Quantitative ultrahigh-molecular-weight polyethylene wear in total elbow retrievals.

BACKGROUND: The purpose of this study was to evaluate ultrahigh-molecular-weight polyethylene (UHMWPE) wear and damage from retrieved total elbow arthroplasty components and compare in vivo wear with wear produced in vitro. METHODS: Explanted total elbow components were collected at revision surgery. UHMWPE damage was characterized visually, whereas penetration and wear were quantified using micro-computed tomography and gas pycnometry. Volumetric wear rates were compared with historical hip data, and wear data were compared with reported in vitro wear test data. RESULTS: Humeral bushing damage primarily occurred in the form of burnishing, scratching, and pitting at the articular face in the region of contact with the ulnar component. Wear of the ulnar bushings was concentrated on the edge of the component at the point of contact with the axis pin. Pitting and embedded debris were dominant damage modes, in addition to burnishing and delamination. Backside wear was negligible. The median linear penetration rates of the lateral, medial, and ulnar bushings were 0.14 mm/yr (range, 0.01-0.78 mm/yr), 0.12 mm/yr (range, 0.03-0.55 mm/yr), and 0.11 mm/yr (range, 0.01-0.69 mm/yr), respectively. The volumetric wear rates of the lateral, medial, and ulnar bushings were 5.5 mm3/yr (range, 0.7-37.2 mm3/yr), 5.9 mm3/yr (range, 0.6-25.5 mm3/yr), and 5.5 mm3/yr (range, 1.2-51.2 mm3/yr), respectively. CONCLUSIONS: The observed wear rates were similar to those reported in well-functioning total hip replacement patients with conventional UHMWPE bearings. We found limitations in reported in vitro testing resulting in wear that was not consistent with our retrieval data. We recommend further investigation to clinically validate in vitro simulation to provide appropriate loading protocols for elbow wear simulation.

Is There A Difference in Bone Ingrowth in Modular Versus Monoblock Porous Tantalum Tibial Trays?

Contemporary total knee designs incorporating highly porous metallic surfaces have demonstrated promising clinical outcomes. However, stiffness differences between modular and monoblock porous tantalum tibial trays may affect bone ingrowth. This study investigated effect of implant design, spatial location and clinical factors on bone ingrowth. Three modular and twenty-one monoblock retrieved porous tantalum tibial trays were evaluated for bone ingrowth. Nonparametric statistical tests were used to investigate differences in bone ingrowth by implant design, tray spatial location, substrate depth and clinical factors. Modular trays (5.3 ± 3.2%) exhibited higher bone ingrowth than monoblock trays (1.6 ± 1.9%, P = 0.032). Bone ingrowth in both designs was highest in the initial 500 µm from the surface. Implantation time was positively correlated with bone ingrowth for monoblock trays.

Use of reverse total shoulder arthroplasty in the Medicare population.

BACKGROUND: Reverse shoulder arthroplasty (RSA) has been Food and Drug Administration approved in the United States since 2004 but did not obtain a unique code until 2010. Therefore, the use of this popular procedure has yet to be reported. The purpose of this study was to examine the use and reimbursement of RSA compared with total shoulder arthroplasty (TSA) and shoulder hemiarthroplasty (SHA). METHODS: We analyzed the 100% sample of the 2011 Medicare Part A claims data for patients aged 65 years or older. Patient demographic characteristics, diagnoses, provider information, reimbursements, and lengths of stay were extracted from the claims data. RESULTS: In 2011, a total of 31,002 shoulder arthroplasty procedures were performed; 37% were RSAs, 42% were TSAs, and 21% were SHAs. Osteoarthritis was the primary diagnosis code in 91% of TSAs, 37% of SHAs, and 45% of RSAs. A primary diagnosis of osteoarthritis with no secondary code for rotator cuff tear was found in 22% of patients undergoing RSA. The mean length of stay for RSA (2.6 days; SD, 2.1 days) was longer than that for TSA (2.1 days; SD, 1.5 days) and shorter than that for SHA (3.5 days; SD, 3.6 days) (P < .001). Lower-volume surgeons (<10 arthroplasties per year) performed most shoulder arthroplasties: 57% of RSAs, 65% of TSAs, and 97% of SHAs. Seventy percent of RSAs were implanted by surgeons who performed more RSAs than TSAs and SHAs combined. CONCLUSIONS: RSA is performed with similar frequency to TSA and almost twice as much as SHA in the Medicare population. Lower-volume surgeons perform most RSAs, and a majority of surgeons perform more RSAs than all anatomic shoulder arthroplasties combined.

Risk of venous thromboembolism after shoulder arthroplasty in the Medicare population.

BACKGROUND: Chemoprophylaxis for venous thromboembolism (VTE) is considered standard of care after lower but not after upper extremity arthroplasty. Medicare claims data were analyzed to determine the national incidence of symptomatic VTE after shoulder arthroplasty during the index surgical admission and after discharge. METHODS: Incidence of VTE was compared between shoulder arthroplasty and lower extremity arthroplasty, and patient-specific risk factors for pulmonary embolism were determined for shoulder arthroplasty. Finally, the incidence of surgical site bleeding was determined for each type of procedure. RESULTS: VTE complications occurred in 1.2% of lower extremity and 0.53% of shoulder arthroplasties. Patient factors that were associated with an increased risk of VTE included a principal diagnosis of fracture, history of VTE, cardiac arrhythmia, presence of a metastatic tumor, coagulopathy, congestive heart failure, alcohol abuse, and obesity. Adjusted rates of VTE were generally higher for lower extremity compared with shoulder arthroplasties. Prevalence of readmission for VTE was higher for shoulder hemiarthroplasty than for total shoulder arthroplasty. Wound hematoma rates were similar between shoulder and lower extremity procedures. CONCLUSIONS: VTE rates after shoulder arthroplasty were generally lower than those after lower extremity arthroplasty. We believe that the risk of bleeding combined with the lower rates of VTE with existing lower rates of chemoprophylaxis does not warrant the routine use of anticoagulation. Use of mechanical prophylaxis combined with aspirin may be sufficient for shoulder arthroplasty patients who are not at increased risk of VTE. Chemoprophylaxis with agents other than aspirin may be warranted in patients with a demonstrated risk of VTE.

Is there material loss at the backside taper in modular CoCr acetabular liners?

BACKGROUND: Metal wear and corrosion products generated by hip replacements have been linked to adverse local tissue reactions. Recent investigations of the stem/head taper junction have identified this modular interface as another possible source of metal debris; however, little is known regarding other modular metallic interfaces, their ability to produce metal debris, and possibly to provide insight in the mechanisms that produce metal debris. QUESTIONS/PURPOSES: We asked three questions: (1) can we develop a reliable method to estimate volumetric material loss from the backside taper of modular metal-on-metal liners, (2) do backside tapers of modular metal-on-metal liners show a quantifiable volumetric material loss, and, if so, (3) how do regions of quantitatively identified material loss correspond to visual and microscopic investigations of surface damage? METHODS: Twenty-one cobalt-chromium (CoCr) liners of one design and manufacturer were collected through an institutional review board-approved retrieval program. All liners were collected during revision surgeries, where the primary revision reason was loosening (n=11). A roundness machine measured 144 axial profiles equally spaced about the circumference of the taper region near the rim to estimate volume and depth of material loss. Sensitivity and repeatability analyses were performed. Additionally, visual and scanning electron microscopy investigations were done for three liners. RESULTS: Our measurement method was found to be reproducible. The sensitivity (how dependent measurement results are on experimental parameters) and repeatability (how consistent results are between measurements) analyses confirmed that component alignment had no apparent effect (weak correlation, R2=0.04) on estimated volumetric material loss calculations. Liners were shown to have a quantifiable material loss (maximum=1.7 mm3). Visual investigations of the liner surface could identify pristine surfaces as as-manufactured regions, but could misidentify discoloration as a possible region of material loss. Scanning electron microscopy more accurately distinguished between as-manufactured and damaged regions of the taper. CONCLUSIONS: The roundness machine has been used to develop a repeatable method for characterizing material loss; future work comparing a gravimetric standard with estimations of material loss determined from the roundness machine may show the accuracy and effectiveness of this method. Liners show rates of material loss that compare with those reported for other taper junctions. Visual inspection alone may misidentify as-manufactured regions as regions of material loss. CLINICAL RELEVANCE: This study identifies the acetabular liner/shell interface in modular metal-on-metal devices as a potential source of metal wear or corrosion products. The relation between metal debris and clinical performance, regardless of the type of bearing couple, is a concern for clinicians. Therefore, it is important to characterize every type of modular junction to understand the quantity, location, and mechanism(s) of material loss.

Characterization of wear debris in total elbow arthroplasty.

BACKGROUND: The purpose of this study was to evaluate wear debris in periprosthetic tissues at the time of revision total elbow arthroplasty. Polyethylene, metallic, and bone cement debris were characterized, and the tissue response was quantified. MATERIALS AND METHODS: Capsular and medullary tissue samples were collected during revision surgery. Polyethylene debris was characterized by scanning electron microscopy after tissue digestion. The concentrations of metal and cement debris were quantified by inductively coupled plasma mass spectrometry. Tissue response was graded with a semiquantitative histologic method. RESULTS: Polyethylene particle size varied from the submicron range to over 100 µm. The mean diameter ranged from 0.6 µm to about 1 µm. Particles in the synovial tissues were larger and less abundant than those in tissues from the medullary canal. Cement, titanium alloy, and low levels of cobalt-chrome debris were also present, with cement predominating over metal debris. Histiocyte response was associated with small polyethylene particles (0.5-2 µm), and giant cells were associated with large polyethylene particles (>2 µm). Histiocyte scores positively correlated with the polyethylene particle number and the presence of metal. DISCUSSION: We have shown that periprosthetic tissues of total elbow patients who have undergone revision for loosening and osteolysis contain polyethylene, cement, and metal debris. Although the polyethylene particles were of a size and shape that have been previously shown to result in activation of phagocytic cells, osteolysis after total elbow arthroplasty is a multimodal process. Because of the presence of multiple wear particle sources, a cause-and-effect relationship between polyethylene debris and osteolysis cannot be established with certainty.

Bone ingrowth in well-fixed retrieved porous tantalum implants.

While first generation porous coatings have had clinical success, aseptic loosening remains a leading cause of revision. The purpose of this study was to investigate the reasons for revision and to assess the amount of bone ingrowth in retrieved porous tantalum components. In a prospective multicenter retrieval program, 76 porous tantalum acetabular shells, 5 femoral stems, 7 patellas and 36 tibial trays were collected from revision surgeries. A subset of the implants was analyzed for bone ingrowth. The main reason for revision was infection for acetabular shells (1.4 years implantation time) and instability for tibial trays (1.8 years implantation time). Two of the thirty primary surgery acetabular shells and one of the thirty-six primary surgery tibial trays were revised for implant loosening. We observed full depth penetration of bone into the porous tantalum layer for the acetabular shells and femoral stems.

Does Taper Angle Clearance Influence Fretting and Corrosion Damage at the Head-Stem Interface? A Matched Cohort Retrieval Study.

Previous studies have speculated that modular taper design may have an effect on the corrosion and material loss at the taper surfaces. We present a novel method to measure taper angle for retrieved head taper and stem trunnions using a roundness machine (Talyrond 585, Taylor Hobson, UK). We also investigated the relationship between taper angle clearance and visual fretting-corrosion score at the taper-trunnion junction using a matched cohort study of 50 ceramic and 50 metal head-stem pairs. In this study, no correlation was observed between the taper angle clearance and the visual fretting-corrosion scores in either the ceramic or the metal cohorts.

Age-related skeletal dynamics and decrease in bone strength in DNA repair deficient male trichothiodystrophy mice.

Accumulation of DNA damage caused by oxidative stress is thought to be one of the main contributors of human tissue aging. Trichothiodystrophy (TTD) mice have a mutation in the Ercc2 DNA repair gene, resulting in accumulation of DNA damage and several features of segmental accelerated aging. We used male TTD mice to study the impact of DNA repair on bone metabolism with age. Analysis of bone parameters, measured by micro-computed tomography, displayed an earlier decrease in trabecular and cortical bone as well as a loss of periosteal apposition and a reduction in bone strength in TTD mice with age compared to wild type mice. Ex vivo analysis of bone marrow differentiation potential showed an accelerated reduction in the number of osteogenic and osteoprogenitor cells with unaltered differentiation capacity. Adipocyte differentiation was normal. Early in life, osteoclast number tended to be increased while at 78 weeks it was significantly lower in TTD mice. Our findings reveal the importance of genome stability and proper DNA repair for skeletal homeostasis with age and support the idea that accumulation of damage interferes with normal skeletal maintenance, causing reduction in the number of osteoblast precursors that are required for normal bone remodeling leading to a loss of bone structure and strength.

Do dynamic cement-on-cement knee spacers provide better function and activity during two-stage exchange?

BACKGROUND: Implantation of an antibiotic bone cement spacer is used to treat infection of a TKA. Dynamic spacers fashioned with cement-on-cement articulating surfaces potentially facilitate patient mobility and reduce bone loss as compared with their static counterparts, while consisting of a biomaterial not traditionally used for load-bearing articulations. However, their direct impact on patient mobility and wear damage while implanted remains poorly understood. QUESTIONS/PURPOSES: We characterized patient activity, surface damage, and porous structure of dynamic cement-on-cement spacers. METHODS: We collected 22 dynamic and 14 static knee antibiotic cement spacers at revision surgeries at times ranging from 0.5 to 13 months from implantation. For these patients, we obtained demographic data and UCLA activity levels. We characterized surface damage using the Hood damage scoring method and used micro-CT analysis to observe the internal structure, cracking, and porosity of the cement. RESULTS: The average UCLA score was higher for patients with dynamic spacers than for patients with static spacers, with no differences in BMI or age. Burnishing was the only prevalent damage mode on all the bearing surfaces. Micro-CT analysis revealed the internal structure of the spacers was porous and highly inhomogeneous, including heterogeneous dispersion of radiopaque material and cavity defects. The average porosity was 8% (range, 1%-29%) and more than ½ of the spacers had pores greater than 1 mm in diameter. CONCLUSIONS: Our observations suggest dynamic, cement-on-cement spacers allow for increased patient activity without catastrophic failure. Despite the antibiotic loading and internal structural inhomogeneity, burnishing was the only prevalent damage mode that could be consistently classified with no evidence of fracture or delamination. The porous structure of the spacers varied highly across the surfaces without influencing the material failure.

Lumbar total disc replacement impingement sensitivity to disc height distraction, spinal sagittal orientation, implant position, and implant lordosis.

STUDY DESIGN: A 3-dimensional finite element model of 2 lumbar motion segments (L4-L5 and L5-S1) was used to evaluate the sensitivity of lumbar total disc replacement (TDR) impingement to disc height distraction, spinal sagittal orientation, implant position, and implant lordosis. The models were implanted with a mobile-bearing TDR and exposed to simulated sagittally balanced erect posture. OBJECTIVE: The objective of this study was to determine the sensitivity of TDR impingement to disc height distraction, implant lordotic angle, implant anterior-posterior position, and spinal orientation relative to the horizon. SUMMARY OF BACKGROUND DATA: TDR has the potential to replace fusion as the "gold standard" for treatment of painful degenerative disc disease. However, complications after TDR have been associated with device impingement and accelerated polyethylene wear. METHODS: A previously developed finite element model of the lumbar spine was altered to include implantation of a mobile-bearing TDR. A series of sensitivity analyses was performed to determine impingement risk. Specifically, spinal orientation, disc height distraction, footplate lordotic angle, and anterior-posterior position were evaluated. RESULTS: Generally, TDR tended to result in an increase in extension rotation and facet contact force during simulated erect posture when compared with the intact models. Impingement risk was sensitive to all of the tested parameters. CONCLUSION: The data from this study indicate that lumbar mobile-bearing TDR impingement is sensitive to disc height distraction, anterior-posterior position, implant lordosis, and spinal sagittal orientation. TDR impingement risk can be minimized by choosing an implant with an appropriate amount of lordosis, not overdistracting the disc space, and taking care not to place the implant too far anterior or posterior.

Bone fragility and decline in stem cells in prematurely aging DNA repair deficient trichothiodystrophy mice.

Trichothiodystrophy (TTD) is a rare, autosomal recessive nucleotide excision repair (NER) disorder caused by mutations in components of the dual functional NER/basal transcription factor TFIIH. TTD mice, carrying a patient-based point mutation in the Xpd gene, strikingly resemble many features of the human syndrome and exhibit signs of premature aging. To examine to which extent TTD mice resemble the normal process of aging, we thoroughly investigated the bone phenotype. Here, we show that female TTD mice exhibit accelerated bone aging from 39 weeks onwards as well as lack of periosteal apposition leading to reduced bone strength. Before 39 weeks have passed, bones of wild-type and TTD mice are identical excluding a developmental defect. Albeit that bone formation is decreased, osteoblasts in TTD mice retain bone-forming capacity as in vivo PTH treatment leads to increased cortical thickness. In vitro bone marrow cell cultures showed that TTD osteoprogenitors retain the capacity to differentiate into osteoblasts. However, after 13 weeks of age TTD females show decreased bone nodule formation. No increase in bone resorption or the number of osteoclasts was detected. In conclusion, TTD mice show premature bone aging, which is preceded by a decrease in mesenchymal stem cells/osteoprogenitors and a change in systemic factors, identifying DNA damage and repair as key determinants for bone fragility by influencing osteogenesis and bone metabolism.

Polyethylene wear in retrieved reverse total shoulder components.

BACKGROUND: Reverse total shoulder arthroplasty has been used to treat rotator cuff tear arthropathy and proximal humerus fractures, as well as for failed conventional total shoulder prostheses. It has been suggested that polyethylene wear is potentially higher in reverse shoulder replacements than in conventional shoulder replacements. The modes and degree of polyethylene wear have not been completely elucidated. The purpose of this study was to evaluate polyethylene wear patterns in 7 specimens retrieved at revision arthroplasty and identify factors that may be associated with increased wear. METHODS: Reverse total shoulder components were retrieved from 7 patients during revision arthroplasty for loosening and/or pain. Preoperative glenoid tilt and placement and scapular notching were evaluated by use of preoperative radiographs. Polyethylene wear was evaluated via micro-computed tomography and optical microscopy. RESULTS: Wear on the rim of the polyethylene humeral cup was identified on all retrieved components. The extent of rim wear varied from a penetration depth of 0.1 to 4.7 mm. We could not show a correlation between scapular notching and rim wear. However, rim wear was more extensive when the inferior screw had made contact with the liner. Metal-on-metal wear between the humeral component and the inferior screw of 1 component was also observed. Wear of the intended bearing surface was minimal. DISCUSSION: Rim damage was the predominant cause of polyethylene wear in our retrieved specimens. Direct contact between the humeral component and inferior metaglene screws is concerning because this could lead to accelerated ultra-highmolecular weight polyethylene wear and also induce mechanical loosening of the glenoid component.

Prevalence and projections of total shoulder and elbow arthroplasty in the United States to 2015.

HYPOTHESIS: This study examined national trends and projections of procedure volumes and prevalence rates for shoulder and elbow arthroplasty in the United States (U.S.). This study hypothesized that the growth in demand for upper extremity arthroplasty will be greater than the growth in demand for hip and knee arthroplasty and that demand for these procedures will continue to grow in the immediate future. MATERIALS AND METHODS: The Nationwide Inpatient Sample (1993-2007) was used with U.S. Census data to quantify primary arthroplasty rates as a function of age, race, census region, and gender. Poisson regression was used to evaluate procedure rates and determine year-to-year trends in primary and revision arthroplasty. Projections were derived based on historical procedure rates combined with population projections from 2008 to 2015. RESULTS: Procedure volumes and rates increased at annual rates of 6% to 13% from 1993 to 2007. Compared with 2007 levels, projected procedures were predicted to further increase by between 192% and 322% by 2015. The revision burden increased from approximately 4.5% to 7%. During the period studied, the hospital length of stay decreased by approximately 2 days for total and hemishoulder procedures. Charges, in 2007 Consumer Price Index-adjusted dollars, increased for all 4 procedural types at annual rates of $900 to $1700. CONCLUSION: The growth rates of upper extremity arthroplasty were comparable to or higher than rates for total hip and knee procedures. Of particular concern was the increased revision burden. The rising number of arthroplasty procedures combined with increased charges has the potential to place a financial strain on the health care system.

Role of surgical position on interface stress and initial bone remodeling stimulus around hip resurfacing arthroplasty.

Valgus alignment of femoral resurfacing components has been advocated to reduce proximal femur loading and thus minimize the risk for femoral neck fractures. However, such reduction in loading may exacerbate undesirable stress shielding. This study examined the effect of extreme implant orientations (+/-15 degrees ) and stem canal overreaming on initial bone remodeling stimulus using finite element models. The changes in implant-cement interface stresses due to implant alignment were also evaluated. The valgus model showed increased initial bone resorption stimulus, which extended distally and peripherally around the femoral neck. The peak implant-cement interface shear stress for the varus model was 10.9 MPa, exceeding the interface shear strength. Overreaming of the stem canal eliminated distal tip loading, but proximal stress shielding was still unavoidable. These data show bone loading and interface fixation trends emanating from valgus and varus implant positions that will be of interest to practicing physicians.

Biomechanical comparison of 2 proximally coated femoral stems: effects of stem length and surface finish.

Proximally hydroxyapatite-coated stems have performed well clinically but produced moderate proximal stress shielding and midstem cancellous condensation. Stem modification (stem shortening and distal tip polishing) has resulted in greater incidence of thigh pain. We performed a retrospective finite element analysis of the effects of stem length and surface finish to determine if midstem fixation could be avoided and the results could relate to the clinical outcomes. The modified short stem not only produced moderately less proximal bone resorption but also exhibited greater instability with 40% to 94% greater bone-implant relative motion at the stem tip. Bone formation potential at the transition between the coated and uncoated regions of both stems was observed based on changes in strain energy density. These findings are consistent with previous radiographic and clinical comparisons of short- and long-stem designs. Increased pain incidence for short-stem patients may be related to decreased implant instability and increased interface relative motion.

Bone loss dynamics result in trabecular alignment in aging and ovariectomized rats.

Because of the destructive nature of techniques used to measure bone morphometry, studies of architectural changes and bone loss have utilized cross-sectional study designs, with all its inherent limitations in nuances. Here, the results of a longitudinal study using in vivo micro-CT are presented elucidating the dynamics of bone loss and architectural adaptation in rat models of aging and postmenopausal bone loss. Using 3-D methodology, we observed the changes in bone architecture in the proximal tibia of normally aging and ovariectomized rats for 54 weeks. Spatial patterns in bone resorption were observed that were similar for both groups. Remaining trabeculae increased in thickness or were remodeled into new trabecular structures, especially in the ovariectomized animals. The combination of bone loss and bone formation resulted in alignment of trabeculae across the growth plate. Cortical modeling that was associated with growth continued after cessation of longitudinal growth in the ovariectomized animals, resulting in shape changes of the proximal tibia. The organized nature of the changes in bone architecture that occurred after ovariectomy and the high similarity with the changes observed in the normally aging animals, suggest that estrogen depletion resulted in an acceleration of a normal bone adaptation process. The observed aligning of trabeculae suggests regulation through mechanical loading.

Ultrasonic characterization of human trabecular bone microstructure.

New quantitative ultrasound (QUS) techniques involving ultrasound backscattering have been introduced for the assessment of bone quality. QUS parameters are affected by the transducer characteristics, e.g. frequency range, wave and pulse length. Although frequency-dependent backscattering has been studied extensively, understanding of the ultrasound scattering phenomenon in trabecular bone is still limited. In the present study, the relationships between QUS parameters and the microstructure of human trabecular bone were investigated experimentally and by using numerical simulations. Speed of sound (SOS), normalized broadband ultrasound attenuation (nBUA), average attenuation, integrated reflection coefficient (IRC) and broadband ultrasound backscatter (BUB) were measured for 26 human trabecular bone cylinders. Subsequently, a high-resolution microCT system was used to determine the microstructural parameters. Moreover, based on the sample-specific microCT data, a numerical model for ultrasound propagation was developed for the simulation of experimental measurements. Experimentally, significant relationships between the QUS parameters and microstructural parameters were demonstrated. The relationships were dependent on the frequency, and the strongest association (r = 0.88) between SOS and structural parameters was observed at a centre frequency of 5 MHz. nBUA, average attenuation, IRC and BUB showed somewhat lower linear correlations with the structural properties at a centre frequency of 5 MHz, as compared to those determined at lower frequencies. Multiple regression analyses revealed that the variation of acoustic parameters could best be explained by parameters reflecting the amount of mineralized tissue. A principal component analysis demonstrated that the strongest determinants of BUB and IRC were related to the trabecular structure. However, other structural characteristics contributed significantly to the prediction of the acoustic parameters as well. The two-dimensional numerical model introduced in the present study demonstrated good agreement with the experimental measurements. However, further studies with the simulation model are warranted to systematically investigate the relation between the structural parameters and ultrasound scattering.

Prediction of density and mechanical properties of human trabecular bone in vitro by using ultrasound transmission and backscattering measurements at 0.2-6.7 MHz frequency range.

The ultrasound (US) backscattering method has been introduced as an alternative for the through-transmission measurement of sound attenuation and speed in diagnosis of osteoporosis. Both attenuation and backscattering depend strongly on the US frequency. In this study, 20 human trabecular bone samples were measured in transmission and pulse-echo geometry in vitro. The aim of the study was to find the most sensitive frequency range for the quantitative ultrasound (QUS) analyses. Normalized broadband US attenuation (nBUA), speed of sound (SOS), broadband US backscatter (BUB) and integrated reflection coefficient (IRC) were determined for each sample. The samples were spatially scanned with five pairs of US transducers covering a frequency range of 0.2-6.7 MHz. Furthermore, mechanical properties and density of the same samples were determined. At all frequencies, SOS, BUB and IRC showed statistically significant linear correlations with the mechanical properties or density of human trabecular bone (0.51 < r < 0.82, 0.54 < r < 0.81 and 0.70 < r < 0.85, respectively). In contrast to SOS, IRC and BUB, nBUA showed statistically significant correlations with mechanical parameters or density at the centre frequency of 1 MHz only. Our results suggest that frequencies up to 5 MHz can be useful in QUS analyses for the prediction of bone mechanical properties and density. Since the use of higher frequencies provides better axial and spatial resolution, improved structural analyses may be possible. While extensive attenuation of high frequencies in trabecular bone limits the clinically feasible frequency range, selection of optimal frequency range for in vivo QUS application should be carefully considered.

An improved segmentation method for in vivo microCT imaging.

UNLABELLED: Image segmentation methods for microCT can influence the accuracy of bone morphometry calculations. A new automated segmentation method is introduced, and its performance is compared with standard segmentation methods. The new method can improve the results of in vivo microCT, where the need to keep radiation dose low limits scan quality. INTRODUCTION: An important topic for microCT analysis of bone samples is the segmentation of the original reconstructed grayscale data sets to separate bone from non-bone. Problems like noise, resolution limitations, and beam-hardening make this a nontrivial issue. Inappropriate segmentation methods will reduce the potential power of microCT and may introduce bias in the architectural measurements, in particular, when new in vivo microCT with its inherent limitations in scan quality is used. Here we introduce a new segmentation method using local thresholds and compare its performance to standard global segmentation methods. MATERIAL AND METHODS: The local threshold method was validated by comparing the result of the segmentation with histology. Furthermore, the effect of choosing this new method versus standard segmentation methods using global threshold values was investigated by studying the sensitivity of these methods to signal to noise ratio and resolution. RESULTS: Using the new method on high-quality scans yielded accurate results and virtually no differences between histology and the segmented data sets could be observed. When prior knowledge about the volume fraction of the bone was available the global threshold also resulted in appropriate results. Degrading the scan quality had only minor effects on the performance of the new segmentation method. Although global segmentation methods were not sensitive to noise, it was not possible to segment both lower mineralized thin trabeculae and the higher mineralized cortex correctly with the same threshold value. CONCLUSION: At high resolutions, both the new local and conventional global segmentation methods gave near exact representations of the bone structure. When scanned samples are not homogenous (e.g., thick cortices and thin trabeculae) and when resolution is relatively low, the local segmentation method outperforms global methods. It maximizes the potential of in vivo microCT by giving good structural representation without the need to use longer scanning times that would increase absorption of harmful X-ray radiation by the living tissue.