Highly efficient p-i-n perovskite solar cells that endure temperature variations.

Daily temperature variations induce phase transitions and lattice strains in halide perovskites, challenging their stability in solar cells. We stabilized the perovskite black phase and improved solar cell performance using the ordered dipolar structure of ß-poly(1,1-difluoroethylene) to control perovskite film crystallization and energy alignment. We demonstrated p-i-n perovskite solar cells with a record power conversion efficiency of 24.6% over 18 square millimeters and 23.1% over 1 square centimeter, which retained 96 and 88% of the efficiency after 1000 hours of 1-sun maximum power point tracking at 25° and 75°C, respectively. Devices under rapid thermal cycling between -60° and +80°C showed no sign of fatigue, demonstrating the impact of the ordered dipolar structure on the operational stability of perovskite solar cells.

Slot-Die Coated Triple-Halide Perovskites for Efficient and Scalable Perovskite/Silicon Tandem Solar Cells.

Wide bandgap halide perovskite materials show promising potential to pair with silicon bottom cells. To date, most efficient wide bandgap perovskites layers are fabricated by spin-coating, which is difficult to scale up. Here, we report on slot-die coating for an efficient, 1.68 eV wide bandgap triple-halide (3halide) perovskite absorber, (Cs0.22FA0.78)Pb(I0.85Br0.15)3 + 5 mol % MAPbCl3. A suitable solvent system is designed specifically for the slot-die coating technique. We demonstrate that our fabrication route is suitable for tandem solar cells without phase segregation. The slot-die coated wet halide perovskite is dried by a "nitrogen (N2)-knife" with high reproducibility and avoiding antisolvents. We explore varying annealing conditions and identify parameters allowing crystallization of the perovskite film into large grains reducing charge collection losses and enabling higher current density. At 150 °C, an optimized trade-off between crystallization and the PbI2 aggregates on the film's top surface is found. Thus, we improve the cell stability and performance of both single-junction cells and tandems. Combining the 3halide top cells with a 120 µm thin saw damage etched commercial Czochralski industrial wafer, a 2-terminal monolithic tandem solar cell with a PCE of 25.2% on a 1 cm2 active area is demonstrated with fully scalable processes.

Biological/metal oxide composite transport layers cast from green solvents for boosting light harvesting response of organic photovoltaic cells indoors.

Organic solar cells with biological/metal-oxide electron transport layers (ETLs), consisting of a ZnO compact layer covered by a thin DNA layer, both of which deposited with green solvents (water or water/alcohols mixtures) are presented for application under low intensity indoor lighting. Under white LED lamp (200, 400 lx), photovoltaic cells with P3HT:PC70BM polymer semiconductor blends delivered an average maximum power density (MPD) of 8.7µW cm-2, corresponding to a power conversion efficiency, PCE, of = 8.56% (PCE of best cell was 8.74%). The ZnO/DNA bilayer boosted efficiency by 68% and 13% in relative terms compared to cells made with DNA-only and ZnO-only ETLs at 400 lx. Photovoltaic cells with ZnO/DNA composite ETLs based on PTB7:PC70BM blends, that absorb a broader range of the indoor lighting spectrum, delivered MPDs of 16.2µW cm-2with an estimated average PCE of 14.3% (best cell efficiency of 15.8%) at 400 lx. The best efficiencies for cells fabricated on flexible plastic substrates were 11.9% at 400 lx. This is the first report in which polymer photovoltaics incorporating biological materials have shown to increment performance at these low light levels and work very efficiently under indoor artificial light illumination. The finding can be useful for the production of more bio-compatible photovoltaics as well as bio-sensing devices based on organic semiconductors.

Encapsulation and Outdoor Testing of Perovskite Solar Cells: Comparing Industrially Relevant Process with a Simplified Lab Procedure.

Perovskite solar cells (PSCs) have shown great potential for next-generation photovoltaics. One of the main barriers to their commercial use is their poor long-term stability under ambient conditions and, in particular, their sensitivity to moisture and oxygen. Therefore, several encapsulation strategies are being developed in an attempt to improve the stability of PSCs in a humid environment. The lack of common testing procedures makes the comparison of encapsulation strategies challenging. In this paper, we optimized and investigated two common encapsulation strategies: lamination-based glass-glass encapsulation for outdoor operation and commercial use (COM) and a simple glue-based encapsulation mostly utilized for laboratory research purposes (LAB). We compare both approaches and evaluate their effectiveness to impede humidity ingress under three different testing conditions: on-shelf storage at 21 °C and 30% relative humidity (RH) (ISOS-D1), damp heat exposure at 85 °C and 85% RH (ISOS-D3), and outdoor operational stability continuously monitoring device performance for 10 months under maximum power point tracking on a roof-top test site in Berlin, Germany (ISOS-O3). LAB encapsulation of perovskite devices consists of glue and a cover glass and can be performed at ambient temperature, in an inert environment without the need for complex equipment. This glue-based encapsulation procedure allowed PSCs to retain more than 93% of their conversion efficiency after 1566 h of storage in ambient atmosphere and, therefore, is sufficient and suitable as an interim encapsulation for cell transport or short-term experiments outside an inert atmosphere. However, this simple encapsulation does not pass the IEC 61215 damp heat test and hence results in a high probability of fast degradation of the cells under outdoor conditions. The COM encapsulation procedure requires the use of a vacuum laminator and the cells to be able to withstand a short period of air exposure and at least 20 min at elevated temperatures (in our case, 150 °C). This encapsulation method enabled the cells to pass the IEC 61215 damp heat test and even to retain over 95% of their initial efficiency after 1566 h in a damp heat chamber. Above all, passing the damp heat test for COM-encapsulated devices translates to devices fully retaining their initial efficiency for the full duration of the outdoor test (>10 months). To the best of the authors' knowledge, this is one of the longest outdoor stability demonstrations for PSCs published to date. We stress that both encapsulation approaches described in this work are useful for the scientific community as they fulfill different purposes: the COM for the realization of prototypes for long-term real-condition validation and, ultimately, commercialization of perovskite solar cells and the LAB procedure to enable testing and carrying out experiments on perovskite solar cells under noninert conditions.

Stability Assessment of p-i-n Perovskite Photovoltaic Mini-Modules Utilizing Different Top Metal Electrodes.

Long-term stability is one of the major challenges for p-i-n type perovskite solar modules (PSMs). Here, we demonstrate the fabrication of fully laser-patterned series interconnected p-i-n perovskite mini-modules, in which either single Cu or Ag layers are compared with Cu/Au metal-bilayer top electrodes. According to the scanning electron microscopy measurements, we found that Cu or Ag top electrodes often exhibit flaking of the metal upon P3 (top contact removal) laser patterning. For Cu/Au bilayer top electrodes, metal flaking may cause intermittent short-circuits between interconnected sub-cells during operation, resulting in fluctuations in the maximum power point (MPP). Here, we demonstrate Cu/Au metal-bilayer-based PSMs with an efficiency of 18.9% on an active area of 2.2 cm2 under continuous 1-sun illumination. This work highlights the importance of optimizing the top-contact composition to tackle the operational stability of mini-modules, and could help to improve the feasibility of large-area module deployment for the commercialization of perovskite photovoltaics.

Compositional and Interfacial Engineering Yield High-Performance and Stable p-i-n Perovskite Solar Cells and Mini-Modules.

Through the optimization of the perovskite precursor composition and interfaces to selective contacts, we achieved a p-i-n-type perovskite solar cell (PSC) with a 22.3% power conversion efficiency (PCE). This is a new performance record for a PSC with an absorber bandgap of 1.63 eV. We demonstrate that the high device performance originates from a synergy between (1) an improved perovskite absorber quality when introducing formamidinium chloride (FACl) as an additive in the "triple cation" Cs0.05FA0.79MA0.16PbBr0.51I2.49 (Cs-MAFA) perovskite precursor ink, (2) an increased open-circuit voltage, VOC, due to reduced recombination losses when using a lithium fluoride (LiF) interfacial buffer layer, and (3) high-quality hole-selective contacts with a self-assembled monolayer (SAM) of [2-(9H-carbazol-9-yl)ethyl]phosphonic acid (2PACz) on ITO electrodes. While all devices exhibit a high performance after fabrication, as determined from current-density voltage, J-V, measurements, substantial differences in device performance become apparent when considering longer-term stability data. A reduced long-term stability of devices with the introduction of a LiF interlayer is compensated for by using FACl as an additive in the metal-halide perovskite thin-film deposition. Optimized devices maintained about 80% of the initial average PCE during maximum power point (MPP) tracking for >700 h. We scaled the optimized device architecture to larger areas and achieved fully laser patterned series-interconnected mini-modules with a PCE of 19.4% for a 2.2 cm2 active area. A robust device architecture and reproducible deposition methods are fundamental for high performance and stable large-area single junction and tandem modules based on PSCs.

Coating ZnO nanoparticle films with DNA nanolayers for enhancing the electron extracting properties and performance of polymer solar cells.

Here we present for the first time polymer solar cells that incorporate biological material that show state of the art efficiencies in excess of 8%. The performance of inverted polymer solar cells was improved significantly after deposition of ZnO nanoparticles (ZnO-NPs) together with a thin deoxyribonucleic acid nanolayer and used as an electron extraction layer (EEL). The ZnO-NPs/DNA double layer improved the rectifying ratio, shunt resistance of the cells as well as lowering the work function of the electron-collecting contact. Importantly, the ZnO-NPs/DNA bilayer enhanced the power conversion efficiency of cells considerably compared to cells with EELs made of only DNA (improvement of 56% in relative terms) or only ZnO-NPs (improvement of 19% in relative terms) reaching a best power conversion efficiency of 8.5%. The ZnO-NPs/DNA double layer cells also outperformed ones made with one of the most efficient previous synthetic composite EELs (i.e. ZnO/PEIE(poly(ethyleneimine)-ethoxylated)). Since all fabrication procedures were carried out at low (<150 °C) or room temperature, we have applied the findings to flexible substrates as well as on glass obtaining a high PCE of 7.2%. The solar cells with the biological/metal-oxide composite EELs also delivered an improvement in the stability (∼20% in relative term) compared to that with ZnO-NPs only. All these findings show that natural materials, in this case DNA, the premium biological material, can be incorporated in organic semiconductor devices in tandem with inorganic devices delivering uncompromising levels of performance as well as significant improvements.