RESUMEN
Conventional methods of metal recovery involving solvents have raised environmental concerns. To address these concerns and promote sustainable resource recovery, we explored the use of deep eutectic solvents (DES) and chelating agents (CA) as more environmentally friendly alternatives. Goethite and blast oxide slag dust (BOS-D) from heap piles at their respective sites and characterised via ICP-MS. The greatest extraction of critical metals was from goethite, removing 38% of all metals compared to 21% from the blast oxide slag. Among the tested CA, nitrilotriacetic acid (NTA) was the most effective, while for DES, choline chloride ethylene glycol (ChCl-EG) demonstrated superior performance in extracting metals from both blast oxide slag dust and goethite. The study further highlighted the selectivity for transition metals and metalloids was influenced by the carboxyl groups of DES. Alkaline metals and rare earth lanthanides extractions were favoured with DES due to improved mass transfer and increased denticity, respectively. In comparison to ethylenediaminetetraacetic acid (EDTA), typically used for metal extraction, CA and DES showed comparable extraction efficiency for Fe, Cu, Pb, Li, Al, Mn, and Ni. Using these greener chelators and solvents for metal extraction show significant promise in enhancing the sustainability of solvometallurgy. Additional conditions e.g., temperature and agitation combined with a cascading leaching process could further enhance metal extraction potential.
Asunto(s)
Quelantes , Ácido Edético , Metales , Quelantes/química , Ácido Edético/química , Metales/química , Disolventes Eutécticos Profundos/química , Solventes/químicaRESUMEN
This study aimed to optimise metal extraction from secondary hazardous sources, such as basic oxygen steelmaking dust (BOS-D). Initially, three batch systems approaches, including bioleaching using Acidithiobacillus ferrooxidans, chemical leaching using choline chloride-ethylene glycol (ChCl-EG) and a combined approach were compared. Then, scaling up was evaluated through a semi-continuous bioleaching column system with varied leachate recirculation over 21 days, focusing on Y, Ce, Nd, Li, Co, Cu, Zn, Mn, and Al. Bioleaching outperformed the control experiments within 3 days in the batch, demonstrating the key role of A. ferrooxidans. Chemical leaching conducted with a solid concentration of 12.5 % (w/v) successfully dissolved over 50 % of all metals within 2 h. For rare earth elements (REE), both bioleaching and hybrid leaching outperformed chemical leaching. However, considering factors such as process duration, overall efficiency, and ease of extraction, chemical leaching was the most effective method. Leachate recirculation reached a plateau after 11 days, resulting in extraction efficiency of 39 % when semi-continuous column set-up was used. Interestingly, variations in recirculation rates did not influence the extraction efficiency. Overall, this study emphasizes the considerable potential of bioleaching for metal recovery, but also highlights the need for further studies for enhancing permeability for percolation methods and optimisation, particularly in parameters such as aeration rate, when transitioning to larger scale systems.
RESUMEN
Per- and poly-fluoroalkyl substances (PFAS) have emerged as newly regulated micropollutants, characterised by extreme recalcitrance and environmental toxicity. Constructed wetlands (CWs), as a nature-based solution, have gained widespread application in sustainable water and wastewater treatment and offer multiple environmental and societal benefits. Despite CWs potential, knowledge gaps persist in their PFAS removal capacities, associated mechanisms, and modelling of PFAS fate. This study carried out a systematic literature review, supplemented by unpublished experimental data, demonstrating the promise of CWs for PFAS removal from the influents of varying sources and characteristics. Median removal performances of 64, 46, and 0 % were observed in five free water surface (FWS), four horizontal subsurface flow (HF), and 18 vertical flow (VF) wetlands, respectively. PFAS adsorption by the substrate or plant root/rhizosphere was deemed as a key removal mechanism. Nevertheless, the available dataset resulted unsuitable for a quantitative analysis. Data-driven models, including multiple regression models and machine learning-based Artificial Neural Networks (ANN), were employed to predict PFAS removal. These models showed better predictive performance compared to various mechanistic models, which include two adsorption isotherms. The results affirmed that artificial intelligence is an efficient tool for modelling the removal of emerging contaminants with limited knowledge of chemical properties. In summary, this study consolidated evidence supporting the use of CWs for mitigating new legacy PFAS contaminants. Further research, especially long-term monitoring of full-scale CWs treating real wastewater, is crucial to obtain additional data for model development and validation.
RESUMEN
This study investigated the effectiveness of incorporating sulphur (S) with nitrogen (N) and phosphorus (P) for enhancing microbial activity in diesel-contaminated soil during ex-situ bioremediation. While N and P amendments are commonly used to stimulate indigenous microorganisms, the potential benefits of adding S have received less attention. The study found that historically contaminated soil with a moderate concentration of total petroleum hydrocarbons (TPH; 1270 mg/kg) did not have nutrient limitation, and incubation temperature was found to be more critical for enhancing microbial activity. However, soil spiked with an additional 5000 mg/kg of diesel showed increased activity following NP and NPS amendment. Interestingly, NPS amendment at 10 °C resulted in higher microbial activity than at 20 °C, indicating the potential for a tailored nutrient amendment approach to optimize bioremediation in cold conditions. Overall, this study suggests that incorporating S with N and P can enhance microbial activity in diesel-contaminated soil during ex-situ bioremediation. Furthermore, the study highlights the importance of considering incubation temperature in designing a nutrient amendment approach for bioremediation, especially in cold conditions. These findings can guide the design and implementation of future effective bioremediation strategies for petroleum hydrocarbon-contaminated soil.
RESUMEN
In Ecuador, the regulatory framework for the remediation of petroleum-contaminated soils is based on predefined concentration endpoints for a selected range of petroleum hydrocarbon compounds. However, such approach may lead to over or under-estimation of the environmental risk posed by contaminated soils. In this study, the end-point remediation criteria according to Ecuadorian Environmental legislation were evaluated using different approaches. The first one was based on Total Extractable Petroleum Hydrocarbons (TEPH) and the second one on Total Bioavailable Petroleum Hydrocarbons (TBPH). Both were compared with ecotoxicological determinations using EC50 -Microtox® bioassay at 5 and 15 min of exposure. The correlation (R2) between EC50 values vs TEPH was of 0.2 and 0.25 for 5 and 15 min, respectively. Meanwhile, R2 between EC50 and TBPH was of 0.9 and 0.65 for 5 and 15 min, respectively, demonstrating a stronger correlation. Our results suggest that a contaminated site where the concentration of the TEPH is higher than the relevant regulatory concentrations may be deemed to present an acceptable risk even though their concentrations exceed the target values in soils. The results also challenge the notion that hormesis is associated with TEPH, contrary to some literature. This study is the first in Ecuador to propose incorporating bioavailability into environmental regulations, highlighting the need for further research to establish realistic and achievable remediation goals based on toxicity studies involving various trophic levels.
RESUMEN
Environmental pollution is escalating due to rapid global development that often prioritizes human needs over planetary health. Despite global efforts to mitigate legacy pollutants, the continuous introduction of new substances remains a major threat to both people and the planet. In response, global initiatives are focusing on risk assessment and regulation of emerging contaminants, as demonstrated by the ongoing efforts to establish the UN's Intergovernmental Science-Policy Panel on Chemicals, Waste, and Pollution Prevention. This review identifies the sources and impacts of emerging contaminants on planetary health, emphasizing the importance of adopting a One Health approach. Strategies for monitoring and addressing these pollutants are discussed, underscoring the need for robust and socially equitable environmental policies at both regional and international levels. Urgent actions are needed to transition toward sustainable pollution management practices to safeguard our planet for future generations.
RESUMEN
Municipal effluents discharged from wastewater treatment plants (WWTPs) are a considerable source of microplastics in the environment. The dynamic profiles of microplastics in treatment units in WWTPs with different treatment processes remain unclear. This study quantitatively analyzed microplastics in wastewater samples collected from different treatment units in two tertiary treatment plants with distinct processes. The influents contained an average of 15.5 ± 3.5 particles/L and 38.5 ± 2.5 particles/L in the two WWTPs with in the oxidation ditch process and the integrated fixed-film activated sludge process, respectively. Interestingly, microplastic concentrations in the influent were more influenced by the population density in the served area than sewage volume or served population equivalent. Throughout the treatment process, concentrations were reduced to 1.5 ± 0.5 particles/L and 1.0 ± 1.0 particles/L in the final effluents, representing an overall decrease of 90% and 97%, in WWTPs with the oxidation ditch process and integrated fixed-film activated sludge process, respectively. A significant proportion of the microplastics were removed during the primary treatment stage in both WWTPs, with better performance for foam, film, line-shaped and large-sized microplastics. Most microplastics were accumulated in activated sludge, indicating its key role as the primary sink in WWTPs. The multiple correspondence analysis identified laundry washing and daily necessities such as packaging and containers as the major contributors to microplastics in WWTPs. The study proposed recommendations for upgrading WWTPs, modifying designs, and implementing strategies to reduce microplastic sources, aiming to minimize the release of microplastics into the environment. These findings can shed lights on the sources of microplastics in WWTPs, and advance our understanding of the mechanisms for more effective microplastic removals in wastewater treatment technologies in future applications.
Asunto(s)
Población Rural , Ingeniería Sanitaria , Eliminación de Residuos Líquidos , Población Rural/estadística & datos numéricos , Eliminación de Residuos Líquidos/métodos , Aguas Residuales/química , Purificación del Agua , Ingeniería Sanitaria/métodos , Ingeniería Sanitaria/tendencias , Aparatos Sanitarios/provisión & distribuciónRESUMEN
This study focused on the economic feasibility of two potential industrial-scale bioleaching technologies for metal recovery from specific metallurgical by-products, mainly basic oxygen steelmaking dust (BOS-D) and goethite. The investigation compared two bioleaching scaling technology configurations, including an aerated bioreactor and an aerated and stirred bioreactor across different scenarios. Results indicated that bioleaching using Acidithiobacillus ferrooxidans proved financially viable for copper extraction from goethite, particularly when 5% and 10% pulp densities were used in the aerated bioreactor, and when 10% pulp density was used in the aerated and stirred bioreactor. Notably, a net present value (NPV) of $1,275,499k and an internal rate of return (IRR) of 65% for Cu recovery from goethite were achieved over 20-years after project started using the aerated and stirred bioreactor plant with a capital expenditure (CAPEX) of $119,816,550 and an operational expenditure (OPEX) of $5,896,580/year. It is expected that plant will start to make profit after one year of operation. Aerated and stirred bioreactor plant appeared more reliable alternative compared to the aerated bioreactor plant as the plant consists of 12 reactors which can allow better management and operation in small volume with multiple reactors. Despite the limitations, this techno-economic assessment emphasized the significance of selective metal recovery and plant design, and underscored the major expenses associated with the process.
Asunto(s)
Acidithiobacillus , Reactores Biológicos , Metalurgia , Acidithiobacillus/metabolismo , Cobre , Minerales , Compuestos de HierroRESUMEN
Diagnostic features in near-infrared reflectance spectroscopy (NIRS) are the foundation of knowledge-based approach of petroleum hydrocarbon determination. However, a significant challenge arises when analyzing samples with low levels of petroleum hydrocarbon pollution, as they often lack distinctive diagnostic features in their sample NIRS spectra, limiting the effectiveness of this approach. To address this issue, we have developed a technical workflow for diagnostic spectrum construction and parameterization based on spectral subtraction. This method was applied on a set of NIRS spectra from soil samples that were contaminated with petroleum hydrocarbons (ranged between 178 and 1716 mg/kg of total petroleum hydrocarbon). Then two diagnostic features for low-level petroleum hydrocarbon pollution were found: (1) An overall downward concave emerged on diagnostic spectrum within both 2290-2370 nm and 1700-1780 nm for all low pollution levels even below 200 mg/kg; (2) An indicative pattern of asymmetric "W-shaped" double absorption valley occurred for those exceeding 1000 mg/kg, and its valleys located near 2310 nm, 2348 nm or 1727 nm, 1762 nm stably. These two features on diagnostic spectrum could be parameterized to detect, and the detection limit was at least about 10-50 times lower than that based on sample spectrum. These findings update our understanding on the detectability of spectral response from low petroleum hydrocarbon pollution, and widely extend the application of knowledge-based NIRS approach in either field detection or remote sensing identification for environmental management.
RESUMEN
The combination of urbanization and global warming leads to urban overheating and compounds the frequency and intensity of extreme heat events due to climate change. Yet, the risk of urban overheating can be mitigated by urban green-blue-grey infrastructure (GBGI), such as parks, wetlands, and engineered greening, which have the potential to effectively reduce summer air temperatures. Despite many reviews, the evidence bases on quantified GBGI cooling benefits remains partial and the practical recommendations for implementation are unclear. This systematic literature review synthesizes the evidence base for heat mitigation and related co-benefits, identifies knowledge gaps, and proposes recommendations for their implementation to maximize their benefits. After screening 27,486 papers, 202 were reviewed, based on 51 GBGI types categorized under 10 main divisions. Certain GBGI (green walls, parks, street trees) have been well researched for their urban cooling capabilities. However, several other GBGI have received negligible (zoological garden, golf course, estuary) or minimal (private garden, allotment) attention. The most efficient air cooling was observed in botanical gardens (5.0 ± 3.5°C), wetlands (4.9 ± 3.2°C), green walls (4.1 ± 4.2°C), street trees (3.8 ± 3.1°C), and vegetated balconies (3.8 ± 2.7°C). Under changing climate conditions (2070-2100) with consideration of RCP8.5, there is a shift in climate subtypes, either within the same climate zone (e.g., Dfa to Dfb and Cfb to Cfa) or across other climate zones (e.g., Dfb [continental warm-summer humid] to BSk [dry, cold semi-arid] and Cwa [temperate] to Am [tropical]). These shifts may result in lower efficiency for the current GBGI in the future. Given the importance of multiple services, it is crucial to balance their functionality, cooling performance, and other related co-benefits when planning for the future GBGI. This global GBGI heat mitigation inventory can assist policymakers and urban planners in prioritizing effective interventions to reduce the risk of urban overheating, filling research gaps, and promoting community resilience.
RESUMEN
Monitored natural attenuation (MNA) of chlorinated ethenes (CEs) has proven to be a cost-effective and environment-friendly approach for groundwater remediation. In this study, the complete dechlorination of CEs with formation of ethene under natural conditions, were observed at two CE-contaminated sites, including a pesticide manufacturing facility (PMF) and a fluorochemical plant (FCP), particularly in the deeply weathered bedrock aquifer at the FCP site. Additionally, a higher abundance of CE-degrading bacteria was identified with heightened dechlorination activities at the PMF site, compared to the FCP site. The reductive dehalogenase genes and Dhc 16 S rRNA gene were prevalent at both sites, even in groundwater where no CE dechlorination was observed. vcrA and bvcA was responsible for the complete dechlorination at the PMF and FCP site, respectively, indicating the distinct contributions of functional microbial species at each site. The correlation analyses suggested that Sediminibacterium has the potential to achieve the complete dechlorination at the FCP site. Moreover, the profiles of CE-degrading bacteria suggested that dechlorination occurred under Fe3+/sulfate-reducing and nitrate-reducing conditions at the PMF and FCP site, respectively. Overall these findings provided multi-lines of evidence on the diverse mechanisms of CE-dechlorination under natural conditions, which can provide valuable guidance for MNA strategies implementation.
Asunto(s)
Chloroflexi , Agua Subterránea , Contaminantes Químicos del Agua , Biodegradación Ambiental , Bacterias/genética , Etilenos , Agua Subterránea/microbiologíaRESUMEN
Zero-valent iron (ZVI) has been extensively studied for its efficacy in removing heavy metals, nitrate, and chlorinated organic compounds from contaminated water. However, its limited effectiveness due to rapid passivation and poor selectivity is prompting for alternative solutions, such as the use of aluminium alloys. In this study, the efficacy of five distinct aluminium alloys, namely Al-Mg, Al-Fe, Al-Cu, and Al-Ni, each comprising 50 % Al by mass at a concentration of 10 g/L, was assessed using copper, nitrate and trichloromethane (TCM) as model contaminants. Results show that chemical pollutants reacted immediately with Al-Mg. On the contrary, the remaining three alloys exhibited a delay of 24 h before demonstrating significant reactivity. Remarkably, Al-Mg alloy reduced nitrate exclusively to ammonium, indicating minimal preference for nitrate reduction to N2. In contrast, the Al-Cu, Al-Ni, and Al-Fe alloys exhibited N2 selectivity of 3 %, 5 %, and 19 %, respectively. The removal efficiency of copper, nitrate and TCM reached 99 % within 24 h, 95 % within 48h and 48 % within 48h, respectively. Noteworthy findings included the correlation between Fe concentration within the Al-Fe alloy and an increased N2 selectivity from 9.3 % to 24.1 %. This resulted in an increase of Fe concentration from 10 % to 58 % albeit with a concurrent reduction in reactivity. Cu2+ removal by Al-Fe alloy occurred via direct electron transfer, while the removal of nitrate and TCM was facilitated by atomic hydrogen generated by the alloy's hydrolysis. Intriguingly, nitrate and TCM suppressed Cu2+ reduction, whereas Cu2+ improved nitrate reduction and TCM degradation. These findings demonstrate the great potential of Al-Mg and Al-Fe alloys as highly efficient agents for water remediation.
RESUMEN
In low and medium income countries (LMIC) drinking water sources (wells and boreholes) often contain a high number of pathogenic microorganisms, that can pose significant human and environmental health risks. In this study, a quantitative microbial risk assessment approach based on existing literature was conducted to evaluate and compare the quantitative health risks associated with different age groups using various drinking water supply systems. Results showed that both community-supply and self-supply modes exhibit similar levels of risk. However, the self-supply water source consistently showed higher risks compared to the community-supply one. Borehole water was found to be a more suitable option than well water, consistently showing between 5 and 8 lower health risks for E. coli and fecal coliform levels, respectively. The sensitivity analysis further showed the importance of prioritizing the reduction of E. coli concentration in well water and fecal coliform concentration in borehole water. This study offers a fresh perception on quantifying the impact of exposure concentration and age groups, shedding light on how they affect environmental health risks. These findings provide valuable insights for stakeholders involved in the management and protection of water sources.
Asunto(s)
Agua Potable , Humanos , Escherichia coli , Abastecimiento de Agua , Medición de Riesgo , Microbiología del AguaRESUMEN
This research evaluates a novel decision support system (DSS) for planning brownfield redevelopment. The DSS is implemented within a web-based geographical information system that contains the spatial data informing three modules comprising land use suitability, economic viability, and ground risk. Using multi-criteria decision analysis, an evaluation was conducted on 31,942 ha of post-industrial land and around Liverpool, UK. The representativeness and credibility of the DSS outputs were evaluated through user trials with fifteen land-use planning and development stakeholders from the Liverpool City Region Comined Authority. The DSS was used to explore land use planning scenarios and it could be used to support decision making. Our research reveals that the DSS has the potential to positively inform the identification of brownfield redevelopment opportunities by offering a reliable, carefully curated, and user-driven digital evidence base. This expedites the traditionally manual process of conducting assessments of land suitability and viability. This research has important implications for assessing the impact of current and future planning policy and the potential for the use of digital tools for land use planning and sustainability in the UK and globally.
Asunto(s)
Sistemas de Información Geográfica , Industrias , Poder PsicológicoRESUMEN
In this study, the potential of bioleaching to extract valuable metals from industrial by-products, specifically basic oxygen steelmaking dust (BOS-D) and goethite was investigated. These materials are typically discarded due to their high zinc content and lack of efficient regeneration processes. By using Acidithiobacillus ferrooxidans, successful bioleaching of various metals, including heavy metals, critical metals, and rare earth elements was achieved. The Taguchi orthogonal array design was used to optimise the bioleaching process, considering four variables at three different levels. After 14 days, the highest metal extraction for the BOS-D (11.2 mg Zn/g, 3.2 mg Mn/g, 1.6 mg Al/g, 0.0013 mg Y/g, and 0.0026 mg Ce/g) was achieved at 1% solid concentration, 1% energy source concentration, 1% inoculum concentration, and pH 1.5. For goethite, the optimal conditions were 1% solid concentration, 4% energy source concentration, 10% inoculum concentration, and pH 2 resulting in a extraction of 26.6 mg Zn/g, 2.1 mg/g Mn, 1.8 mg Al/g, 0.01 mg Co/g, 0.0022 mg Y/g. These findings are significant, as they demonstrate the potential to extract valuable metals from previously discarded industrial by-products. The extraction of such metals can have substantial economic and environmental implications, while simultaneously reducing waste in the metallurgical industry. Furthermore, the preservation of initial concentration of iron in both BOS-D and goethite residues represents a significant step towards implementing more sustainable industrial practices.
RESUMEN
The demand for munitions that are less likely to detonate accidentally has led to an increased use of Insensitive High Explosives (IHE), which contain substances like 2,4-dinitroanisole (DNAN) and 5-nitro-1,2,4-triazol-3-one (NTO). These substances have different properties compared to traditional explosives, and their potential environmental impact is not well understood. When these explosives are used in live-fire training exercises, their residues end up in the soil. It is important to determine how these residues dissolve and enter the soil. This study aimed to experimentally measure the rate at which an IHE formulation dissolves when exposed to rainwater with pH levels of 5.0 and 6.5, and to simulate how these residues dissolve and move through two different soil types. The dissolution rates were determined by conducting experiments in which IHE particles (30-60 mg) were exposed to water with varying pH levels and temperatures. The results showed that the dissolution rate of NTO did not vary with pH, while the dissolution rate of DNAN and RDX decreased with decreasing pH. Specifically, the dissolution rate of DNAN decreased from 18 ± 40 µg min-1 at pH 6.5 to 6 ± 4 µg min-1 at pH 5.0, while the dissolution rate of RDX decreased from 8 ± 4 to 3 ± 1 µg min-1. These findings were used to develop a stochastic model that successfully simulated the concentration of IHE in the leachate from soil columns over time. A sensitivity analysis revealed that while dissolution rates determined the amount of mass entering the soil, they did not significantly regulate the amount of mass that migrated through the soil and leached out of the soil columns.
RESUMEN
There is increasing demand for low-carbon remediation strategies for reducing greenhouse gas emissions and promoting sustainable development in the management of environmental contamination. This trend is within the broader context of sustainable remediation strategies that balance environmental, economic, and social aspects. This article critically reviewed existing literature to evaluate and compare various low-carbon remediation methods, such as bioremediation, phytoremediation, in situ chemical oxidation, soil vapour extraction, and electrokinetic remediation, to identify suitable techniques for the remediation of oil-contaminated sites in the Niger Delta region of Nigeria. We analysed the UK sustainable remediation frameworks (SuRF-UK) to glean lessons for the Nigerian context. Our findings indicate that bioremediation and phytoremediation are particularly promising low-carbon remediation technologies for the Niger Delta region due to their cost-effectiveness and adaptability to local conditions. We proposed a framework that deeply considers opportunities for achieving multiple goals including effective remediation and limited greenhouse gas emissions while returning net social and economic benefit to local communities. The proposed framework will help decision makers to implement effective remediation technologies that meet sustainability indices, integrates emissions considerations return net environmental benefit to local communities. There is a need for policymakers to establish and enforce policies and regulations that support sustainable remediation practises, build the capacity of stakeholders, invest in research and development, and promote collaboration among stakeholders to create a regulatory environment that supports sustainable remediation practises and promotes environmental sustainability in the region. This study provides insights for achieving low-carbon remediation in regions addressing land contamination by different contaminants and facilitates the adoption of remediation technologies that consider contextual socio-economic and environmental indices for sustainable development.