A plasma-based pressure pulse generator for simulating pellet-cladding mechanical interaction during reactivity-initiated accident.

This paper describes the characteristics of a plasma-based pressure pulse generator and its potential use as a simulator for studying pellet-cladding mechanical interaction (PCMI) during reactivity-initiated accidents (RIAs). In this device, a transient pressure pulse is generated by rapid heating and expansion of hot, dense plasma inside a nuclear fuel cladding. Thus, the parameters of a pressure pulse, such as peak pressure and pressure rise-rate, can be controlled by modifying the electrical parameters of a pulse discharge circuit. The pulse discharge circuit utilizes a capacitor bank comprising several energy storage capacitors connected in parallel and a high-power solid-state switch. A pressure loading system is attached as a load to the pulse discharge circuit. The power and energy delivered to the load are calculated by measuring the voltage and current waveforms at one end of the loading system. A piezoelectric sensor is connected at the other end of the loading system to simultaneously measure the pressure pulse inside the cladding tube. Preliminary experiments are carried out with a stainless-steel tube to characterize the performance of the device as well as with a pre-hydrided ZIRLO™ cladding tube to demonstrate the potential of the device as a simulator for studying the failure characteristics of the cladding as a result of an RIA. The high pressurization rate of the device is expected to offer unique advantages for studying the PCMI mechanism.

High-magnetic-confinement mode in partially magnetized E×B plasmas.

The suppression of the gradient-drift driven instability and the transition to the high-magnetic-confinement mode are experimentally observed in a cylindrical partially magnetized E×B plasma using an additional biasable electrode installed at the radial edge. When a positive voltage is applied to the electrode, an electron-loss channel forms in its direction, breaking the spatially symmetric nonambipolar flow. Finally, in the steady state, the plasma density tends to peak in the plasma core, approaching plasma densities that are four times larger than those observed in the case where the instability is the strongest. A high-magnetic-confinement mode with a reduced edge-to-center density ratio of 0.16 is observed, which demonstrates that the saturation of magnetic confinement due to the gradient-drift driven instability can be prevented by an asymmetric nonambipolar flow.

Exploring the nonextensive thermodynamics of partially ionized gas in magnetic field.

Contrary to classical thermodynamics, which deals with systems in thermal equilibrium, partially ionized gases generally do not reach thermal equilibrium. Nonextensive statistical mechanics has helped extend classical thermodynamics to nonequilibrium ionized gas. However, the fundamental question on whether the statistics of non-Maxwellian electrons satisfy the laws of thermodynamics has not been resolved. Here, we verify the thermodynamic laws of reversible and adiabatic processes for a magnetically expanding ionized gas. Together with the experimental evidence of the non-Maxwellian electron distribution, the κ distribution, which measures the thermal equilibrium states, shows the Tsallis entropy to be nearly constant and the polytropic index to be close to adiabatic values along a divergent magnetic field. These results verify that the collisionless magnetic expansion of a nonequilibrium plasma is reversible and adiabatic, and an isentropic process is the origin of the high-energy tail of the energy distribution far downstream.

Development of a filtered AXUV diode array for X-pinch soft x-ray spectra in the energy range of 1-10 keV.

We develop a filtered absolute extreme ultraviolet (AXUV) diode array to measure the time evolution of the soft x-ray spectrum in the energy range of 1-10 keV. AXUV-HS5, the detector, has a fast rise time of 0.7 ns, a wide energy detection range, and high accessibility. We use Geant4 simulations to design an appropriate filter set for flat-and-sharp virtual channels (VCs), where a filter with no spectral edge removes large tails of the response curves. A Levenberg-Marquardt (LM) method, sensitive to the expected spectral function, is improved to reliably generate a continuous radiation spectrum, by utilizing spectral information from the least-squares (LS) method that reconstructs a discrete spectrum with low spectral resolution directly from the VCs. We test the filtered AXUV diode array on an X-pinch device with a peak current of 140 kA at Seoul National University; the array with ten channels is installed in a vacuum chamber. For a two-wire 40 µm stainless steel X-pinch, x-ray power, radiation temperature, and the reconstructed x-ray spectrum are obtained from the filtered AXUV diode array by the combined LS-LM method.

A modular X-pinch device for versatile X-pinch experiments at Seoul National University.

This paper describes an X-pinch device recently developed at Seoul National University (SNU). The SNU X-pinch device is designed and fabricated to accommodate various diagnostics as well as conduct versatile experiments. It is easy to change the capacitance of the pulse generator because the capacitor bank has a modular design without insulation oil or gas. This allows us to perform a variety of experiments with a wide capacitance range from 80 to 800 nF. The operating voltage of the SNU X-pinch device is controlled from 20 to 100 kV by adjusting the gas pressure inside a triggered spark-gap switch. Triggering of the spark-gap switch is synchronized with the operation of a pulsed laser to diagnose the X-pinch plasma at the proper time. A large vacuum chamber precisely machined from an aluminum mono-block is attached to the top of the pulse generator. It is designed to accommodate not only various X-pinch loads but also various diagnostic apparatus such as optical components. Initial experiments with the SNU X-pinch device have successfully generated x rays with wires of various materials and sizes. The device will be used not only to explore the dynamics of X-pinch plasmas but also as a test stand for diagnostics of high-energy-density plasmas.

Data analysis scheme for correcting general misalignments of an optics configuration for a voltage measurement system based on the Pockels electro-optic effect.

Having a sub-ns response time and not requiring physical contacts to the measurement points, a voltage measurement system based on the Pockels electro-optic effect, referred to as a PE (Pockels effect)-based voltmeter, is widely used for pulsed high voltage devices such as accelerators and X-pinch systems. To correct for the misalignment of a Pockels cell and the transmittance ratio of a beam splitter, a polar-coordinate-based data analysis scheme has been proposed. This scheme also overcomes a limitation on the measurable range of a PE-based voltmeter without ambiguity and can measure the half-wave voltage of a Pockels cell. We present an improved polar-coordinate-based data analysis scheme using an ellipse fitting method, which can correct for misalignments of all the optics components of a PE-based voltmeter while keeping the advantages of the previous scheme. We show the results of the improved data analysis scheme for measuring a slowly modulated voltage up to approximately 5 kV in about 30 s and a pulsed high voltage up to 7 kV with a rise time of less than 20 ns.

Improved gating device of time-of-flight ion mass analyzer for ion sources.

A gating device is a critical component in a time-of-flight (TOF) ion mass analyzer for identifying ion species extracted from ion sources according to their mass-to-charge ratio. It consists of several concentric ring electrodes to deflect as many ions as possible within a very short gate time, thus increasing the ion current collected in a Faraday cup. In this study, we further improve the ion collection efficiency of the gating device by minimizing potential distortion along the paths of ions, by modifying the structure of gate electrodes and applying a bipolar gate pulse on them. Using the improved gating device, we find that the ion beam current increased by nearly 50% compared to the conventional one without changing the noise level. The improved TOF system is well applied to identify the spectrum of ion species extracted from a cold cathode Penning ion source, depending on the operating conditions.

Initial operation results of NE213 scintillation detector for time-resolved measurements on triton burnup in KSTAR.

In time-resolved measurement for triton burnup in Korea Superconducting Tokamak Advanced Research (KSTAR) deuterium plasmas, an NE213 liquid scintillation detector was installed and operated during the 2017 KSTAR campaign. The detector is composed of an NE213 scintillator (50 mm in diameter and 10 mm in thickness) and a photomultiplier tube (PMT). The PMT anode signal was processed under a data acquisition system which contains a field programmable gate array circuit and pulse processing software that is capable of discriminating gamma-ray and neutron pulse signals. In order to determine an appropriate threshold level for the 14 MeV neutron signal resulting from triton burnup, the NE213 scintillation detector was calibrated by using d-d and d-t neutron generators at the National Fusion Research Institute and Intense 14 MeV Neutron Source Facility, OKTAVIAN, Osaka University, Japan. The detector was installed on KSTAR with a 10 mm thick soft-iron stray magnetic field shield and a radiation shield which consists of 100 mm thick lead blocks and 200 mm thick borated polyethylene blocks. A discrimination range for d-t neutron was determined based on test results from neutron generators and KSTAR. Data points selected from the discrimination range were consistent with the classical triton confinement characteristics. In conclusion, under condition of an input counting rate of 1.9 × 105 counts per second (CPS), the detector is able to measure triton burnup signals up to 500 CPS for various plasma parameters.

Characterization of photo-multiplier tube as ex-vessel radiation detector in tokamak.

Feasibility of using conventional photo-multiplier tubes (PMTs) without a scintillator as an ex-vessel radiation detector in a tokamak environment is studied. Basic irradiation tests using standard gamma ray sources and a d-d neutron generator showed that the PMT is responding both to gamma photons and neutrons, possibly due to the direct generation of secondary electrons inside the PMT by the impingement of high energy photons. Because of the selective sensitivity of the PMT to hard x-ray and neutrons in ohmic and neutral beam injected plasmas, respectively, it is shown that the PMT with certain configuration can be utilized either to monitor the fluctuation in the fusion neutron generation rate or to study the behavior of runaway electrons in tokamaks.

Electron density profile measurements from hydrogen line intensity ratio method in Versatile Experiment Spherical Torus.

Electron density profiles of versatile experiment spherical torus plasmas are measured by using a hydrogen line intensity ratio method. A fast-frame visible camera with appropriate bandpass filters is used to detect images of Balmer line intensities. The unique optical system makes it possible to take images of Hα and Hß radiation simultaneously, with only one camera. The frame rate is 1000 fps and the spatial resolution of the system is about 0.5 cm. One-dimensional local emissivity profiles have been obtained from the toroidal line of sight with viewing dumps. An initial result for the electron density profile is presented and is in reasonable agreement with values measured by a triple Langmuir probe.

Triton burnup measurements in KSTAR using a neutron activation system.

Measurements of the time-integrated triton burnup for deuterium plasma in Korea Superconducting Tokamak Advanced Research (KSTAR) have been performed following the simultaneous detection of the d-d and d-t neutrons. The d-d neutrons were measured using a 3He proportional counter, fission chamber, and activated indium sample, whereas the d-t neutrons were detected using activated silicon and copper samples. The triton burnup ratio from KSTAR discharges is found to be in the range 0.01%-0.50% depending on the plasma conditions. The measured burnup ratio is compared with the prompt loss fraction of tritons calculated with the Lorentz orbit code and the classical slowing-down time. The burnup ratio is found to increase as plasma current and classical slowing-down time increase.

A simple spectroscopic method to determine the degree of dissociation in hydrogen plasmas with wide-range spectrometer.

A new and simple method for determining the degree of dissociation in hydrogen plasmas is presented. In this method, wide-range spectrum covering from an atomic H-γ line (434.05 nm) to molecular Fulcher-α band (600-640 nm) is measured simultaneously by a wide-range miniature spectrometer. Since the wide-range spectrum measured by the miniature spectrometer is too broadened to resolve respective lines in the Fulcher-α band, a synthetic spectrum method is applied to improve the accuracy in the Q-branch of Fulcher-α band intensity measurement. In order to reduce the influence from other transitions or anomalous P- and R-branch of Fulcher-α spectrum, the Fulcher-α spectra of which vibrational states are higher than 1 (υ ≥ 1) are synthesized using the rotational temperature obtained by the 0-0 Fulcher-α spectrum. The degree of dissociation is determined from the intensity ratio between H-γ line and the synthesized Fulcher-α band spectrum. A comparative study carried out in a volume-produced negative hydrogen ion source shows that the degree of dissociation determined by this method agrees well with the measured values using a spectrometer with high spectral resolution. The present method is expected to be useful to characterize the plasma sources with molecular species since it provides important parameters for understanding neutral particle behaviors.

Electron cyclotron resonance heating by magnetic filter field in a negative hydrogen ion source.

The influence of magnetic filter field on plasma properties in the heating region has been investigated in a planar-type inductively coupled radio-frequency (RF) H(-) ion source. Besides filtering high energy electrons near the extraction region, the magnetic filter field is clearly observed to increase the electron temperature in the heating region at low pressure discharge. With increasing the operating pressure, enhancement of electron temperature in the heating region is reduced. The possibility of electron cyclotron resonance (ECR) heating in the heating region due to stray magnetic field generated by a filter magnet located at the extraction region is examined. It is found that ECR heating by RF wave field in the discharge region, where the strength of an axial magnetic field is approximately ∼4.8 G, can effectively heat low energy electrons. Depletion of low energy electrons in the electron energy distribution function measured at the heating region supports the occurrence of ECR heating. The present study suggests that addition of axial magnetic field as small as several G by an external electromagnet or permanent magnets can greatly increase the generation of highly ro-vibrationally excited hydrogen molecules in the heating region, thus improving the performance of H(-) ion generation in volume-produced negative hydrogen ion sources.

Optimization of plasma parameters with magnetic filter field and pressure to maximize H⁻ ion density in a negative hydrogen ion source.

Transverse magnetic filter field as well as operating pressure is considered to be an important control knob to enhance negative hydrogen ion production via plasma parameter optimization in volume-produced negative hydrogen ion sources. Stronger filter field to reduce electron temperature sufficiently in the extraction region is favorable, but generally known to be limited by electron density drop near the extraction region. In this study, unexpected electron density increase instead of density drop is observed in front of the extraction region when the applied transverse filter field increases monotonically toward the extraction aperture. Measurements of plasma parameters with a movable Langmuir probe indicate that the increased electron density may be caused by low energy electron accumulation in the filter region decreasing perpendicular diffusion coefficients across the increasing filter field. Negative hydrogen ion populations are estimated from the measured profiles of electron temperatures and densities and confirmed to be consistent with laser photo-detachment measurements of the H(-) populations for various filter field strengths and pressures. Enhanced H(-) population near the extraction region due to the increased low energy electrons in the filter region may be utilized to increase negative hydrogen beam currents by moving the extraction position accordingly. This new finding can be used to design efficient H(-) sources with an optimal filtering system by maximizing high energy electron filtering while keeping low energy electrons available in the extraction region.

Operating conditions for the generation of stable anode spot plasma in front of a positively biased electrode.

Stability of an anode spot plasma, which is an additional high density plasma generated in front of a positively biased electrode immersed in ambient plasma, is a critical issue for its utilization to various types of ion sources. In this study, operating conditions for the generation of stable anode spot plasmas are experimentally investigated. Diagnostics of the bias current flowing into the positively biased electrode and the properties of ambient plasma reveal that unstable nature of the anode spot is deeply associated with the reduction of double layer potential between the anode spot plasma and the ambient plasma. It is found that stability of the anode spot plasma can be improved with increasing the ionization rate in ambient plasma so as to compensate the loss of electrons across the double layer or with enlarging the area of the biased electrode to prevent electron accumulation inside the anode spot. The results obtained from the present study give the guideline for operating conditions of anode spot plasmas as an ion source with high brightness.

Effects of discharge chamber length on the negative ion generation in volume-produced negative hydrogen ion source.

In a volume-produced negative hydrogen ion source, control of electron temperature is essential due to its close correlation with the generation of highly vibrationally excited hydrogen molecules in the heating region as well as the generation of negative hydrogen ions by dissociative attachment in the extraction region. In this study, geometric effects of the cylindrical discharge chamber on negative ion generation via electron temperature changes are investigated in two discharge chambers with different lengths of 7.5 cm and 11 cm. Measurements with a radio-frequency-compensated Langmuir probe show that the electron temperature in the heating region is significantly increased by reducing the length of the discharge chamber due to the reduced effective plasma size. A particle balance model which is modified to consider the effects of discharge chamber configuration on the plasma parameters explains the variation of the electron temperature with the chamber geometry and gas pressure quite well. Accordingly, H(-) ion density measurement with laser photo-detachment in the short chamber shows a few times increase compared to the longer one at the same heating power depending on gas pressure. However, the increase drops significantly as operating gas pressure decreases, indicating increased electron temperatures in the extraction region degrade dissociative attachment significantly especially in the low pressure regime. It is concluded that the increase of electron temperature by adjusting the discharge chamber geometry is efficient to increase H(-) ion production as long as low electron temperatures are maintained in the extraction region in volume-produced negative hydrogen ion sources.

Development of a radio frequency ion source with multi-helicon plasma injectors for neutral beam injection system of Versatile Experiment Spherical Torus.

Despite of high plasma density, helicon plasma has not yet been applied to a large area ion source such as a driver for neutral beam injection (NBI) system due to intrinsically poor plasma uniformity in the discharge region. In this study, a radio-frequency (RF) ion source with multi-helicon plasma injectors for high plasma density with good uniformity has been designed and constructed for the NBI system of Versatile Experiment Spherical Torus at Seoul National University. The ion source consists of a rectangular plasma expansion chamber (120 × 120 × 120 mm(3)), four helicon plasma injectors with annular permanent magnets and RF power system. Main feature of the source is downstream plasma confinement in the cusp magnetic field configuration which is generated by arranging polarities of permanent magnets in the helicon plasma injectors. In this paper, detailed design of the multi-helicon plasma injector and plasma characteristics of the ion source are presented.

Investigation of helium ion production in constricted direct current plasma ion source with layered-glows.

Generation of helium ions is experimentally investigated with a constricted direct current (DC) plasma ion source operated at layered-glow mode, in which electrons could be accelerated through multiple potential structures so as to generate helium ions including He(2+) by successive ionization collisions in front of an extraction aperture. The helium discharge is sustained with the formation of a couple of stable layers and the plasma ball with high density is created near the extraction aperture at the operational pressure down to 0.6 Torr with concave cathodes. The ion beam current extracted with an extraction voltage of 5 kV is observed to be proportional to the discharge current and inversely proportional to the operating pressure, showing high current density of 130 mA/cm(2) and power density of 0.52 mA/cm(2)/W. He(2+) ions, which were predicted to be able to exist due to multiple-layer potential structure, are not observed. Simple calculation on production of He(2+) ions inside the plasma ball reveals that reduced operating pressure and increased cathode area will help to generate He(2+) ions with the layered-glow DC discharge.

Design of a dual sensor probe array for internal field measurement in Versatile Experiment Spherical Torus.

A dual sensor probe array is designed and constructed for internal magnetic field measurement at Versatile Experiment Spherical Torus (VEST) at the Seoul National University. Simultaneous use of Hall sensors and chip inductors allows cross-calibration among the measurements and compensation for each other's weaknesses while their small sizes are expected to cause only mild plasma perturbations. Calibration of the dual sensor probe array, using a Helmholtz coil, shows good sensitivity for the magnetic field measurement of the VEST. Prior to Ohmic start-up, the magnetic field structure inside the vacuum chamber is measured by using the calibrated probe array. The dual sensor probe array is expected to be useful in analyzing the temporal magnetic field structure change during the magnetic reconnection and in reconstruction of the current profile during the discharge of the VEST device.