RESUMEN
To determine whether the mechanical properties of joint soft tissues such as cartilage can be calculated from quantitative magnetic resonance imaging (MRI) data, we investigated whether the mechanical properties of articular cartilage and meniscus scheduled to be resected during arthroplasty are correlated with the T2 relaxation time on quantitative MRI at the same location. Six patients who had undergone knee arthroplasty and seven who had undergone hip arthroplasty were examined. For the knee joint, the articular cartilage and lateral meniscus of the distal lateral condyle of the femur and proximal lateral tibia were examined, while for the hip joint, the articular cartilage above the femoral head was studied. We investigated the relationship between T2 relaxation time by quantitative MRI and stiffness using a hand-made compression tester at 235 locations. The patient-individualized template technique was used to align the two measurement sites. The results showed a negative correlation (from -0.30 to -0.35) in the less severely damaged articular cartilage and meniscus. This indicates that tissue mechanical properties can be calculated from T2 relaxation time, suggesting that quantitative MRI is useful in determining when to start loading after interventional surgery on cartilage tissue and in managing the health of elderly patients.
RESUMEN
Nanofibrous scaffolds fabricated via electrospinning have been proposed for meniscus tissue regeneration. However, the electrospinning process is slow, and can only generate scaffolds of limited thickness with densely packed fibers, which limits cell distribution within the scaffold. In this study, we explored whether pneumatospinning could produce thicker collagen type I fibrous scaffolds with higher porosity, that can support cell infiltration and neo-fibrocartilage tissue formation for meniscus tissue engineering. We pneumatospun scaffolds with solutions of collagen type I with thicknesses of approximately 1 mm in 2 h. Scanning electron microscopy revealed a mix of fiber sizes with diameters ranging from 1 to 30 µm. The collagen scaffold porosity was approximately 48% with pores ranging from 7.4 to 100.7 µm. The elastic modulus of glutaraldehyde crosslinked collagen scaffolds was approximately 45 MPa, when dry, which reduced after hydration to 0.1 MPa. Mesenchymal stem cells obtained from the infrapatellar fat pad were seeded in the scaffold with high viability (>70%). Scaffolds seeded with adipose-derived stem cells and cultured for 3 weeks exhibited a fibrocartilage meniscus-like phenotype (expressing COL1A1, COL2A1 and COMP). Ex vivo implantation in healthy bovine and arthritic human meniscal explants resulted in the development of fibrocartilage-like neotissues that integrated with the host tissue with deposition of glycosaminoglycans and collagens type I and II. Our proof-of-concept study indicates that pneumatospinning is a promising approach to produce thicker biomimetic scaffolds more efficiently that electrospinning, and with a porosity that supports cell growth and neo-tissue formation using a clinically relevant cell source.
RESUMEN
Conventional magnetic resonance imaging (MRI) often acquires no signal in anterior cruciate ligament (ACL) due to the short apparent transverse relaxation time of ACL. Ultrashort echo time (UTE) MRI is capable of imaging ACL with high signal which enables quantitative ACL assessment. This study aimed to investigate the correlations of the mechanical and microstructural properties of human ACL specimens with quantitative three-dimensional UTE Cones (3D-UTE-Cones) MRI measures. ACL specimens were harvested from cadaveric knee joints of 13 (50.9 ± 21.1 years old, 11 males and 2 female) donors. Specimens were scanned using a series of quantitative 3D-UTE-Cones T2 * (UTE-T2 *), T1 (UTE-T1 ), Adiabatic T1ρ (UTE-Adiab-T1ρ ), and magnetization transfer (UTE-MT) sequences in a wrist coil on a clinical 3T scanner. ACL elastic modulus was measured using a uniaxial tensile mechanical test. Histomorphometry analysis was performed to measure the average fascicle specific surface, fascicle size, and number of cells per unit area. Spearman's rank correlations of UTE-MRI biomarkers with mechanical and histomorphometry measures were investigated. The elastic modulus of ACL showed significant moderate correlations with UTE-Adiab-T1ρ (R = -0.59, p = 0.01), macromolecular fraction from MT modeling (R = 0.54, p = 0.01), magnetization transfer ratio (R = 0.53, p = 0.01), UTE-T2* (R = -0.53, p = 0.01), and average fascicle specific surface (R = 0.54, p = 0.01). UTE-MRI showed nonsignificant correlations with histomorphometry measures. UTE-MRI biomarkers may be useful noninvasive tools for the ACL mechanical assessment.
Asunto(s)
Ligamento Cruzado Anterior , Imagen por Resonancia Magnética , Adulto , Anciano , Ligamento Cruzado Anterior/diagnóstico por imagen , Módulo de Elasticidad , Femenino , Humanos , Imagenología Tridimensional/métodos , Articulación de la Rodilla/diagnóstico por imagen , Imagen por Resonancia Magnética/métodos , Masculino , Persona de Mediana EdadRESUMEN
This study was designed to analyze the effects of type of activity and cruciate ligament resection on knee kinematics and ligament balance after total knee arthroplasty (TKA), and to determine if intraoperative passive kinematics are associated with active kinematics. Fresh-frozen human cadaveric knees were examined. The knees were mounted on a quadriceps-driven simulator. Cruciate-retaining (CR-TKA) and posterior-substituting (PS-TKA) TKA was performed using a contemporary knee system. Active flexion (closed-kinetic chain [CKC] and open-kinetic-chain [OKC]) and passive flexion were analyzed by recording the knee kinematics using a specifically developed application of an imageless navigation system. An electronic ligament balancer was used to measure the tibiofemoral gap under constant distraction pressure. The femur rotated externally relative to the tibia during passive and active CKC flexion. The femur translated anteriorly from 10° to 50° of flexion after TKA. Beyond 50° of flexion, the femur translated posteriorly in all surgical conditions. The femoral location during active CKC flexion was posterior relative to that during active OKC. Femoral rotation and translation during passive knee flexion correlated significantly with that during active knee flexion. Posterior tilt of the electronic ligament balancer was greater with CR-TKA than with PS-TKA and correlated significantly with the anteroposterior position of the femur. Statement of Clinical Significance: Intraoperative knee kinematics measured by computer-assisted navigation and intraoperative ligament balance have the potential to predict postoperative knee kinematics.
Asunto(s)
Artroplastia de Reemplazo de Rodilla , Prótesis de la Rodilla , Fenómenos Biomecánicos , Computadores , Humanos , Articulación de la Rodilla/cirugía , Ligamentos Articulares/cirugía , Rango del Movimiento ArticularRESUMEN
In this study, we combined quantitative ultrashort echo time (UTE) magnetic resonance (MR) imaging and an investigation by a probing device with tri-axial force sensor to seek correlations with mechanical properties of human patellar cartilage for in situ evaluation of biomechanical properties. Cartilage blocks (15 × 20 × 5 mm3) were dissected from the patella of six donors; 5 mm square regions of interest from the cartilage blocks were imaged using UTE-MR imaging sequences (T2* and magnetization transfer ratio (MTR)), and mechanical properties were measured using a micro indentation device. Then, the vertical reaction force on the cartilage surface was measured while push-probing forward 3 mm with the probing device at a 30° tilt to the horizontal plane. The results showed a positive correlation between stiffness/elastic modulus and each predictor variable (UTE-T2* (r = 0.240 and 0.255, respectively, UTE-MTR (r = 0.378 and 0.379, respectively), and probing device force (r = 0.426 and 0.423, respectively). Furthermore, multiple linear regression analysis showed the combination of the three predictors had stronger correlation (adjusted r2 = 0.314 (stiffness), 0.323 (elastic), respectively). Our results demonstrate the potential for these non- and less- invasive methods for in situ evaluation of the mechanical properties of cartilage tissue.
Asunto(s)
Cartílago Articular/diagnóstico por imagen , Imagen por Resonancia Magnética , Fenómenos Biomecánicos , Módulo de Elasticidad , HumanosRESUMEN
OBJECTIVE: Mouse models are commonly used in research applications due to the relatively low cost, highly characterized strains, as well as the availability of many genetically modified phenotypes. In this study, we characterized an ex vivo murine osteochondral repair model using human infrapatellar fat pad (IPFP) progenitor cells. DESIGN: Femurs from euthanized mice were removed and clamped in a custom multidirectional vise to create cylindrical osteochondral defects 0.5 mm in diameter and 0.5 mm deep in both condyles. The IPFP contains progenitors that are a promising cell source for the repair of osteochondral defects. For proof of concept, human IPFP-derived progenitor cells, from osteoarthritic (OA) patients, cultured as pellets, were implanted into the defects and cultured in serum-free medium with TGFß3 for 3 weeks and then processed for histology and immunostaining. RESULTS: The custom multidirectional vise enabled reproducible creation of osteochondral defects in murine femoral condyles. Implantation of IPFP-derived progenitor cells led to development of cartilaginous tissue with Safranin O staining and deposition of collagen type II in the extracellular matrix. CONCLUSIONS: We showed feasibility in creating ex vivo osteochondral defects and demonstrated the regenerative potential of OA human IPFP-derived progenitors in mouse femurs. The murine model can be used to study the effects of aging and OA on tissue regeneration and to explore molecular mechanisms of cartilage repair using genetically modified mice.
Asunto(s)
Tejido Adiposo/citología , Enfermedades de los Cartílagos/terapia , Cartílago Articular/trasplante , Trasplante de Células Madre/métodos , Ingeniería de Tejidos/métodos , Animales , Enfermedades de los Cartílagos/etiología , Fémur , Humanos , Ratones , Modelos Biológicos , Rótula/citología , Prueba de Estudio Conceptual , Células MadreRESUMEN
There are various methods for reconstructing the anterior cruciate ligament (ACL) from other muscles or tendons. Initial tension of the reconstructed ACL is one of the key elements affecting postoperative outcomes. However, tension cannot be measured after graft fixation. The only intraoperative assessment is pull probing, which is performed by pulling joint soft tissues with the arthroscopic probe and can be measured quantitatively. Therefore, its value might be used as an alternative value for the mechanical property of the ACL. Using a probing device one author developed to measure the resistance force of soft tissues quantitatively while probing, we measured the resistance force of dissected ACLs and used tensile testing to investigate the correlation between the resistance force and the mechanical property of the ligaments. According to the results, when a certain amount of tension (strain; 16.6%) was applied, its mechanical properties were moderately correlated (r = 0.56 [p = 0.045]) with the probing force. Therefore, the tension of the reconstructed ACL after fixation under real ACL reconstruction surgery can be derived from the value of the probing device.
RESUMEN
Conventional magnetic resonance imaging (MRI) is not capable of detecting signal from the deep cartilage due to its short transverse relaxation time (T2). Moreover, several quantitative MRI techniques are significantly influenced by the magic angle effect. The combinations of ultrashort echo time (UTE) MRI with magnetization transfer (UTE-MT) and Adiabatic T1ρ (UTE-AdiabT1ρ) imaging allow magic angle-insensitive assessments of all regions of articular cartilage. The purpose of this study was to investigate the correlations between quantitative three-dimensional UTE MRI biomarkers and mechanical properties of human tibiofemoral cartilage specimens. In total, 40 human tibiofemoral cartilage specimens were harvested from three male and four female donors (64 ± 18 years old). Cartilage samples were scanned using a series of quantitative 3D UTE Cones T2* (UTE-T2*), T1 (UTE-T1), UTE-AdiabT1ρ, and UTE-MT sequences in a standard knee coil on a clinical 3T scanner. UTE-MT data were acquired with a series of MT powers and frequency offsets to calculate magnetization transfer ratio (MTR), as well as macromolecular fraction (MMF) and macromolecular T2 (T2mm) through modeling. Cartilage stiffness and Hayes elastic modulus were measured using indentation tests. Correlations of 3D UTE Cones MRI measurements in the superficial layer, deep layer, and global regions of interest (ROIs) with mechanical properties were investigated. Cartilage mechanical properties demonstrated highest correlations with UTE measures of the superficial layer of cartilage. AdiabT1ρ, MTR, and MMF in superficial layer ROIs showed significant correlations with Hayes elastic modulus (p < 0.05, R = -0.54, 0.49, and 0.66, respectively). These UTE measures in global ROIs showed significant, though slightly lower, correlations with Hayes elastic modulus (p < 0.05, R = -0.37, 0.52, and 0.60, respectively). Correlations between other UTE MRI measurements (T2*, T1, and T2mm) and mechanical properties were non-significant. The 3D UTE-AdiabT1ρ and UTE-MT sequences were highlighted as promising surrogates for non-invasive assessment of cartilage mechanical properties. MMF from UTE-MT modeling showed the highest correlations with cartilage mechanics.
Asunto(s)
Cartílago Articular , Anciano , Anciano de 80 o más Años , Cartílago Articular/diagnóstico por imagen , Femenino , Humanos , Imagenología Tridimensional , Articulación de la Rodilla/diagnóstico por imagen , Sustancias Macromoleculares , Imagen por Resonancia Magnética , Masculino , Persona de Mediana EdadRESUMEN
Mechanical and microstructural evaluations of cortical bone using ultrashort echo time magnetic resonance imaging (UTE-MRI) have been performed increasingly in recent years. UTE-MRI acquires considerable signal from cortical bone and enables quantitative bone evaluations. Fitting bone apparent transverse magnetization (T2*) decay using a bicomponent model has been regularly performed to estimate bound water (BW) and pore water (PW) in the quantification of bone matrix and porosity, respectively. Human cortical bone possesses a considerable amount of fat, which appears as MRI T2* signal oscillation and can subsequently lead to BW overestimation when using a bicomponent model. Tricomponent T2* fitting model has been developed to improve BW and PW estimations by accounting for fat contribution in the MRI signal. This study aimed to investigate the correlations of microstructural and mechanical properties of human cortical bone with water pool fractions obtained from a tricomponent T2* model. 135 cortical bone strips (~4 × 2 × 40 mm3 ) from tibial and femoral midshafts of 37 donors (61 ± 24 years old) were scanned using ten sets of dual-echo 3D-UTE-Cones sequences (TE = 0.032-24.0 ms) on a 3 T MRI scanner for T2* fitting analyses. Average bone porosity and pore size were measured using microcomputed tomography (µCT) at 9 µm voxel size. Bone mechanical properties were measured using 4-point bending tests. Using a tricomponent model, bound water fraction (FracBW ) showed significant strong (R = 0.70, P < 0.01) and moderate (R = 0.58-0.62, P < 0.01) correlations with porosity and mechanical properties, respectively. Correlations of bone microstructural and mechanical properties with water pool fractions were higher for tricomponent model results compared with the bicomponent model. The tricomponent T2* fitting model is suggested as a useful technique for cortical bone evaluation where the MRI contribution of bone fat is accounted for.
Asunto(s)
Hueso Cortical/diagnóstico por imagen , Hueso Cortical/fisiología , Imagen por Resonancia Magnética , Protones , Agua/química , Fenómenos Biomecánicos , Femenino , Humanos , Modelos Lineales , Masculino , Persona de Mediana Edad , Factores de Tiempo , Microtomografía por Rayos XRESUMEN
Purpose: Scaffold-free cartilage tissue engineering circumvents issues with scaffold seeding, potential toxicity response, and impaired host integration. However, precisely controlling and maintaining a scaffold-free construct shape have been challenging. We explored the feasibility of microneedle arrays to print tissue using cellular microspheroids as building blocks.Materials and Methods: Human embryonic-derived mesenchymal stem cells or infrapatellar fat pad mesenchymal stem cells were used to create microspheroids of 500 µm in diameter, which were assembled on microneedle arrays in a predefined arrangement using a robotic system under computer vision. Microspheroids on microneedles were cultured to permit fusion into a tissue construct. Infrapatellar fat pad mesenchymal stem cell constructs were either implanted into chondral defects created in human osteoarthritic cartilage explants or maintained on the microneedle array for 3 weeks. Embryonic-derived mesenchymal stem cell constructs were designed to be press-fit into 3 mm subchondral defects in New Zealand White rabbits and maintained for up to 8 weeks to assess retention, early tissue repair, and more mature cartilage regeneration.Results: Microspheroids of both cell types fused together in culture to form neotissues of predefined shape and size. Infrapatellar fat pad mesenchymal stem cell neotissues expressed high levels of chondrogenic genes and integrated with the surrounding osteoarthritic host cartilage. Embryonic-derived mesenchymal stem cell constructs generated chondrogenic neotissue in vivo as early as 2 weeks and more mature tissue by 8 weeks with increased glycosaminoglycan deposition.Conclusions: We constructed defined scaffold-free shapes by bioprinting and fusing microspheroids. Proof of concept was shown in the repair of ex vivo osteoarthritic human cartilage and in vivo rabbit osteochondral (OC) defects.
Asunto(s)
Cartílago , Condrogénesis , Células Madre Embrionarias Humanas/metabolismo , Trasplante de Células Madre Mesenquimatosas , Células Madre Mesenquimatosas/metabolismo , Osteoartritis , Procedimientos Quirúrgicos Robotizados , Ingeniería de Tejidos , Anciano , Animales , Cartílago/lesiones , Cartílago/metabolismo , Cartílago/patología , Femenino , Células Madre Embrionarias Humanas/patología , Humanos , Masculino , Células Madre Mesenquimatosas/patología , Persona de Mediana Edad , Agujas , Osteoartritis/metabolismo , Osteoartritis/patología , Osteoartritis/terapia , ConejosRESUMEN
Cortical bone shows as a signal void when using conventional clinical magnetic resonance imaging (MRI). Ultrashort echo time MRI (UTE-MRI) can acquire high signal from cortical bone, thus enabling quantitative assessments. Magnetization transfer (MT) imaging combined with UTE-MRI can indirectly assess protons in the organic matrix of bone. This study aimed to examine UTE-MT MRI techniques to estimate the mechanical properties of cortical bone. A total of 156 rectangular human cortical bone strips were harvested from the tibial and femoral midshafts of 43 donors (62⯱â¯22â¯years old, 62 specimens from females, 94 specimens from males). Bone specimens were scanned using UTE-MT sequences on a clinical 3â¯T MRI scanner and on a micro-computed tomography (µCT) scanner. A series of MT pulse saturation powers (400°, 600°, 800°) and frequency offsets (2, 5, 10, 20, 50â¯kHz) was used to measure the macromolecular fraction (MMF) utilizing a two-pool MT model. Failure mechanical properties of the bone specimens were measured using 4-point bending tests. MMF from MRI results showed significant strong correlations with cortical bone porosity (Râ¯=â¯-0.72, Pâ¯<â¯0.01) and bone mineral density (BMD) (Râ¯=â¯+0.71, Pâ¯<â¯0.01). MMF demonstrated significant moderate correlations with Young modulus, yield stress, and ultimate stress (Râ¯=â¯0.60-0.61, Pâ¯<â¯0.01). These results suggest that the two-pool UTE-MT model focusing on the organic matrix of bone can potentially serve as a novel tool to detect the variations of bone mechanical properties and intracortical porosity.
RESUMEN
Entheses are regions where tendons and ligaments attach to bone, and are the primary target in seronegative and other diseases of the musculoskeletal (MSK) system. MRI has been widely used for visualizing features of inflammatory and degenerative MSK disease; however, normal tendons and entheses have short transverse relaxation times (T2 ), and show little or no signal with conventional clinical MRI pulse sequences, making it difficult to investigate their MR properties. In this study we examined the normal MR morphology of the cadaveric Achilles tendon and enthesis at 3 T using novel three-dimensional ultrashort echo time (3D UTE) Cones sequences, and at 11.7 T using conventional MRI sequences. We also studied the MR properties of the Achilles tendon and enthesis including T2 *, T1 , and magnetization transfer ratio (MTR). In addition, MT modeling of macromolecular proton fractions was investigated using 3D UTE Cones sequences at 3 T. Indentation testing was performed to investigate the mechanical properties of the tendons and entheses, and this was followed by histological examination. In total five specimens (<50 years) were investigated. On average, tendons and entheses respectively had T2 * values of 0.93 ± 0.48 ms and 2.77 ± 0.79 ms, T1 values of 644 ± 22 ms and 780 ± 55 ms, MTRs of 0.373 ± 0.03 and 0.244 ± 0.009 with an MT power of 1000° and frequency offset of 2 kHz, and macromolecular proton fractions of 18.0 ± 2.2% and 13.9 ± 1.9%. Compared with the tendon, the enthesis generally had a longer T2 *, a longer T1 , a lower MTR, and a lower macromolecular proton fraction as well as both a higher Young's modulus and stiffness. Results from this study are likely to provide a useful baseline for identifying deviations from the normal in seronegative arthritis and other disease of the entheses.
Asunto(s)
Tendón Calcáneo/diagnóstico por imagen , Imagen por Resonancia Magnética , Adulto , Fenómenos Biomecánicos , Cadáver , Femenino , Humanos , Imagenología Tridimensional , Masculino , Factores de TiempoRESUMEN
Bone stress injury (BSI) incidents have been increasing amongst athletes in recent years as a result of more intense sporting activities. Cortical bone in the tibia and fibula is one of the most common BSI sites. Nowadays, clinical magnetic resonance imaging (MRI) is the recommended technique for BSI diagnosis at an early stage. However, clinical MRI focuses on edema observations in surrounding soft tissues, rather than the injured components of the bone. Specifically, both normal and injured bone are invisible in conventional clinical MRI. In contrast, ultrashort echo time (UTE)-MRI is able to detect the rapidly decaying signal from the bone. This study aimed to employ UTE-MRI for fatigue fracture detection in fibula cortical bone through an ex vivo investigation. Fourteen human fibular samples (47 ± 20 years old, four women) were subjected to cyclic loading on a four-point bending setup. The loading was displacement controlled to induce -5000 ± 1500 µ-strain at 4 Hz. Loading was stopped when bone stiffness was reduced by 20%. Fibula samples were imaged twice, using UTE-MRI and micro-computed tomography (µCT), first pre-loading and second post-loading. After loading, the macromolecular fraction (MMF) from UTE-MT modeling demonstrated a significant decrease (12% ± 20%, P = 0.02) on average. Single-component T2 * also decreased significantly by BSI (12% ± 11%, P = 0.01) on average. MMF reduction is hypothesized to be a result of collagenous matrix rupture and water increase. However, faster T2 * decay might be a result of water shifts towards newly developed microcracks with higher susceptibility. Despite this good sensitivity level of the UTE-MRI technique, the µCT-based porosity at a voxel size of 9 µm was not affected by loading. UTE-MRI shows promise as a new quantitative technique to detect BSI.
Asunto(s)
Hueso Cortical/diagnóstico por imagen , Hueso Cortical/patología , Peroné/diagnóstico por imagen , Peroné/patología , Fracturas por Estrés/diagnóstico por imagen , Fracturas por Estrés/diagnóstico , Imagen por Resonancia Magnética , Femenino , Humanos , Masculino , Persona de Mediana Edad , Factores de Tiempo , Soporte de PesoRESUMEN
Retinal ganglion cells (RGCs) are responsible for the transfer of signals from the retina to the brain. As part of the central nervous system, RGCs are unable to regenerate following injury, and implanted cells have limited capacity to orient and integrate in vivo. During development, secreted guidance molecules along with signals from extracellular matrix and the vasculature guide cell positioning, for example, around the fovea, and axon outgrowth; however, these changes are temporally regulated and are not the same in the adult. Here, we combine electrospun cell transplantation scaffolds capable of RGC neurite guidance with thermal inkjet 3D cell printing techniques capable of precise positioning of RGCs on the scaffold surface. Optimal printing parameters are developed for viability, electrophysiological function and, neurite pathfinding. Different media, commonly used to promote RGC survival and growth, were tested under varying conditions. When printed in growth media containing both brain-derived neurotrophic factor (BDNF) and ciliary neurotrophic factor (CNTF), RGCs maintained survival and normal electrophysiological function, and displayed radial axon outgrowth when printed onto electrospun scaffolds. These results demonstrate that 3D printing technology may be combined with complex electrospun surfaces in the design of future retinal models or therapies.