An Experimental Analysis of the High-Cycle Fatigue Fracture of H13 Hot Forging Tool Steels.

In this study, the axial fatigue behaviour of hot forging tool steels at room temperature was investigated. Fatigue tests were performed on two steels within the same H13 specification. The fatigue tests were carried out in the high-cycle fatigue domain under normal conditions. These tests were also performed on specimens in contact with a corrosive medium, applying stress values that led to the high-cycle fatigue domain under normal conditions for the sake of comparison. Both materials showed similar fatigue strengths when they were tested under normal conditions. In contrast, corrosion fatigue lives were much lower than in normal tests and differed significantly between the two steels. Crack initiation was triggered by microstructural and surface defects in the normal tests, whereas the formation of corrosion pits caused crack initiation in the corrosion fatigue tests. Moreover, a fracture surface analysis revealed dissimilar crack propagation areas between both steels, which suggested that both steels had different fracture toughness. These results were in line with the differences observed between the carbide and grain sizes of both of the material microstructures.

Characterization of Co-Cr-W Dental Alloys with Veneering Materials Manufactured via Subtractive Milling and Additive Manufacturing LDED Methods.

Laser-directed energy deposition (LDED) is an additive manufacturing (AM) technology which can be an alternative to the traditional subtractive milling process for the obtention of porcelain-fused-to-metal (PFM) prosthesis. Still, the adhesion performance of the veneering ceramics for this material has been not studied yet. The main objective of this study is to perform a systematic comparison of the adhesion performance of Co-Cr-W metal frameworks obtained through LDED and conventional milling techniques. Comparison includes microstructural, superficial, and adhesion analysis. Co-Cr manufactured via LDED technique presents similar behavior (p < 0.05) in comparison to the material obtained via milling techniques, and its performance was validated with the veneering ceramics and veneering composites currently employed in the dental industry.

Analytical Model for the Fatigue Analysis of Steel Joints by Clamps According to the Lever Length.

Among the most commonly used materials in the construction of structures in the last two centuries are iron and steel. Clamp joints are a suitable type of joint when it is necessary to rehabilitate or modify a historical steel structure for new uses, reinforcing or modifying it with new beams, without the need to drill or weld on the original structure. The clamps allow beams to be joined with a flange (such as I-beams) without the need for any prior operation on the beams and allow the manufacture of completely removable and reconfigurable structures. Developing and analysing this type of fully removable and reconfigurable structure is necessary. To date, no studies have been carried out on the fatigue behaviour of steel joints by clamps, especially taking into account their main geometric characteristics, such as the size of the clamp levers. In this work, an analytical model is proposed that allows for the analysis of the number of cycles and the fatigue limit of clamp joints as a function of the size of the clamp levers. In addition, various fatigue tests are performed with different clamp sizes. The experimental results are compared with those obtained with the proposed methodology. Finally, the relationships between the lever length and the fatigue behaviour of the clamp joints have been determined. It is concluded that an increase in the size of the front lever is associated to a decrease in the fatigue limit. On the contrary, if the size of the rear lever is increased, the fatigue limit of the joint increases. In general, according to the obtained results, the resistance of the joint can be reduced to approximately one third when it is subjected to fatigue loads.

Hyaluronic acid hydrogels reinforced with laser spun bioactive glass micro- and nanofibres doped with lithium.

The repair of articular cartilage lesions in weight-bearing joints remains as a significant challenge due to the low regenerative capacity of this tissue. Hydrogels are candidates to repair lesions as they have similar properties to cartilage extracellular matrix but they are unable to meet the mechanical and biological requirements for a successful outcome. Here, we reinforce hyaluronic acid (HA) hydrogels with 13-93-lithium bioactive glass micro- and nanofibres produced by laser spinning. The glass fibres are a reinforcement filler and a platform for the delivery of therapeutic lithium-ions. The elastic modulus of the composites is more than three times higher than in HA hydrogels. Modelling of the reinforcement corroborates the experimental results. ATDC5 chondrogenic cells seeded on the composites are viable and more proliferation occurs on the hydrogels containing fibres than in HA hydrogels alone. Furthermore, the chondrogenic behavior on HA constructs with fibres containing lithium is more marked than in hydrogels with no-lithium fibres.

Laser-Guided Corrosion Control: A New Approach to Tailor the Degradation of Mg-Alloys.

Despite corrosion being commonly seen as a problem to be avoided, applications such as batteries or biodegradable implants do benefit from corrosion-like phenomena. However, current strategies address corrosion control from a global perspective for a whole component, without considering local adaptations to functionality specifications or inhomogeneous environments. Here, a novel concept is presented: the local control and guidance of corrosion through a laser surface treatment. Immersion tests in saline solution of AZ31 magnesium alloy samples show degradation rates reduced up to 15 times with the treatment, owing to a fast passivation after the induced microstructural modifications. By controlling the treatment conditions, the degradation can be restricted to delimited regions and driven towards specific directions. The applicability of the method for the design of tailored degradation biomedical implants is demonstrated and uses for cathodic protection systems and batteries can also be anticipated.

Laser Microdrilling of Slate Tiles.

Slate is a natural rock usually used in roofs, façades, and for tiling. In spite of this broad use, the production process of slate tiles requires substantial improvements. An important quantity of slate from the quarry is wasted during the manufacturing of the final product. Furthermore, processes are not automatized and the production lead times can be considerably shortened. Therefore, new processing methods to increase productivity, reduce costs and to provide added value to the final slate product are required. Drilling is an important part of these manufacturing processes. Conventional drilling processes usually cause the breaking of the slate tiles; then, even a higher quantity of material is wasted. To overcome these problems, lasers emerge as a feasible tool to produce holes in this material, since mechanical stresses are not induced on the workpiece. In this work, we have studied the CO2 laser microdrilling of slate tiles. We used a Design of Experiments (DOE) methodology to determine the influence of the laser processing parameters on the hole quality. This work demonstrates the capability of a CO2 laser to produce holes in slate with less than 100 microns in diameter, avoiding any fracture, and with a processing time of less than 50 ms per hole. Finally, this process demonstrates the viability of the production of high-density micron-sized holes in a slate tile for water draining purposes.

Laser Cutting: A Review on the Influence of Assist Gas.

Assist gas plays a central role in laser fusion cutting. In this work, the aerodynamic interactions between the assist gas and the workpiece are reviewed. An insight into those phenomena that hinder the cutting quality and performance is provided. These phenomena include shock waves, choking, boundary layer separation, etc. The most relevant and promising attempts to overcome these common problems related to the gas dynamics are surveyed. The review of the current scientific literature has revealed some gaps in the current knowledge of the role of the assist gas dynamics in laser cutting. The assist gas interactions have been investigated only under static conditions; and the dynamic interaction with the molten material on the cutting front has not been addressed. New nozzle designs with improved efficiency of molten material removal are required to improve cut quality; and cutting speed in current industrial laser cutting machines; especially in those assisted by new high-brightness laser sources.

Determination of forces on a split palatal screw after rapid maxillary expansion.

OBJECTIVES: Aim of this study was to develop a finite element model of the forces that patients with rapid maxillary expansion bear and to validate it by a mechanical test. METHODS: Computer-aided design models of the metallic screw and polymeric splint were modelled and discretized. Two forces were generated and considered independently: F1 at the temporary molar (2.5 N) and F2 at the permanent molar (2.5 N). The results of the finite element analysis were used to define the strain values which the anterior and posterior arms of the rapid maxillary expansion appliance bore as a linear function of F1-F2 by calculating the strain-force coefficient δ ij . Two strain gauge rosettes were attached to an appliance which was placed in an XY motorized stage to reproduce the same forces used in the finite element analysis. Once the system was validated, the matrix was inverted to determine forces F1 and F2 that a group of 40 patients underwent (median age 8.33 years, standard deviation 1.86 years) for 75 days, using their strain values. The parents of the patients activated a quarter turn (0.20 mm) twice a day until 50% transversal overcorrection was achieved. RESULTS: Finite element analysis showed that the effects of the forces on stress at the location of the arms were notably different. There was a satisfactory correlation between finite element analysis predictions and in vitro values. Dissipation of F1 and F2 in patients was predicted to be 62.5 and 80%, respectively, after 75 days of retention. CONCLUSION: These results back the finite element analysis model for force prediction.

Effect of low-level laser therapy after rapid maxillary expansion: a clinical investigation.

To evaluate the effectiveness low-level laser therapy (LLLT) on the repair of the mid palatal suture, after rapid maxillary expansion (RME). A single-operator, randomized single-blind placebo-controlled study was performed at the Orthodontic Department at the Dental Hospital of Bellvitge. Barcelona University, Hospitalet de Llobregat, Spain. Thirty-nine children (range 6-12 years old), completed RME and were randomized to receive active LLLT (n = 20) or placebo (n = 19). The laser parameters and dose were 660 nm, 100 mW, CW, InGaAlP laser, illuminated area 0.26 cm(2), 332 mW/cm(2), 60 s to four points along midpalatal suture, and 30 s to a point each side of the suture. A total of seven applications were made on days 1, 7, 14, 28, 42, 56, and 70 of the retention phase RME. A cone beam computed tomography (CBCT) scan was carried out on the day of the first laser treatment, and at day 75, a second CBCT scan was performed. Two radiologists synchronized the slices of two scans to be assessed. P = 0.05 was considered to be statistically significant. At day 75 of the suture, the irradiated patients presented a greater percentage of approximate zones in the anterior (p = 0.008) and posterior (p = 0.001) superior suture-and less approximation in the posterior superior suture (p = 0.040)-than the placebo group. LLLT appears to stimulate the repair process during retention phase after RME.

Short-term effects of strain produced on a split palatal screw-type hyrax appliance after rapid maxillary expansion: A clinical trial.

INTRODUCTION: The aim of this study was to establish an accumulated strain pattern in different parts of rapid maxillary expansion appliances and relate them to different vertical growth patterns. A clinical study was conducted of 40 patients with posterior crossbite who required rapid palatal expansion. METHODS: Patients (mean age, 8.48 years) were recruited and treated at the Dental Hospital of Bellvitge, Hospitalet de Llobregat, Barcelona, Spain. Strain gauges were placed on the arms of the RME hyrax screw appliance to record deformation (strain) during the expansion and the retention phases for 75 days. A finite element model was used to place the gauge at the point where the strain was most expressed. The vertical coefficient of variation was used to classify the patients by their vertical growth pattern. P = 0.05 was considered to be statistically significant. RESULTS: During the expansion phase, the highest values of accumulated strain were measured in the posterior part of the appliance for all facial biotypes, but these values passed to the anterior area at the end of the retention phase of the mesocephalic and brachycephalic patients. There was statistically significant difference in the strain of the posterior arms in accordance with the vertical growth pattern (P = 0.05) during the retention phase. At 75 days of retention, 61.25% of the arms had already begun to have strain dissipation. CONCLUSIONS: The accumulated strain pattern in the rapid maxillary expansion appliance can vary depending on the facial biotype. In the future, orthodontists should try to tailor the activation and retention protocol based on each patient's characteristics.

Toward smart implant synthesis: bonding bioceramics of different resorbability to match bone growth rates.

Craniofacial reconstructive surgery requires a bioactive bone implant capable to provide a gradual resorbability and to adjust to the kinetics of new bone formation during healing. Biomaterials made of calcium phosphate or bioactive glasses are currently available, mainly as bone defect fillers, but it is still required a versatile processing technique to fabricate composition-gradient bioceramics for application as controlled resorption implants. Here it is reported the application of rapid prototyping based on laser cladding to produce three-dimensional bioceramic implants comprising of a calcium phosphate inner core, with moderate in vitro degradation at physiological pH, surrounded by a bioactive glass outer layer of higher degradability. Each component of the implant is validated in terms of chemical and physical properties, and absence of toxicity. Pre-osteoblastic cell adhesion and proliferation assays reveal the adherence and growth of new bone cells on the material. This technique affords implants with gradual-resorbability for restoration of low-load-bearing bone.

Production of nanoparticles from natural hydroxylapatite by laser ablation.

Laser ablation of solids in liquids technique has been used to obtain colloidal nanoparticles from biological hydroxylapatite using pulsed as well as a continuous wave (CW) laser. Transmission electron microscopy (TEM) measurements revealed the formation of spherical particles with size distribution ranging from few nanometers to hundred nanometers and irregular submicronic particles. High resolution TEM showed that particles obtained by the use of pulsed laser were crystalline, while those obtained by the use of CW laser were amorphous. The shape and size of particles are consistent with the explosive ejection as formation mechanism.