Synthesis of rGO/CoFe2O4 Composite and Its Magnetorheological Characteristics.

In this study, composite particles of rGO/CoFe2O4 were synthesized using a solvothermal method to fabricate a low-density magnetorheological (MR) material with enhanced sedimentation stability. The morphology and crystallographic features of rGO/CoFe2O4 were characterized via SEM, TEM, and XRD, and its magnetic properties were tested using VSM. The MR fluid was formulated by blending rGO/CoFe2O4 particles into silicone oil. Under different magnet strengths (H), a rotational rheometer was used to test its MR properties. Typical MR properties were observed, including shear stress, viscosity, storage/loss modulus, and dynamic yield stress (τdy) following the Herschel-Bulkley model reaching 200 Pa when H is 342 kA/m. Furthermore, the yield stress of the MR fluid follows a power law relation as H increases and the index changes from 2.0 (in the low H region) to 1.5 (in the high H region). Finally, its MR efficiency was calculated to be about 104% at H of 342 kA/m.

Synergistic Inclusion Effects of Hard Magnetic Nanorods on the Magnetomechanical Actuation of Soft Magnetic Microsphere-Based Polymer Composites.

The magnetomechanical actuation of micropillars is developed for the contactless manipulation of miniaturized actuators and microtextured surfaces. Anisotropic geometry of micropillars can significantly enhance the magnetic actuation compared with their isotropic counterparts by directional stress distributions. However, this strategy is not viable for triangular micropillars owing to insufficient anisotropy. In this study, a significant improvement in the magnetic actuation of triangular micropillars using composite magnetic particles is reported. A minute and optimal amount of hard magnetic gamma-ferrite nanorods are hybridized with soft magnetic iron microspheres to generate synergistic effects of magnetic coupling and percolation phenomenon on the magnetic actuation of polymer composites. The addition of 1 wt% face-centered cubic-phased gamma-ferrite nanorods suppresses the magnetic coupling interference of body-centered cubic-phased iron microspheres. Furthermore, the nanorods reduce the percolation threshold by participating in the percolation of the microspheres. A systematic compositional study on the magnetization and magnetorheological properties reveals that the coupling effect dominates the percolation effect at a low magnetic field, whereas the percolation effect governs the magnetic actuation at a high magnetic field. This hybrid approach can help in designing material constituents for effective magnetic actuators and robotic systems that can sensitively respond to an external magnetic field.

Passive Electrical Components Based on Cotton Fabric Decorated with Iron Oxides Microfibers: The Influence of Static and Pulsed Magnetic Fields on the Equivalent Electrical Properties.

In this work, environmentally friendly and low-cost passive electrical components (PECs) are manufactured based on composites consisting of cotton fabrics soaked with solutions of silicone oil and different amounts of iron oxides microfibers (µFe). The µFe consists of a mixture of three phases: hematite (α-Fe2O3), maghemite (γ-Fe2O3), and magnetite (Fe3O4). The equivalent electrical capacitance (Cp) and resistance (Rp) of PECs are measured as a function of magnetic flux density B in a static and pulsed magnetic field superimposed on an alternating electric field of frequency 1 kHz. The relative variation in the hysteresis curves for both Cp and Rp are obtained by measuring them in the ascending and then the descending mode of B. We show that all these three quantities are sensibly influenced by the volume fractions of µFe and by the values of B. The main influence on this behavior is attributed to the semiconductor properties of the α-Fe2O3 and γ-Fe2O3 components of the oxide microfibers. In addition, it is found that at B≃ 175 mT, the maximum relative variance of the hysteresis curve is about 3.35% for Cp and 3.18 % for Rp. When a pulsed magnetic field is used, it is shown that Cp and Rp closely follow the variation in the magnetic field. Thus, the resulting electrical properties of PECs, together with the fast response to the application of pulsed magnetic fields, make them useful in the fabrication of various devices, such as electric, magnetic, and deformation fields, or mechanical stress sensors with applications in protection against electromagnetic smog, healthcare monitoring, or for human-machine interfacing.

Rheological Characteristics of Starch-Based Biodegradable Blends.

Thermoplastic starch was blended with commercially available biodegradable polyesters of poly(butylene adipate-co-terephthalate) (PBAT) and poly(lactic acid) (PLA) for its improved performance and processability. The morphology and elemental composition of these biodegradable polymer blends were observed by scanning electron microscopy and energy dispersive X-ray spectroscopy, respectively, while their thermal properties were analyzed using thermogravimetric analysis and differential thermal calorimetry. For rheological analysis, the steady shear and dynamic oscillation tests of three samples at various temperatures were investigated using a rotational rheometer. All three samples exhibited significant shear thinning at all measured temperatures, and their shear viscosity behavior was plotted using the Carreau model. The frequency sweep tests showed that the thermoplastic starch sample exhibited a solid state at all temperatures tested, whereas both starch/PBAT and starch/PBAT/PLA blend samples exhibited viscoelastic liquid behavior after the melting temperature such that their loss modulus at low frequencies was greater than the storage modulus, and inversion occurred at high frequencies (storage modulus > loss modulus).

Effect of Rheological Properties of Polymer Solution on Polymer Flooding Characteristics.

Polymer flooding is an appropriate enhanced oil recovery (EOR) process that can increase macroscopic sweep efficiency. We examined two polymeric superpushers at different salinities (10,000 and 42,000 ppm of NaCl and 18,000 ppm of CaCl2) and temperatures (30 to 75 °C) as polymer-flooding agents for the EOR process. Rheological and thixotropic tests were attempted to find shear viscosity change when the polymer solutions were introduced under different salinity and temperatures, followed by describing the rheological behavior with the two most common rheological models used for polymer solutions, and then a quadratic model with Design-Expert to detect the effective parameters. Core flooding tests were conducted afterward to determine the final proposed fluid. An increase in the concentration of monovalent ions and the addition of divalent ions adversely affected both types of polymers used, which was similar to the effects of a temperature increase. The Flopaam 3630S at 1000 ppm has more stability under harsh conditions and enables 22% and 38% oil recovery in carbonate and sandstone core rocks, respectively. Consequently, Flopaam 3630S can be the perfect polymer agent for different chemical flooding procedures in high-salinity oil reservoirs.

Hollow TiO2 Nanoparticles Capped with Polarizability-Tunable Conducting Polymers for Improved Electrorheological Activity.

Hollow TiO2 nanoparticles (HNPs) capped with conducting polymers, such as polythiophene (PT), polypyrrole (PPy), and polyaniline (PANI), have been studied to be used as polarizability-tunable electrorheological (ER) fluids. The hollow shape of TiO2 nanoparticles, achieved by the removal of the SiO2 template, offers colloidal dispersion stability in silicone oil owing to the high number density. Conducting polymer shells, introduced on the nanoparticle surface using vapor deposition polymerization method, improve the yield stress of the corresponding ER fluids in the order of PANI < PPy < PT. PT-HNPs exhibited the highest yield stress of ca. 94.2 Pa, which is 5.0-, 1.5-, and 9.6-times higher than that of PANI-, PPy-, and bare HNPs, respectively. The improved ER response upon tuning with polymer shells is attributed to the space charge contribution arising from the movement of the charge carriers trapped by the heterogeneous interface. The ER response of studied ER fluids is consistent with the corresponding polarizability results as indicated by the permittivity and electrophoretic mobility measurements. In conclusion, the synergistic effect of hollow nanostructures and conducting polymer capping effectively enhanced the ER performance.

Development of Novel Colorful Electrorheological Fluids.

Herein, the electrorheological (ER) performances of ER fluids were correlated with their colors to allow for the visual selection of the appropriate fluid for a specific application using naked eyes. A series of TiO2-coated synthetic mica materials colored white, yellow, red, violet, blue, and green (referred to as color mica/TiO2 materials) were fabricated via a facile sol-gel method. The colors were controlled by varying the thickness of the TiO2 coating layer, as the coatings with different thicknesses exhibited different light interference effects. The synthesized color mica/TiO2 materials were mixed with silicone oil to prepare colored ER fluids. The ER performances of the fluids decreased with increasing thickness of the TiO2 layer in the order of white, yellow, red, violet, blue, and green materials. The ER performance of differently colored ER fluids was also affected by the electrical conductivity, dispersion stability, and concentrations of Na+ and Ca2+ ions. This pioneering study may provide a practical strategy for developing new ER fluid systems in future.

Dual Electrorheological and Magnetorheological Behaviors of Poly(N-methyl aniline) Coated ZnFe2O4 Composite Particles.

Magnetic/conducting polymeric hybrid core-shell typed zinc ferrite (ZnFe2O4)/poly(N-methyl aniline) (PMA) particles were fabricated and adopted as electrorheological (ER) and magnetorheological (MR) fluids, and their rheological properties were examined. Solvo-thermally synthesized ZnFe2O4 was coated with a conducting PMA through chemical oxidation polymerization. The size, shape, and chemical composition of the final core-shell shaped particles were scrutinized by scanning electron microscopy, transmission electron microscopy, and Fourier transform-infrared spectroscopy. The crystal faces of the particles before and after coating with PMA were analyzed by X-ray diffraction. The ZnFe2O4/PMA products were suspended in silicone oil to investigate the rheological response to electro- or magnetic stimuli using a rotating rheometer. The shear stresses were analyzed using the CCJ equation. The dynamic yield stress curve was suitable for the conductivity mechanism with a slope of 1.5. When magnetic fields of various intensities were applied, the flow curve was analyzed using the Hershel-Bulkley equation, and the yield stresses had a slope of 1.5. Optical microscopy further showed that the particles dispersed in insulating medium form chain structures under electric and magnetic fields. Via this core-shell fabrication process, not only spherical conducting particles were obtained but also their dual ER and MR responses were demonstrated for their wide potential applications.

An overview on the enhanced gas condensate recovery with novel and green methods.

A consideration of the negative environmental aspects of fossil fuels has made natural gas the best choice to meet the human demand for energy. The condensate gas reservoir is one source of gases that tolerates skin problems (liquid blockage). Conventional methods for inhibiting or removing liquid blockages are momentary treatments, non-eco-friendly, and expensive. Therefore, new methods have been introduced, such as wettability alteration toward liquid repellency, renewable energies, thermochemical reactions and waves for heating reservoirs, and CO2 injection. This paper reviews the methods for altering the wettability of porous media by fluorochemicals, fluorinated nanoparticles (NPs), and free fluorocarbon materials from natural substances. NPs, particularly silicon-based types, as a green, clean, and emerging technology that are more compatible with the environment, were investigated for their ability to alter the wettability and upgrade conventional materials, such as polymers and surfactants. The feasibility of using renewable energies, thermochemical reactions, and waves for heating the gas condensate reservoir to overcome the skin problem and return the reservoir to the reasonable and economical gas production is reviewed. Finally, CO2 injection is introduced as a multi-purpose green method to enhance gas condensate recovery and allow CO2 sequestration.

Effect of drag-reducing polymer on blood flow in microchannels.

Drag-reducing polymers (DRPs) can significantly improve blood circulation when added to blood at a nanomolar concentration, manifesting great potential for application in the biomedical field. In this work, hyaluronic acid (HA) was selected as a natural DRP, and its effects on blood microcirculation at different concentrations, flow rates, and channel geometry were studied in microchannels. The experimental results show that adding a small dose of HA can increase the velocity and shorten the thickness of the cell-free layer (CFL or cell depletion layer (CDL)) near the wall. After considering efficiency, our experiments determined 50 ppm addition of HA to be the most suitable amount for improving blood circulation. Our results demonstrate that HA has high efficiency in improving the circulation of blood flow and shed light on unveiling the mechanism of using natural DRPs to cure some cardiovascular diseases.

Artificial Neural Network to Forecast Enhanced Oil Recovery Using Hydrolyzed Polyacrylamide in Sandstone and Carbonate Reservoirs.

Polymer flooding is an important enhanced oil recovery (EOR) method with high performance which is acceptable and applicable on a field scale but should first be evaluated through lab-scale experiments or simulation tools. Artificial intelligence techniques are strong simulation tools which can be used to evaluate the performance of polymer flooding operation. In this study, the main parameters of polymer flooding were selected as input parameters of models and collected from the literature, including: polymer concentration, salt concentration, rock type, initial oil saturation, porosity, permeability, pore volume flooding, temperature, API gravity, molecular weight of the polymer, and salinity. After that, multilayer perceptron (MLP), radial basis function, and fuzzy neural networks such as the adaptive neuro-fuzzy inference system were adopted to estimate the output EOR performance. The MLP neural network had a very high ability for prediction, with statistical parameters of R2 = 0.9990 and RMSE = 0.0002. Therefore, the proposed model can significantly help engineers to select the proper EOR methods and API gravity, salinity, permeability, porosity, and salt concentration have the greatest impact on the polymer flooding performance.

Magnetite/Poly(ortho-anisidine) Composite Particles and Their Electrorheological Response.

Magnetic and semiconducting Fe3O4/poly(o-anisidine) (POA) core/shell composite particles were fabricated by an oxidation process using Fe3O4 synthesized separately. The dispersion stability in a liquid medium and the electrical conductivity of synthesized particles were improved because of the conductive POA polymeric shell. The morphological, microstructural, compositional/elemental, and thermal behaviors of the particles were characterized using SEM with energy dispersive X-ray spectroscopy, TEM, XRD, and thermogravimetric analysis, respectively. A smart electro-magneto-rheological suspension containing Fe3O4/POA particles with two functionalities, magnetism and conductivity, was prepared. Its electrorheological properties were investigated at different electric field strengths using a rotational rheometer. Without an electric field, the sample demonstrated typical Newtonian fluid behavior, as expected. However, while under the electric field, it exhibited a solid-like behavior, and the dynamic (or elastic) yield stress of the ER fluid increased linearly as a function of the electric field strength in a power-law function with an index of 2.0, following the polarization mechanism.

Core-Shell Structured Magnetite-Poly(diphenylamine) Microspheres and Their Tunable Dual Response under Magnetic and Electric Fields.

Core-shell type poly(diphenylamine)-coated magnetite (Fe3O4-PDPA) microspheres were designed and adopted as a novel actively tunable smart material which is responsive under both electric and magnetic fields. Their morphology, chemical structure, crystalline structure, and thermal properties were characterized using scanning electron microscopy, transmission electron microscope, Fourier transform-infrared spectroscopy, X-ray diffraction, and a thermal gravimetric analyzer. Their magnetic and dielectric properties were determined using vibrating-sample magnetometer and an LCR meter, respectively. They were dispersed in silicone oil and their electrorheological (ER) and magnetorheological (MR) responses under the electric and magnetic fields, respectively, were examined. The formation of chain structure of Fe3O4-PDPA based E/MR fluid under the application of electric field or magnetic field was observed by an optical microscopy and the sedimentation stability was observed by a Turbiscan optical analyzer system. It was observed that the yield stress, ER efficiency, and leakage current density increased with an increase in the particle concentration, while the slope of the electric field-dependent yield stress decreased. Several models such as the Bingham model, Herschel-Bulkley model, and Cho-Choi-Jhon equations were used to describe the shear stress curves of the ER fluid; the curves fitted well. For the dielectric properties, the two types of ER fluids tested displayed the same relaxation time and distribution; however, the one with the higher concentration had a higher dielectric constant and polarizability. The Fe3O4-PDPA based MR fluid (10 vol %) exhibited typical MR properties. In addition, the Herschel-Bulkley model matched well with the shear stress curves under a magnetic field.

Magnetic Polymer Composite Particles: Design and Magnetorheology.

As a family of smart functional hybrid materials, magnetic polymer composite particles have attracted considerable attention owing to their outstanding magnetism, dispersion stability, and fine biocompatibility. This review covers their magnetorheological properties, namely, flow curve, yield stress, and viscoelastic behavior, along with their synthesis. Preparation methods and characteristics of different types of magnetic composite particles are presented. Apart from the research progress in magnetic polymer composite synthesis, we also discuss prospects of this promising research field.

Dynamic Response of Polyindole Coated Zinc Ferrite Particle Suspension under an Electric Field.

ZnFe2O4 particles initially synthesized through a simple solvothermal method were coated using polyindole (PIn) to prepare an actively controllable core-shell typed hybrid material under both electric and magnetic fields. An advantage of this process is not needing to add the stabilizers or surfactants commonly used for uniform coating when synthesizing core or shell-structured particles. The synthesized ZnFe2O4/PIn particles have a lower density than conventional magnetic particles and have suitable properties as electrorheological (ER) particles. The expected spherical shape of the particles was proven using both scanning electron microscopy and transmission electron microscopy. The chemical characterization was performed using Fourier-transform infrared spectroscopy and X-ray diffraction analysis. To analyze the rheological properties, a ZnFe2O4/PIn based suspension was prepared, and dynamic rheological measurements were performed for different electric field strengths using a rotary rheometer. Both dynamic and elastic yield stresses of the ER fluid had a slope of 1.5, corresponding to the conductivity model. Excellent ER effect was confirmed through rheological analysis, and the prepared ER fluid had a reversible and immediate response to repeated electric fields.

Magnetorheological Elastomers: Fabrication, Characteristics, and Applications.

Magnetorheological (MR) elastomers become one of the most powerful smart and advanced materials that can be tuned reversibly, finely, and quickly in terms of their mechanical and viscoelastic properties by an input magnetic field. They are composite materials in which magnetizable particles are dispersed in solid base elastomers. Their distinctive behaviors are relying on the type and size of dispersed magnetic particles, the type of elastomer matrix, and the type of non-magnetic fillers such as plasticizer, carbon black, and crosslink agent. With these controllable characteristics, they can be applied to various applications such as vibration absorber, isolator, magnetoresistor, and electromagnetic wave absorption. This review provides a summary of the fabrication, properties, and applications of MR elastomers made of various elastomeric materials.

Melt Rheology and Mechanical Characteristics of Poly(Lactic Acid)/Alkylated Graphene Oxide Nanocomposites.

Poly(lactic acid) (PLA) nanocomposites were synthesized by a solution blending and coagulation method using alkylated graphene oxide (AGO) as a reinforcing agent. Turbiscan confirmed that the alkylation of GO led to enhanced compatibility between the matrix and the filler. The improved dispersity of the filler resulted in superior interfacial adhesion between the PLA chains and AGO basal plane, leading to enhanced mechanical and rheological properties compared to neat PLA. The tensile strength and elongation at break, i.e., ductility, increased by 38% and 42%, respectively, at the same filler content nanocomposite (PLA/AGO 1 wt %) compared to nonfiller PLA. Rheological analysis of the nanocomposites in the molten state of the samples was performed to understand the filler network formed inside the matrix. The storage modulus increased significantly from PLA/AGO 0.5 wt % (9.6 Pa) to PLA/AGO 1.0 wt % (908 Pa). This indicates a percolation threshold between the two filler contents. A steady shear test was performed to examine the melt flow characteristics of PLA/AGO nanocomposites at 170 °C, and the viscosity was predicted using the Carreau-Yasuda model.

Synthesis and Electrorheological Response of Graphene Oxide/Polydiphenylamine Microsheet Composite Particles.

Conducting graphene oxide/polydiphenylamine (GO/PDPA) microsheet nanocomposite particles were fabricated via in-situ oxidative polymerization using diphenylamine in the presence of GO. The morphological structures and dimensions of the fabricated GO/PDPA composites were evaluated using transmission electron microscopy and scanning electron microscopy. Electrorheological (ER) responses and creep behaviors of an ER fluid consisting of the GO/PDPA composites when suspended in silicone oil were evaluated using a rotational rheometer under input electric field. Three different types of yield stresses were examined along with dielectric analysis, demonstrating their actively tunable ER behaviors.

Bio-Inspired Passion Fruit-like Fe3O4@C Nanospheres Enabling High-Stability Magnetorheological Performances.

Magnetorheological (MR) fluids have been successfully utilized in versatile fields but are still limited by their relatively inferior long-term dispersion stability. Herein, bio-inspired passion fruit-like Fe3O4@C nanospheres were fabricated via a simple hydrothermal and calcination approach to tackle the settling challenge. The unique structures provide sufficient active interfaces for the penetration of carrier mediums, leading to preferable wettability between particles and medium oils. Compared with the bare Fe3O4 nanoparticle suspension, the resulting Fe3O4@C nanosphere-based MR fluid exhibits desirable stability and relatively low field-off viscosity even at a high particle concentration up to 35 vol %.

Pickering Emulsion Polymerized Polyaniline/Zinc-ferrite Composite Particles and Their Dual Electrorheological and Magnetorheological Responses.

A functional raspberry-like core-shell composite particle consisting of a conducting polyaniline (PANI) core and magnetic zinc ferrite shell is synthesized by Pickering emulsion polymerization. The morphology and chemical structure of the PANI/zinc-ferrite composite are evaluated by scanning electron microscopy, transmission electron microscopy, and Fourier-transform infrared spectroscopy. An electrorheological/magnetorheological fluid consisting of the PANI/zinc-ferrite composite dispersed in silicone oil with a particle concentration of 5 vol % is fabricated. Its rheological characteristics under external electric and magnetic fields are investigated by using a rotational rheometer. Under the electric or magnetic field, the PANI/zinc-ferrite particles form chain-like structures, demonstrating a solid-like state.