Artificial Weathering Test Methods of Waterborne Acrylic Coatings for Steel Structure Corrosion Protection.

Corrosion protection technologies based on waterborne paints have become increasingly popular as steel structure protection, which implies the need to determine relevant assessment methods considering the conditions of use and product-specific characteristics. This study attempts to evaluate the fitness of standard corrosion protection weathering methods and an original cyclic test for verifying the resistance of waterborne acrylic coatings to environmental conditions. Changes to the properties of artificially weathered coatings were analysed with reference to those observed during exposure in natural conditions. The degree of coating degradation after exposure to neutral salt spray and condensation humidity was determined to significantly exceed the changes observed in natural conditions. An original cyclic test caused changes in the appearance, microstructure, FT-IR spectrum and utility properties of the coatings, such as thickness, colour, hardness, adhesion and impedance, similar to those observed in the natural environment. The results confirm that the programming direction of waterborne coatings artificial weathering tests is adequate and promising.

Indocyanine green and iohexol loaded hydroxyapatite in poly(L-lactide-co-caprolactone)-based composite for bimodal near-infrared fluorescence- and X-ray-based imaging.

This study aimed to develop material for multimodal imaging by means of X-ray and near-infrared containing FDA- and EMA-approved iohexol and indocyanine green (ICG). The mentioned contrast agents (CAs) are hydrophilic and amphiphilic, respectively, which creates difficulties in fabrication of functional polymeric composites for fiducial markers (FMs) with usage thereof. Therefore, this study exploited for the first time the possibility of enhancing the radiopacity and introduction of the NIR fluorescence of FMs by adsorption of the CAs on hydroxyapatite (HAp) nanoparticles. The particles were embedded in the poly(L-lactide-co-caprolactone) (P[LAcoCL]) matrix resulting in the composite material for bimodal near-infrared fluorescence- and X-ray-based imaging. The applied method of material preparation provided homogenous distribution of both CAs with high iohexol loading efficiency and improved fluorescence signal due to hindered ICG aggregation. The material possessed profound contrasting properties for both imaging modalities. Its stability was evaluated during in vitro experiments in phosphate-buffered saline (PBS) and foetal bovine serum (FBS) solutions. The addition of HAp nanoparticles had significant effect on the fluorescence signal. The X-ray radiopacity was stable within minimum 11 weeks, even though the addition of ICG contributed to a faster release of iohexol. The stiffness of the material was not affected by iohexol or ICG, but incorporation of HAp nanoparticles elevated the values of bending modulus by approximately 70%. Moreover, the performed cell study revealed that all tested materials were not cytotoxic. Thus, the developed material can be successfully used for fabrication of FMs.

On the Effect of Non-Thermal Atmospheric Pressure Plasma Treatment on the Properties of PET Film.

The aim of the work was to investigate the effect of non-thermal plasma treatment of an ultra-thin polyethylene terephthalate (PET) film on changes in its physicochemical properties and biodegradability. Plasma treatment using a dielectric barrier discharge plasma reactor was carried out in air at room temperature and atmospheric pressure twice for 5 and 15 min, respectively. It has been shown that pre-treatment of the PET surface with non-thermal atmospheric plasma leads to changes in the physicochemical properties of this polymer. After plasma modification, the films showed a more developed surface compared to the control samples, which may be related to the surface etching and oxidation processes. After a 5-min plasma exposure, PET films were characterized by the highest wettability, i.e., the contact angle decreased by more than twice compared to the untreated samples. The differential scanning calorimetry analysis revealed the influence of plasma pretreatment on crystallinity content and the melt crystallization behavior of PET after soil degradation. The main novelty of the work is the fact that the combined action of two factors (i.e., physical and biological) led to a reduction in the content of the crystalline phase in the tested polymeric material.

Influence of Low Temperature Plasma Oxidizing on the Bioactivity of NiTi Shape Memory Alloy for Medical Applications.

The present study elucidates the impact of glow discharge oxidation within a low-temperature plasma environment on the bioactivity characteristics of an NiTi shape memory alloy. The properties of the produced surface layers, such as structure (TEM observations), surface morphology (SEM observations), chemical and phase composition (EDS and XRD measurements), wettability (optical gonimeter), and the biological response of osteoblasts and platelets to the oxidized surface compared with the NiTi alloy without a surface layer are presented. The presented surface modification of the NiTi shape memory alloy, achieved through oxidizing in a low-temperature plasma environment, led to the creation of a continuous surface layer composed of nanocrystalline titanium oxide TiO2 (rutile). The findings obtained from this study provide evidence that the oxidized layer augments the bioactivity of the shape memory alloy. This augmentation was substantiated through the spontaneous biomimetic deposition of apatite from a simulated body fluid (SBF) solution. Furthermore, the modified surface exhibited improved osteoblast proliferation, and enhanced platelet adhesion and activation. This proposed surface modification strategy holds promise as a prospective solution to enhance the biocompatibility and bioactivity of NiTi shape memory alloy intended for prolonged use in bone implant applications.

3D-printed wound dressings containing a fosmidomycin-derivative prevent Acinetobacter baumannii biofilm formation.

Acinetobacter baumannii causes a wide range of infections, including wound infections. Multidrug-resistant A. baumannii is a major healthcare concern and the development of novel treatments against these infections is needed. Fosmidomycin is a repurposed antimalarial drug targeting the non-mevalonate pathway, and several derivatives show activity toward A. baumannii. We evaluated the antimicrobial activity of CC366, a fosmidomycin prodrug, against a collection of A. baumannii strains, using various in vitro and in vivo models; emphasis was placed on the evaluation of its anti-biofilm activity. We also developed a 3D-printed wound dressing containing CC366, using melt electrowriting technology. Minimal inhibitory concentrations of CC366 ranged from 1 to 64 µg/mL, and CC366 showed good biofilm inhibitory and moderate biofilm eradicating activity in vitro. CC366 successfully eluted from a 3D-printed dressing, the dressings prevented the formation of A. baumannnii wound biofilms in vitro and reduced A. baumannii infection in an in vivo mouse model.

3D-printed dual drug delivery nanoparticle- loaded hydrogels to combat antibiotic-resistant bacteria.

Implant-associated infections are not easy to diagnose and very difficult to treat, due to the ability of major pathogens, such as Staphylococcus aureus, to develop biofilms and escape the immune response and antibiotic treatment. We, therefore, aimed to develop a 3D-printed dual rifampicin (Rif)- and vancomycin (Van)-loaded polylactic- co-glycolic acid (PLGA) nanoparticles (NPs) delivery system based on hydrogels made of gelatin methacrylate (GelMA). The release of Rif and Van from NPs manufactured from different PLGA molecular weights was studied in phosphate-buffered saline for 21 days. Low molecular weight PLGA NPs exhibited the fastest release of Rif and Van within the first 7 days and were selected for antimicrobial evaluation. Four different GelMA-based 3D-printed samples were successfully produced, carrying non-loaded NPs, Rif-NPs, Van-NPs, or alternating layers of Rif-NPs and Van-NP. The exposition of S. aureus against increased concentrations of Rif or Van produced new resistant strains to Rif (RifR) or Van (VanR). The GelMA hydrogel co-delivering Rif and Van eradicated S. aureus RN4220 RifR and RN4220 VanR strains. S. aureus RN4220 and S. aureus AMC 201 colonies developed resistance to Rif after contact with the GelMA hydrogel containing only Rif-NPs which appeared to be due to known mutations in the rpoB gene. In conclusion, 3D-printed GelMA hydrogel loaded with PLGA Rif-Van-NPs drug delivery system show promising in vitro results to prevent implant-associated infections caused by antimicrobial-resistant bacteria.

Toward osteomimetic formation of calcium phosphate coatings with carbonated hydroxyapatite.

Biomimetic production of coatings on various types of scaffolds is based mainly on simulated body fluid precipitation (SBF) of apatites, or, if the HCO3- is present, carbonated apatites. Recently, we proposed formation of calcium phosphates (CaP) precipitates by alkaline phosphatase (ALP) hydrolysing glycerophosphate in presence of calcium ions as an alternative to SBF. Since apatites synthesized in bone by the ALP activity contain carbonate anions, it was tempting to investigate whether the phosphatase method could be advanced into osteomimetic one. Therefore, taking example from the SBF studies, phosphatase incubation medium was enriched with carbonate ions at 4.2 and 27 mM concentration. X-ray diffraction of the precipitates disclosed peaks typical for hydroxyapatite (HAP). FTIR analysis showed that at both concentration of carbonate ions, apatites underwent both B and A substitution, more extensive at higher concentration. Thus, osteomimetic approach produced carbonated hydroxyapatites of the type encountered in bone tissue even at HCO3- concentration as low as 4.2 mM. Composite plates made of poly(ε-caprolactone) and mixture of ß-tricalcium phosphate and hydroxyapatite at mass ratio of 1:0.5:0.5, respectively, were covered by CaP coatings, i.e., CaP-0, CaP-4.2, CaP-27, by incubation in phosphatase medium containing 0, 4.2 or 27 mM of NaHCO3, respectively. Pristine or coated PCL50 plates were used to study release of calcium and adsorption/desorption of proteins, or seeded with human bone marrow mesenchymal stem cells (hMSC) for study of cell adhesion, spreading and osteogenic differentiation. Introduction of carbonate into the CaP coatings significantly increased release of Ca2+ in a carbonate concentration-dependent manner; the release was up to 4 times higher, when compared to CaP-0 coating, and reached 0.41 ± 0.01 mM for CaP-27 after first 24 h. Coating CaP-4.2 yielded significantly higher adsorption of bovine serum albumin and cytochrome C than CaP-0. All of the CaP coatings improved significantly hMSC adhesion, however, only CaP-4.2 provided 2 times higher cell number than PCL50 after 2 weeks of culture. Interestingly, ALP activity calculated per cell number was the highest on pristine plates, presumably because hMSC differentiate preferentially into osteoblasts at lower seeding densities. It appears, therefore, that the osteomimetic approach may be useful for production of carbonated hydroxyapatite coatings, but requires further studies and replacing intestinal phosphatase used in this work with one originating from bone.

Thermal Stability and Mechanical Behavior of Ultrafine-Grained Titanium with Different Impurity Content.

Ultrafine-grained (UFG) commercially pure (Ti Grade 2) and high-purity (Ti 99.99%) titanium can be a good alternative to less biocompatible Ti alloys in many biomedical applications. Their severe plastic deformation may lead to a substantial increase of strength, but their highly refined microstructure show a lower thermal stability which may limit their range of applications. The purpose of this study was to investigate the effect of interstitial elements on the thermal stability of UFG Ti Grade 2 and high-purity Ti 99.99% processed by a multi-pass cold rolling to the total thickness reduction of 90%. The severely cold rolled Ti sheets were annealed at temperature in the range of 100-600 °C for 1 h and, subsequently, they were evaluated in terms of microstructure stability, mechanical performance as well as heat effects measured by differential scanning calorimetry (DSC). It was found that the microstructure and mechanical properties were relatively stable up to 200 and 400 °C in the case of UFG Ti 99.99% and Ti Grade 2, respectively. DSC measurements confirmed the aforementioned results about lower temperature of recovery and recrystallization processes in the high-purity titanium. Surprisingly, the discontinuous yielding phenomenon occurred in both investigated materials after annealing above their thermal stability range, which was further discussed based on their microstructural characteristics. Additionally, the so-called hardening by annealing effect was observed within their thermal stability range (i.e., at 100-400 °C for UFG Ti Grade 2 and 100 °C for UFG Ti 99.99%).

Long-Term In Vitro Assessment of Biodegradable Radiopaque Composites for Fiducial Marker Fabrication.

Biodegradable polymer-based composite materials may be successfully utilised to fabricate fiducial markers (FMs), which are intended to precisely label tumour margins during image-guided surgery or radiotherapy. However, due to matrix degradability, the stability of the functional properties of FMs depends on the chosen polymer. Thus, this study aimed to investigate novel radiopaque composites which varied in the polymeric matrix-polycaprolactone (PCL), poly(L-lactide-co-caprolactone) (P[LAcoCL]) with two molar ratios (70:30 and 85:15), and poly(L-lactide-co-glycolide) (with molar ratio 82:18). The radiopaque component of the materials was a mixture of barium sulphate and hydroxyapatite. The changes in water contact angle, stiffness, and radiopacity occurring during the 24-week-long degradation experiment were examined for the first time. This study comprehensively analyses the microstructural causes of composites behaviour within degradation experiments using thermogravimetric analysis (TGA), differential scanning calorimetry (DSC), gel permitted chromatography (GPC), and scanning electron microscopy (SEM). The obtained results suggest that the utilized biodegradable matrix plays an essential role in radiopaque composite properties and stability thereof. This long-term in vitro assessment enabled a comparison of the materials and aided in choosing the most favourable composite for FMs' fabrication.

A Niclosamide-releasing hot-melt extruded catheter prevents Staphylococcus aureus experimental biomaterial-associated infection.

Biomaterial-associated infections are a major healthcare challenge as they are responsible for high disease burden in critically ill patients. In this study, we have developed drug-eluting antibacterial catheters to prevent catheter-related infections. Niclosamide (NIC), originally an antiparasitic drug, was incorporated into the polymeric matrix of thermoplastic polyurethane (TPU) via solvent casting, and catheters were fabricated using hot-melt extrusion technology. The mechanical and physicochemical properties of TPU polymers loaded with NIC were studied. NIC was released in a sustained manner from the catheters and exhibited in vitro antibacterial activity against Staphylococcus aureus and Staphylococcus epidermidis. Moreover, the antibacterial efficacy of NIC-loaded catheters was validated in an in vivo biomaterial-associated infection model using a methicillin-susceptible and methicillin-resistant strain of S. aureus. The released NIC from the produced catheters reduced bacterial colonization of the catheter as well as of the surrounding tissue. In summary, the NIC-releasing hot-melt extruded catheters prevented implant colonization and reduced the bacterial colonization of peri-catheter tissue by methicillin sensitive as well as resistant S. aureus in a biomaterial-associated infection mouse model and has good prospects for preclinical development.

The Utility of Recycled Rice Husk-Reinforced PVC Composite Profiles for Façade Cladding.

The production process of construction profiles from natural fibre-reinforced polymer composites, as well as their assembly, generates considerable amounts of waste. The study analysed the possibility of utilising the said waste to produce profiles with the same intended use as products made from the primary material. The analysis involved the recycling of rice husk-reinforced PVC profiles. As a result of the applied post-processing, a composite of higher homogeneity and better filler dispersion than the product made of primary material was obtained. A slight improvement in thermal properties was observed. From the DSC test, Tg values of 78 °C and nearly 80 °C were obtained, while from the TGA test, mass loss values of 0.6% and 0.4% and the decomposition temperatures of 211 °C and 217 °C were noted for profiles of primary and secondary material, respectively. A softening temperature of 75 °C was obtained for primary material profiles, while nearly 77 °C was obtained for secondary. The more favourable mechanical properties of recycled profiles were also maintained. The higher value of flexural strength, flexural modulus, impact strength and hardness by 31%, 24%, 48% and 40% were obtained, respectively. After hydrothermal cycling, the same properties were higher for secondary material profiles by 35%, 20%, 68%, and 67%, respectively. The recorded level of performance properties of recycled products, better than those of primary material standard construction products', allows us to conclude that profiles made of waste are useful for façade claddings.

Biodegradable Fiducial Markers for Bimodal Near-Infrared Fluorescence- and X-ray-Based Imaging.

This study aimed to evaluate, for the first time, implantable, biodegradable fiducial markers (FMs), which were designed for bimodal, near-infrared fluorescence-based (NIRF) and X-ray-based imaging. The developed FMs had poly(l-lactide-co-caprolactone)-based core-shell structures made of radiopaque (core) and fluorescent (shell) composites with a poly(l-lactide-co-caprolactone) matrix. The approved for human use contrast agents were utilized as fillers. Indocyanine green was applied to the shell material, whereas in the core materials, iohexol and barium sulfate were compared. Moreover, the possibility of tailoring the stability of the properties of the core materials by the addition of hydroxyapatite (HAp) was examined. The performed in situ (porcine tissue) and in vivo experiment (rat model) confirmed that the developed FMs possessed pronounced contrasting properties in NIRF and X-ray imaging. The presence of HAp improved the radiopacity of FMs at the initial state. It was also proved that, in iohexol-containing FMs, the presence of HAp slightly decreased the stability of contrasting properties, while in BaSO4-containing ones, changes were less pronounced. A comprehensive material analysis explaining the differences in the stability of the contrasting properties was also presented. The tissue response around the FMs with composite cores was comparable to that of the FMs with a pristine polymeric core. The developed composite FMs did not cause serious adverse effects on the surrounding tissues even when irradiated in vivo. The developed FMs ensured good visibility for NIRF image-supported tumor surgery and the following X-ray image-guided radiotherapy. Moreover, this study replenishes a scanty report regarding similar biodegradable composite materials with a high potential for application.

Biological and Corrosion Evaluation of In Situ Alloyed NiTi Fabricated through Laser Powder Bed Fusion (LPBF).

In this work, NiTi alloy parts were fabricated using laser powder bed fusion (LBPF) from pre-alloyed NiTi powder and in situ alloyed pure Ni and Ti powders. Comparative research on the corrosive and biological properties of both studied materials was performed. Electrochemical corrosion tests were carried out in phosphate buffered saline at 37 °C, and the degradation rate of the materials was described based on Ni ion release measurements. Cytotoxicity, bacterial growth, and adhesion to the surface of the fabricated coupons were evaluated using L929 cells and spherical Escherichia coli (E. coli) bacteria, respectively. The in situ alloyed NiTi parts exhibit slightly lower corrosion resistance in phosphate buffered saline solution than pre-alloyed NiTi. Moreover, the passive layer formed on in situ alloyed NiTi is weaker than the one formed on the NiTi fabricated from pre-alloyed NiTi powder. Furthermore, in situ alloyed NiTi and NiTi made from pre-alloyed powders have comparable cytotoxicity and biological properties. Overall, the research has shown that nitinol sintered using in situ alloyed pure Ni and Ti is potentially useful for biomedical applications.

Optical and structural properties of europium doped Y-Al-O compounds grown by microwave driven hydrothermal technique.

Perovskites, garnets, monoclinic forms, and lately also oxyhydroxides doped with rare-earth ions have been drawn large attention due to their beneficial optical and photovoltaic properties. In this work, we have shown that several forms of crystals from Y-Al-O family can be synthesized using microwave driven hydrothermal technique using different pH and post-growth annealing at different temperatures. The structural and optical properties of these crystals were investigated as a function of hydrothermal crystallization conditions. For this purpose, x-ray diffraction, scanning electron microscopy, energy-dispersive x-ray spectroscopy, transmission electron microscopy, photoluminescence, and photoluminescence excitation studies were performed. All the structures have been doped with Eu3+ions which are known as a local symmetry sensor because various symmetries generate different crystal fields and thus affect their luminescence spectra. The optical properties of the obtained nanoparticles in correlation with their structure and chemical composition are discussed.

Plasma Modification of Carbon Coating Produced by RF CVD on Oxidized NiTi Shape Memory Alloy under Glow-Discharge Conditions.

Our previous work has shown that for cardiac applications, combining low-temperature plasma oxidation with an amorphous carbon coating (a-C:N:H type) constitutes a prospective solution. In this study, a short-term modification by low-temperature oxygen plasma is proposed as an example and a method for shaping the topography and surface energy of the outer amorphous carbon coating, produced via the Radio-Frequency Chemical Vapour Deposition (RFCVD) method on NiTi alloy oxidized under glow-discharge conditions. This treatment alters the chemical composition of the outer zone of the surface layer. A slight increase is also noted in the surface roughness at the nanoscale. The contact angles were shown to increase by about 20% for water and 30% for diiodomethane, while the surface free energy decreased by ca. 11%. The obtained results indicate that even short-term contact with low-temperature plasma can shape the surface properties of the carbon coating, an outcome which shows potential in terms of its use in medical applications.

Coupling Additive Manufacturing with Hot Melt Extrusion Technologies to Validate a Ventilator-Associated Pneumonia Mouse Model.

Additive manufacturing is widely used to produce highly complex structures. Moreover, this technology has proven its superiority in producing tools which can be used in different applications. We designed and produced an extrusion nozzle that allowed us to hot melt extrude drug-loaded tubes. The tubes were an essential part of a new mouse ventilator-associated pneumonia (VAP) model. Ciprofloxacin (CPX) was selected for its expected activity against the pathogen Staphylococcus aureus and ease of incorporation into thermoplastic polyurethane (TPU). TPU was selected as the carrier polymer for its biocompatibility and use in a variety of medical devices such as tubing and catheters. The effect of loading CPX within the TPU polymeric matrix and the physicochemical properties of the produced tubes were investigated. CPX showed good thermal stability and in vitro activity in preventing S. aureus biofilm formation after loading within the tube's polymeric matrix. Moreover, the produced tubes showed anti-infective efficacy in vivo. The produced tubes, which were extruded via our novel nozzle, were vital for the validation of our mouse VAP model. This model can be adopted to investigate other antibacterial and antibiofilm compounds incorporated in polymeric tubes using hot melt extrusion.

Water vapor induced self-assembly of islands/honeycomb structure by secondary phase separation in polystyrene solution with bimodal molecular weight distribution.

The formation of complex structures in thin films is of interest in many fields. Segregation of polymer chains of different molecular weights is a well-known process. However, here, polystyrene with bimodal molecular weight distribution, but no additional chemical modification was used. It was proven that at certain conditions, the phase separation occurred between two fractions of bimodal polystyrene/methyl ethyl ketone solution. The films were prepared by spin-coating, and the segregation between polystyrene phases was investigated by force spectroscopy. Next, water vapour induced secondary phase separation was investigated. The introduction of moist airflow induced the self-assembly of the lower molecular weight into islands and the heavier fraction into a honeycomb. As a result, an easy, fast, and effective method of obtaining island/honeycomb morphologies was demonstrated. The possible mechanisms of the formation of such structures were discussed.

From Matrix Vesicles to Miniature Rocks: Evolution of Calcium Deposits in Calf Costochondral Junctions.

OBJECTIVE: Initial stages of cartilage matrix calcification depend on the activity of matrix vesicles. The purpose of the study was to describe how calcified matrix vesicles join into larger structures, to present their up-to-date undescribed 3-dimensional image, and to observe how calcified matrix relates to chondrocyte lacunae. DESIGN: Calcified cartilage was obtained from the zone of provisional calcification of calf costochondral junctions, then enzymatically isolated and studied by microtomography, scanning electron microscopy, atomic force microscopy and X-ray diffraction, and Fourier transform infrared spectroscopy. RESULTS: Hyaluronidase digestion released packets of granules surrounded by the cartilage matrix. Further digestion, with collagenase and trypsin, removed matrix and exposed granules with dimensions within 50 to 150 nm range, which we consider as equivalent of calcified matrix vesicles. Granules joined into larger groups with dimensions of 0.5 to 2 µm, which we call globular units. Certain matrix vesicles appeared well connected but contained globular units that had spaces filled with electron lucent material, presumably matrix or chondrocyte remnants. Globular units were organized into massive structures taking the shape of oval plates. Comparison of these plates with lacunae containing isogenous groups of chondrocytes from proliferative zone of costochondral junction suggests that the cells from a single lacuna were responsible for the formation of one plate. The plates were connected with each other and extended over provisional calcification zone. CONCLUSIONS: The outcome showed how particular calcified matrix vesicles associate into globular units, which organize into massive structures assuming the shape of oval plates and eventually cover large areas of cartilage matrix.

The effect of diameter of fibre on formation of hydrogen bonds and mechanical properties of 3D-printed PCL.

Fused Deposition Modelling (FDM) technique has been widely utilized in fabrication of 3D porous scaffolds for tissue engineering (TE) applications. Surprisingly, although there are many publications devoted to the architectural features of the 3D scaffolds fabricated by the FDM, none of them give us evident information about the impact of the diameter of the fibres on material properties. Therefore, the aim of this study was to investigate, for the first time, the effect of the diameter of 3D-printed PCL fibres on variations in their microstructure and resulting mechanical behaviour. The fibres made of poly(ε-caprolactone) (PCL) were extruded through commonly used types of nozzles (inner diameter ranging from 0.18 mm to 1.07 mm) by means of FDM technique. Static tensile test and atomic force microscopy working in force spectroscopy mode revealed strong decrease in the Young's modulus and yield strength with increasing fibre diameter in the investigated range. To explain this phenomenon, we conducted differential scanning calorimetry, wide-angle X-ray-scattering, Fourier-transform infrared spectroscopy, infrared and polarized light microscopy imaging. The obtained results clearly showed that the most prominent effect on the obtained microstructures and mechanical properties had different cooling and shear rates during fabrication process causing changes in supramolecular interactions of PCL. The observed fibre size-dependent formation of hydrogen bonds affected the crystalline structure and its stability. Summarising, this study clearly demonstrates that the diameter of 3D-printed fibres has a strong effect on obtained microstructure and mechanical properties, therefore should be taken into consideration during design of the 3D TE scaffolds.

3D-Printed Drug Delivery Systems: The Effects of Drug Incorporation Methods on Their Release and Antibacterial Efficiency.

Additive manufacturing technologies have been widely used in the medical field. More specifically, fused filament fabrication (FFF) 3D-printing technology has been thoroughly investigated to produce drug delivery systems. Recently, few researchers have explored the possibility of directly 3D printing such systems without the need for producing a filament which is usually the feedstock material for the printer. This was possible via direct feeding of a mixture consisting of the carrier polymer and the required drug. However, as this direct feeding approach shows limited homogenizing abilities, it is vital to investigate the effect of the pre-mixing step on the quality of the 3D printed products. Our study investigates the two commonly used mixing approaches-solvent casting and powder mixing. For this purpose, polycaprolactone (PCL) was used as the main polymer under investigation and gentamicin sulfate (GS) was selected as a reference. The produced systems' efficacy was investigated for bacterial and biofilm prevention. Our data show that the solvent casting approach offers improved drug distribution within the polymeric matrix, as was observed from micro-computed topography and scanning electron microscopy visualization. Moreover, this approach shows a higher drug release rate and thus improved antibacterial efficacy. However, there were no differences among the tested approaches in terms of thermal and mechanical properties.