Effect of Synthesis Method on Reaction Mechanism for Hydrogen Evolution over CuxOy/TiO2 Photocatalysts: A Kinetic Analysis.

The existing literature survey reports rare and conflicting studies on the effect of the preparation method of metal-based semiconductor photocatalysts on structural/morphological features, electronic properties, and kinetics regulating the photocatalytic H2 generation reaction. In this investigation, we compare the different copper/titania-based photocatalysts for H2 generation synthesized via distinct methods (i.e., photodeposition and impregnation). Our study aims to establish a stringent correlation between physicochemical/electronic properties and photocatalytic performances for H2 generation based on material characterization and kinetic modeling of the experimental outcomes. Estimating unknown kinetic parameters, such as charge recombination rate and quantum yield, suggests a mechanism regulating charge carrier lifetime depending on copper distribution on the TiO2 surface. We demonstrate that H2 generation photoefficiency recorded over impregnated CuxOy/TiO2 is related to an even distribution of Cu(0)/Cu(I) on TiO2, and the formation of an Ohmic junction concertedly extended charge carrier lifetime and separation. The outcomes of the kinetic analysis and the related modeling investigation underpin photocatalyst physicochemical and electronic properties. Overall, the present study lays the groundwork for the future design of metal-based semiconductor photocatalysts with high photoefficiencies for H2 evolution.

A novel green approach for silver recovery from chloride leaching solutions through photodeposition on zinc oxide.

Silver is extensively used in electronics, industrial catalysis, and biomedical sector owing to its enhanced physicochemical properties. E-waste recycling may contribute significantly to enhance silver recovery in the view of a circular economy and limit the depletion of mineral sources. In this scenario, hydrometallurgical routes represent the most widely used techniques for silver extraction/recovery and require strong acidic solutions, high temperatures, and multiple operating units. An alternative sustainable route for silver recovery from leaching solutions used for silver extraction in industrial applications is herein proposed for the first time. The novel green process of silver recovery is based on the UV/vis light-driven photocatalytic deposition of pure metallic silver over low-cost and non-toxic ZnO photocatalyst. In the second step, ZnO is dissolved by slight acidification and pure metallic silver is easily recovered. Low environmental impact, mild operating conditions, and economic viability are among the major perks of the new silver recovery process developed. In the view of a full-scale implementation, several operating conditions of the recovery process (i.e., photocatalyst load, starting silver concentration, type of hole scavenger and irradiation) were thoroughly investigated. A mathematical model capable of describing the system behaviour under different operating conditions was also developed and allowed to estimate unknown kinetic parameters for the Ag-photodeposition process.

Zero-valent palladium dissolution using NaCl/CuCl2 solutions.

Pd, Rh, Pt are employed in a wide range of applications, such as catalytic converters, fuel cells and electronic devices. In the last years, an increasing pressure on their market was recorded due to a growing demand and limited resources. Therefore, the recovery of these materials from wastes represents an interesting goal to be achieved. The most widely proposed techniques for recovering the palladium from wastes are leaching and ion exchange. Strong oxidizers, acids and high temperature (343-363 K) are used for leaching, leading problems for the environment and the safety. In this work the attention was focused on a system containing zero-valent palladium nanoparticles in which the leaching is performed in mild acidic conditions, by using chloride solutions containing cupric ions (NaCl/CuCl2). The process was studied at varying temperature, pH, chloride and cupric ion concentrations. Good results were obtained at pH 5.0 and temperatures between 288 K and 333 K. The process is more acceptable than the traditional ones from a safety point of view being characterized by less severe conditions (pH and temperatures). A shrinking spherical particles model was adopted to analyse the experimental data from which a development under a kinetic control was demonstrated.

Sacrificial photocatalysis: removal of nitrate and hydrogen production by nano-copper-loaded P25 titania. A kinetic and ecotoxicological assessment.

The photocatalytic removal of nitrate with simultaneous hydrogen generation was demonstrated using zero-valent nano-copper-modified titania (P25) as photocatalyst in the presence of UV-A-Vis radiation. Glycerol, a by-product in biodiesel production, was chosen as a hole scavenger. Under the adopted experimental conditions, a nitrate removal efficiency up to 100% and a simultaneous hydrogen production up to 14 µmol/L of H2 were achieved (catalyst load = 150 mg/L, initial concentration of nitrate = 50 mg/L, initial concentration of glycerol = 0.8 mol/L). The reaction rates were independent of the starting glycerol concentration. This process allows accomplishing nitrate removal, with the additional benefit of producing hydrogen under artificial UV-A radiation. A kinetic model was also developed and it may represent a benchmark for a detailed understanding of the process kinetics. A set of acute and chronic bioassays (Vibrio fischeri, Raphidocelis subcapitata, and Daphnia magna) was performed to evaluate the potential ecotoxicity of the nitrate/by-product mixture formed during the photocatalytic process. The ecotoxicological assessment indicated an ecotoxic effect of oxidation intermediates and by-products produced during the process.

Fe(III)-photocatalytic partial oxidation of benzyl alcohol to benzaldehyde under UV-solar simulated radiation.

A great deal of interest is recorded among researchers in the identification of new catalytic systems that make possible the selective oxidation of organic species in the presence of non-toxic solvents, primarily water, through the use of inexpensive catalysts. The possibility to selectively oxidize benzyl alcohol to benzaldehyde is studied in the present work by using ferric ions as homogeneous catalysts and oxygen as an oxidant under UV-solar simulated radiation. Due to the possibility that Fe(III) aquo-complex photolysis could generate undesired reactive OH radicals with the consequent occurrence of side reactions, most of the runs are carried out at pH = 0.5 at which these events have a reduced incidence. The results indicate that benzyl alcohol can be partially converted into benzaldehyde with yield and selectivity values higher than 40% and 80% respectively for the conditions adopted, with a minor occurrence of benzoic acid formation. Reaction schemes to account for the experimental observations are provided.

Photodegradation of naproxen and its photoproducts in aqueous solution at 254 nm: a kinetic investigation.

The kinetics of photodegradation of the non steroidal anti-inflammatory drug naproxen (+)-S-2-(6-methoxynaphthalen-2-yl)propanoic acid, an emerging organic pollutant, was studied in aqueous solutions under deaerated and aerated conditions. The photolysis experiments were carried out under monochromatic irradiation (λ = 254 nm) at pH = 7.0 and T = 25 °C. Simplified reaction schemes of photodegradation of naproxen are proposed in absence and in presence of oxygen respectively. The schemes take into account the photolysis of naproxen and its photoproducts and the reactions of the measured species with oxygen dissolved in the liquid bulk. According to these schemes, two kinetic models were developed which correlate the experimental data, for runs performed in absence and in presence of oxygen, with a fair accuracy and allowed to estimate the best values for the unknown kinetic parameters. The calculated quantum yield of direct photolysis of naproxen under deaerated media is in good agreement with the one previously reported. Under aerated conditions, the generation of singlet oxygen has also been taken into account. The obtained results, under the adopted conditions, indicated a marked influence of dissolved oxygen on the photodegradation rates of naproxen and the relative distribution of the major reaction intermediates.

Kinetic and chemical characterization of thermal decomposition of dicumylperoxide in cumene.

Dicumylperoxide (DCP) is one of the most used peroxides in the polymer industry. It has been reported that its thermal decomposition can result in runaway phenomena and thermal explosions with significant economic losses and injuries to people. In the present paper thermal behaviour of dicumylperoxide in cumene was investigated over the temperature range of 393-433 K under aerated and de-aerated conditions. The results indicated that when oxygen was present, the decomposition rate did not follow a simple pseudo-first order kinetic as previously reported in literature. A satisfactory fit of the experimental data was, in this case, achieved by means of kinetic expression derived under the assumption of an autocatalytic scheme of reaction. The reaction rate was, on the contrary, correctly described by a pseudo-first order kinetic in absence of oxygen. Under both aerated and de-aerated conditions, chemical analysis showed that the decomposition mainly resulted in the formation of acetophenone and dimethylphenylcarbinol with minor occurrence of 2,3-dimethyl-2,3-diphenylbutane. The formation of methane and ethane was also invariably observed while the appearance of cumylhydroperoxide as a reaction intermediate was detected under only aerated conditions. Therefore, two reaction schemes were proposed to explain system behaviour in the presence of oxygen and after its purging.

Oxidation of 2,4-dichlorophenol and 3,4-dichlorophenol by means of Fe(III)-homogeneous photocatalysis and algal toxicity assessment of the treated solutions.

Chlorophenols are used worldwide as broad-spectrum biocides and fungicides. They have half-life times in water from 0.6 to 550 h and in sediments up to 1700 h and, due to their numerous origins, they can be found in wastewaters, groundwaters or soils. Moreover, chlorophenols are not readily biodegradable. Recently, classic Advanced Oxidation Processes (AOP) have been proposed for their abatement in an aqueous solution. This paper investigates the oxidation of 2,4-dichlorophenol and 3,4-dichlorophenol, at starting concentrations of 6.1 · 10(-5) mol L(-1), in aqueous solutions through Fe(III)/O(2) homogeneous photocatalysis under UV light (303 ÷ 366 nm). The Fe(III)/O(2) homogeneous photocatalysis is less expensive than using H(2)O(2) due to the capability of Fe(III) to produce OH radicals, if irradiated with an UVA radiation, and of oxygen to re-oxidize ferrous ions to ferric ones when dissolved in solution. The results show that the best working conditions, for both compounds, are found for pH=3.0 and initial Fe(III) concentration equal to 1.5 · 10(-4) mol L(-1) although the investigated oxidizing system can be used even at pH close to 4.0 but with slower abatement kinetics. Toxicity assessment on algae indicates that treated solutions of 2,4-dichlorophenol are less toxic on algae Pseudokirchneriella subcapitata if compared to not treated solutions whereas in the case of 3,4-dichlorophenol only the samples collected during the runs at 20 and 60 min are capable of inhibiting the growth of the adopted organism. The values of the kinetic constant for the photochemical re-oxidation of iron (II) to iron (III) and for HO attack to intermediates are evaluated by a mathematical model for pH range of 2.0-3.0 and initial Fe(III) concentrations range of 1.5 · 10(-5)-5.2 · 10(-4) mol L(-1).

A procedure for the assessment of the toxicity of intermediates and products formed during the accidental thermal decomposition of a chemical species.

The knowledge of the substances which form when a molecule undergoes chemical reactions under unusual conditions is required by European legislation to evaluate the risks associated with an industrial chemical process. A thermal decomposition is often the result of a loss of control of the process which leads to the formation of many substances in some cases not easily predictable. The evaluation of the change of an overall toxicity passing from the parent compound to the mixture of its thermal decomposition products has been already proposed as a practical approach to this problem when preliminary indications about the temperature range in which the molecule decomposes are available. A new procedure is proposed in this work for the obtainment of the mixtures of thermal decomposition products also when there is no previous information about the thermal behaviour of investigated molecules. A scanning calorimetric run that is aimed to identify the onset temperature of the decomposition process is coupled to an isoperibolic one in order to obtain and collect the products. An algal strain is adopted for toxicological assessments of chemical compounds and mixtures. An extension of toxicological investigations to human cells is also attempted.

Kinetic investigation of Cu(II) ions photoreduction in presence of titanium dioxide and formic acid.

The photoreduction of Cu(II) in presence of an organic species as sacrificial agent has been investigated by many research groups but some controversial results are reported in literature. In this work, the photoreduction process of Cu(II) in presence of formic acid is investigated aiming at clarifying the reaction mechanism and assess the reaction kinetics. The effect of operating conditions such as TiO(2) load, initial concentration of sacrificial agent, pH and ionic strength was studied. The results of the work are: (1) the system reactivity does not depend neither on pH (in the range 2.0-3.5) nor on ionic strength of the solution; (2) formic acid is adsorbed on TiO(2) surface; (3) the nature of anionic species can influence the Cu(II) photoreduction (e.g. the addition of sulphate or phosphates reduces the reaction rates); and (4) FA can be completely mineralized during this photoxidation process; for example, this is observed for a TiO(2) load of 0.1g/L after a reaction time of about 240 min. A simplified kinetic model is developed to describe the behavior of the system and validated by analysing the data collected during the experimental work.

Effect of combined physico-chemical processes on the phytotoxicity of olive mill wastewaters.

A pool of laboratory experiments is planned with the aim of evaluating the possibility to reduce the phytotoxicity of olive mill wastewater (OMW) with combined physico-chemical processes (centrifugation-ozonation, centrifugation-solar photolysis, centrifugation-solar modified photoFenton, centrifugation-solar modified photoFenton-ozonation). A moderate COD removal of an OMW is reached by using ozonation or solar modified photoFenton separately or solar modified photoFenton/O(3) combined process even for prolonged treatment times. The O(3)-treated OMWs are still toxic towards algal growth (Pseudokirchneriella subcapitata) and only for dilutions equal to or higher than 1:160 a stimulation of algal growth is observed. The sole ozonation does not reduce significantly the phytotoxicity of tested OMW measured through the GI calculation of Raphanus sativus L., Cucumis sativus L. and Lactuca sativa L. A marked reduction of OMW inhibition, higher than 50%, is evidenced for 1:8 dilution OMW samples ozonated for 2h. The long-term storage of OMW associated with solar irradiation without or with Fe(III) ions under continuous aeration is less efficient than ozonation, and the combined action of the two former treatments does not significantly contribute to enhance both COD removal and germination index. Better results are obtained on seed germination and root elongation of plantlets of the three selected species, which germinated on OMW-free solidified medium and were then transferred on a solidified culture medium containing O(3)-treated OMW diluted 1:2 and 1:4. The operating costs are estimated for the solar modified photoFenton-ozonation process.

Use of an amorphous iron oxide hydrated as catalyst for hydrogen peroxide oxidation of ferulic acid in water.

The abatement of ferulic acid (FA), a polyphenolic constituent of olive mill wastewater, is studied in the pH range 5.0-7.0 by using hydrogen peroxide and an amorphous iron oxide as catalyst. The effect of pH, catalyst load, hydrogen peroxide and substrate starting concentrations is assessed during the investigation. A suitable reaction scheme is developed and used to build a mathematical model which satisfactorily describes the system's behavior. Kinetic constants for the proposed scheme as well as the total active site concentration of the catalyst in the studied pH range are estimated. The occurrence of internal mass-transfer limitation for the adopted granulometric fraction of the catalyst is demonstrated.