Modelling Inductive Sensors for Arc Fault Detection in Aviation.

Modern aircraft are being equipped with high-voltage and direct current (HVDC) architectures to address the increase in electrical power. Unfortunately, the rise of voltage in low pressure environments brings about a problem with unexpected ionisation phenomena such as arcing. Series arcs in HVDC cannot be detected with conventional means, and finding methods to avoid the potentially catastrophic hazards of these events becomes critical to assure further development of more electric and all electric aviation. Inductive sensors are one of the most promising detectors in terms of sensitivity, cost, weight and adaptability to the circuit wiring in aircraft electric systems. In particular, the solutions based on the detection of the high-frequency (HF) pulses created by the arc have been found to be good candidates in practical applications. This paper proposes a method for designing series arc fault inductive sensors able to capture the aforementioned HF pulses. The methodology relies on modelling the parameters of the sensor based on the physics that intervenes in the HF pulses interaction with the sensor itself. To this end, a comparative analysis with different topologies is carried out. For every approach, the key parameters influencing the HF pulses detection are studied theoretically, modelled with a finite elements method and tested in the laboratory in terms of frequency response. The final validation tests were conducted using the prototypes in real cases of detection of DC series arcs.

Optical Sensing Using Hybrid Multilayer Grating Metasurfaces with Customized Spectral Response.

Customized metasurfaces allow for controlling optical responses in photonic and optoelectronic devices over a broad band. For sensing applications, the spectral response of an optical device can be narrowed to a few nanometers, which enhances its capabilities to detect environmental changes that shift the spectral transmission or reflection. These nanophotonic elements are key for the new generation of plasmonic optical sensors with custom responses and custom modes of operation. In our design, the metallic top electrode of a hydrogenated amorphous silicon thin-film solar cell is combined with a metasurface fabricated as a hybrid dielectric multilayer grating. This arrangement generates a plasmonic resonance on top of the active layer of the cell, which enhances the optoelectronic response of the system over a very narrow spectral band. Then, the solar cell becomes a sensor with a response that is highly dependent on the optical properties of the medium on top of it. The maximum sensitivity and figure of merit (FOM) are SB = 36,707 (mA/W)/RIU and ≈167 RIU-1, respectively, for the 560 nm wavelength using TE polarization. The optical response and the high sensing performance of this device make it suitable for detecting very tiny changes in gas media. This is of great importance for monitoring air quality and thecomposition of gases in closed atmospheres.

Optoelectronic refractometric sensing device for gases based on dielectric bow-ties and amorphous silicon solar cells.

The transformation of an hydrogenated amorphous silicon solar cell (aSiH) into an optoelectronic refratometric sensor has been possible through the addition of dielectric bow-tie resonant structures. The indium transparent oxide top electrode is replaced by a thin metallic layer to selectively prevent the direct transmission of light to the active layer of the cell. Then, an array of dielectric bow-tie structures is placed on top of this electrode, to activate the optical absorption through surface plasmon resonance (SPR). The whole device is exposed to the analyte under measure, which is the surrounding medium. Three different dielectric materials with low, medium, and high refractive index were selected for the bow-ties, namely magnesium fluoride (MgF[Formula: see text]), silicon dioxide (SiO[Formula: see text]), and aluminum nitride (AlN) have been tested as coupling structure for SPR excitation. The maximization of the readout/short circuit current has been achieved through the geometrical parameters of such structure. We have selected the geometrical parameters to maximize the short circuit current delivered by the a-Si cell at a given selected wavelength. The design has been customized to gas measurements application, where the index of refraction is slightly above 1 around 10[Formula: see text]. Our analysis reveals ultra-high sensitivity of [Formula: see text] (mA/W)/RIU, and a figure of merit FOM= 107 RIU[Formula: see text], when the bow-tie is made of SiO[Formula: see text]. A performance rally competitive with those previously reported in literature, with the additional advantage of circunventing both moving parts and spectral interrogation elements.

Computational and Experimental Analysis of Gold Nanorods in Terms of Their Morphology: Spectral Absorption and Local Field Enhancement.

A nanoparticle's shape and size determine its optical properties. Nanorods are nanoparticles that have double absorption bands associated to surface plasmon oscillations along their two main axes. In this work, we analize the optical response of gold nanorods with numerical simulations and spectral absorption measurements to evaluate their local field enhancement-which is key for surface-enhanced Raman spectroscopic (SERS) applications. Our experimental results are in good agreement with finite element method (FEM) simulations for the spectral optical absorption of the nanoparticles. We also observed a strong dependence of the optical properties of gold nanorods on their geometrical dimension and shape. Our numerical simulations helped us reveal the importance of the nanorods' morphology generated during the synthesis stage in the evaluation of absorption and local field enhancement. The application of these gold nanorods in surface-enhancement Raman spectroscopy is analyzed numerically, and results in a 5.8×104 amplification factor when comparing the values obtained for the nanorod deposited on a dielectric substrate compared to the nanorod immersed in water.

Resonant nano-dimer metasurface for ultra-thin a-Si:H solar cells.

Low-cost hydrogenated amorphous silicon solar cells (a-Si:H) can perform better and be more competitive by including nanostructures. An optimized nano-dimer structure embedded in close contact with the back electrode of an aSi:H ultra-thin solar cells can enhance the deliverable short-circuit current up to 27.5 %. This enhancement is the result of an increase in the absorption at the active layer, that is the product of an efficient scattering from the nanostructure. From our calculations, the nano-dimer structure must be made out of a high-index of refraction material, like GaP. The evaluation of the scattering and absorption cross section of the structure supports the calculated enhancement in short-circuit current, that is always accompanied by a decrease in the total reflectance of the cell, which is reduced by about 50 %.

Enabling selective absorption in perovskite solar cells for refractometric sensing of gases.

Perovskite solar cells are currently considered a promising technology for solar energy harvesting. Their capability to deliver an electrical signal when illuminated can sense changes in environmental parameters. We have numerically analyzed the variation of the current delivered by a perovskite cell as a function of the index of refraction of air, that is in contact with the front surface of the cell. This calculation identifies which geometrical and material structures enhance this behavior. After replacing the top transparent electrode of a solar cell by an optimized subwavelength metallic grating, we find a large variation in the responsivity of the cell with respect to the change in the index of refraction of the surrounding medium. Such a refractometric sensor can be interrogated electronically, avoiding the cumbersome set-ups of spectral or angular interrogation methods. We present an adaptation of the performance parameters of refractometric sensors (sensitivity and figure of merit) to the case of opto-electronic interrogation methods. The values of sensitivity and Figure of Merit are promising for the development of refractometric perovskite-based sensors.

Numerical model of the inhomogeneous scattering by the human lens.

We present in this work a numerical model for characterizing the scattering properties of the human lens. After analyzing the scattering properties of two main scattering particles actually described in the literature through FEM (finite element method) simulations, we have modified a Monte Carlo's bulk scattering algorithm for computing ray scattering in non-sequential ray tracing. We have implemented this ray scattering algorithm in a layered model of the human lens in order to calculate the scattering properties of the whole lens. We have tested our algorithm by simulating the classic experiment carried out by Van der Berg et al for measuring "in vitro" the angular distribution of forward scattered light by the human lens. The results show the ability of our model to simulate accurately the scattering properties of the human lens.

Detection of Histamine Dihydrochloride at Low Concentrations Using Raman Spectroscopy Enhanced by Gold Nanostars Colloids.

In this paper, we report a fast and easy method to detect histamine dihydrochloride using gold nanostars in colloidal aqueous solution as a highly active SERS platform with potential applications in biomedicine and food science. This colloid was characterized with SEM and UV⁻Vis spectroscopy. Also, numerical calculations were performed to estimate the plasmonic resonance and electric field amplification of the gold nanoparticles to compare the difference between nanospheres and nanostars. Finally, aqueous solutions of histamine dihydrochloride were prepared in a wide range of concentrations and the colloid was added to carry out SERS. We found SERS amplified the Raman signal of histamine by an enhancement factor of 1 . 0 × 10 7 , demonstrating the capability of the method to detect low concentrations of this amine molecule.

Plasmonic Sensor Based on Dielectric Nanoprisms.

A periodic array of extruded nanoprisms is proposed to generate surface plasmon resonances for sensing applications. Nanoprisms guide and funnel light towards the metal-dielectric interface where the dielectric acts as the medium under test. The system works under normal incidence conditions and is spectrally interrogated. The performance is better than the classical Kretschmann configurations, and the values of sensitivity and figure of merit are competitive with other plasmonic sensor technologies. The geometry and the choice of materials have been made taking into account applicable fabrication constraints.

Selective Dielectric Metasurfaces Based on Directional Conditions of Silicon Nanopillars.

Dielectric metasurfaces based on high refractive index materials have been proposed recently. This type of structure has several advantages over their metallic counterparts. In this work, we demonstrate that dielectric metasurfaces can be theoretically designed satisfying Kerker's zero-forward condition. This is the first time that a dielectric metasurface based on this principle has been designed. A selective dielectric metasurface of silicon nanopillars is designed to work at 632.8 nm. This structure could work both as a dielectric mirror and a reject band filter. Furthermore, by scaling up the structure, it could be possible to manufacture a terahertz (THz) dielectric mirror.

Spectral Response of Metallic Optical Antennas Driven by Temperature.

When optical antennas are used as light detectors, temperature changes their spectral response. Using this relation, we determine the spectrum of a light beam from an optical antenna's signal. A numerical evaluation of the temperature-spectral response has been completed with a model for the noise of the device. Using both the response and the noise model, we have established the capabilities of the device by quantifying the error in the spectrum determination both for broadband spectrum and monochromatic radiation.

Polarimetric pixel using Seebeck nanoantennas.

Optical nanoantennas made of two metals are proposed to produce a Seebeck voltage proportional to the Stokes parameters of a light beam. The analysis is made using simulations in the electromagnetic and thermal domains. Each Stokes parameter is independently obtained from a dedicated nanoantenna configuration. S1 and S2 rely on the combination of two orthogonal dipoles. S3 is given by arranging two Archimedian spirals with opposite orientations. The analysis also includes an evaluation of the error associated with the Seebeck voltage, and the crosstalk between Stokes parameters. The results could lead to the conception of polarization sensors having a receiving area smaller than 10λ(2). We illustrate these findings with a design of a polarimetric pixel.

Steerable optical antennas by selective heating.

Directional steerability can be obtained for an array of optical antennas through selective heating of the individual elements. Heating changes electrical conductivity of the heated element, which affects the phase of the generated currents. The variation in temperature can be obtained by modifying the biasing point of the individual elements of the array, which would allow fast reconfiguration. The numerical evaluation of the performance of an array of a reduced number of antennas (2 and 3) shows the feasibility of this approach.

Seebeck nanoantennas for the detection and characterization of infrared radiation.

Arrays of metallic thermocouples in the shape of spiral nanoantennas are proposed as infrared detectors, which use the thermoelectric properties of the metallic interfaces to generate electrical DC signals. The responsivity of these types of antennas is evaluated from both theoretical and numerical perspectives pointing out its potential as infrared sensors. Moreover, the same structures can be used to characterize the state of polarization of the optical near fields with a spatial resolution comparable to the wavelength.

Robustness of antenna-coupled distributed bolometers.

This Letter shows the effect of the geometrical and material properties of lead lines and connections on the robustness and reliability of optical antennas working as distributed bolometers. We analyze the operational limits of the biasing voltage using a mutiphysics finite element method. We demonstrate that, after evaluating the effect of the electromagnetic irradiance falling on the device, biasing voltage is the main limiting factor to maintain operative titanium optical antennas. Results have been experimentally verified by finding the biasing values needed to destroy optical antennas working as distributed bolometers. Structural damage has been identified from scanning electron microscopy images.

Antenna array connections for efficient performance of distributed microbolometers in the IR.

Optical antennas and resonant structures have been extensively investigated due to its potential for electromagnetic detection and energy harvesting applications. However their integration into large arrays and the role of connection lines between individual antennas has drawn little attention. This is necessary if we want to exploit its potential constructively and to enable economical large-scale fabrication. In this contribution we point out some features that an efficient antenna array should address. Experimental measurements on aluminum microbolometers are compared to electromagnetic simulations, it is shown that the finite size of a real array and the interconnection lines interact and affect the global performance.