communication.

Integrated multi-color micron-sized light emitting diode (micro-LED) arrays have been demonstrated in recent years for display applications; however, their potential as visible light communication (VLC) transmitters is yet to be fully explored. In this work, we report on the fabrication and characterization of on-chip dual-color micro-LED arrays and their application in VLC. For this purpose, blue-green and blue-violet micro-LED arrays were fabricated by transfer printing blue-emitting micro-LEDs onto the substrate of green and violet micro-LEDs, respectively. The potential of these dual-color micro-LED arrays as VLC transmitters is demonstrated with respective error-free data rates of 1.79 and 3.35 Gbps, achieved by the blue-green and blue-violet devices in a dual wavelength multiplexing scheme.

Hybridization of Zinc Oxide Tetrapods for Selective Gas Sensing Applications.

In this work, the exceptionally improved sensing capability of highly porous three-dimensional (3-D) hybrid ceramic networks toward reducing gases is demonstrated for the first time. The 3-D hybrid ceramic networks are based on doped metal oxides (MexOy and ZnxMe1-xOy, Me = Fe, Cu, Al) and alloyed zinc oxide tetrapods (ZnO-T) forming numerous junctions and heterojunctions. A change in morphology of the samples and formation of different complex microstructures is achieved by mixing the metallic (Fe, Cu, Al) microparticles with ZnO-T grown by the flame transport synthesis (FTS) in different weight ratios (ZnO-T:Me, e.g., 20:1) followed by subsequent thermal annealing in air. The gas sensing studies reveal the possibility to control and change/tune the selectivity of the materials, depending on the elemental content ratio and the type of added metal oxide in the 3-D ZnO-T hybrid networks. While pristine ZnO-T networks showed a good response to H2 gas, a change/tune in selectivity to ethanol vapor with a decrease in optimal operating temperature was observed in the networks hybridized with Fe-oxide and Cu-oxide. In the case of hybridization with ZnAl2O4, an improvement of H2 gas response (to ∼7.5) was reached at lower doping concentrations (20:1), whereas the increase in concentration of ZnAl2O4 (ZnO-T:Al, 10:1), the selectivity changes to methane CH4 gas (response is about 28). Selectivity tuning to different gases is attributed to the catalytic properties of the metal oxides after hybridization, while the gas sensitivity improvement is mainly associated with additional modulation of the electrical resistance by the built-in potential barriers between n-n and n-p heterojunctions, during adsorption and desorption of gaseous species. Density functional theory based calculations provided the mechanistic insights into the interactions between different hybrid networks and gas molecules to support the experimentally observed results. The studied networked materials and sensor structures performances would provide particular advantages in the field of fundamental research, applied physics studies, and industrial and ecological applications.

Spectroscopic analysis of LYSO:Ce crystals.

Rare earth orthosilicates are among the most widely used scintillator materials in the last decades. Particularly, lutetium-yttrium oxyorthosilicate (LYSO) is known to exhibit great potentialities in the field of radiation detectors for medical imaging. Consequently, an in-depth knowledge of the material properties is of utmost interest for the mentioned applications. In this work the spectroscopic properties of commercial cerium doped lutetium-yttrium oxyorthosilicate crystals (LYSO:Ce) were investigated by Raman spectroscopy, steady state photoluminescence, photoluminescence excitation and time resolved photoluminescence. Site selective excitation was used under steady state (325nm) and pulsed (266nm) conditions to separately investigate the temperature dependence of the 5d→4f Ce1 and Ce2 luminescence, allowing to establish the thermal quenching dependence of the Ce2 optical center. In the case of the Ce1 optical center, a luminescence quantum efficiency of 78% was obtained from 14K to room temperature with 266nm photon excitation.