Effect of the Synthetic Parameters over ZnO in the CO2 Photoreduction.

Zinc oxide (ZnO) is an attractive semiconductor material for photocatalytic applications, owing to its opto-electronic properties. Its performances are, however, strongly affected by the surface and opto-electronic properties (i.e., surface composition, facets and defects), in turn related to the synthesis conditions. The knowledge on how these properties can be tuned and how they are reflected on the photocatalytic performances (activity and stability) is thus essential to achieve an active and stable material. In this work, we studied how the annealing temperature (400 °C vs. 600 °C) and the addition of a promoter (titanium dioxide, TiO2) can affect the physico-chemical properties of ZnO materials, in particular surface and opto-electronic ones, prepared through a wet-chemistry method. Then, we explored the application of ZnO as a photocatalyst in CO2 photoreduction, an appealing light-to-fuel conversion process, with the aim to understand how the above-mentioned properties can affect the photocatalytic activity and selectivity. We eventually assessed the capability of ZnO to act as both photocatalyst and CO2 adsorber, thus allowing the exploitation of diluted CO2 sources as a carbon source.

Biostimulants derived from organic urban wastes and biomasses: An innovative approach.

We used humic and fulvic acids extracted from digestate to formulate nanohybrids with potential applications in agronomy. In order to obtain a synergic co-release of plant-beneficial agents, we functionalized with humic substances two inorganic matrixes: hydroxyapatite (Ca10(PO4)6(OH)2, HP) and silica (SiO2) nanoparticles (NPs). The former is a potential controlled-release fertilizer of P, and the latter has a beneficial effect on soil and plants. SiO2 NPs are obtained from rice husks by a reproducible and fast procedure, but their ability to absorb humic substances is very limited. HP NPs coated with fulvic acid are instead a very promising candidate, based on desorption and dilution studies. The different dissolutions observed for HP NPs coated with fulvic and humic acids could be related to the different interaction mechanisms, as suggested by the FT-IR study.

Efficient Day-and-Night NO2 Abatement by Polyaniline/TiO2 Nanocomposites.

Finding innovative and highly performing approaches for NOx degradation represents a key challenge to enhance the air quality of our environment. In this study, the high efficiency of PANI/TiO2 nanostructures in the NO2 abatement both in the dark and under light irradiation is demonstrated for the first time. Heterostructures were synthesized by a "green" method and their composition, structure, morphology and oxidation state were investigated by a combination of characterization techniques. The results show that the unique PANI structure promotes two mechanisms for the NO2 abatement in the dark (adsorption on the polymeric chains and chemical reduction to NO), whereas the photocatalytic behavior prevails under light irradiation, leading to the complete NOx degradation. The best-performing materials were subjected to recycling tests, thereby showing high stability without any significant activity loss. Overall, the presented material can represent an innovative and efficient night-and-day solution for NOx abatement.

Parent, child, and environmental predictors of vegetable consumption in Italian, Polish, and British preschoolers.

This study compared the vegetable intake of preschool children from three European countries [Italy, Poland, and the United Kingdom (UK)] and explored the parent, child, and environmental factors that predicted intake in each country. A total of 408 parents of preschoolers (Italy: N = 61, Poland: N = 124, and UK: N = 225; child mean age = 32.2 months, SD = 9.47) completed an online survey comprising a set of standardised questionnaires. For all three countries, the questionnaires included measures of children's vegetable intake (VegFFQ), child eating behaviour (CEBQ-FF), parents' mealtime goals (FMGs), and sociodemographic questions about family background and environment. In the UK and Italy, additional questionnaires were used to assess child temperament (EAS-T) and parents' feeding practices (CFPQ). The results showed that the number of child-sized portions of vegetables consumed per day varied significantly across countries; Polish children consumed the most (∼3 portions) and Italian children the least (∼1.5 portions). Between-country differences were seen in parents' goals for family mealtimes; compared to Italian parents, Polish and UK parents were more motivated to minimise mealtime stress, increase family involvement in meal preparation, and share the same foods with family members. British and Italian parents also adopted different feeding practices; parents in the UK reported more use of healthy modelling behaviours and more use of foods to support their child's emotion regulation. In terms of child factors, Italian children were reported to be more emotional and more sociable than British children. Analyses of the relationships between the parent, child, and environmental factors and children's vegetable intake revealed both similarities and differences between countries. Negative predictors of vegetable intake included child food fussiness in the UK and Poland, child temperament (especially, shyness) in Italy, and the use of food as a reward and child emotionality in the UK. Positive predictors included the parental mealtime goal of 'family involvement' in the UK. These results highlight differences in the extent to which European preschoolers achieve recommended levels of vegetable intake, and in the factors that influence whether they do. The results suggest a need to develop healthy eating interventions that are adopted to meet the specific needs of the countries in which they are implemented.

Corrigendum: See & Eat! Using E-books to Promote Vegetable Eating Among Preschoolers: Findings From an Italian Sample.

[This corrects the article DOI: 10.3389/fpsyg.2021.712416.].

Solar Light Photoactive Floating Polyaniline/TiO2 Composites for Water Remediation.

In the present study, the development of innovative polyurethane-polyaniline/TiO2 modified floating materials applied in the sorption and photodegradation of rhodamine B from water matrix under solar light irradiation is reported. All the materials were fabricated with inexpensive and easy approaches and were properly characterized. The effect of the kind of polyaniline (PANI) dopant on the materials' behavior was investigated, as well as the role of the conducting polymer in the pollutant abatement on the basis of its physico-chemical characteristics. Rhodamine B is removed by adsorption and/or photodegradation processes depending on the type of doping agent used for PANI protonation. The best materials were subjected to recycle tests in order to demonstrate their stability under the reaction conditions. The main transformation products formed during the photodegradation process were identified by ultraperformance liquid chromatography-mass spectrometry (UPLC/MS). The results demonstrated that photoactive floating PANI/TiO2 composites are useful alternatives to common powder photocatalysts for the degradation of cationic dyes.

See & Eat! Using E-books to Promote Vegetable Eating Among Preschoolers: Findings From an Italian Sample.

Different strategies have been developed to help parents with introducing new or disliked vegetables. Nonetheless, many parents of preschoolers struggle against children's refusal to eat vegetables. In this study, we aimed to evaluate the effectiveness of e-books in promoting positive attitudes toward vegetables through repeated visual exposures. A total of 61 families with preschoolers joined the See & Eat study and received an e-book about one of two vegetables chosen from a list of 24. Parents provided ratings of children's willingness to taste, intake, and liking of the chosen vegetables before and after reading the e-book; parents also evaluated their children's food fussiness and their agreement with respect to three mealtime goals of the family. Using a 2 (vegetable: target or non-target) × 2 (time: pre-test or post-test) within-subjects analysis, results from 53 families revealed a significant increase in children's willingness to taste, intake, and liking at post-test of both target and non-target vegetables. Following a two-week parent-child e-book reading intervention, children's food fussiness and parents' endorsement of positive mealtime goals slightly but significantly increased. Results suggest that e-books are effective in encouraging healthy eating among preschoolers and that the positive effect of e-book reading can generalize to other vegetables.

Oxidative Inactivation of SARS-CoV-2 on Photoactive AgNPs@TiO2 Ceramic Tiles.

The current SARS-CoV-2 pandemic causes serious public health, social, and economic issues all over the globe. Surface transmission has been claimed as a possible SARS-CoV-2 infection route, especially in heavy contaminated environmental surfaces, including hospitals and crowded public places. Herein, we studied the deactivation of SARS-CoV-2 on photoactive AgNPs@TiO2 coated on industrial ceramic tiles under dark, UVA, and LED light irradiations. SARS-CoV-2 inactivation is effective under any light/dark conditions. The presence of AgNPs has an important key to limit the survival of SARS-CoV-2 in the dark; moreover, there is a synergistic action when TiO2 is decorated with Ag to enhance the virus photocatalytic inactivation even under LED. The radical oxidation was confirmed as the the central mechanism behind SARS-CoV-2 damage/inactivation by ESR analysis under LED light. Therefore, photoactive AgNPs@TiO2 ceramic tiles could be exploited to fight surface infections, especially during viral severe pandemics.

Piezo-enhanced photocatalytic diclofenac mineralization over ZnO.

The degradation of diclofenac has been realized for the first time by a piezo-enhanced sonophotocatalytic approach based on ZnO. The sonophotocatalytic degradation showed a slight enhancement in the degradation of the parent compound, whereas strong synergistic effects were observed for the mineralization process when suitable ZnO morphologies are used, reaching 70% of complete degradation of 25 ppm diclofenac using 0.1 g/L ZnO in 360 min. Tests in a complex water matrix show enhanced diclofenac removal, outperforming a TiO2 benchmark photocatalyst. These promising experimental results promote this process as a good alternative to traditional degradation approaches for remediation of real water matrices.

TiO2-Chitosan Hybrid Materials for Drug Delivery Applications: Conjugation Reaction with a Model Drug and Evaluation of the Functional Properties.

The combination of TiO2 and chitosan is known to allow the achievement of implantable devices which combines the mechanical properties of TiO2, with the presence of chitosan, which ensures antibacterial properties combined with an in-situ drug-delivery of biomolecules physisorbed and/or covalently linked to chitosan. In this study, 5-aminofluorescein (5-AF), a derivative of fluorescein containing a primary amino group, has been used as model molecule to simulate a drug. This dye is characterized by low cost and low toxicity, and due to its high molar absorptivity it can easily be detected by means of absorption and emission spectroscopies. The combination of 5-AF and maleic anhydride (MA) with TiO2-chitosan materials has generated a range of novel hybrid materials tailored to applications in localized stimuli-responsive drug delivery systems. Maleic anhydride has been used as pH sensitive spacer for the covalent functionalization of the TiO2-chitosan hybrid with MA as linker molecule. This functionalization allowed to obtain a pH-sensitive hybrid material. The efficiency of the functionalization has been verified by means of different physico-chemical characterization techniques. The behaviour of the functionalized materials is related to different parameters, among which the ratio between physisorbed/coordinated and chemisorbed 5-AF and the matrix degradation. Moreover, delivery tests in simulated body solutions at different pH have been performed showing a pH-sensitive drug delivery behaviour and indicating that the release of 5-AF is favoured at basic pH.

Morphology, Surface Structure and Water Adsorption Properties of TiO2 Nanoparticles: A Comparison of Different Commercial Samples.

Water is a molecule always present in the reaction environment in photocatalytic and biomedical applications of TiO2 and a better understanding of its interaction with the surface of TiO2 nanoparticles is crucial to develop materials with improved performance. In this contribution, we first studied the nature and the surface structure of the exposed facets of three commercial TiO2 samples (i.e., TiO2 P25, SX001, and PC105) by electron microscopy and IR spectroscopy of adsorbed CO. The morphological information was then correlated with the water adsorption properties, investigated at the molecular level, moving from multilayers of adsorbed H2O to the monolayer, combining medium- and near-IR spectroscopies. Finally, we assessed in a quantitative way the surface hydration state at different water equilibrium pressures by microgravimetric measurements.

ORR in Non-Aqueous Solvent for Li-Air Batteries: The Influence of Doped MnO2-Nanoelectrocatalyst.

One of the major drawbacks in Lithium-air batteries is the sluggish kinetics of the oxygen reduction reaction (ORR). In this context, better performances can be achieved by adopting a suitable electrocatalyst, such as MnO2. Herein, we tried to design nano-MnO2 tuning the final ORR electroactivity by tailoring the doping agent (Co or Fe) and its content (2% or 5% molar ratios). Staircase-linear sweep voltammetries (S-LSV) were performed to investigate the nanopowders electrocatalytic behavior in organic solvent (propylene carbonate, PC and 0.15 M LiNO3 as electrolyte). Two percent Co-doped MnO2 revealed to be the best-performing sample in terms of ORR onset shift (of ~130 mV with respect to bare glassy carbon electrode), due to its great lattice defectivity and presence of the highly electroactive γ polymorph (by X-ray diffraction analyses, XRPD and infrared spectroscopy, FTIR). 5% Co together with 2% Fe could also be promising, since they exhibited fewer diffusive limitations, mainly due to their peculiar pore distribution (by Brunauer-Emmett-Teller, BET) that disfavored the cathode clogging. Particularly, a too-high Fe content led to iron segregation (by energy dispersive X-ray spectroscopy, EDX, X-ray photoelectron spectroscopy, XPS and FTIR) provoking a decrease of the electroactive sites, with negative consequences for the ORR.

Role of Synthetic Parameters on the Structural and Optical Properties of N,Sn-Copromoted Nanostructured TiO2: A Combined Ti K-Edge and Sn L2,3-Edges X-ray Absorption Investigation.

Sn-modification of TiO2 photocatalysts has been recently proposed as a suitable strategy to improve pollutant degradation as well as hydrogen production. In particular, visible light activity could be promoted by doping with Sn2+ species, which are, however, thermally unstable. Co-promotion with N and Sn has been shown to lead to synergistic effects in terms of visible light activity, but the underlying mechanism has, so far, been poorly understood due to the system complexity. Here, the structural, optical, and electronic properties of N,Sn-copromoted, nanostructured TiO2 from sol-gel synthesis were investigated: the Sn/Ti molar content was varied in the 0-20% range and different post-treatments (calcination and low temperature hydrothermal treatment) were adopted in order to promote the sample crystallinity. Depending on the adopted post-treatment, the optical properties present notable differences, which supports a combined role of Sn dopants and N-induced defects in visible light absorption. X-ray absorption spectroscopy at the Ti K-edge and Sn L2,3-edges shed light onto the electronic properties and structure of both Ti and Sn species, evidencing a marked difference at the Sn L2,3-edges between the samples with 20% and 5% Sn/Ti ratio, showing, in the latter case, the presence of tin in a partially reduced state.

Exploring SnxTi1-xO2 Solid Solutions Grown onto Graphene Oxide (GO) as Selective Toluene Gas Sensors.

The major drawback of oxide-based sensors is the lack of selectivity. In this context, SnxTi1-xO2/graphene oxide (GO)-based materials were synthesized via a simple hydrothermal route, varying the titanium content in the tin dioxide matrix. Then, toluene and acetone gas sensing performances of the as-prepared sensors were systematically investigated. Specifically, by using 32:1 SnO2/GO and 32:1 TiO2/GO, a greater selectivity towards acetone analyte, also at room temperature, was obtained even at ppb level. However, solid solutions possessing a higher content of tin relative to titanium (as 32:1 Sn0.55Ti0.45O2/GO) exhibited higher selectivity towards bigger and non-polar molecules (such as toluene) at 350 °C, rather than acetone. A deep experimental investigation of structural (XRPD and Raman), morphological (SEM, TEM, BET surface area and pores volume) and surface (XPS analyses) properties allowed us to give a feasible explanation of the different selectivity. Moreover, by exploiting the UV light, the lowest operating temperature to obtain a significant and reliable signal was 250 °C, keeping the greater selectivity to the toluene analyte. Hence, the feasibility of tuning the chemical selectivity by engineering the relative amount of SnO2 and TiO2 is a promising feature that may guide the future development of miniaturized chemoresistors.

Understanding Solid-Gas Reaction Mechanisms by Operando Soft X-Ray Absorption Spectroscopy at Ambient Pressure.

Ambient-pressure operando soft X-ray absorption spectroscopy (soft-XAS) was applied to study the reactivity of hydroxylated SnO2 nanoparticles toward reducing gases. H2 was first used as a test case, showing that the gas phase and surface states can be simultaneously probed: Soft-XAS at the O K-edge gains sensitivity toward the gas phase, while at the Sn M4,5-edges, tin surface states are explicitly probed. Results obtained by flowing hydrocarbons (CH4 and CH3CHCH2) unequivocally show that these gases react with surface hydroxyl groups to produce water without producing carbon oxides and release electrons that localize on Sn to eventually form SnO. The partially reduced SnO2 - x layer at the surface of SnO2 is readily reoxidized to SnO2 by treating the sample with O2 at mild temperatures (>200 °C), revealing the nature of "electron sponge" of tin oxide. The experiments, combined with DFT calculations, allowed devising of a mechanism for dissociative hydrocarbon adsorption on SnO2, involving direct reduction of Sn sites at the surface via cleavage of C-H bonds and the formation of methoxy- and/or methyl-tin species at the surface.

Photocatalytic porcelain grés large slabs digitally coated with AgNPs-TiO2.

TiO2 is employed as both photocatalytic and structural materials, leading to its applications in external coatings or in interior furnishing devices, including cement mortar, tiles, floorings, and glass supports. The authors have already demonstrated the efficiency of photoactive micro-sized TiO2 and here its industrial use is reported using the digital printing to coat porcelain grés slabs. Many advantages are immediately evident, namely rapid and precise deposition, no waste of raw materials, thus positively affecting the economy of the process. Data for the thin films deposited by digital printing were compared with those obtained for the conventional spray method. The use of metal-doped TiO2 is also reported so that the photoactivity of these materials can be exploited even under LED light. The digital inkjet printed coatings exhibited superior photocatalytic performance owing to both higher exposed surface area and greater volume of deposited anatase, as well as the greater areal distribution density of thinly and thickly coated regions. Moreover, the presence of TiO2 doped silver increased the efficiency of the materials in NOx degradation both under UVA and LED lights.

Nano-MnO2 Decoration of TiO2 Microparticles to Promote Gaseous Ethanol Visible Photoremoval.

TiO2-based photocatalysis under visible light is an attractive way to abate air pollutants. Moreover, developing photocatalytic materials on a large-scale requires safe and low-cost precursors. Both high-performance TiO2 nanopowders and visible-light active noble metals do not match these requirements. Here, we report the design of novel Mn-decorated micrometric TiO2 particles. Pigmentary TiO2 replaced unsafe nano-TiO2 and firmly supported MnOx particles. Mn replaced noble metals such as Au or Ag, opening the way for the development of lower cost catalysts. Varying Mn loading or pH during the impregnation affected the final activity, thus giving important information to optimize the synthesis. Photocatalytic activity screening occurred on the gas-phase degradation of ethanol as a reference molecule, both under ultraviolet (UV) (6 h) and Light Emitting Diode (LED) (24 h) irradiation. Mn-doped TiO2 reached a maximum ethanol degradation of 35% under visible light after 24 h for the sample containing 20% of Mn. Also, we found that an acidic pH increased both ethanol degradation and mineralization to CO2, while an alkaline pH drastically slowed down the reaction. A strict correlation between photocatalytic results and physico-chemical characterizations of the synthesized powders were drawn.

Micro-sized TiO2 as photoactive catalyst coated on industrial porcelain grès tiles to photodegrade drugs in water.

Pharmaceutical compounds and their metabolites raise worrying questions because of their continuous release and lack of efficient removal by conventional wastewater treatments; therefore, they are being detected in groundwater, surface water and drinking water in increasing concentrations. Paracetamol and aspirin are two of the most commonly used drugs employed as fever reducer, analgesic and anti-inflammatory. They and their metabolites are very often found in river water, so their degradation is necessary in order to render water suitable for human consumption. The present work is focused on the comparison of the photocatalytic performance of industrial active grés porcelain tiles covered with a commercial micro-sized TiO2 by industrial process using either conventional spray deposition or innovative digital printing methods. The photodegradation of two commonly used drugs, namely aspirin and paracetamol, was investigated both individually and as a mixture, in both deionized and tap water. The results reveal the full conversion of the drugs and the significant role of the photocatalytic tiles in the mineralization processes leading to harmless inorganic species. In particular, the digitally printed tiles exhibited better photodegradation performance for both drugs compared to the spray deposited tiles. No deactivation was observed on both photocatalytic tiles.

Aspirin and paracetamol removal using a commercial micro-sized TiO2 catalyst in deionized and tap water.

Micro-sized TiO2 catalyst was employed to degrade pharmaceutical compounds, i.e. aspirin and paracetamol, two of the most widely used drugs, purchasable without prescription. Their active agents, acetylsalicylic acid and acetaminophen, are characterized by different substituent groups, linked to the aromatic ring, which affect both the photodegradation and mineralization processes. The experimental conditions highlight the relationship between the nature of the pristine molecules, their degradation mechanisms, their mutual interference and the water's role. The research started from model systems with a single pollutant to the mixture of them and finally by moving from deionized water to tap water.

Copper NPs decorated titania: A novel synthesis by high energy US with a study of the photocatalytic activity under visible light.

The most important drawback of the use of TiO2 as photocatalyst is its lack of activity under visible light. To overcome this problem, the surface modification of commercial micro-sized TiO2 by means of high-energy ultrasound (US), employing CuCl2 as precursor molecule to obtain both metallic copper as well as copper oxides species at the TiO2 surface, is here. We have prepared samples with different copper content, in order to evaluate its impact on the photocatalytic performances of the semiconductor, and studied in particular the photodegradation in the gas phase of some volatile organic molecules (VOCs), namely acetone and acetaldehyde. We used a LED lamp in order to have only the contribution of the visible wavelengths to the TiO2 activation (typical LED lights have no emission in the UV region). We employed several techniques (i.e., HR-TEM, XRD, FT-IR and UV-Vis) in order to characterize the prepared samples, thus evidencing different sample morphologies as a function of the various copper content, with a coherent correlation between them and the photocatalytic results. Firstly, we demonstrated the possibility to use US to modify the TiO2, even when it is commercial and micro-sized as well; secondly, by avoiding completely the UV irradiation, we confirmed that pure TiO2 is not activated by visible light. On the other hand, we showed that copper metal and metal oxides nanoparticles strongly and positively affect its photocatalytic activity.