Enzymes' Power for Plastics Degradation.

Plastics are everywhere in our modern way of living, and their production keeps increasing every year, causing major environmental concerns. Nowadays, the end-of-life management involves accumulation in landfills, incineration, and recycling to a lower extent. This ecological threat to the environment is inspiring alternative bio-based solutions for plastic waste treatment and recycling toward a circular economy. Over the past decade, considerable efforts have been made to degrade commodity plastics using biocatalytic approaches. Here, we provide a comprehensive review on the recent advances in enzyme-based biocatalysis and in the design of related biocatalytic processes to recycle or upcycle commodity plastics, including polyesters, polyamides, polyurethanes, and polyolefins. We also discuss scope and limitations, challenges, and opportunities of this field of research. An important message from this review is that polymer-assimilating enzymes are very likely part of the solution to reaching a circular plastic economy.

Bio-Based Poly(hydroxy urethane)s for Efficient Organic High-Power Energy Storage.

Fast, low-cost, and efficient energy storage technologies are urgently needed to balance the intermittence of sustainable energy sources. High-power capacitors using organic polymers offer a green and scalable answer. They require dielectrics with high permittivity (εr) and breakdown strength (EB), which bio-based poly(hydroxy urethane)s (PHUs) can provide. PHUs combine high concentrations of hydroxyl and carbamate groups, thus enhancing their εr, and a highly tunable glass transition (Tg), which dictates the regions of low dielectric losses. By reacting erythritol dicarbonate with bio-based diamines, fully bio-based PHUs were synthesized with Tg ∼ 50 °C, εr > 8, EB > 400 MV·m-1, and low losses (tan δ < 0.03). This results in energy storage performance comparable with the flagship petrochemical materials (discharge energy density, Ue > 6 J·cm-3) combined with a remarkably high discharge efficiency, with η = 85% at EB and up to 91% at 0.5 EB. These bio-based PHUs thus represent a highly promising route to green and sustainable energy storage.

Mannose-based surfactant as biofunctional nanoemulsion stabilizer.

The development and implementation of new amphiphiles based on natural resources rather than petrochemical precursors is an essential requirement due to their feedstock depletion and adverse environmental impacts. In addition, the use of bio-based surfactants can provide unique characteristics and improve the properties and versatility of the colloidal systems in which they are applied, such as emulsions. Here, the emulsification properties of a synthesized biocompatible mannose-based surfactant were investigated. Its behavior was evaluated in the presence of four different natural oils (castor, sunflower, olive and soybean) as well as two different aqueous phases (pure water and phosphate-buffered saline). The results highlighted its interest as surfactant in O/W nanoemulsions for all tested oil and aqueous phases, using a low-energy preparation protocol and relatively low surfactant concentrations. Furthermore, the mannose groups present on the polar head of the surfactant and adsorbed on the surface of the emulsion droplets were shown to retain their native biological properties. The specific mannose-concanavalin A binding was observed in vitro by the designed nanoemulsions, revealing the biorecognition properties of the surfactant and its potential applicability as a nanocarrier.

Synthesis and Characterization of Vanillin-Based π-Conjugated Polyazomethines and Their Oligomer Model Compounds.

The synthesis of π-conjugated polymers via an environmentally friendly procedure is generally challenging. Herein, we describe the synthesis of divanillin-based polyazomethines, which are derived from a potentially bio-based monomer. The polymerization is performed in 5 min under microwave irradiation without any metallic catalyst, with water as the only by-product. The vanillin-based polyazomethines were characterized by SEC, TGA, and UV-Vis spectroscopy. Model compounds were designed and characterized by X-ray diffraction and UV-Vis spectroscopy. The structure/properties study of vanillin-based azomethines used as models allowed us to unequivocally confirm the E configuration and to highlight the cross-conjugated nature of divanillin-based polymers.

Design and Self-Assembly of Sugar-Based Amphiphiles: Spherical to Cylindrical Micelles.

Sugar-based amphiphiles are a relevant natural alternative to synthetic ones due to their biodegradable properties. An understanding of their structure-assembly relationship is needed to allow the concrete synthesis of suitable derivatives. Here, four different mannose-derivative surfactants are characterized by pendant drop, dynamic light scattering, small-angle X-ray scattering, cryotransmission electron microscopy, and molecular dynamics techniques in aqueous media. Measurements denote how the polysaccharide average degree of polymerization (DP¯) and the addition of a hydroxyl group to the hydrophobic tail, and thus the presence of a second hydrophilic moiety, affect their self-assembly. A variation in the DP¯ of the amphiphile has no effect in the critical micelle concentration in contrast to a change in the hydrophobic molecular region. Moreover, high-DP¯ amphiphiles self-assemble into spherical micelles irrespective of the hydroxyl group presence. Low-DP¯ amphiphiles with only one hydrophilic moiety form cylindrical micelles, while the addition of a hydroxyl group to the tail leads to a spherical shape.

Oxidative Depolymerization of Alkaline Lignin from Pinus Pinaster by Oxygen and Air for Value-Added Bio-Sourced Synthons.

In this work, an efficient 3-step process targeting the chemical modification and purification of lignin oligomers from industrial alkaline lignin is described. The oxidative depolymerization process of alkaline lignin with O2 or Air pressure, without use of metal catalyst, led to the production of two fractions of lignin oligomers named 'precipitated lignin' and 'hydrosoluble lignin' with 40% and 60% yield, respectively. These fractions were characterized with a wide range of methods including NMR spectroscopy (31P, 2D-HSQC), SEC (in basic media), FTIR. NMR analyses revealed the presence of carboxylic acid functions at a ratio of 1.80 mmol/g and 2.80 mmol/g for the precipitated and hydrosoluble lignin, respectively, values much higher than what is generally found in native lignin (between 0.2 and 0.5 mmol/g). SEC analyses revealed the formation of low molar masses for the precipitated (2200 g/mol) and hydrosoluble fractions (1500 g/mol) in contrast to the alkaline lignin (3900 g/mol). It is worth noting that the hydrosoluble fraction of lignin is soluble in water at any pH. Both processes (oxygen and air) were successfully scaled up and showed similar results in terms of yield and functionalization.

Extraction and Characterization of Hemicelluloses from a Softwood Acid Sulfite Pulp.

Hemicelluloses were extracted from a softwood acid sulfite pulp in a three-step procedure. Further delignification step resulted in a holocellulose pulp containing only 1.7 wt.% of the lignin left. Cold caustic extraction (CCE) with 18 wt.% NaOH at 60 °C for 1 h was performed to solubilize hemicelluloses of the holocellulose. An unbleached cellulose pulp was then obtained 97% pure, which indicates that 89% of the hemicelluloses were removed. After purification, extraction yields between 1.1 wt.% and 9.5 wt.% were obtained from the delignified pulp and the hemicelluloses' chemical compositions and structures were investigated by 1H, 13C nuclear magnetic resonance spectroscopy (NMR) and two-dimensional NMR by correlation spectroscopy (2D-COSY) and proton-detected heteronuclear single-quantum correlation (2D-HSQC), high-performance anion-exchange chromatography coupled with a pulsed amperometry detector (HPAEC-PAD), size-exclusion chromatography coupled with a refractive index detector (SEC-RI) and thermogravimetric analyses (TGA). Hemicelluloses were obtained with a purity of 96%, with short cellulosic chains as the only residue. Sulfite pulping modified the hemicelluloses' structure, and it was found that two types of hemicelluloses were isolated, glucomannans, predominant at 67%, and methylglucuronoxylans. Finally, alkali-soluble hemicelluloses displayed relatively narrow size distributions and low molar masses, Mw varying between 18,900 and 30,000 g/mol after acid sulfite pulping.

Functional Polyethylenes by Organometallic-Mediated Radical Polymerization of Biobased Carbonates.

Partly or fully renewable (co)polymers are gaining interest in both academia and industry. Polyethylene is a widely used polymer, classically derived from fossil fuels, with a high versatility stemming from the introduction of comonomers altering the mechanical properties. The introduction of renewable functionalities into this polymer is highly attractive to obtain functional, tunable, and at least partially renewable polyethylenes. We herein report the introduction of biosourced cyclic carbonates into polyethylene using organometallic-mediated radical polymerization under mild conditions. Molecular weights of up to 14 600 g mol-1 with dispersities as low as 1.19 were obtained, and the cyclic carbonate content could be easily tuned by the ethylene pressure during the polymerization. As a proof of concept, the hydrolysis of the cyclic carbonates of a representative copolymer was explored, and it provided polyethylene-bearing vicinal diols, with a hydrolysis degree of 71%. Given the multitude of chemoselective modifications possible on cyclic carbonates as well as the fact that many allylic- and alkylidene-type cyclic carbonates are accessible from renewable resources, this work opens up an avenue for the design of functional and more sustainable polyethylenes.

Enantioselective Crystallization of Diglycerol Dicarbonate: Impact of the Microstructure on Polyhydroxyurethane Properties.

Bicylic carbonates are precursors employed in non-isocyanate polyurethane syntheses, namely polyhydroxyurethanes (PHUs) and, among them, ether-activated biobased diglycerol dicarbonate (DGDC) is widely investigated. Herein, the original separation of DGDC stereoisomers, thanks to a recrystallization procedure, leading to enantiomers having different crystal lattices, that is, square transparent crystals and needle-like structures, respectively, is reported. In this study, the separation and the characterization of the two crystal structures is first discussed and, second, the impact of the stereochemistry of DGDC on the corresponding PHUs properties is investigated.

Divanillin-Based Polyazomethines: Toward Biobased and Metal-Free π-Conjugated Polymers.

Divanillin was synthesized in high yield and purity using Laccase from Trametes versicolor. It was then polymerized with benzene-1,4-diamine and 2,7-diaminocarbazole to form polyazomethines. Polymerizations were performed under microwave irradiation and without transition-metal-based catalysts. These biobased conjugated polyazomethines present a broad fluorescence spectrum ranging from 400 to 600 nm. Depending on the co-monomer used, polyazomethines with molar masses of around 10 kg·mol-1 and with electronic gaps ranging from 2.66 to 2.85 eV were obtained. Furthermore, time-dependent density functional theory (TD-DFT) calculations were performed to corroborate the experimental results.

Bio-Based Thermo-Reversible Aliphatic Polycarbonate Network.

Aliphatic polycarbonates represent an important class of materials with notable applications in the biomedical field. In this work, low Tg furan-functionalized bio-based aliphatic polycarbonates were cross-linked thanks to the Diels-Alder (DA) reaction with a bis-maleimide as the cross-linking agent. The thermo-reversible DA reaction allowed for the preparation of reversible cross-linked polycarbonate materials with tuneable properties as a function of the pendent furan content that was grafted on the polycarbonate backbone. The possibility to decrosslink the network around 70 °C could be an advantage for biomedical applications, despite the rather poor thermal stability of the furan-functionalized cross-linked polycarbonates.

Divanillin-Based Aromatic Amines: Synthesis and Use as Curing Agents for Fully Vanillin-Based Epoxy Thermosets.

Bio-based aromatic diamines from vanillin substrate were successfully synthesized and characterized. These amines, i.e., methylated divanillylamine (MDVA) and 3,4-dimethoxydianiline (DMAN), were then tested as curing agents for the design of bio-based epoxy thermosets. The epoxy thermosets obtained from these novel vanillin-based amines exhibited promising thermomechanical properties in terms of glass transition temperature and char residue.

Synthesis and Self-Assembly of Xylan-Based Amphiphiles: From Bio-Based Vesicles to Antifungal Properties.

This work aims at designing functional biomaterials through selective chemical modification of xylan from beechwood. Acidic hydrolysis of xylan led to well-defined oligomers with an average of six xylose units per chain and with an aldehyde group at the reductive end. Reductive amination was performed on this aldehyde end group to introduce an azide reactive group. "Click chemistry" was then applied to couple these hydrophilic xylans moieties with different hydrophobic fatty acid methyl esters that were previously functionalized with complementary alkyne functions. The resulting amphiphilic bio-based conjugates were then self-assembled using three different methods, namely, direct solubilization, thin-film rehydration/extrusion, and microfluidics. Well-defined micelles and vesicles were obtained, and their high loading capacity with propiconazole as an antifungal active molecule was shown. The resulting vesicles loaded with propiconazole in a microfluidic process proved to significantly improve the antifungal activity of propiconazole, demonstrating the high potential of such xylan-based amphiphiles.

Extraordinary mechanical performance in disentangled UHMWPE films processed by compression molding.

An approach to obtain disentangled ultra-high molecular weight polyethylene (UHMWPE) films is proposed using a common compression molding. For that, disentangled UHMWPE nascent powders from reactor are processed at temperatures lower than the main melting peak and at high pressure. Then, disentangled UHMWPE films obtained from homogeneous polymerization powders and from those that incorporate SBA-15 mesoporous silica can be easily achieved by this simple methodology. These disentangled UHMWPE based materials show very high crystallinity and, consequently, outstanding elastic modulus and hardness, both further increasing by presence of mesoporous SBA-15 in the hybrids.

Visible-light photocatalyzed oxidative decarboxylation of oxamic acids: a green route to urethanes and ureas.

A sustainable metal-free route to urethanes and ureas based on a photocatalyzed oxidative decarboxylation of oxamic acids is described. The reaction includes in situ generation of an isocyanate from the oxamic acid, using an organic dye as a photocatalyst, a hypervalent iodine reagent as an oxidant and a light source, which trigger the free-radical decarboxylation. This protocol successfully avoids the isolation, purification and storage of carcinogenic isocyanates and allows elaboration of urethanes and ureas in a one-pot process from commercially available sources.

Versatile cross-linked fatty acid-based polycarbonate networks obtained by thiol-ene coupling reaction.

Bio-sourced polycarbonate networks have been synthesized from an alkene-functional fatty-acid based polycarbonate precursor. Cross-linked networks were created using the radical thiol-ene coupling reaction. The resulting polycarbonate materials exhibited versatile properties either influenced by the structure of the cross-linker or the cross-linker/olefin unit ratio. Indeed, the storage modulus above the glass transition temperature could be modulated from 0.9 to 8.9 MPa only by changing the type of cross-linker, i.e. 1,9-nonanedithiol vs. 1,4-benzenedimethanethiol. The cross-linker/olefin unit ratio was also shown to largely impact the polycarbonate networks properties. An elongation at break of nearly 200% was reached when a low cross-linker/olefin ratio was applied. Moreover, functional polycarbonate networks bearing pendant thiol groups were obtained when an excess of dithiol was used with respect to olefin groups.

On the direct use of CO2 in multicomponent reactions: introducing the Passerini four component reaction.

We introduce a novel isocyanide-based multicomponent reaction, the Passerini four component reaction (P-4CR), by replacing the carboxylic acid component of a conventional Passerini three component reaction (P-3CR) with an alcohol and CO2. Key to this approach is the use of a switchable solvent system, allowing the synthesis of a variety of α-carbonate-amides. The reaction was first investigated and optimized using butanol, isobutyraldehyde, tert-butyl isocyanide and CO2. Parameters investigated included the effect of reactant equivalents, reactant concentration, solvent, catalyst, catalyst concentration and CO2 pressure. Of the other parameters, the purity of the aldehyde and its tendency to oxidize was one of the most critical parameters for a successful P-4CR. After optimization, a total of twelve (12) P-4CR compounds were synthesized with conversions ranging between 16 and 82% and isolated yields between 18 and 43%. Their structures were confirmed via 1H and 13C NMR, FT-IR and high resolution mass spectrometry (ESI-MS). In addition, three (3) hydrolysis products of P-4CR (α-hydroxyl-amides) were successfully isolated with yields between 23 and 63% and fully characterized (1H, 13C NMR, FT-IR and ESI-MS) as well.

Simple and Efficient Approach toward Photosensitive Biobased Aliphatic Polycarbonate Materials.

Fatty acids were used as precursors for the synthesis of photosensitive polycarbonate materials. In order to avoid multistep reactions, a simple and straightforward methodology toward the synthesis of photosensitive monomers has been developed. Hence, a fatty acid-based cyclic carbonate bearing an unsaturation was synthesized and subsequently polymerized in a controlled manner (D = 1.07) by organo-catalyzed ring-opening polymerization (ROP). A thio-cinnamate derivative was then readily synthesized via a one-pot reaction and grafted onto the polycarbonate backbone by thiol-ene reaction. The content of photoresponsive cinnamoyl moiety grafted on the polycarbonate was tunable with the reaction time. Such functionalized polycarbonates could be crosslinked (by UV irradiation at 365 nm) and partially decrosslinked (irradiated at 254 nm) and exhibit versatile properties ranging from rather tough materials to elastomeric networks with respect to the content of the photosensitive cinnamoyl moiety grafted on the polymer.

Periodate oxidation of 4-O-methylglucuronoxylans: Influence of the reaction conditions.

This work aims at studying the sodium periodate oxidation of 4-O-methylglucuronoxylans (MGX) in different experimental conditions for a control of the oxidation degree. A series of sodium periodate oxidation reactions were conducted at three NaIO4/xylose molar ratios: 0.05, 0.20 and 1.00. The effects of xylan molar mass, xylan concentration and reaction temperature on the reaction rate have been evaluated by UV/visible spectroscopy at 0.20 NaIO4/xylose ratio. No depolymerization is observed at 0.05 ratio while depolymerization occurs at 0.20 and is even complete at 1.00 NaIO4/xylose ratio. An increase of the reaction temperature - up to 80 °C - leads to an increase of the oxidation rate with no effect on the depolymerization. At high xylan concentrations, the oxidation rate increases but promotes chains aggregation.

From Lignin-derived Aromatic Compounds to Novel Biobased Polymers.

Nowadays, the synthesis of (semi)aromatic polymers from lignin derivatives is of major interest, as aromatic compounds are key intermediates in the manufacture of polymers and lignin is the main source of aromatic biobased substrates. Phenols with a variety of chemical structures can be obtained from lignin deconstruction; among them, vanillin and ferulic acid are the main ones. Depending on the phenol substrates, different chemical modifications and polymerization pathways are developed, leading to (semi)aromatic polymers covering a wide range of thermomechanical properties. This review discusses the synthesis and properties of thermosets (vinyl ester resins, cyanate ester, epoxy, and benzoxazine resins) and thermoplastic polymers (polyesters, polyanhydrides, Schiff base polymers, polyacetals, polyoxalates, polycarbonates, acrylate polymers) prepared from vanillin, ferulic acid, guaiacol, syringaldehyde, or 4-hydroxybenzoic acid.