RESUMEN
Lithium metal is a promising anode candidate to achieve high-energy-density lithium metal batteries (LMBs) due to its ultrahigh theoretical capacity (3860 mA h g-1) and low electrochemical potential (-3.04 V vs S.H.E). Unfortunately, the commercialization of lithium metal anodes is hindered by the growth of Li dendrites and the infinite Li volume changes during the cycling process. Herein, we introduce a 3D hierarchical multimetal oxide nanowire framework as a current collector for Li metal anodes. The hierarchical metal oxide layers of CoO and CuxO provide abundant Li nucleation sites and thus offer uniform Li plating and regulate Li nucleation during the charge/discharge process. As a result, half cells present a prolonging Coulombic efficiency of 97% at 1 mA cm-2 with a capacity of 1 mA h cm-2 for over 300 cycles. A stable cyclability of symmetric cells is demonstrated under 1 mA cm-2 with a capacity of 1 mA h cm-2 for 1500 h. Full cells paired with an LFP cathode show a stable capacity of 131.5 mA h g-1 with a capacity retention of 92% for 200 cycles. These results will shed insights into the design of 3D Cu current collectors for high-performance composite Li metal anodes.
RESUMEN
In this study, a strategy for the rapid and simple preparation of porous carbon (PC) using the microwave method was proposed. Oxygen-rich PC was synthesized by microwave irradiation in air, where potassium citrate and ZnCl2 served as the carbon source and microwave absorber, respectively. ZnCl2 achieves microwave absorption through dipole rotation, which uses ion conduction to convert heat energy in the reaction system. In addition, potassium salt etching improved the porosity of PCs. The PC prepared under optimal conditions had a large specific surface area (902 m2·g-1) and exhibited a significant specific capacitance (380 F·g-1) in the three-electrode system at 1 A·g-1. The energy and power densities of the assembled symmetrical supercapacitor device based on PC-375W-0.4 were 32.7 W·h·kg-1 and 0.65 kW·kg-1, respectively, at a current density of 1 A·g-1. Even after 5000 cycles at 5 A·g-1 current density, the excellent cycle life retained 94% of its initial capacitance.
RESUMEN
Silicon microparticles (SiMPs) show considerable promise as an anode material in high-performance lithium-ion batteries (LIBs) because of their low-cost starting material and high capacity. The failure issues associated with the intrinsically low conductivity and significant volume expansion of Si have largely been resolved by designing silicon/carbon composites using carbon nanotubes (CNTs). The CNTs are important in terms of stress dissipation and the conductive network in Si/CNT composites. Here, we synthesized a SiMP/2D CNT sheet wrapping composite (SiMP/CNT wrapping) via a facile freeze-drying method with the use of highly dispersed single-walled CNTs. In this work, the well-dispersed CNTs are easily mixed with Si, resulting in effective CNT wrapping on the SiMP surface. During freeze-drying, the CNTs are self-assembled into a segregated 2D CNT sheet morphology via van der Waals interactions. The resulting CNT wrapping shows a unique wide range of conductive networks and mesh-like CNT sheets with void spaces. The SiMP/CNT wrapping 9 : 1 electrode exhibits good rate and cycle performance. The first charge/discharge capacity of SiMP/CNT wrapping 9 : 1 is 3160.7 mA h g-1/3469.1 mA h g-1 at 0.1 A g-1 with superior initial coulombic efficiency of 91.11%. After cycling, the SiMP/CNT wrapping electrode shows good structural integrity with preserved electrical conductivity. The superior electrochemical performance of the SiMP/CNT wrapping composite can be explained by an extensive conductive CNT network on the SiMPs and facile lithium-ion diffusion via mesh-like CNT wrapping.
RESUMEN
Recent studies of lithium-sulfur (Li-S) batteries have identified that a modified separator plays a critical role in challenging the capacity fading and shuttle effect of lithium polysulfides (LiPSs). Herein, we report a polyaniline-encapsulated hollow Co-Fe Prussian blue analogue (CFP@PANI) for separator modification. The open frame-like hollow CFP was synthesized via oriented attachment (OA). To improve the catalytic effect and electrical conductivity, PANI was coated on the synthesized CFP. The resulting CFP@PANI was applied on the conventional polypropylene (PP) separator (CFP@PANI-PP) with vacuum filtration. With a ketjen black/sulfur (KB/S) cathode with 66% of the sulfur load, the CFP@PANI-PP exhibited an initial capacity of 723.1 mAh g-1 at a current density of 1 A g-1. Furthermore, the CFP@PANI-PP showed stable cycling performance with 83.5% capacity retention after 100 cycles at 1 A g-1. During the 100 cycles, each cycle maintained high coulombic efficiency above 99.5%, which indicates that the CFP@PANI-PP could inhibit LiPS migration to the anode side without a Li+ transport disturbance across the separator. Overall, the CFP@PANI-PP efficiently suppressed LiPSs, resulting in enhanced electrochemical performance. The current study provides useful insight into designing a nanostructure for separator modification of Li-S batteries.
