Comparative Studies on the Organogel Formation of a Polyester in Three Different Base Oils by X-ray Analysis, Rheology and Infrared Spectroscopy.

High-performance greases typically consist of a base oil and polyurea as a thickener material. To date, few alternatives to polyureas have been investigated. Polyesters could be one such alternative; however, little is known about the gelation of such polyesters because, unlike polyureas, they cannot form hydrogen bonds between the polymer chains. Here, we present studies on the gel formation of a polyester based thickener poly(hexane dodecanoate) with 1-octanol endgroups in three different base oils, i.e., a mineral oil (Brightstock 150), a synthetic Polyalphaolefin (Spectrasyn 40) and castor oil (85 to 90 wt.% ricinoleic acid triglyceride). Small- and wide-angle X-ray scattering measurements indicate a strong interaction of the polyester with castor oil and an increase in the crystalline fraction, with an increasing polymer amount from 5 to 40 wt.%. Moreover, infrared analysis of the polyester in castor oil showed gel formation at a minimum concentration of 20 wt.%. The strong interaction of the polyester with castor oil compared to the other two base oils led to an increase in the yield point γF as a measure of the mechanical stability of the gel, which was determined to be 5.9% compared to 0.8% and 1.0% in Brightstock and Spectrasyn, respectively.

Polyurea Thickened Lubricating Grease-The Effect of Degree of Polymerization on Rheological and Tribological Properties.

Lubricating greases based on urea thickeners are frequently used in high-performance applications since their invention in 1954. One property that has so far been neglected in the further development of these systems due to their low solubility and the resulting difficulty of analysis, is to better understand how the degree of polymerization affect such polyurea lubricating systems. In this work, we prepared three different oligo- or polyurea systemswith different degrees of polymerization (DP) and investigated the influence of DP on rheological and tribological properties. The results showed that the DP has an influence on the flow limit in rheology as well as on the extreme pressure (EP) and anti-wear (AW) properties as examined by tribology measurements. By optimizing the DP for a thickener system, comparable EP and AW properties can be achieved through the use of additives. The DP showed an increasing influence on the flow limit. This could reduce damage to rolling bearings due to lateral loading at rest. Therefore, modifying the DP of the polyurea systems shows similar effects as the addition of external additives. Overall, this would reduce the use of additives in industrial applications.

Human Apolipoprotein A1 at Solid/Liquid and Liquid/Gas Interfaces.

An X-ray reflectivity study on the adsorption behavior of human apolipoprotein A1 (apoA1) at hydrophilic and hydrophobic interfaces is presented. It is shown that the protein interacts via electrostatic and hydrophobic interactions with the interfaces, resulting in the absorption of the protein. pH dependent measurements at the solid/liquid interface between silicon dioxide and aqueous protein solution show that in a small pH range between pH 4 and 6, adsorption is increased due to electrostatic attraction. Here, the native shape of the protein seems to be conserved. In contrast, the adsorption at the liquid/gas interface is mainly driven by hydrophobic effects, presumably by extending the hydrophobic regions of the amphipathic helices, and results in a conformational change of the protein during adsorption. However, the addition of differently charged membrane-forming lipids at the liquid/gas interface illustrates the ability of apoA1 to include lipids, resulting in a depletion of the lipids from the interface.

Production, deformation and mechanical investigation of magnetic alginate capsules.

In this article we investigated the deformation of alginate capsules in magnetic fields. The sensitivity to magnetic forces was realised by encapsulating an oil in water emulsion, where the oil droplets contained dispersed magnetic nanoparticles. We solved calcium ions in the aqueous emulsion phase, which act as crosslinking compounds for forming thin layers of alginate membranes. This encapsulating technique allows the production of flexible capsules with an emulsion as the capsule core. It is important to mention that the magnetic nanoparticles were stable and dispersed throughout the complete process, which is an important difference to most magnetic alginate-based materials. In a series of experiments, we used spinning drop techniques, capsule squeezing experiments and interfacial shear rheology in order to determine the surface Young moduli, the surface Poisson ratios and the surface shear moduli of the magnetically sensitive alginate capsules. In additional experiments, we analysed the capsule deformation in magnetic fields. In spinning drop and capsule squeezing experiments, water droplets were pressed out of the capsules at elevated values of the mechanical load. This phenomenon might be used for the mechanically triggered release of water-soluble ingredients. After drying the emulsion-filled capsules, we produced capsules, which only contained a homogeneous oil phase with stable suspended magnetic nanoparticles (organic ferrofluid). In the dried state, the thin alginate membranes of these particles were rather rigid. These dehydrated capsules could be stored at ambient conditions for several months without changing their properties. After exposure to water, the alginate membranes rehydrated and became flexible and deformable again. During this swelling process, water diffused back in the capsule. This long-term stability and rehydration offers a great spectrum of different applications as sensors, soft actuators, artificial muscles or drug delivery systems.

The Synergistic Effect of Cationic Moieties and GRGDSF-Peptides in Hydrogels on Neural Stem Cell Behavior.

This article reports the behavior of embryonic neural stem cells on a hydrogel that combines cationic, non-specific cell adhesion motifs with glycine-arginine-glycine-aspartic acid-serine-phenylalanine (GRGDSF)-peptides as specific cell adhesion moieties. Therefore, three hydrogels are prepared by free radical polymerization that contains either a GRGDSF-peptide residue (P1), amino ethylmethacrylate as a cationic residue (P2), or a combination of both motifs (P3). For each gel, cross linker concentrations of 8 mol% is used to have a comparable gel stiffness of 8-9 kPa. The cell experiments indicate a synergistic effect of the non-specific, cationic residues, and the specific GRGDSF-peptides on embryonic neural stem cell behavior that is especially pronounced in the cell adhesion experiments by more than doubling the number of cells after 72 h when comparing P3 with P2 and is less pronounced in the proliferation and differentiation experiments.

Solid-Supported Lipid Multilayers under High Hydrostatic Pressure.

In this work, the structure of solid-supported lipid multilayers exposed to increased hydrostatic pressure was studied in situ by X-ray reflectometry at the solid-liquid interface between silicon and an aqueous buffer solution. The layers' vertical structure was analyzed up to a maximum pressure of 4500 bar. The multilayers showed phase transitions from the fluid into different gel phases. With increasing pressure, a gradual filling of the sublayers between the hydrophilic head groups with water was observed. This process was inverted when the pressure was decreased, yielding finally smaller water layers than those in the initial state. As is commonly known, water has an abrasive effect on lipid multilayers by the formation of vesicles. We show that increasing pressure can reverse this process so that a controlled switching between multi- and bilayers is possible.

Structure of DPPC-hyaluronan interfacial layers - effects of molecular weight and ion composition.

Hyaluronan and phospholipids play an important role in lubrication in articular joints and provide in combination with glycoproteins exceptionally low friction coefficients. We have investigated the structural organization of 1,2-dipalmitoyl-sn-glycero-3-phosphocholine (DPPC) Langmuir layers at the solution-air interface at different length scales with respect to the adsorption of hyaluronan (HA). This allows us to assemble a comprehensive picture of the adsorption and the resulting structures, and how they are affected by the molecular weight of HA and the presence of calcium ions. Brewster angle microscopy and grazing incident diffraction were used to determine the lateral structure at the micro- and macro scale. The data reveals an influence of HA on both the macro and micro structure of the DPPC Langmuir layer, and that the strength of this effect increases with decreasing molecular weight of HA and in presence of calcium ions. Furthermore, from X-ray reflectivity measurements we conclude that HA adsorbs to the hydrophilic part of DPPC, but data also suggest that two types of interfacial structures are formed at the interface. We argue that hydrophobic forces and electrostatic interactions play important rules for the association between DPPC and HA. Surface pressure area isotherms were used to determine the influence of HA on the phase behavior of DPPC while electrophoretic mobility measurements were used to gain insight into the binding of calcium ions to DPPC vesicles and hyaluronan.

Mixed Layers of Nonionic Dendritic Amphiphiles and DPPC at the Water Surface.

Nonionic dendritic amphiphiles that self-assemble into defined supramolecular aggregates are useful for the efficient solubilization of active agents, for example, in drug delivery. We investigated a new class of dendritic amphiphiles based on a hydrophilic polyol dendron head connected to a two-chain hydrophobic block. In analogy to phospholipids, these molecules form well-organized layers in bulk (vesicles) or at the water surface (Langmuir monolayer). The actual study focuses on the phase behavior and microscopic structure of mixed Langmuir layers of theses dendritic amphiphiles with the well-known phospholipid DPPC. The combination of surface pressure area isotherms with X-ray grazing incident diffraction and Brewster angle microscopy gives us information on the phase behavior of the mixed monolayers and the orientation of the amphiphiles inside the condensed domains with molecular resolution. We could prove that the dendritic generation and, by this, the headgroup size of the amphiphilic molecules have a significant influence on their interaction with DPPC at the air-water interface. Thus, our findings are important for the understanding of mixed lipid membranes in general as well as for the preparation of artificial membranes and vesicles with adjustable properties, e.g., their drug delivery potential.

Salt induced reduction of lysozyme adsorption at charged interfaces.

A study of lysozyme adsorption below a behenic acid membrane and at the solid-liquid interface between aqueous lysozyme solution and a silicon wafer in the presence of sodium chloride is presented. The salt concentration was varied between 1 mmol L(-1) and 1000 mmol L(-1). X-ray reflectivity data show a clear dependence of the protein adsorption on the salt concentration. Increasing salt concentrations result in a decreased protein adsorption at the interface until a complete suppression at high concentrations is reached. This effect can be attributed to a reduced attractive electrostatic interaction between the positively charged proteins and negatively charged surfaces by charge screening. The measurements at the solid-liquid interfaces show a transition from unoriented order of lysozyme in the adsorbed film to an oriented order with the short protein axis perpendicular to the solid-liquid interface with rising salt concentration.

Magneto-responsive alginate capsules.

Upon incorporation of magnetic nanoparticles (mNPs) into gels, composite materials called ferrogels are obtained. These magneto-responsive systems have a wide range of potential applications including switches and sensors as well as drug delivery systems. In this article, we focus on the properties of calcium alginate capsules, which are widely used as carrier systems in medicine and technology. We studied the incorporation of different kinds of mNPs in matrix capsules and in the core and the shell of hollow particles. We found out that not all particle-alginate or particle-CaCl2 solution combinations were suitable for a successful capsule preparation on grounds of a destabilization of the nanoparticles or the polymer. For those systems allowing the preparation of switchable beads or capsules, we systematically studied the size and microscopic structure of the capsules, their magnetic behavior and mechanical resistance.

About the role of surfactants on the magnetic control over liquid interfaces.

The behavior of magnetically responsive aqueous Fe(III) surfactant solutions at liquid interfaces is analyzed. Such surfactants attracted much attention, because of the ability to manipulate interfaces by magnetic fields without any use of magnetic nanoparticles. A detailed analysis of the surface properties proves that the mixing of paramagnetic electrolyte solution with anionic, cationic and nonionic surfactants yields the similar magnetic response and no effect of the surfactant charge can be observed. We conclude that the observed magnetic shiftability of interfaces is caused by a combination of the paramagnetic behavior of the bulk liquid and a reduction of the surface tension. Thus, this work gives an alternative interpretation of the properties of "magnetic surfactants" compared to the ones claimed in the literature.

Prebiotic cell membranes that survive extreme environmental pressure conditions.

Attractive candidates for compartmentalizing prebiotic cells are membranes comprised of single-chain fatty acids. It is generally believed that life may have originated in the depth of the protoocean, that is, under high hydrostatic pressure conditions, but the structure and physical-chemical properties of prebiotic membranes under such conditions have not yet been explored. We report the temperature- and pressure-dependent properties of membranes composed of prebiotically highly-plausible lipids and demonstrate that prebiotic membranes could not only withstand extreme temperatures, but also serve as robust models of protocells operating in extreme pressure environments. We show that pressure not only increases the stability of vesicular systems but also limits their flexibility and permeability to solutes, while still keeping the membrane in an overall fluid-like and thus functional state.

Exploring the synthesis of a new group of chiral ammonium salts with specific configurations at the stereogenic nitrogen centers.

A group of new chiral dications with a fixed, specific configuration at the stereogenic nitrogen center was created. Stereoselective synthesis and recrystallization give the diastereomerically and enantiomerically pure dications, including a chiral amphiphile with surface-active properties.

Elastometry of deflated capsules: elastic moduli from shape and wrinkle analysis.

Elastic capsules, prepared from droplets or bubbles attached to a capillary (as in a pendant drop tensiometer), can be deflated by suction through the capillary. We study this deflation and show that a combined analysis of the shape and wrinkling characteristics enables us to determine the elastic properties in situ. Shape contours are analyzed and fitted using shape equations derived from nonlinear membrane-shell theory to give the elastic modulus, Poisson ratio and stress distribution of the membrane. We include wrinkles, which generically form upon deflation, within the shape analysis. Measuring the wavelength of wrinkles and using the calculated stress distribution gives the bending stiffness of the membrane. We compare this method with previous approaches using the Laplace-Young equation and illustrate the method on two very different capsule materials: polymerized octadecyltrichlorosilane (OTS) capsules and hydrophobin (HFBII) coated bubbles. Our results are in agreement with the available rheological data. For hydrophobin coated bubbles, the method reveals an interesting nonlinear behavior consistent with the hydrophobin molecules having a rigid core surrounded by a softer shell.

Formation of iron containing aggregates at the liquid-air interface.

The early stages of the formation of inorganic aggregates, composed of iron compounds at the solution-air interface, were investigated in situ. The properties of the solution-air interface were changed by using different Langmuir layers. In order to get insight into the evolution of the sample system in situ, the processes were studied by X-ray scattering and spectroscopy techniques. The formation of aggregates was detected under cationic as well as under anionic Langmuir layers. The observed compounds lack long range order which indicates the formation of amorphous structures. This is supported by extended X-ray absorption fine structure measurements showing only minor order in the formed aggregates.

Film formation of nonionic dendritic amphiphiles at the water surface.

This study focuses on the modular synthesis of a new class of nonionic dendritic amphiphiles and their behavior at the water-air interface. Our approach is based on a modular architecture consisting of two different generations of hydrophilic polyol dendrons connected to a two-chain hydrophobic block. Caused by different polarities of polyol and aliphatic groups, the molecules are surface-active and, by analogy to phospholipids, can form well-organized Langmuir monolayers at the water surface. The self-association process and phase behavior of these molecules with two different headgroup sizes were investigated by means of surface pressure and surface potential area isotherms by surface shear rheology and Brewster angle microscopy. With these techniques, we were able to observe marked differences in the phase behavior of the two molecular generations.

Adsorption of nanoparticles at the solid-liquid interface.

The adsorption of differently charged nanoparticles at liquid-solid interfaces was investigated by in situ X-ray reflectivity measurements. The layer formation of positively charged maghemite (γ-Fe(2)O(3)) nanoparticles at the aqueous solution-SiO(2) interface was observed while negatively charged gold nanoparticles show no adsorption at this interface. Thus, the electrostatic interaction between the particles and the charged surface was determined as the driving force for the adsorption process. The data analysis shows that a logarithmic particle size distribution describes the density profile of the thin adsorbed maghemite layer. The size distribution in the nanoparticle solution determined by small angle X-ray scattering shows an average particle size which is similar to that found for the adsorbed film. The formed magehemite film exhibits a rather high stability.

Dissolution of iron oxide nanoparticles inside polymer nanocapsules.

The structure of poly(organosiloxane) nanocapsules partially filled with iron oxide cores of different sizes was revealed by small angle X-ray scattering and X-ray diffraction. The nanocapsules are synthesized by the formation of a poly(organosiloxane) shell around iron oxide nanoparticles and the simultaneous partial dissolution of these cores. Due to the high scattering contrast of the iron oxide cores compared to the polymer shell, the particle size distribution of the cores inside the capsules can be measured by small angle X-ray scattering. Additional information can be revealed by X-ray diffraction, which gives insights into the formation of the polymer network and the structure of the iron oxide cores. The study shows how the crystallinity and size of the nanoparticles as well as the shape and width of the size distribution can be altered by the synthesis parameters.

Mechanical properties of liquid-filled shellac composite capsules.

This paper describes the mechanical properties of thin-walled, liquid-filled composite capsules consisting of calcium pectinate and shellac. In a series of experiments we measured the deformation of these particles in a spinning drop apparatus. For different pH-values we studied the elastic properties of these particles and compared the obtained results with the mechanical response measured by squeezing capsule experiments. In analogy to these experiments, we also investigated liquid-filled unloaded calcium pectinate capsules without the addition of shellac. The deformation properties of these experiments and the surface Young moduli were in good agreement. Furthermore we investigated the liquid-filled calcium pectinate and the composite capsules by NMR microscopy. These experiments allowed investigations of the membrane thickness and the kinetics of membrane growing. Additional characterizations by stress controlled small amplitude surface shear experiments of similar composed gel layers provided coherent results for the surface Young modulus.

Sticking polydisperse hydrophobic magnetite nanoparticles to lipid membranes.

The formation of a layer of hydrophobic magnetite (Fe(3)O(4)) nanoparticles stabilized by lauric acid is analyzed by in situ X-ray reflectivity measurements. The data analysis shows that the nanoparticles partially disperse their hydrophobic coating. Consequently, a Langmuir layer was formed by lauric acid molecules that can be compressed into an untilted condensed phase. A majority of the nanoparticles are attached to the Langmuir film integrating lauric acid residue on their surface into the Langmuir film. Hence, the particles at the liquid-gas interface can be identified as so-called Janus beads, which are amphiphilic solids having two sides with different functionality.