Influence of the Composition of Plasticizer-Free Silicone-Based Ion-Selective Membranes on Signal Stability in Aqueous and Blood Plasma Samples.

Solid-contact ion-selective electrodes (SC-ISEs) in direct long-term contact with physiological samples must be biocompatible and resistant to biofouling, but most wearable SC-ISEs proposed to date contain plasticized poly(vinyl chloride) (PVC) membranes, which have poor biocompatibility. Silicones are a promising alternative to plasticized PVC because of their excellent biocompatibility, but little work has been done to study the relationship between silicone composition and ISE performance. To address this, we prepared and tested K+ SC-ISEs with colloid-imprinted mesoporous (CIM) carbon as the solid contact and three different condensation-cured silicones: a custom silicone prepared in-house (Silicone 1), a commercial silicone (Dow 3140, Silicone 2), and a commercial fluorosilicone (Dow 730, Fluorosilicone 1). SC-ISEs prepared with each of these polymers and the ionophore valinomycin and added ionic sites exhibited Nernstian responses, excellent selectivities, and signal drifts as low as 3 µV/h in 1 mM KCl solution. All ISEs maintained Nernstian response slopes and had only very slightly worsened selectivities after 41 h exposure to porcine plasma (log KK,Na values of -4.56, -4.58, and -4.49, to -4.04, -4.00, and -3.90 for Silicone 1, Silicone 2, and Fluorosilicone 1, respectively), confirming that these sensors retain the high selectivity that makes them suitable for use in physiological samples. When immersed in porcine plasma, the SC-ISEs exhibited emf drifts that were still fairly low but notably larger than when measurements were performed in pure water. Interestingly, despite the very similar structures of these matrix polymers, SC-ISEs prepared with Silicone 2 showed lower drift in porcine blood plasma (-55 µV/h, over 41 h) compared to Silicone 1 (-495 µV/h) or Fluorosilicone 1 (-297 µV/h).

Solid-Contact pH Sensor with Covalent Attachment of Ionophores and Ionic Sites to a Poly(decyl methacrylate) Matrix.

With a view to improving the sensor lifetime, solid-contact ion-selective electrodes (ISEs) were prepared with a plasticizer-free and cross-linked poly(decyl methacrylate) matrix, to which only the ionic sites, only the ionophore, or both the ionic sites and ionophore were covalently attached. In earlier work with covalently attached ionophores or ionic sites, it was difficult to discount the presence of ionophores or ionic site impurities that were not covalently attached to the polymer backbone because the reagents used to introduce the ionophore or ionic sites had high hydrophobicities. In this work, we deliberately chose readily available hydrophilic reagents for the introduction of covalently attached H+ ionophores with tertiary amino groups and covalently attached sulfonate groups as ionic sites. This simplified the synthesis and made it possible to thoroughly remove ionophores and ionic sites not covalently attached to the polymer backbone. Our results confirm the expectation that hydrophobic ISE membranes with both covalently attached ionophores and ionic sites have impractically long response times. In contrast, ISEs with either covalently attached H+ ionophores or covalently attached ionic sites responded to pH with quick Nernstian responses and high selectivity. Both conventional plasticized poly(vinyl chloride) (PVC)-based ISEs and the new poly(decyl methacrylate) membranes were exposed to 90 °C heat for 2 h, 10% ethanol for 1 day, or undiluted blood serum for 5 days. In all three cases, the poly(decyl methacrylate) ISEs exhibited properties superior to conventional PVC-based ISEs, confirming the advantages of the covalent attachment.

Fluorous-Phase Ion-Selective pH Electrodes: Electrode Body and Ionophore Optimization for Measurements in the Physiological pH Range.

Because of their low polarity and polarizability, fluorous sensing membranes are both hydrophobic and lipophobic and exhibit very high ion selectivities. Here, we report on a new fluorous-membrane ion-selective electrode (ISE) with a wide sensing range centered around physiologically relevant pH values. The fluorophilic tris[perfluoro(octyl)butyl]amine (N[(CH2)4Rf8]3) was synthesized and tested as a new H+ ionophore using a redesigned electrode body that provides excellent mechanical sealing and much improved measurement reliability. In a challenging 1 M KCl background, these fluorous-phase ISEs exhibit a sensing range from pH 2.2 to 11.2, which is one of the widest working ranges reported to date for ionophore-based H+ ISEs. High selectivities against common interfering ions such as K+, Na+, and Ca2+ were determined (selectivity coefficients: logK H, K pot = - 11.6; logK H, Na pot = - 12.4; logK H, Ca pot < - 10.2). The use of the N[(CH2)4Rf8]3 ionophore with its -(CH2)4- spacers separating the amino group from the strongly electron-withdrawing perfluorooctyl groups improved the potentiometric selectivity as compared to the less basic tris[perfluoro(octyl)propyl]amine ionophore. The use of N[(CH2)4Rf8]3 also made the ISE less prone to counter anion failure (i.e., Donnan failure) at low pH than the use of tris[perfluoro(octyl)pentyl]amine with its longer -(CH2)5- spacers, which more effectively shield the amino center from the perfluorooctyl groups. In addition, we exposed both conventional plasticized PVC-phase pH ISEs and fluorous-phase pH ISEs to 10% serum for 5 days. Results show that the PVC-phase ISEs lost selectivity while their fluorous-phase counterparts did not.

Reference Electrodes Based on Ionic Liquid-Doped Reference Membranes with Biocompatible Silicone Matrixes.

Many reference electrodes with an ionic liquid-doped reference membrane contain a plasticizer that can gradually leach out into the sample. However, because many common plasticizers are known to be endocrine disruptors and may induce inflammatory reactions, they are preferably avoided for wearable or implantable sensors. Therefore, this work tested polymeric reference electrode membranes prepared by solvent casting from seven commercially available biocompatible silicones that are widely used in implantable devices. Only reference electrodes with membranes consisting of poly(3,3,3-trifluoropropylmethylsiloxane) (Fluorosilicone 1) and one of several 1-methyl-3-alkylimidazolium bis(trifluoromethylsulfonyl)imide ionic liquids provided a stable and sample-independent potential in electrolyte solutions spanning the range of electrolyte concentrations in human blood, with more hydrophobic ionic liquids performing better. Over 8 days at 37 °C in artificial blood electrolyte solutions, the reference membranes doped with 1-methyl-3-octylimidazolium bis(trifluoromethylsulfonyl)imide exhibited a potential drift as low as 20 µV/h. In 10% animal serum, a 112 µV/h drift was observed over 5.8 days. The other six silicone materials doped with an ionic liquid either failed to form self-standing membranes or did not provide a sample-independent potential in the ionic concentration range tested. In case of the functional reference electrodes, differential scanning calorimetry confirmed good miscibility between the ionic liquid and the polymer matrix, whereas the poor miscibility of four polymer matrixes and the ionic liquids-as confirmed by differential scanning calorimetry-correlated with an undesirable sample dependence of the reference potential.

Remediation of Perfluorooctylsulfonate Contamination by in Situ Sequestration: Direct Monitoring of PFOS Binding to Polyquaternium Polymers.

In situ methods for the sequestration of perfluorooctyl-1-sulfonate (PFOS) that are based on PFOS binding to polyquaternium polymers were reported previously, providing an approach to immobilize and concentrate PFOS in situ. To apply these methods in real life, the concentrations of polymers that permit efficient sequestration must be determined. This is only possible if the stoichiometry and strength of PFOS binding to polyquaternium polymers are known. Here, we report on the use of fluorous-phase ion-selective electrodes (ISEs) to determine the equilibrium constants characterizing binding of PFOS to poly(dimethylamine-co-epichlorohydrin) and poly(diallyldimethylammonium) in simulated groundwater and in soil suspensions. We introduce a new method to interpret potentiometric data for surfactant binding to the charged repeat unit of these polyions by combining a 1:1 binding model with the ISE response model. This allows for straightforward prediction and fitting of experimental potentiometric data in one step. Data fit the binding model for poly(diallyldimethylammonium) and poly(dimethylamine-co-epichlorohydrin) chloride in soil-free conditions and in the presence of soil from Tinker Air Force Base. When the total PFOS concentration in a soil system is known, knowledge of these PFOS binding characteristics permits quantitative prediction of the mobile (free) and polymer-bound fractions of PFOS as a function of the concentrations of the polyquaternium polymer. Because the technique reported here is based on the selective in situ determination of the free ionic surfactant, we expect it to be similarly useful for determining the sequestration of a variety of other ionic pollutants.

Potentiometric Selectivities of Ionophore-Doped Ion-Selective Membranes: Concurrent Presence of Primary Ion or Interfering Ion Complexes of Multiple Stoichiometries.

The selectivities of ionophore-doped ion-selective electrode (ISE) membranes are controlled by the stability and stoichiometry of the complexes between the ionophore, L, and the target and interfering ions (I zi and J zj, respectively). Well-accepted models predict how these selectivities can be optimized by selection of ideal ionophore-to-ionic site ratios, considering complex stoichiometries and ion charges. These models were developed for systems in which the target and interfering ions each form complexes of only one stoichiometry. However, for a few ISEs, the concurrent presence of two primary ion complexes of different stoichiometries, such as IL zi and IL2 zi, was reported. Indeed, similar systems were probably often overlooked and are, in fact, more common than the exclusive formation of complexes of higher stoichiometry unless the ionophore is used in excess. Importantly, misinterpreted stoichiometries misguide the design of new ionophores and are likely to result in the formulation of ISE membranes with inferior selectivities. We show here that the presence of two or more complexes of different stoichiometries for a given ion may be inferred experimentally from careful interpretation of the potentiometric selectivities as a function of the ionophore-to-ionic site ratio or from calculations of complex concentrations using experimentally determined complex stabilities. Concurrent formation of JL zj and JL2 zj complexes of an interfering ion is shown here to shift the ionophore-to-ionic site ratio that provides the highest selectivities. Formation of IL n-1 zi and IL n zi complexes of a primary ion is less of a concern because an optimized membrane typically contains an excess of ionophore, but lower than expected selectivities may be observed if the stepwise complex formation constant, KILn, is not sufficiently large and the ionophore-to-ionic site ratio does not markedly exceed n.

Ion Aggregation and R3N+-C(R)-H···NR3 Hydrogen Bonding in a Fluorous Phase.

Potentiometric selectivities show that in fluorous ion-selective electrode membranes the tetrabutylammonium ion binds to fluorophilic proton ionophores. For the ionophore bis[3-(perfluorooctyl)propyl](2,2,2-trifluoroethyl)amine, this type of interaction is confirmed by the effect of the ionophore on the ionic conductivity of perfluoro(perhydrophenanthrene) solutions of a fluorophilic NBu4+ salt. In this system, ion pairs, triple ions, and higher ionic aggregates dominate over single ions, and the ionophore increases the conductivity by favoring the formation of ion aggregates with a net charge. These observations are consistent with the formation of R3N+-C(R)-H···NR3 type hydrogen bonds between the nitrogen atom of the ionophore and the hydrogen atoms in the α position to the positively charged quaternary ammonium center of NBu4+. Similar interactions were observed in a number of crystalline phases. To date, observations of C-H···N type hydrogen bonds in liquid phases have been very few, and solution-phase N+-C-H···N type hydrogen bonds have not been reported previously. Interestingly, no interactions between NBu4+ and the more basic ionophore tridodecylamine were observed in conventional plasticized poly(vinyl chloride) membranes doped with the ionophore tridodecylamine, emphasizing the uniquely low polarity of fluorous phases.