RESUMEN
OBJECTIVE: Polymethyl methacrylate (PMMA) is one of the most widely used denture base material because of favorable esthetics and desirable characteristics such as easy handling. Acrylic resins, although, have some inherent disadvantages such as relatively poor physical and mechanical properties. The objective of the present study was to evaluate and compare the impact strength of unmodified and modified heat cure PMMA-based denture base material with addition of different concentrations of silver nanoparticles (AgNPs) (0.5, 1, 2 wt%). METHODS: The present in-vitro study comprised of a total of 60 samples allocated to four groups with Group A samples consisting of heat cure acrylic resin without any modification (used as control); Group B samples consisting of heat cure acrylic resin modified with 0.5 wt% of AgNPs; and subsequently, Group C and Group D samples consisting of heat cure acrylic resin modified with 1 wt% and 2 wt% of AgNPs, respectively. The impact strength of the prepared acrylic samples was evaluated using Izod/Charpy Impact Tester, while the values obtained were tabulated and subjected to statistical analysis. Statistical analysis was done using Statistical Package for Social Sciences (SPSS) version 17.0 (SPSS Inc., Chicago, IL, USA), while one-way analysis of variance and Tukey's multiple post-hoc procedures were used for statistical analysis. P < .05 was considered statistically significant. RESULTS: The highest impact strength was found in Group C samples consisting of heat cure acrylic resin modified with 1 wt% of AgNPs to be closely followed by Group B samples consisting of heat cure acrylic resin modified with 0.5 wt% of AgNPs. Group D samples consisting of heat cure acrylic resin modified with 2 wt% of AgNPs, although, revealed relatively lower impact strength compared to Group B and Group C samples. CONCLUSIONS: Within the limitations of the present study, it was concluded that the impact strength of mechanically modified heat polymerized PMMA resin was significantly enhanced with addition of varying concentrations of AgNPs, although, it was observed that with an increase in the concentration of AgNPs, a subsequent decrease in the tensile strength of the final polymer material was observed.
RESUMEN
OBJECTIVE: The contemporary esthetic restorative materials such as composite resin and glass-ionomer cements and their modifications have all been developed keeping in mind the requirements of permanent teeth. There have been plenty of studies that have focused on the characteristics of these materials in relation to permanent teeth with a relative dearth of such studies as regard to the primary teeth. The present study was undertaken to compare and evaluate the shear bond strength of composite resin, compomer, and resin-modified glass-ionomer cements in primary teeth. METHODS: Thirty non-carious primary molars that were indicated for extraction because of physiological resorption or, for orthodontic reasons, were selected. The selected teeth were randomly allocated to three groups of 10 each for composite, compomer, and resin-modified glass-ionomer cements. The enamel from the occlusal surface of all teeth was removed to expose the superficial dentin and was wet polished with 400 grit sand paper. Composite, compomer, and resin-modified glass-ionomer stubs were bonded on to the occlusal surfaces using a plastic tube as a template. All samples were, then, subjected to thermocycling and evaluation of shear bond strength using the universal testing machine at a cross-head speed of 0.5 mm/min, whereas the results obtained were subjected to statistical analysis. Statistical analysis was performed using Statistical Package for Social Sciences (SPSS) version 17.0 (SPSS Inc., Chicago, IL, USA), whereas one-way analysis of variance (ANOVA) and Tukey's multiple post-hoc procedures were used for statistical analysis. A P < 0.05 was considered statistically significant. RESULTS: The mean shear bond strength values for Groups I, II, and III were found to be 11.7 ± 3.07 MPa, 7.74 ± 4.16 Mpa, and 4.43 ± 2.08 Mpa, respectively, whereas one-way ANOVA and Tukey's multiple post-hoc procedures indicated that there were remarkable differences among the three groups with the results being statistically significant (P < 0.05). CONCLUSIONS: Composite resin showed the highest shear bond strength in relation to primary dentin when compared to compomer and resin-modified glass-ionomer cements.