Treating High COD Dyeing Wastewater via a Regenerative Sorption-Oxidation Process Using a Nano-Pored Activated Carbon.

Nowadays, the structural complexity of dyes used in the textile industry and the widely adopted water-saving strategy in the dyeing processes often fail plants' biological wastewater treatment units due to chemical oxygen demand (COD) overload. To alleviate this problems, this study investigated a regenerable adsorption-oxidation process to treat dyeing wastewater with COD around 10,000 mg/dm3 using a highly nano-pored activated carbon (AC) as a COD adsorbent, followed by its regeneration using hydrogen peroxide as an oxidizing reagent. In addition to studying AC's COD adsorption and oxidation performance, its operational treatment conditions in terms of temperature and pH were assessed. The results firstly demonstrated that about 50-60% of the COD was consistently adsorbed during the repeated adsorption operation before reaching AC's maximum adsorption capacity (qmax) of 0.165 g-COD/g-AC. The optimal pH and temperature during adsorption were 4.7 and 25 °C, respectively. Secondly, AC regeneration was accomplished by using an initial peroxide concentration of 2.5% (by wt %) and EDTA-Fe of 2.12 mmole/dm3. The reuse of the regenerated ACs was doable. Surprisingly, after the first AC regeneration, the COD adsorption capacity of the regenerated AC even increased by ~7% with respect to the virgin AC. Thirdly, the results of a five-consecutive adsorption-regeneration operation showed that a total of 0.3625 g COD was removed by the 5 g AC used, which was equivalent to an adsorption capacity (q) of 0.0725 (= 0.3625/5) g-COD/g-AC during each adsorption stage. Based on the obtained results, a regenerable COD adsorption-oxidation process using a nano-pored AC to treat the high-textile-COD wastewater looks promising. Thus, a conceptual treatment unit was proposed, and its potential benefits and limitations were addressed.

A Pest or Otherwise? Encounter of Oryctes rhinoceros (Coleoptera: Scarabaeidae) with Persistent Organic Pollutants.

The potential use of invertebrates as bioreactors to treat environmental pollutants is promising and of great interest. Three types of the persistent organic pollutants (POPs), namely pentachlorophenol (PCP), PAHs (naphthalene and phenanthrene) and dieldrin (DLN), were spiked in soil and treated by using Oryctes rhinoceros larvae, a known pest of coconut trees in southeast Asia, and also the indicators of POP toxicity and the fate and degradability of the ingested POPs were assessed. The larvae were tested at various levels of the POPs and went through an acclimation process. Without acclimation, the tolerance limits of the larvae toward PCP, PAHs and DLN were 200, 100 and 0.1 mg/kg-soil, respectively, yet with acclimation, the tolerance levels increased to 800, 400 and 0.5 mg/kg-soil, respectively. Biodegradation rates of all the tested POPs were >90% by week 2, with <5% and nearly 0% remaining in the feces and body of the larvae, respectively. The results suggest that the use of the beetle larvae in soil POP decontamination is doable.

Hybrid ZnO/chitosan antimicrobial coatings with enhanced mechanical and bioactive properties for titanium implants.

A biocomposite coating comprising chitosan and ZnO deposited on a porous Ti oxide is developed to avoid orthopedic and dental implant-related infections. The coating comprised of an inner layer of nanoporous TiO2 and the outer layer of the chitosan matrix with ZnO nanoparticles. Microbiological tests show that chitosan coating is effective against Escherichia coli (E. coli), however, its ability to inhibit bacterial adhesion is very limited. A 1.2-fold increase in the antibacterial activity of chitosan/ZnO coating against E. coli was detected as compared to the chitosan coating alone, and the chitosan/ZnO efficiently inhibited biofilm formation. In addition, the chitosan/ZnO coating exhibited improved bioactivity compared to the chitosan coating. The improvement in antibacterial properties and bioactivity of the chitosan/ZnO coating is attributed to the release of Zn2+ ions. The critical force of scratching the chitosan/ZnO coating was approximately twice that of the chitosan coating. The potentiodynamic polarization results confirmed that the corrosion resistance of the implant with ZnO/chitosan/Ti structure was improved. In addition, cytocompatibility evaluation indicated that the chitosan/ZnO coating has good cytocompatibility in MG-63 cells as compared to pure Ti.

Polyethylene Glycol6000/carbon Nanodots as Fluorescent Bioimaging Agents.

Photoluminescent nanomaterials have immense potential for use in biological systems due to their excellent fluorescent properties and small size. Traditional semiconductor quantum dots are heavy-metal-based and can be highly toxic to living organisms, besides their poor photostability and low biocompatibility. Nano-sized carbon quantum dots and their surface-modified counterparts have shown improved characteristics for imaging purposes. We used 1,3, 6-trinitropyrene (TNP) and polyethylene glycol6000 (PEG6000) in a hydrothermal method to prepare functional polyethylene glycol6000/carbon nanodots (PEG6000/CDs) and analyzed their potential in fluorescent staining of different types of bacteria. Our results demonstrated that PEG6000/CDs stained the cell pole and septa of gram-positive bacteria B. Subtilis and B. thuringiensis but not those of gram-negative bacteria. The optimal concentration of these composite nanodots was approximately 100 ppm and exposure times varied across different bacteria. The PEG6000/CD composite had better photostability and higher resistance to photobleaching than the commercially available FM4-64. They could emit two wavelengths (red and green) when exposed to two different wavelengths. Therefore, they may be applicable as bioimaging molecules. They can also be used for differentiating different types of bacteria owing to their ability to differentially stain gram-positive and gram-negative bacteria.

Removal of heavy oil using rhinoceros beetle, Oryctes rhinoceros.

The remnant of heavy oil, often expressed as total petroleum hydrocarbons (TPHs), in soil and/or sludge is commonly encountered by and often ruins the habitat of some indigenous insects. Recent studies indicate that some of the insects could stand the impact and some not just survived but might serve as an oil degrader. The potential of using indigenous insects in treating oil pollution is of interests in this study. In Asia, the potential oil-exposed rhinoceros beetle, Oryctes rhinoceros, was studied herein due to two major interests: one is its tolerance to heavy oil, and the other its ability to remove the oil. Two sets of the experiments spiked with different amounts of heavy oil were conducted in series, and the results of the larval mortality rate, growth rate, feces production, substrate conversion ratio and percent of oil removal were monitored as performance indicators during these treatments. The obtained results showed that the ingestion of heavy oil at a 5000 mg/kg level significantly deteriorated the survival rate (37% left) of the tested larvae, yet oil-experienced larvae could survive in up to 10,000 mg/kg of heavy oil (100% survived). As for the heavy oil removal via larval ingestion, at a 10,000 mg/kg level of oil in the substrate, the percent of weekly removal of heavy oil by larva ingestion was consistent throughout the second run at 56.4 ±â€¯5.6%. These results demonstrated the potential use of beetle larvae as a bioreactor in pollutant removal.

Bactericidal Effects of Oxidative Stress Generated by EDTA-Fe and Hydrogen Peroxide.

Hydrogen peroxide is widely used as a disinfectant by generating oxidative stress. The chelate of ethylenediaminetetraacetic acid (EDTA) and ferrous iron (EDTA-Fe) was used to increase oxidative stress and bactericidal effects. The Escherichia coli (E. coli) was added to a beef extract culture medium and treated with various doses of test reagents, including hydrogen peroxide, EDTA-Fe chelate, and antioxidants (vitamin C and vitamin E) . All reagents were scanned individually or in combination to trace potential interference in optical density (OD) measurements and eliminate reagent-related interference. Medium supplemented with 13.79 mM hydrogen peroxide resulted in a large increase in the mortality of E. coli, and the highest disinfection efficiency for EDTA-Fe was observed at a neutral pH. The death of the cell of E. coli was significantly inhibited by the presence of catalase, but not vitamins C and E, suggesting that hydroxyl radicals were not generated during the EDTA-Fe-hydrogen peroxide reaction.

Photo- and chemocatalytic oxidation of dyes in water.

Three commonly used dyes, Acid Red-114 (AR-114), Reactive Black-5 (RB-5), and Disperse Black EX-SF (DB-EX-SF), were treated in a pH-neutral liquid with ultraviolet (UV) light by two reactive methods: photocatalysis with titanium dioxide (TiO2), and/or chemocatalysis with hydrogen peroxide (H2O2) as the oxidant and various ferrous-based electron mediators as catalysts. Important factors for dye oxidation were determined through bifactorial experiments. The optimum combinations and doses of the three key reagents, namely TiO2, H2O2, and EDTA-Fe, were also determined. The degradation kinetics of the studied dyes at their optimum doses reveal that the oxidation reactions are pseudo-first-order in nature, and that certain dyes are selectively degraded more by one method than the other. The overall results suggest that co-treatment using more than one oxidative method is beneficial for the treatment of wastewater from dyeing processes.

Evaluation of the multiple-ion competition in the adsorption of As(V) onto reclaimed iron-oxide coated sands by fractional factorial design.

This study describes the competitive effects of selected ions and natural organic matter on As(V) removal using reclaimed iron-oxide coated sands (RIOCS) in the single- and multi-ion systems. A 2(7-3) factional factorial experimental design (FFD) was employed for screening main competitive factors in this adsorption process. As a result, the inhibitive competition effects of the anions on As(V) removal in the single ion system were in the following sequence: PO(4)(3-)>SiO(3)(2-)>HCO(3)(-)>humic acid (HA)>SO(4)(2-)>Cl(-), whereas the cation Ca(2+) was observed to enhance the As(V) removal. In addition, the optimum initial pH for As(V) removal in single-ion system was 5. Based on the estimates of major effects and interactions from the FFD, PO(4)(3-), SiO(3)(2-), Ca(2+) and HA were important factors on As(V) removal in the multi-ion system. The promoters for the As(V) removal were found to be Ca(2+) and, to a lesser extent, SO(4)(2-). The competitive effects of these ions on As(V) removal were in the order of PO(4)(3-), SiO(3)(2-), HA, HCO(3)(-), and Cl(-). In the single ion system, the efficiencies of As(V) removal range from 75% to 96%, much higher than those in the multi-ion system (44%) at the initial pH 5. Clearly, there were some complex anion interactions in the multi-ion system. To promote the removal of As(V) by RIOCS, it is proposed to lower the pH in the single-ion system, while in the multi-ion system, the increase of the Ca(2+) concentration, or decreases of PO(4)(3-), SiO(3)(2-) and HA concentrations is suggested.

Removal of As(V) and As(III) by reclaimed iron-oxide coated sands.

This paper aims at the feasibility of arsenate and arsenite removal by reclaimed iron-oxide coated sands (IOCS). Batch experiments were performed to examine the adsorption isotherm and removal performance of arsenic systems by using the IOCS. The results show that the pH(zpc) of IOCS was about 7.0 +/- 0.4, favoring the adsorption of As(V) of anion form onto the IOCS surface. As the adsorbent dosage and initial arsenic concentration were fixed, both the As(V) and As(III) removals decrease with increasing initial solution pH. Under the same initial solution pH and adsorbent dosage, the removal efficiencies of total arsenic (As(V) and As(III)) were in the order as follows: As(V)>As(V)+As(III)>As(III). Moreover, adsorption isotherms of As(V) and As(III) fit the Langmuir model satisfactorily for the four different initial pH conditions as well as for the studied range of initial arsenic concentrations. It is concluded that the reclaimed IOCS can be considered as a feasible and economical adsorbent for arsenic removal.