A surface plasmon resonance nanostructure containing graphene and BaTiO3 layers for sensitive defection of organic compounds.

Organic compound-based sensors are used in a variety of significant fields, including medical research, azeotropic calibration, vegetable oil extraction, the shoe industry and geothermal power plants. Here, a high-performance, two-dimensional material-based organic compound sensor has been proposed using a surface plasmon resonance (SPR) nanostructure consisting of a BK7 glass prism, Ag, BaTiO3, Ag, graphene and sensing layer. The reflectivity curves of the SPR device have been investigated when the sensing media are Pentane, n-Hexane, n-Heptane and n-Octane. The thickness of the BaTiO3 layer and the number of graphene sheets have been optimized to maximize the sensitivity. The highest sensitivity attained is 220.83 deg/RIU for n-Octane with 45 nm silver/10 nm BaTiO3/8 nm silver and four layers of graphene. We believe that the SPR-based sensors are simple and can replace the spectrometry, chromatography and electrochemical based sensors. The proposed design is extremely effective for diverse applications in biological, industrial and chemical detection because of its simple structure and great performance.

Detection of Virus SARS-CoV-2 Using a Surface Plasmon Resonance Device Based on BiFeO3-Graphene Layers.

Coronavirus disease (COVID-19) pandemic outbreak is being investigated by severe respirational syndrome coronavirus-2 (SARS-CoV-2) as a global health issue. It is crucial to propose sensitive and rapid coronavirus detectors. Herein, we propose a biosensor based on surface plasmon resonance (SPRE) for the detection of SARS-CoV-2 virus. To achieve improved sensitivity, a BiFeO3 layer is inserted between a metal (Ag) thin film and a graphene layer in the proposed SPRE device so that it has the structure BK7 prism/ Ag/ BiFeO3/ graphene/ analyte. It has been demonstrated that a small variation in the refractive index of the analyte can cause a considerable shift in the resonance angle caused by the remarkable dielectric properties of the BiFeO3 layer, which include a high index of refraction and low loss. The proposed device has shown an extremely high sensitivity of 293 deg/RIU by optimizing the thicknesses of Ag, BiFeO3, and the number of graphene sheets. The proposed SPRE-based sensor is encouraging for use in various sectors of biosensing because of its high sensitivity.

A Novel Design of Complementary Split Ring Resonator Metamaterial-Based Low-Profile MIMO Antenna with Defected Ground Structure for S/C/X/Ka Band Applications.

The article represents the design of two port-based printed MIMO antenna structures that have the advantages of low profile, simple structure, good isolation, peak gain, directive gain, and reflection coefficient. The performance characteristics are observed for the four design structures by cropping the patch region, loading the slits near the hexagonal-shaped patch, and adding and removing the slots in the ground area. The antenna provides a least reflection coefficient of -39.44 dB, a maximum electric field of patch region of 33.3 V/cm, a total gain of 5.23 dB, and good values of total active reflection coefficient and diversity gain. The proposed design provides nine bands' response, a peak bandwidth of 2.54 GHz, and a peak bandwidth of 26.127 dB. The four proposed structures are fabricated using a low-profile material to support mass production. The comparison among simulated and fabricated structures is included to check the authenticity of the work. The performance assessment of the proposed design with other published articles is carried out for the performance observation. The suggested technique is analyzed over the wideband of frequency region 1 GHz to 14 GHz. The multiple band responses make the proposed work suitable for wireless applications in S/C/X/Ka bands.

Design and Fabrication of Compact, Multiband, High Gain, High Isolation, Metamaterial-Based MIMO Antennas for Wireless Communication Systems.

We proposed a novel approach based on a complementary split-ring resonator metamaterial in a two-port MIMO antenna, giving high gain, multiband results with miniature size. We have also analyzed a circular disk metasurface design. The designs are also defected using ground structure by reducing the width of the ground plane to 8 mm and etching all other parts of the ground plane. The electric length of the proposed design is 0.5λ × 0.35λ × 0.02λ. The design results are also investigated for a different variation of complementary split-ring resonator ring sizes. The inner and outer ring diameters are varied to find the optimized solution for enhanced output performance parameters. Good isolation is also achieved for both bands. The gain and directivity results are also presented. The results are compared for isolation, gain, structure size, and the number of ports. The compact, multiband, high gain and high isolation design can apply to WiMAX, WLAN, and satellite communication applications.

Design and Fabrication of a Low-Cost, Multiband and High Gain Square Tooth-Enabled Metamaterial Superstrate Microstrip Patch Antenna.

The manuscript represents a novel square tooth-enabled superstrate metamaterial loaded microstrip patch antenna for the multiple frequency band operation. The proposed tooth-based metamaterial antenna provides better gain and directivity. Four antenna structures are numerically investigated for the different geometry of the patch and tooth. These proposed structures are simulated, fabricated, measured, and compared for the frequency range of 3 GHz to 9 GHz. The electrical equivalent model of the split-ring resonator is also analyzed in the manuscript. The comparative analysis of all of the proposed structures has been carried out, in terms of several bands, reflectance response, VSWR, gain and bandwidth. The results are compared with previously published works. The effects are simulated using a high-frequency structure simulator tool with the finite element method. The measured and fabricated results are compared for verification purposes. The proposed structure provides seven bands of operation and 8.57 dB of gain. It is observed that the proposed design offers the multiple frequency band operation with a good gain. The proposed tooth-based metamaterial antenna suits applications, such as the surveillance radar, satellite communication, weather monitoring and many other wireless devices.

Optical Detection of Fat Concentration in Milk Using MXene-Based Surface Plasmon Resonance Structure.

MXene (Ti3C2Tx) has emerged very recently as an interacting material for surface plasmon resonance (SPR) configuration. It was discovered that Ti3C2Tx can facilitate the adsorption of biomolecules due to its higher binding energies, stronger interaction between matter and light, and larger surface area. In this work, a two-dimensional Ti3C2Tx and silicon layer-based SPR refractometric sensor is proposed for the sensitive and fast detection of milk fat concentration due to the high significance of this issue to people all over the world. The proposed SPR structure employs BK7 (BK7 is a designation for the most common Borosilicate Crown glass used for a variety of applications in the visible range) as a coupling prism and silver as a metal layer. The layer thicknesses and the number of Ti3C2Tx sheets are optimized for the highest performance. The highest reached sensitivity is 350 deg./RIU with 50 nm silver and 4 nm silicon with a monolayer of Ti3C2Tx, which is ultra-high sensitivity compared to the latest work that utilizes SPR configuration. The proposed SPR-based sensor's ultra-high sensitivity makes it more attractive for usage in a variety of biosensing applications.

Surface plasmon resonance biosensor based on graphene layer for the detection of waterborne bacteria.

As a result of the risks that waterborne bacteria bring to the human body, identifying them in drinking water has become a global concern. In this article, a highly sensitive surface plasmon resonance (SPR) biosensor consisting of prism, Ag, graphene, affinity layer and sensing medium is proposed for rapid detection of the waterborne bacteria. Four SPR-based sensors are first studied with the structures prism/Ag/sensing medium, prism/Ag/affinity layer/sensing medium, prism/Ag/graphene/sensing medium, and prism/Ag/graphene/affinity layer/sensing medium. The latter structure is found to have the highest sensitivity so it is considered for further investigations. Four different commonly used prisms are then demonstrated which are N-FK51A, 2S2G, SF10 and BK7. The structure with the prism N-FK51A is found to correspond to the highest sensitivity so it is considered for further investigations. The structure parameters are then optimized. The proposed SPR sensor can achieve high sensitivity of about 221.63 °/RIU for Escherichia coli and 178.12 °/RIU for Vibrio cholera bacteria with an average value of 199.87 °/RIU. We believe that the proposed structure will open a new window in the field of microorganism detections.