Improved sensitivity in paper-based microfluidic analytical devices using a pH-responsive valve for nitrate analysis.

This paper presents an innovative application of chitosan material to be used as pH-responsive valves for the precise control of lateral flow in microfluidic paper-based analytical devices (µPADs). The fabrication of µPADs involved wax printing, while pH-responsive valves were created using a solution of chitosan in acetic acid. The valve-forming solution was applied, and ready when dry; by exposure to acidic solutions, the valve opens. Remarkably, the valves exhibited excellent compatibility with alkaline, neutral, and acidic solutions with a pH higher than 4. The valve opening process had no impact on the flow rate and colorimetric analysis. The potential of chitosan valves used for flow control was demonstrated for µPADs employed for nitrate determination. Valves were used to increase the conversion time of nitrate to nitrite, which was further analyzed using the Griess reaction. The µPAD showed a linear response in the concentration range of 10-100 µmol L-1, with a detection limit of 5.4 µmol L-1. As a proof of concept, the assay was successfully applied to detect nitrate levels in water samples from artificial lakes of recreational parks. For analyses that require controlled kinetics and involve multiple sequential steps, the use of chitosan pH-responsive valves in µPADs is extremely valuable. This breakthrough holds great potential for the development of simple and high-impact microfluidic platforms that can cater to a wide range of analytical chemistry applications.

A review of the recent achievements and future trends on 3D printed microfluidic devices for bioanalytical applications.

3D printing has revolutionized the manufacturing process of microanalytical devices by enabling the automated production of customized objects. This technology promises to become a fundamental tool, accelerating investigations in critical areas of health, food, and environmental sciences. This microfabrication technology can be easily disseminated among users to produce further and provide analytical data to an interconnected network towards the Internet of Things, as 3D printers enable automated, reproducible, low-cost, and easy fabrication of microanalytical devices in a single step. New functional materials are being investigated for one-step fabrication of highly complex 3D printed parts using photocurable resins. However, they are not yet widely used to fabricate microfluidic devices. This is likely the critical step towards easy and automated fabrication of sophisticated, complex, and functional 3D-printed microchips. Accordingly, this review covers recent advances in the development of 3D-printed microfluidic devices for point-of-care (POC) or bioanalytical applications such as nucleic acid amplification assays, immunoassays, cell and biomarker analysis and organs-on-a-chip. Finally, we discuss the future implications of this technology and highlight the challenges in researching and developing appropriate materials and manufacturing techniques to enable the production of 3D-printed microfluidic analytical devices in a single step.

Digitally Controlled Printing of Bioink Barriers for Paper-Based Analytical Devices: An Environmentally Friendly One-Step Approach.

The patterning of hydrophilic paper with hydrophobic materials has emerged as an interesting method for the fabrication of paper-based devices (PADs). Herein, we demonstrate a digitally automated, easy, low-cost, eco-friendly, and readily available method to create highly hydrophobic barriers on paper that can be promptly employed with PADs by simply using a bioink made with rosin, a commercially available natural resin obtained from conifer trees. The bioink can be easily delivered with the use of a ballpoint pen to produce water- and organic solvent-resistant barriers, showing superior properties when compared to other methods such as wax-printing or permanent markers. The approach enables the pen to be attached to a commercially available cutting printer to perform the semiautomated fabrication of hydrophobic barriers for PADs. With the aid of digitally controlled optimization, together with features of machine learning and design of experiments, we show a thorough investigation on the barrier strength that can be further adjusted to the desired application's needs. Then, we explored the barrier sturdiness across various uses, such as wide range aqueous pH sensing and the harsh acidic/organic conditions needed for the colorimetric detection of cholecalciferol.

Fabrication of paper-based analytical devices using stencil-printed glass varnish barriers for colorimetric detection of salivary α-amylase.

BACKGROUND: Developing disposable paper-based devices has positively impacted analytical science, particularly in developing countries. Some benefits of those devices include their versatility, affordability, environmentally friendly, and the possibility of being integrated with portable electrochemical or colorimetric detectors. Paper-based analytical devices (PADs) comprising circular zones and microfluidic networks have been successfully employed in the analytical chemistry reign. However, the combination of the stencil-printing method and alternative binder has not been satisfactorily explored for fabricating colorimetric paper devices. RESULTS: We developed PADs exploring the stencil printing approach and glass varnish as the hydrophobic chemical agent. As a proof-of-concept, the colorimetric assay of salivary α-amylase (sAA) was performed in saliva samples. Through the scanning electron microscopy measurements, it was possible to indicate satisfactory definitions between native fibers and barrier, and that the measured values for the channel width revealed suitable fidelity (R2 = 0.99) with the nominal widths (ranging from 400 to 5000 µm). The proposed hydrophobic barrier exhibited excellent chemical resistance. The analytical applicability for detecting sAA revealed linear behavior in the range from 2 to 12 U mL-1 (R2 = 0.99), limit of detection of 0.75 U mL-1, reproducibility (RSD ≤2.4%), recovery experiments ranged from 89 to 108% and AGREE response (0.86). In addition, the colorimetric analysis of sAA in four different saliva samples demonstrated levels ranging from 202 to 2080 U mL-1, which enabled monitoring the absence and presence of periodontitis. SIGNIFICANCE: This report has presented the first use of a self-adhesive mask and glass varnish for creating circular zones and microfluidic architectures on paper without using thermic or UV curing treatments. Also, the proposed analytical methodology for detecting sAA exhibited suitable ecological impact considering the AGREE tool. We believe the proposed fabrication of paper devices emerges as a novel, simple, high-fidelity microfluidic channel and portable analytical approach for colorimetric sensing.

3D printing of electrochemical cell for voltammetric detection and photodegradation monitoring of folic acid in juice samples.

In this study, compact 3D-printed carbon black (CB) electrodes were manufactured for using in folic acid (FA) analysis in fruit samples. Before application in FA analysis, the electrode surfaces were characterized by high-resolution scanning electron microscopy and voltammetry using well-known redox probes. Square wave voltammetric study presented linear responses in the range between 10 and 200 µmol/L (R2 > 0.99), exhibited a suitable detection limit (LOD) of âˆ¼ 5.1 µmol/L and acceptable performance in terms of reproducibility and anti-interference experiments. The analysis of FA in four different food samples using the proposed method agreed statistically with a comparative technique based on spectrophotometric measurements. Moreover, results from photostability experiments indicated that FA can be degraded after 5 and 20 min of UV exposure. These results successfully demonstrated the analytical feasibility of the 3D-printed electrodes as sensing material and for monitoring the photostability of FA in different fruit matrices.

Office paper and laser printing: a versatile and affordable approach for fabricating paper-based analytical devices with multimodal detection capabilities.

Multiple protocols have been reported to fabricate paper-based analytical devices (PADs). However, some of these techniques must be revised because of the instrumentation required. This paper describes a versatile and globally affordable method to fabricate PADs using office paper as a substrate and a laser printing technique to define hydrophobic barriers on paper surfaces. To demonstrate the feasibility of the alternatives proposed in this study, the fabrication of devices for three types of detection commonly associated with using PADs was demonstrated: colorimetric detection, electrochemical detection, and mass spectrometry associated with a paper-spray ionization (PSI-MS) technique. Besides that, an evaluation of the type of paper used and chemical modifications required on the substrate surface are also presented in this report. Overall, the developed protocol was suitable for using office paper as a substrate, and the laser printing technique as an efficient fabrication method when using this substrate is accessible at a resource-limited point-of-need. Target analytes were used as a proof of concept for these detection techniques. Colorimetric detection was carried out for acetaminophen, iron, nitrate, and nitrite with limits of detection of 0.04 µg, 4.5 mg mL-1, 2.7 µmol L-1, and 6.8 µmol L-1, respectively. A limit of detection of 0.048 fg mL-1 was obtained for the electrochemical analysis of prostate-specific antigen. Colorimetric and electrochemical devices revealed satisfactory performance when office paper with a grammage of 90 g m-2 was employed. Methyldopa analysis was also carried out using PSI-MS, which showed a good response in the same paper weight and behavior compared to chromatographic paper.

Direct immunoassay on a polyester microwell plate for colorimetric detection of the spike protein in swab and saliva samples.

This study presents the development of a polyester microplate for detecting the S-protein of the SARS-CoV-2 virus in saliva and nasopharyngeal swab samples using direct enzyme-linked immunosorbent assay (ELISA) technology. The polyester microplate was designed to contain 96 zones with a 3 mm diameter each, and a volume of 2-3 µL. The experimental conditions including reagent concentration and reaction time were optimized. The microplate image was digitized and analyzed using graphical software. The linear range obtained between protein S concentrations and pixel intensity was 0-10 µg mL-1, with a correlation coefficient of 0.99 and a limit of detection of 0.44 µg mL-1. The developed methodology showed satisfactory intraplate and interplate repeatability with RSD values lower than 7.8%. The results achieved through immunoassay performed on polyester microplates were consistent with those of the RT-PCR method and showed a sensitivity of 100% and 90% and specificity of 85.71% and 100% for saliva and nasopharyngeal samples, respectively. The proposed direct immunoassay on polyester microplates emerges as an alternative to conventional immunoassays performed on commercial polystyrene plates, given the low cost of the device, low consumption of samples and reagents, lower waste generation, and shorter analysis time. Moreover, the immunoassay has shown great potential for diagnosing COVID-19 with precision and accuracy.

Distance-based detection of paracetamol in microfluidic paper-based analytical devices for forensic application.

Whisky adulteration is a prevalent practice driven by the high cost of these beverages. Counterfeiters commonly dilute whisky with less expensive alcoholic beverages, water, food additives, drugs or pharmaceuticals. Paracetamol (PAR), an analgesic drug that mitigates hangovers and headaches, is commonly used to adulterate whisky. Currently, the primary method for quantifying PAR levels is high-performance liquid chromatography, but this technique is both time consuming and usually generates more residues. In this context, the utilization of miniaturized and portable analytical devices becomes imperative for conducting point-of-care/need analyses. These devices offer several advantages, including portability, user-friendliness, low cost, and minimal material wastage. This study proposes the selective distance-based PAR quantification on whisky samples using a paper-based microfluidic analytical device (µPAD). Colorimetric detection on paper-based platforms offers great benefits such as affordability, portability, and the ability to detect PAR without complicated instrumentation. The optimal detection conditions were achieved by introducing 5 µL of a mixture containing 7.5 mmol L-1 of Fe(III) and K3[Fe(CN)6] into the detection zone, along with 12 µL of whisky samples into the sample zone. The method exhibited linear behavior within the concentration range from 15 to 120 mg L-1, with a determination coefficient of 0.998. PAR was quantified in adulterated samples. The results obtained with the paper-based devices were compared with a referenced method, and no significant differences were observed at a confidence level of 95%. The µPAD allowed to determine ca. 1 drop of pharmaceutical medicine PAR of 200 mg mL-1 in 1 L of solution, demonstrating excellent sensitivity. This method offers cost-effective and rapid analysis, reducing the consumption of samples, reagents, and wastes. Consequently, it could be considered a viable and portable alternative for analyzing beverages at criminal scenes, customs, and police operations, thereby enhancing the field of forensics.

Analysis of naphthenic acids in produced water samples by capillary electrophoresis-mass spectrometry.

A capillary electrophoresis-mass spectrometry method was used to analyze naphthenic acids in produced water samples. It was possible to detect cyclopentanecarboxylic, benzoic, cyclohexanebutyric, 1-naphthoic, decanoic, 3,5-dimethyladamantane-1-carboxylic, 9-anthracenecarboxylic, and pentadecanoic acids within ca. 13 min using a buffer composed of 40 mmol/L ammonium hydroxide, 32 mmol/L acetic acid and 20% v/v isopropyl alcohol, pH 8.6. The proposed method showed good repeatability, with relative standard deviation (RSD) values of 6.6% for the sum of the peak areas and less than 2% for the analysis time. In the interday analysis, the RSD values for the sum of the peak areas and migration time were 10.3% and 10%, respectively. The developed method demonstrated linear behavior in the concentration range between 5 and 50 mg/L for benzoic, decanoic, 3,5-dimethyladamantane-1-carboxylic and 9-anthracenecarboxylic acids, and between 10 and 50 mg/L for cyclopentanecarboxylic, cyclohexanebutyric, 1- naphthoic, and pentadecanoic acids. The detection limits values ranged from 0.31 to 1.64 mg/L. Six produced water samples were analyzed and it was possible to identify and quantify cyclopentanecarboxylic, benzoic, cyclohexanebutyric, and decanoic acids. The concentrations varied between 4.8 and 98.9 mg/L, proving effective in the application of complex samples.

Polyester resin and graphite flakes: turning conductive ink to a voltammetric sensor for paracetamol sensing.

The development of a disposable electrochemical paper-based analytical device (ePAD) is described using a novel formulation of conductive ink that combines graphite powder, polyester resin, and acetone. As a proof of concept, the proposed sensor was utilized for paracetamol (PAR) sensing. The introduced ink was characterized via morphological, structural, and electrochemical analysis, and the results demonstrated appreciable analytical performance. The proposed ePAD provided linear behavior (R2 = 0.99) in the concentration range between 1 and 60 µmol L-1, a limit of detection of 0.2 µmol L-1, and satisfactory reproducibility (RSD ~ 7.7%, n = 5) applying a potential of + 0.81 V vs Ag at the working electrode. The quantification of PAR was demonstrated in different pharmaceutical formulations. The achieved concentrations revealed good agreement with the labeled values, acceptable accuracy (101% and 106%), and no statistical difference from the data obtained by HPLC at the 95% confidence level. The environmental impact of the new device was assessed using AGREE software, which determined a score of 0.85, indicating that it is eco-friendly. During the pharmacokinetic study of PAR, it was found that the drug has a maximum concentration of 23.58 ± 0.01 µmol L-1, a maximum time of 30 min, and a half-life of 2.15 h. These results are comparable to other studies that utilized HPLC. This suggests that the combination of graphite powder and polyester resin can transform conductive ink into an effective ePAD that can potentially be used in various pharmaceutical applications.

Preliminary assessment of toxicity of aerosol samples from central-west Brazil using Artemia spp. bioassays.

The present study reports the development of a bioassay using Artemia spp. to analyse the preliminary ecotoxicity of atmospheric aerosols (PM), which can affect the environment and human health. Herein, PM samples were collected in the city of Goiânia (Brazil) in 2016, extracted with ultrapure water and subsequently filtered through membranes with different pore sizes (100, 0.8, and 0.22 µm), and the extracts employed in the bioassays. The mortality rates (endpoint analysed) declined to membranes with smaller pore sizes (15 ± 4%, 47 ± 10% and 43 ± 9% for pore sizes of 100 µm, 0.8 µm and 0.22 µm, respectively). In general, the toxicity of the extract depended on its concentration, except for the sample with a higher negative particle surface charge, which presents a lower affinity for the negatively charged surfaces of cellular membranes. Moreover, although the PM concentration was higher for the sample collected during the dry season (September), the mortality rate was not significantly different to that determined for a sample with similar physical and chemical characteristics collected in the rainy season (December). This result demonstrates the importance of monitoring PM toxicities and their chemical and physical characteristics, in addition to their concentrations. Therefore, the new protocol to provide a preliminary analysis of the toxicity of the extracts of aerosol emerges as a useful, accessible, and fast tool for monitoring possible environmental hazards, and can simplify fieldwork.

Digital microfluidic platform assembled into a home-made studio for sample preparation and colorimetric sensing of S-nitrosocysteine.

Digital microfluidics (DMF) is a versatile lab-on-a-chip platform that allows integration with several types of sensors and detection techniques, including colorimetric sensors. Here, we propose, for the first time, the integration of DMF chips into a mini studio containing a 3D-printed holder with previously fixed UV-LEDs to promote sample degradation on the chip surface before a complete analytical procedure involving reagent mixture, colorimetric reaction, and detection through a webcam integrated on the equipment. As a proof-of-concept, the feasibility of the integrated system was successfully through the indirect analysis of S-nitrosocysteine (CySNO) in biological samples. For this purpose, UV-LEDs were explored to perform the photolytic cleavage of CySNO, thus generating nitrite and subproducts directly on DMF chip. Nitrite was then colorimetrically detected based on a modified Griess reaction, in which reagents were prepared through a programable movement of droplets on DMF devices. The assembling and the experimental parameters were optimized, and the proposed integration exhibited a satisfactory correlation with the results acquired using a desktop scanner. Under the optimal experimental conditions, the obtained CySNO degradation to nitrite was 96%. Considering the analytical parameters, the proposed approach revealed linear behavior in the CySNO concentration range between 12.5 and 400 µmol L-1 and a limit of detection equal to 2.8 µmol L-1. Synthetic serum and human plasma samples were successfully analyzed, and the achieved results did not statistically differ from the data recorded by spectrophotometry at the confidence level of 95%, thus indicating the huge potential of the integration between DMF and mini studio to promote complete analysis of lowmolecular weight compounds.

Low-Cost Microfluidic Systems for Detection of Neglected Tropical Diseases.

Neglected tropical diseases (NTDs) affect tropical and subtropical countries and are caused by viruses, bacteria, protozoa, and helminths. These kinds of diseases spread quickly due to the tropical climate and limited access to clean water, sanitation, and health care, which make exposed people more vulnerable. NTDs are reported to be difficult and inefficient to diagnose. As mentioned, most NTDs occur in countries that are socially vulnerable, and the lack of resources and access to modern laboratories and equipment intensify the difficulty of diagnosis and treatment, leading to an increase in the mortality rate. Portable and low-cost microfluidic systems have been widely applied for clinical diagnosis, offering a promising alternative that can meet the needs for fast, affordable, and reliable diagnostic tests in developing countries. This review provides a critical overview of microfluidic devices that have been reported in the literature for the detection of the most common NTDs over the past 5 years.

Recycling 3D Printed Residues for the Development of Disposable Paper-Based Electrochemical Sensors.

Here, we propose a recyclable approach using acrylonitrile-butadiene-styrene (ABS) residues from additive manufacturing in combination with low-cost and accessible graphite flakes as a novel and potential mixture for creating a conductive paste. The graphite particles were successfully incorporated in the recycled thermoplastic composite when solubilized with acetone and the mixture demonstrated greater adherence to different substrates, among which cellulose-based material made possible the construction of a paper-based electrochemical sensor (PES). The morphological, structural, and electrochemical characterizations of the recycled electrode material were demonstrated to be similar to those of the traditional carbon-based surfaces. Faradaic responses based on redox probe activity ([Fe(CN)6]3-/4-) exhibited well-defined peak currents and diffusional mass transfer as a quasi-reversible system (96 ± 5 mV) with a fast heterogeneous rate constant value of 2 × 10-3 cm s-1. To improve the electrode electrochemical properties, both the PES and the classical 3D-printed electrode surfaces were modified with a combination of multiwalled carbon nanotubes (MWCNTs), graphene oxide (GO), and copper. Both electrode surfaces demonstrated the suitable oxidation of nitrite at 0.6 and 0.5 V vs Ag, respectively. The calculated analytical sensitivities for PES and 3D-printed electrodes were 0.005 and 0.002 µA/(µmol L-1), respectively. The proposed PES was applied for the indirect amperometric analysis of S-nitroso-cysteine (CysNO) in serum samples via nitrite quantitation, demonstrating a limit of detection of 4.1 µmol L-1, with statistically similar values when compared to quantitative analysis of the same samples by spectrophotometry (paired t test, 95% confidence limit). The evaluated electroanalytical approach exhibited linear behavior for nitrite in the concentration range between 10 and 125 µmol L-1, which is suitable for realizing clinical diagnosis involving Parkinson's disease, for example. This proof of concept shows the great promise of this recyclable strategy combining ABS residues and conductive particles in the context of green chemical protocols for constructing disposable sensors.

"Do it yourself" protocol to fabricate dual-detection paper-based analytical device for salivary biomarker analysis.

This paper describes the design and construction of dual microfluidic paper-based analytical devices (dual-µPADs) as a lab-on-paper platform involving a "do-it-yourself" fabrication protocol. The device comprises a colorimetric and electrochemical module to obtain a dual-mode signal readout sensing strategy. A 3D pen polymeric resin was used to prepare graphite carbon-based electrodes and hydrophobic barriers on paper substrates. The proposed carbon-based ink was employed to manufacture electrodes on paper based on a stencil-printing approach, which were further characterized by electrochemical and morphological analyses. The analytical performance of the dual-µPADs was simultaneously evaluated for lactate, pH, nitrite, and salivary amylase (sAA) analysis. To demonstrate the proof-of-concept, saliva samples collected from both healthy individuals and those with periodontitis were successfully tested to demonstrate the feasibility of the proposed devices. Samples collected from individuals previously diagnosed with periodontitis showed high levels of nitrite and sAA (> 94 µmol L-1 and > 610 U mL-1) in comparison with healthy individuals (≤ 16 µmol L-1 and 545 U mL-1). Moreover, periodontitis saliva resulted in acid solution and almost null lactate levels. Notably, this protocol supplies a simple way to manufacture dual-µPADs, a versatile platform for sensitive detecting of biomarkers in saliva playing a crucial role towards the point-of-care diagnosis of periodontal disease.

Silicone glue-based graphite ink incorporated on paper platform as an affordable approach to construct stable electrochemical sensors.

This study describes the development of electrochemical paper-based analytical devices (ePADs) using carbon-based paste combining silicone glue and graphite powder. The ePADs were manufactured using the screen-printing technique, which consisted of depositing the conductive ink on a screencast on the paper surface. In addition, an alternative electrical connector was designed and 3D-printed to make the detection method cheaper, portable and reproducible. The morphological, structural, and electrochemical properties of the conductive material developed were investigated through scanning electron microscopy (SEM), Raman spectroscopy, electrochemical impedance spectroscopy (EIS), and cyclic voltammetry (CV) measurements. The ePADs combined with the alternative connector revealed high repeatability, reproducibility, and stable responses considering a well-known redox probe ([Fe(CN)6]4-/3-). In addition, the proposed ePAD provided a linear response for standard solutions of ascorbic acid (AA) in the concentration range between 0.1 and 2.0 mmol L-1. The achieved limit of detection was 4.0 µmol L-1. As proof of applicability, the ePADs were evaluated for AA analysis in synthetic biofluids (blood plasma and urine), vitamin C tablets, and food (gelatine and orange juice) samples. The analytical parameters of the proposed device were compared with other reports in the literature and exhibited similar or even superior performance, highlighting its feasibility for sensing applications.

Electrokinetic characterization of hybrid NOA 81-glass microchips: Application to protein microchip electrophoresis with indirect fluorescence detection.

A low-cost and straightforward hybrid NOA (Norland optical adhesive) 81-glass microchip electrophoresis device was designed and developed for protein separation using indirect fluorescence detection. This new microchip was first characterized in terms of surface charge density via electroosmotic mobility measurement and stability over time. A systematic determination of the electroosmotic mobility (µeo ) over a wide pH range (2-10) and at various ionic strengths (20-50 mM) was developed for the first time via the neutral marker approach in an original simple frontal methodology. The evolution of µeo was proved consistent with the silanol and thiol functions arising from the glass and the NOA materials, respectively. The repeatability and reproducibility of the measurements on different microchips (RSD < 14%) and within 15 days (less than 5% decrease) were successfully demonstrated. The microchip was then applied for the efficient electrophoretic separation of proteins in a zonal mode coupled with indirect fluorescence detection, which is, to our knowledge, the first proof of concept of capillary zone electrophoresis in this hybrid microsystem.

Determination of naphthenic acids in produced water by using microchip electrophoresis with integrated contactless conductivity detection.

This study reports for the first time the use of a microchip electrophoresis (ME) device with integrated capacitively coupled contactless conductivity detection (C4D) to analyze naphthenic acids in produced water. A mixture containing 9-anthracenecarboxylic, 1-naphthoic, and benzoic acids was separated and detected using a running buffer composed of 10 mmol L-1 carbonate buffer (pH = 10.2). The separation was achieved within ca. 140 s with baseline resolution greater than 2 and efficiency values ranging from 1.9 × 105 to 2.4 × 105 plates m-1. The developed methodology provided linear correlation with determination coefficients greater than 0.992 for the concentration ranges between 50 and 250 µmol L-1 for benzoic and 9-anthracenecarboxylic acids, and between 50 and 200 µmol L-1 for 1-naphthoic acid. The achieved limit of detection values varied between 4.7 and 7.7 µmol L-1. The proposed methodology revealed satisfactory repeatability with RSD values for a sequence of eight injections between 5.5 and 7.7% for peak areas and lower than 1% for migration times. In addition, inter-day precision was evaluated for sixteen injections (a sequence of four injections performed during four days), and the RSD values were lower than 11.5 and 4.9% for peak areas and migration time, respectively. Five produced water samples were analyzed, and it was possible to detect and quantify 9-anthracenecarboxylic acid. The concentrations ranged from 1.05 to 2.24 mmol L-1 with recovery values between 90.8 and 96.0%. ME-C4D demonstrated satisfactory analytical performance for determining naphthenic acids in produced water for the first time, which is useful for petroleum or oil industry investigation.

3D-printed electrochemical platform with multi-purpose carbon black sensing electrodes.

The 3D printing is described of a complete and portable system comprising a batch injection analysis (BIA) cell and an electrochemical platform with eight sensing electrodes. Both BIA and electrochemical cells were printed within 3.4 h using a multimaterial printer equipped with insulating, flexible, and conductive filaments at cost of ca. ~ U$ 1.2 per unit, and their integration was based on a threadable assembling without commercial component requirements. Printed electrodes were exposed to electrochemical/Fenton pre-treatments to improve the sensitivity. Scanning electron microscopy and electrochemical impedance spectroscopy measurements upon printed materials revealed high-fidelity 3D features (90 to 98%) and fast heterogeneous rate constants ((1.5 ± 0.1) × 10-3 cm s-1). Operational parameters of BIA cell were optimized using a redox probe composed of [Fe(CN)6]4-/3- under stirring and the best analytical performance was achieved using a dispensing rate of 9.0 µL s-1 and an injection volume of 2.0 µL. The proof of concept of the printed device for bioanalytical applications was evaluated using adrenaline (ADR) as target analyte and its redox activities were carefully evaluated through different voltammetric techniques upon multiple 3D-printed electrodes. The coupling of BIA system with amperometric detection ensured fast responses with well-defined peak width related to the oxidation of ADR applying a potential of 0.4 V vs Ag. The fully 3D-printed system provided suitable analytical performance in terms of repeatability and reproducibility (RSD ≤ 6%), linear concentration range (5 to 40 µmol L-1; R2 = 0.99), limit of detection (0.61 µmol L-1), and high analytical frequency (494 ± 13 h-1). Lastly, artificial urine samples were spiked with ADR solutions at three different concentration levels and the obtained recovery values ranged from 87 to 118%, thus demonstrating potentiality for biological fluid analysis. Based on the analytical performance, the complete device fully printed through additive manufacturing technology emerges as powerful, inexpensive, and portable tool for electroanalytical applications involving biologically relevant compounds.

3D printed microfluidic mixer for real-time monitoring of organic reactions by direct infusion mass spectrometry.

3D printing is a technology that has revolutionized traditional rapid prototyping methods due to its ability to build microscale structures with customized geometries in a simple, fast, and low-cost way. In this sense, this article describes the development of a microfluidic mixing device to monitor chemical reactions by mass spectrometry (MS). Microfluidic mixers were designed containing 3D serpentine and Y-shaped microchannels, both with a pointed end for facilitating the spray formation. The devices were fabricated entirely by 3D printing with fusion deposition modeling (FDM) technology. As proof-of-concept, micromixers were evaluated through monitoring the Katritzky reaction by injecting simultaneously 2,4,6-triphenylpropyllium (TPP) and amino acid (glycine or alanine) solutions, each through a different reactor inlet. Reaction product was monitored online by MS at different flow rates. Mass spectra showed that the relative abundances of the products obtained with the device containing the 3D serpentine channel were three times greater than those obtained with the Y-channel device due to the turbulence generated by the barriers created inside microchannels. In addition, when compared to the conventional electrospray ionization mass spectrometry (ESI-MS) technique, the 3D serpentine mixer offered better performance measured in relation to the relative abundance values for the reaction products. These results as well as the instrumental simplicity indicate that 3D printed microfluidic mixer is a promising tool for monitoring organic reactions via MS.