Testing a novel biotechnological passive sampler for monitoring atmospheric PAH pollution.

In this study we evaluated a new type of passive air sampler, the "mossphere" device, filled with a Sphagnum palustre clone. For this purpose, we compared the atmospheric levels of polyaromatic hydrocarbons (PAHs) collected using this device and those collected in conventional bulk deposition and particulate matter (PM10) samplers. All three types of samplers were exposed at 10 sites affected by different levels of pollution and located in two different climate zones. The bulk deposition/ mossphere comparison yielded a greater number of significant regressions with higher coefficients of determination than the PM10/ mossphere comparison. No significant regressions were observed for 3-ring PAHs in either comparison. The mosspheres explain ca. 50% of the variability of the concentrations of 4-, 5- and 6-ring PAHs and total PAHs detected in PM10 and ca. 70% of the corresponding concentrations detected in the bulk deposition. The use of the Sphagnum clone enables standardization of the set-up, thus making the mossphere device a good sampling tool for monitoring 4-, 5- and 6-ring and total PAHs, especially those associated with bulk deposition. The findings indicate the potential usefulness of this innovative technology for mapping PAH levels.

PAH detection in Quercus robur leaves and Pinus pinaster needles: A fast method for biomonitoring purpose.

Due to the complexity and heterogeneity of plant matrices, new procedure should be standardized for each single biomonitor. Thus, here is described a matrix solid-phase dispersion extraction method, previously used for moss samples, improved and modified for the analyses of PAHs in Quercus robur leaves and Pinus pinaster needles, species widely used in biomonitoring studies across Europe. The improvements compared to the previous procedure are the use of Florisil added with further clean-up sorbents, 10% deactivated silica for pine needles and PSA for oak leaves, being these matrices rich in interfering compounds, as shown by the gas chromatography-mass spectrometry analyses acquired in full scan mode. Good trueness, with values in the range 90-120% for the most of compounds, high precision (intermediate precision between 2% and 12%) and good sensitivity using only 250mg of samples (limits of quantification lower than 3 and 1.5ngg(-1), respectively for pine and oak) were achieved by the selected procedures. These methods proved to be reliable for PAH analyses and, having advantage of fastness, can be used in biomonitoring studies of PAH air contamination.

Blank and sample handling troubleshooting in ultratrace analysis of alkylphenols and bisphenol A by liquid chromatography tandem mass spectrometry.

Blank contamination is a notorious problem in the ultratrace analysis of alkylphenols and bisphenol A. The achievement of low detection limits is complicated due to the high background signals. Furthermore, overestimations and underestimations in the analytical results can occur when blank levels are not stable. Thus, a review of sources of blank contamination in this type of analysis was carried out. Several sources of contamination were identified and useful guidelines are proposed for the determination of these compounds in water samples by liquid chromatography coupled with mass spectrometry. The system contamination was maintained below 0.09 ng (reagent blank) for all compounds and below 0.003 µg L(-1) (procedure blank). The main improvement was obtained by using LC-MS grade solvent in the mobile phase and PTFE syringe filters for the filtration of the sample extracts. Sample handling aspects such as filtration and storage of the water samples were also considered. The filtration of the samples should be avoided because both contamination and adsorption problems were observed when different kinds of filters were assayed. The refrigerated storage of water samples should be limited to 5 days (without addition of methanol) or 8 days (with 5% methanol).

Determination of alkylphenols and bisphenol A in seawater samples by dispersive liquid-liquid microextraction and liquid chromatography tandem mass spectrometry for compliance with environmental quality standards (Directive 2008/105/EC).

A fast, simple, sensitive and green analytical chemistry method for the simultaneous determination of alkylphenols (4-tert-octylphenol, 4-octylphenol, 4-n-nonylphenol, nonylphenol) and bisphenol A in seawater was developed and validated. The procedure was based on a dispersive liquid-liquid microextraction (DLLME) of a small volume of seawater sample (30 mL) using only 100 µL of 1-octanol, combined with liquid chromatography-electrospray ionization tandem mass spectrometry in negative mode (LC-ESI-MS/MS). The matrix effect was studied and compensated using deuterated labelled standards as surrogate standards for the quantitation of target compounds. The analytical features of the proposed method were satisfactory: repeatability and intermediate precision were <10% and recoveries were around 84-104% for all compounds. Uncertainty assessment of measurement was estimated on the basis of an in-house validation according to EURACHEM/CITAC guide. Quantitation limits of the method (MQL) ranged between 0.005 and 0.03 µg L⁻¹, therefore the levels established in the Directive 2008/105/EC were achieved. The applicability of the proposed method was demonstrated analyzing seawater samples from different sites of A Coruña (Northwest of Spain). The analyses showed the presence of all compounds at levels between 0.035 (bisphenol A) and 0.14 µg L⁻¹ (nonylphenol).

Development of an environmental friendly method for the analysis of organochlorine pesticides in sediments.

This work proposes a pressurized hot water extraction (PHWE) followed by solid phase microextraction (SPME) and determination by gas chromatography-mass spectrometry method for the analysis of organochlorine pesticides in sediment samples. For SPME, extraction temperature and time, desorption temperature and desorption time, and effect of an organic modifier were studied. For PHWE, parameters such as organic modifier, percentage of organic modifier, temperature, and static extraction time were studied. When these parameters were selected, the figures of merit were calculated in order to assess the performance of the proposed method. Quantitative recoveries (80-115%) and satisfactory precisions were obtained. The detection and quantification limits were between 0.11 and 16 microg kg(-1) and between 0.24 and 22 microg kg(-1), respectively with good linearity between LOQs and 500 microg kg(-1) for most of the studied pesticides. The method was validated by the analysis of a reference marine sediment material (SRM 1944). The obtained results are in excellent agreement with the certificate material. Another sediment reference material (SRM 1941b), with a very low concentration of pesticides was also analyzed with good results. In addition, this method was successfully applied to the analysis of three marine sediment samples. The developed method seems to be a nearly full automated, environmental friendly, sensitive, simple and less-time consuming method. Moreover this method, look for the implementation of the principles of green analytical chemistry and has demonstrated to be suitable for the analysis of organochlorine pesticides at trace levels in environmental matrices as sediment samples.

A study of large-volume on-column injection GC-ECD for the ultratrace analysis of organochlorine pesticides in water.

In this work, a large-volume on-column injection method for the analysis of 21 organochlorine pesticides, including HCH isomers, DDT derivatives and cyclodiene derivatives, was optimized. The solvent selected to carry out the study was ethyl acetate and the injection volume was 100 microl. Some factors were introduced in a Plackett-Burman design to determine their influence in the vaporization efficiency. The significant factors were then studied by a univariate procedure and sorted according to their importance on the response. The effect of the injection conditions on the peak resolution was also noted. The conditions selected according to sensitivity and resolution were: initial oven temperature 75 degrees C, injection speed 20 microl s(-1), solvent vapor exit (SVE) valve closure time 60 s, initial pressure 100 kPa and isothermal oven time 1 min. Analytical characteristics expressed in terms of precision, linear range, and limit of detection have been determined and compared with those obtained by splitless injection. The degradation of endrin and p,p'-DDT thermolabile pesticides was evaluated for both injection techniques. Finally the developed method was successfully applied to the ultratrace analysis of pesticides in natural waters. With this purpose a micro liquid-liquid extraction method using 2 ml of ethyl acetate to extract 10 ml of water sample was proposed. Recoveries between 69 and 107% were obtained with a very good precision (0.2-1.3%) for the studied pesticides, except for p,p'-DDD. Detection limits between 0.3 and 25 ng l(-1), which fulfill the limits established by the new water directive 2008/105/EC, were achieved. The MLLE method was compared with the SPE method by the analysis of some water samples using both procedures, and good concordance was obtained.

Pressurized hot water extraction coupled to solid-phase microextraction-gas chromatography-mass spectrometry for the analysis of polycyclic aromatic hydrocarbons in sediments.

A fully automated, environmentally friendly, simple, and sensitive method was developed for the analysis of polycyclic aromatic hydrocarbons (PAHs) in sediment samples. The procedure is based on pressurized hot water extraction (PHWE) followed by solid-phase microextraction (SPME) and determination by gas chromatography-mass spectrometry. For PHWE, parameters such as organic modifier, percentage of organic modifier, temperature, and static extraction time were studied. For SPME, extraction temperature and time, desorption temperature and time, splitless time, ionic strength adjustments, and effect of an organic modifier were studied. When these parameters were selected, the figures of merit were calculated. The detection and quantification limits were between 0.4-15 microg kg(-1) and 1.2-51 microg kg(-1), respectively. The linearity of the method was assessed spiking sediment samples at seven levels of concentration ranged between 2.5 microg kg(-1) and 500 microg kg(-1) for most of the studied PAHs. The method was validated by two concentration levels reference marine sediment materials (SRM 1944 and SRM 1941b). The obtained results are in very good agreement with the certificate materials. The developed method seems to be suitable for the analysis of PAHs at ultratrace levels in environmental matrices as sediment samples.

A multivariate study of the programmed temperature vaporization injection-gas chromatographic-mass spectrometric determination of polycyclic aromatic hydrocarbons Application to marine sediments analysis.

The trace analysis of polycyclic aromatic hydrocarbons (PAHs) in environmental matrices requires highly sensitive and selective methods. The use of large-volume injection in gas chromatography with mass spectrometry detection allows the improvement of the sensitivity. In this work, one of the most popular large-volume injectors, programmed temperature vaporization (PTV)-splitless injection, was optimized to determine 26 alkylated and non-alkylated PAHs at ultratrace levels. The injection conditions that use two different injection volumes, 10 and 25mul, were optimized applying experimental designs. Six experimental factors that could affect the vaporization efficiency were studied. Detection limits for each assayed volume were compared with splitless injection, both in full scan and in SIM mode. An improvement of 50- and 100-fold, for 10 and 25mul, respectively, was achieved for PAHs in comparison with splitless injection. Finally, the method that was optimized for 25mul was applied successfully to the analysis of a certified marine sediment SRM 1941b and a real marine sediment extracted by microwave assisted extraction.

Solid-phase microextraction-gas chromatographic-tandem mass spectrometric analysis of polycyclic aromatic hydrocarbons. Towards the European Union water directive 2006/0129 EC.

This article presents a solid-phase microextraction (SPME) procedure to determine 27 parent and alkylated polycyclic aromatic hydrocarbons (PAHs) with diverging polarities and molecular masses in various types of water samples (tap, well, superficial, and seawater). A 65-microm polydimethylsiloxane-divinylbenzene (PDMS/DVB) fiber was used, and parameters affecting the extraction procedures such as extraction temperature and time, desorption temperature and time, splitless time, effect of an organic modifier or ionic adjustment were studied. The linearity and precision of the proposed method were satisfactory. The use of GC-MS determination in the full scan mode, in the selected ion monitoring (SIM) mode, and in the GC-MS-MS mode provided the unequivocal identification and quantification of the target analytes. Moreover, the proposed SPME-GC-MS-MS method, extracting only 18 ml of sample, reached the very restrictive limits fixed by the 2006/0129 EC proposal for a new water directive to be achieved by 2015. The matrix effects were evaluated through the analysis of tap, well, superficial, and seawater. A discussion on different behaviors, a result of the matrix effects, was included. Analytical recoveries were satisfactory in all cases. The novelty of this work consisted in the wide range of analyzed PAHs, the very low detection limits that were reached, the coupling of SPME-GC-MS-MS, and the study of the matrix effect on water samples. With this developed procedure, detection limits between 0.07 and 0.76 ng l(-1) and quantification limits between 0.10 and 0.98 ng l(-1) were obtained with MS-MS detection. Moreover, the analytical recoveries for different aqueous matrices were near 100% in all cases.

Pressurized liquid extraction of organochlorine pesticides from certified solid materials.

In order to propose a versatile method to use in laboratories devoted to environmental analysis, a scheme for the determination of organochlorine pesticides from different solid matrices is evaluated. Pressurized liquid extraction is chosen as the sample preparation technique, followed by the purification of the extract by means of solid-phase extraction with Envi-carb cartridge (100 m(2)/g). Finally, the extracts are analyzed by programmed temperature vaporization (PTV)-gas chromatography (GC)-electron-capture detection and PTV-GC-mass spectrometry. The suitability of the method for the analysis of different matrices is determined by the extraction and analysis of four certified reference materials of solid matrices: CRM 804-050 (soil), SRM 1941b (organics in marine sediment), SRM 1944 (New York/New Jersey waterway sediment) and SRM 1649a (Urban Dust). Good statistical concordance between the results obtained and the certified or reference concentration are observed for most of the analyzed pesticides.

Optimisation and validation of a solid-phase microextraction method for simultaneous determination of different types of pesticides in water by gas chromatography-mass spectrometry.

A solid-phase microextraction (SPME) method for the simultaneous determination of a large number of pesticides (46) with a wide range of polarities and chemical structures (organochlorine, organophosphorous, triazines, pyrethroids and others) in water samples by GC-MS has been developed. Three different fibres and parameters that influence the extraction and desorption efficiency were studied. The selected conditions were: a 60 microm polydimethylsiloxane/divinylbenzene (PDMS/DVB) fibre, 45 min of extraction time, sample agitation and temperature control at 60 degrees C; neither pH adjustment nor ionic strength correction were applied. Good detection limits, linearity and repeatability were obtained with this method for the 46 pesticides studied. The method was validated for 29 pesticides following the recommendations of the international norm ISO/IEC 17025 including the calculation of the uncertainties. The detection limits ranged from 4 to 17 ng l(-1). Furthermore, repeatability (6.9-20.5%) and intermediate precision (4.5-19.7%) were shown to be satisfactory. To validate matrix effects for drinking and surface water analytical recoveries were calculated for these matrices. The accuracy of the method was also evaluated by participating in a proficiency inter-laboratory test.

Evaluation of HCH isomers and metabolites in soils, leachates, river water and sediments of a highly contaminated area.

In this work we evaluate the contamination caused by HCH residues in the soil, leachates, river water and sediments of an industrial estate of the NW of Spain. We study the distribution of the isomers in the different matrices, analysing 37 soil samples, collected in eight points at several depths, six natural leachates, four river water samples and three river sediments. Soil and leachate samples present very high levels of HCH isomers, higher than the established by legislation, and some pesticides were also detected in the analysed river water whereas no pesticides were detected in the river sediments. The distribution of isomers was different depending on the matrix analysed. Some natural degradation products and also other organochlorine pesticides were detected in the samples analysed.

Troubleshooting with cell blanks in PLE extraction.

The blank extracts obtained from the pressurized liquid extraction (PLE) of a 11 mL empty cell of ASE 200 were analysed by GC-FID and GC-ECD and many interfering peaks were detected, which could difficult the trace analysis of persistent organic pollutants (i.e. polycyclic aromatic hydrocarbons, aliphatic hydrocarbons and organochlorine pesticides). These interfering compounds were identified as phthalates, silicones and organic acids and their sources were established. A solution to this analytical trouble is a previous extraction step of the empty cell under the same conditions optimised for the sample extraction.

Development of pressurized liquid extraction and cleanup procedures for determination of organochlorine pesticides in soils.

The scope of this work is the development of a rapid, reliable and sensitive method for the analysis of organochlorine pesticides from soils by pressurized liquid extraction (PLE). The effect of four parameters (temperature, pressure, static time and cell volume) on the extraction efficiency was studied. The great extracting power of the PLE causes the extraction of numerous interfering substances, so a more efficient purification of this extract was necessary. In this work several sorbents have also been assayed to carry out the purification of soil samples: Florisil, silica, alumina, carbon, as well as combinations of them. Finally, the proposed analytical method was validated using a certified reference soil material (CRM804-050) and the results were compared with those obtained by other extraction techniques (Soxhlet and microwave-assisted extraction).

Improvement of sensitivity in the determination of organochlorine pesticides using a PSS injector with GC-ECD.

This paper describes the optimisation of a PSS injector in a gas chromatograph with a programmed pneumatic control (PPC) for the determination of 21 organochlorine pesticides. The injection of high volumes of sample (20 microl) improves the detection limits and allows a reduction in the amount of sample processed. The injection conditions were selected by a Plackett-Burman design followed by a central composite design. The LODs obtained in the optimum conditions were compared with those obtained with splitless/ECD. Finally, the method was successfully applied to the analysis of a leachate and vegetable samples.

Microwave-assisted extraction versus Soxhlet extraction in the analysis of 21 organochlorine pesticides in plants.

A method to determine 21 organochlorine pesticides in vegetation samples using microwave-assisted extraction (MAE) is described and compared with Soxhlet extraction. Samples were extracted with hexane-acetone (1:1, v/v) and the extracts were cleaned using solid-phase extraction with Florisil and alumine as adsorbents. Pesticides were eluted with hexane-ethyl acetate (80:20, v/v) and determined by gas chromatography and electron-capture detection. Recoveries obtained (75.5-132.7% for Soxhlet extraction and 81.5-108.4% for MAE) show that both methods are suitable for the determination of chlorinated pesticides in vegetation samples. The method using microwave energy was applied to grass samples from parks of A Coruña (N.W. Spain) and to vegetation from the contaminated industrial area of Torneiros (Pontevedra, N.W. Spain).

Microwave extraction of organochlorine pesticides from soils.

The purpose of this work was to develop a rapid, reliable and sensitive method for the extraction of organochlorine pesticides from soils using microwave energy with closed vessel technology. Three oven programs were assayed with two different solvent mixtures in order to achieve adequate experimental conditions for the complete extraction of organochlorine pesticides from the matrix. The method was validated using a certified reference soil material (CRM804-050).

Optimisation of a programmed split-splitless injector in the gas chromatographic-mass spectrometric determination of organochlorine pesticides.

Large-volume injection techniques in gas chromatography are used to compensate for the at times limited detection sensitivity of mass spectrometric detection. In this work a programmed split-splitless injector in solvent split mode was employed to determine organochlorine pesticides in environmental samples. The injection conditions were selected by a Plackett-Burman design followed by a central composite design. The LODs obtained in the optimum conditions were compared with those obtained with splitless-MS and splitless-ECD. Finally, the method was applied to a soil sample.