Microstructural and Corrosion Properties of Hydroxyapatite Containing PEO Coating Produced on AZ31 Mg Alloy.

In this work, the composition of an electrolyte was selected and optimized to induce the formation of hydroxyapatite during Plasma electrolytic oxidation (PEO) treatment on an AZ31 alloy for application in bioabsorbable implants. In detail, the PEO process, called PEO-BIO (Plasma Electrolytic Oxidation-Biocompatible), was performed using a silicate-phosphate-based electrolyte with the addition of calcium oxide in direct-current mode using high current densities and short treatment times. For comparison, a known PEO process for producing anticorrosive coatings, called standard, was applied on the same alloy. The coatings were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and XPS analyses. The corrosion performance was evaluated in simulated body fluid (SBF) at 37 °C. The coating produced on the PEO-BIO sample was porous and thicker than the standard PEO one, with zones enriched in Ca and P. The XRD analysis showed the formation of hydroxyapatite and calcium oxides in addition to magnesium-silicon oxide and magnesium oxide in the PEO-BIO sample. The corrosion resistance of PEO-BIO sample was comparable with that of a traditional PEO treated sample, and higher than that of the untreated alloy.

Low-Temperature Solution Crystallization of Nanostructured Oxides and Thin Films.

As an introduction to this themed issue, a critically selected overview of recent progress on the topic of solution methods for the low-temperature crystallization of nanoscale oxide materials is presented. It is focused on the low-temperature solution processing of oxide nanostructures and thin films. Benefits derived from these methods span from minimizing the environmental impact to reducing the fabrication costs. In addition, this topic is regarded as a key objective in the area because it offers a unique opportunity for the use of these materials in areas like flexible electronics, energy conversion and storage, environmental sciences, catalysis, or biomedicine.

Exploring the Phase-Selective, Green, Hydrothermal Synthesis of Upconverting Doped Sodium Yttrium Fluoride: Effects of Temperature, Time, and Precursors.

The aim of this work was i) to develop a hydrothermal, low-temperature synthesis protocol affording the upconverting hexagonal phase NaYF4 with suitable dopants while adhering to the "green chemistry" standards and ii) to explore the effect that different parameters have on the products. In optimizing the synthesis protocol, short reaction times and low temperatures (below 150 °C) were considered. Yb3+ and Er3+ ions were chosen as dopants for the NaYF4 material. Within the context of the second goal, parameters including nature of the precursors, treatment temperature, and treatment time were investigated to afford a pure hexagonal crystalline phase, both in the doped and undoped materials. To fully explore the synthesis results, the prepared materials were characterized from a structural (XRD), compositional (XPS, ICP-MS), and morphological (SEM) point of view. The upconverting properties of the compounds were confirmed by photoluminescence measurements.

Simple, common but functional: biocompatible and luminescent rare-earth doped magnesium and calcium hydroxides from miniemulsion.

Nanostructured (d∼ 20-35 nm) and highly luminescent Ca(OH)2:Ln and Mg(OH)2:Ln (Ln = EuIII, SmIII, TbIII, Mg(Ca)/Ln = 20 : 1 atomic) nanostructures were obtained in inverse (water in oil - w/o) miniemulsion (ME), by exploiting the nanosized compartments of the droplets to spatially confine the hydroxide precipitation in basic environment (NaOH). The functional nanostructures were prepared using different surfactants (Span80 (span) and a mixture of Igepal co-630 and Brij 52 (mix)) to optimise ME stability and hydroxide biocompatibility as well as tune the droplet sizes. X-Ray diffraction (XRD) analyses testify the achievement of a pure brucite-Mg(OH)2-phase and pure portlandite-Ca(OH)2-phase with a high degree of crystallinity. Besides structural characterisations, the products were thoroughly characterised by means of several and complementary techniques (dynamic light scattering (DLS), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), thermogravimetric analysis (TGA) and differential scanning calorimetry (DSC), micro-Raman spectroscopy, inductively coupled plasma mass spectrometry (ICP-MS) and Fourier transform infrared spectroscopy (FT-IR)) to assess their chemico-physical properties as well as their morphological and microstructural features. The stoichiometry of the doped systems was confirmed using ICP-MS measurements. Finally, the cytotoxicity of the nanoparticles was assessed by in vitro tests using ES2 cells in order to provide preliminary data on the biocompatibility of this kind of nanoparticles. The luminescence of the Eu-doped and Tb-doped materials is clearly visible to the naked eye in the red and green regions, respectively, corroborating their employment as materials for imaging in the optical window of interest.