Improving the routine analysis of siderite for δ13 C and δ18 O in environmental change research.

RATIONALE: The carbon (δ13 C) and oxygen (δ18 O) isotope composition of siderite (FeCO3 ) is used widely to understand and quantify geochemical processes to reconstruct past climate and environmental change. However, few laboratories follow precisely the same protocol for the preparation and analysis of siderite-bearing materials, which combined with the absence of international reference materials and mineral-specific acid fractionation factors, leads potentially to significant differences in isotope data generated by individual laboratories. Here we examine procedures for the isotope analysis of siderite and discuss factors potentially contributing to inconsistencies in sample measurement data. METHODS: Isotope analysis of siderite is first assessed using similar versions of the classical off-line, sealed vessel acid digestion method by comparing data sets obtained from intercomparison materials measured at two participating laboratories. We then compare data from the classical method against those generated using an automated preparation technique using data produced from an independent set of test materials. RESULTS: Measurement of siderite δ13 C is generally both repeatable and reproducible, but measurement of δ18 O may be subject to large (~1‰), method-dependent bias for siderite reacted at differing temperatures (70°C and 100°C) under classical and automated CO2 preparation conditions. The potential for poor oxygen isotope measurement reproducibility is amplified by local differences in sample preparation protocols and procedures used to calibrate measurement data to international reference scales. CONCLUSIONS: We offer suggestions for improving the repeatability and reproducibility of δ13 C and δ18 O analysis on siderite. The challenge of producing consistent isotope data from siderite can only be resolved by ensuring the availability of siderite reference materials to facilitate identical treatment as a basis for minimising method-dependent contributions to data inconsistency between laboratories.

Fish as major carbonate mud producers and missing components of the tropical carbonate factory.

Carbonate mud is a major constituent of recent marine carbonate sediments and of ancient limestones, which contain unique records of changes in ocean chemistry and climate shifts in the geological past. However, the origin of carbonate mud is controversial and often problematic to resolve. Here we show that tropical marine fish produce and excrete various forms of precipitated (nonskeletal) calcium carbonate from their guts ("low" and "high" Mg-calcite and aragonite), but that very fine-grained (mostly < 2 µm) high Mg-calcite crystallites (i.e., > 4 mole % MgCO(3)) are their dominant excretory product. Crystallites from fish are morphologically diverse and species-specific, but all are unique relative to previously known biogenic and abiotic sources of carbonate within open marine systems. Using site specific fish biomass and carbonate excretion rate data we estimate that fish produce ∼6.1 × 10(6) kg CaCO(3)/year across the Bahamian archipelago, all as mud-grade (the < 63 µm fraction) carbonate and thus as a potential sediment constituent. Estimated contributions from fish to total carbonate mud production average ∼14% overall, and exceed 70% in specific habitats. Critically, we also document the widespread presence of these distinctive fish-derived carbonates in the finest sediment fractions from all habitat types in the Bahamas, demonstrating that these carbonates have direct relevance to contemporary carbonate sediment budgets. Fish thus represent a hitherto unrecognized but significant source of fine-grained carbonate sediment, the discovery of which has direct application to the conceptual ideas of how marine carbonate factories function both today and in the past.

Oxygen isotope analysis of carbonates in the calcite-dolomite-magnesite solid-solution by high-temperature pyrolysis: initial results.

Accurate and efficient measurement of the oxygen isotope composition of carbonates (delta(C) (18)O) based on the mass spectrometric analysis of CO(2) produced by reacting carbonate samples with H(3)PO(4) is compromised by: (1) uncertainties associated with fractionation factors (alpha(CO)(2)C) used to correct measured oxygen isotope values of CO(2)(delta(CO(2)(18)O) to delta(C) (18)O; and (2) the slow reaction rates of many carbonates of geological and environmental interest with H(3)PO(4). In contrast, determination of delta(C) (18)O from analysis of CO produced by high-temperature (>1400 degrees C) pyrolytic reduction, using an elemental analyser coupled to continuous-flow isotope-ratio mass spectrometry (TC/EA CF-IRMS), offers a potentially efficient alternative that measures the isotopic composition of total carbonate oxygen and should, therefore, theoretically be free of fractionation effects. The utility of the TC/EA CF-IRMS technique was tested by analysis of carbonates in the calcite-dolomite-magnesite solid-solution and comparing the results with delta(C) (18)O measured by conventional thermal decomposition/fluorination (TDF) on the same materials. Initial results show that CO yields are dependent on both the chemical composition of the carbonate and the specific pyrolysis conditions. Low gas yields (<100% of predicted yield) are associated with positive (>+0.2 per thousand) deviations in delta(C(TC/EA) (18)O compared with delta(C(TDF) (18)O. At a pyrolysis temperature of 1420 degrees C the difference between delta(C) (18)O measured by TC/EA CF-IRMS and TDF (Delta(C(TC/EA,TDF) (18)O) was found to be negatively correlated with gas yield (r = -0.785) and this suggests that delta(C) (18)O values (with an estimated combined standard uncertainty of +/-0.38 per thousand) could be derived by applying a yield-dependent correction. Increasing the pyrolysis temperature to 1500 degrees C also resulted in a statistically significant correlation with gas yield (r = -0.601), indicating that delta(C) (18)O values (with an estimated uncertainty of +/-0.43 per thousand) could again be corrected using a yield-dependent procedure. Despite significant uncertainty associated with TC/EA CF-IRMS analysis, the magnitude of the uncertainty is similar to that associated with the application of poorly defined values of alpha(CO)(2), (C) used to derive delta(C) (18)O from delta(CO(2) (18)O measured by the H(3)PO(4) method for most common carbonate phases. Consequently, TC/EA CF-IRMS could provide a rapid alternative for the analysis of these phases without any effective deterioration in relative accuracy, while analytical precision could be improved by increasing the number of replicate analyses for both calibration standards and samples. Although automated gas preparation techniques based on the H(3)PO(4) method (ISOCARB, Kiel device, Gas-Bench systems) have the potential to measure delta(CO)(2) (18)O efficiently for specific, slowly reacting phases (e.g. dolomite), problems associated with poorly defined alpha(CO)(2), (C) remain. The application of the Principle of Identical Treatment is not a solution to the analysis of these phases because it assumes that a single fractionation factor may be defined for each phase within a solid-solution regardless of its precise chemical composition. This assumption has yet to be tested adequately.