A Scalable Robust Microporous Al-MOF for Post-Combustion Carbon Capture.

Herein, a robust microporous aluminum tetracarboxylate framework, MIL-120(Al)-AP, (MIL, AP: Institute Lavoisier and Ambient Pressure synthesis, respectively) is reported, which exhibits high CO2 uptake (1.9 mmol g-1 at 0.1 bar, 298 K). In situ Synchrotron X-ray diffraction measurements together with Monte Carlo simulations reveal that this structure offers a favorable CO2 capture configuration with the pores being decorated with a high density of µ2-OH groups and accessible aromatic rings. Meanwhile, based on calculations and experimental evidence, moderate host-guest interactions Qst (CO2) value of MIL-120(Al)-AP (-40 kJ mol-1) is deduced, suggesting a relatively low energy penalty for full regeneration. Moreover, an environmentally friendly ambient pressure green route, relying on inexpensive raw materials, is developed to prepare MIL-120(Al)-AP at the kilogram scale with a high yield while the Metal- Organic Framework (MOF) is further shaped with inorganic binders as millimeter-sized mechanically stable beads. First evidences of its efficient CO2/N2 separation ability are validated by breakthrough experiments while operando IR experiments indicate a kinetically favorable CO2 adsorption over water. Finally, a techno-economic analysis gives an estimated production cost of ≈ 13 $ kg-1, significantly lower than for other benchmark MOFs. These advancements make MIL-120(Al)-AP an excellent candidate as an adsorbent for industrial-scale CO2 capture processes.

When Polymorphism in Metal-Organic Frameworks Enables Water Sorption Profile Tunability for Enhancing Heat Allocation and Water Harvesting Performance.

The development of thermally driven water-sorption-based technologies relies on high-performing water vapor adsorbents. Here, polymorphism in Al-metal-organic frameworks is disclosed as a new strategy to tune the hydrophilicity of MOFs. This involves the formation of MOFs built from chains of either trans- or cis- µ-OH-connected corner-sharing AlO4(OH)2 octahedra. Specifically, [Al(OH)(muc)] or MIP-211, is made of trans, trans-muconate linkers, and cis-µ-OH-connected corner-sharing AlO4(OH)2 octahedra giving a 3D network with sinusoidal channels. The polymorph MIL-53-muc has a tiny change in the chain structure that results in a shift of the step position of the water isotherm from P/P0 ≈ 0.5 in MIL-53-muc, to P/P0 ≈ 0.3 in MIP-211. Solid-state NMR and Grand Canonical Monte Carlo reveal that the adsorption occurs initially between two hydroxyl groups of the chains, favored by the cis-positioning in MIP-211, resulting in a more hydrophilic behavior. Finally, theoretical evaluations show that MIP-211 would allow achieving a coefficient of performance for cooling (COPc) of 0.63 with an ultralow driving temperature of 60 °C, outperforming benchmark sorbents for small temperature lifts. Combined with its high stability, easy regeneration, huge water uptake capacity, green synthesis, MIP-211 is among the best adsorbents for adsorption-driven air conditioning and water harvesting from the air.

A robust ultra-microporous cationic aluminum-based metal-organic framework with a flexible tetra-carboxylate linker.

Al-based cationic metal-organic frameworks (MOFs) are uncommon. Here, we report a cationic Al-MOF, MIP-213(Al) ([Al18(µ2-OH)24(OH2)12(mdip)6]6Cl·6H2O) constructed from flexible tetra-carboxylate ligand (5,5'-Methylenediisophthalic acid; H4mdip). Its crystal structure was determined by the combination of three-dimensional electron diffraction (3DED) and high-resolution powder X-ray diffraction. The structure is built from infinite corner-sharing chains of AlO4(OH)2 and AlO2(OH)3(H2O) octahedra forming an 18-membered rings honeycomb lattice, similar to that of MIL-96(Al), a scarce Al-polycarboxylate defective MOF. Despite sharing these structural similarities, MIP-213(Al), unlike MIL-96(Al), lacks the isolated µ3-oxo-bridged Al-clusters. This leads to an ordered defective cationic framework whose charge is balanced by Cl- sandwiched between two Al-trimers at the corner of the honeycomb, showing strong interaction with terminal H2O coordinated to the Al-trimers. The overall structure is endowed by a narrow quasi-1D channel of dimension ~4.7 Å. The Cl- in the framework restrains the accessibility of the channels, while the MOF selectively adsorbs CO2 over N2 and possesses high hydrolytic stability.

Polymer-metal-organic framework self-assembly (PMOFSA) as a robust one-step method to generate well-dispersed hybrid nanoparticles in water.

A new process, PMOFSA, is described here, that opens the way for the one-pot straightforward and versatile manufacture of polymer-MOF nanoparticles in water. It can be expected that this study will not only expand the scope of in situ preparation of polymer-MOF nano-objects but also inspire researchers in the field to prepare a new generation of polymer-MOF hybrid materials.

Structural insight into the magnesium borohydride - ethylenediamine solid-state Mg-ion electrolyte system.

A highly complex crystal structure of stoichiometric Mg5(en)6(BH4)10 was solved from single crystal synchrotron X-ray diffraction and confirmed by neutron powder diffraction (NPD) on isotopically substituted Mg(en)1.2(11BD4)2. We highlight the role of the amorphous Mg(BH4)2 in the reactivity of the Mg(BH4)2-en system and characterized a previously overlooked phase, Mg(en)2(BH4)2.

Deciphering the Role of Water in Promoting the Optoelectronic Performance of Surface-Engineered Lead Halide Perovskite Nanocrystals.

Lead halide perovskites are promising candidates for high-performance light-emitting diodes (LEDs); however, their applicability is limited by their structural instability toward moisture. Although a deliberate addition of water to the precursor solution has recently been shown to improve the crystallinity and optical properties of perovskites, the corresponding thin films still do not exhibit a near-unity quantum yield. Herein, we report that the direct addition of a minute amount of water to post-treated formamidinium lead bromide (FAPbBr3) nanocrystals (NCs) substantially enhances the stability while achieving a 95% photoluminescence quantum yield in a NC thin film. We unveil the mechanism of how moisture assists in the formation of an additional NH4Br component. Alongside, we demonstrate the crucial role of moisture in assisting localized etching of the perovskite crystal, facilitating the partial incorporation of NH4+, which is key for improved performance under ambient conditions. Finally, as a proof-of-concept, the application of post-treated and water-treated perovskites is tested in LEDs, with the latter exhibiting a superior performance, offering opportunities toward commercial application in moisture-stable optoelectronics.

Real-time regeneration of a working zeolite monitored via operando X-ray diffraction and crystallographic imaging: how coke flees the MFI framework.

We have monitored the regeneration of H-ZSM-5 via operando time-resolved powder X-Ray diffraction (PXRD) coupled with mass spectroscopy (MS). Parametric Rietveld refinements and calculation of the extra-framework electronic density by differential Fourier maps analysis provide details on the mode of coke removal combined with the corresponding sub-unit cell changes of the zeolite structure. It is clear that the coke removal is a complex process that occurs in at least two steps; a thermal decomposition followed by oxidation. In a coked zeolite, the straight 10-ring channel circumference is warped to an oval shape due to structural distortion induced by rigid aromatic coke species. The data presented explain why the difference in length between the a-vector and the b-vector of the MFI unit cell is a robust descriptor for bulky coke, as opposed to the unit cell volume, which is affected also by adsorbed species and thermal effects. Our approach holds the promise to quantify and identify coke removal (and formation) in structurally distinct locations within the zeolite framework.

A zirconium metal-organic framework with SOC topological net for catalytic peptide bond hydrolysis.

The discovery of nanozymes for selective fragmentation of proteins would boost the emerging areas of modern proteomics, however, the development of efficient and reusable artificial catalysts for peptide bond hydrolysis is challenging. Here we report the catalytic properties of a zirconium metal-organic framework, MIP-201, in promoting peptide bond hydrolysis in a simple dipeptide, as well as in horse-heart myoglobin (Mb) protein that consists of 153 amino acids. We demonstrate that MIP-201 features excellent catalytic activity and selectivity, good tolerance toward reaction conditions covering a wide range of pH values, and importantly, exceptional recycling ability associated with easy regeneration process. Taking into account the catalytic performance of MIP-201 and its other advantages such as 6-connected Zr6 cluster active sites, the green, scalable and cost-effective synthesis, and good chemical and architectural stability, our findings suggest that MIP-201 may be a promising and practical alternative to commercially available catalysts for peptide bond hydrolysis.

An Orthorhombic Modification of KCoPO4 Stabilized under Hydrothermal Conditions: Crystal Chemistry and Magnetic Behavior.

A novel modification of the KCoPO4, δ-phase has been prepared by hydrothermal synthesis at 553 K. The compound crystallizes in the orthorhombic system with the unit-cell parameters a = 8.5031(8), b = 10.2830(5), c = 54.170(4) Å. The crystal structure was determined based on synchrotron low-temperature single-crystal X-ray diffraction data obtained from an inversion twin in the space group P212121 and refined to R = 0.077 for 5156 reflections with I > 3σ(I). The δ-KCoPO4 possesses a new structure type which is based on a framework built from sharing vertices Co- and P-centered tetrahedra. The {CoPO4-}∞ construction of tetrahedra may be described as assembled from networks formed by two topologically diverse six-membered rings of tetrahedra stacked together through vertex-bridging contacts along the a axis. The ratio of the (UUUDDD) and (UUDUDD) rings, where (U) and (D) denote the orientation of the tetrahedra in the six-membered rings up and down relative to the plane grids, is equal to 5:1. The (UUDUDD) rings form bands parallel to the [010] direction each surrounded from both sides along the c axis by slabs of five ribbons width having alternative (UUUDDD) topology. Open in the [100] direction channels incorporate K+ ions; this structural feature permits to suppose ion-conductive and/or electrochemical properties of the title compound. The possible mechanism of the δ → γ phase transition is discussed on the basis of the crystal chemical analysis of the KCoPO4 polymorphs. The title compound orders magnetically at TN = 24.8 K.

Kinetic Barriers and Microscopic Mechanisms of Noble Gas Adsorption by Nanoporous γ-Mg(BH4 )2 Obtained by Means of Sub-Second X-Ray Diffraction.

Gas adsorption by porous frameworks sometimes results in structure "breathing", "pores opening/closing", "negative gas adsorption", and other phenomena. Time-dependent diffraction can address both kinetics of the guest uptake and structural response of the host framework. Using sub-second in situ powder X-ray diffraction, three intracrystalline diffusion scenarios have been evaluated from the isothermal kinetics of Ar, Kr, and Xe adsorption by nanoporous γ-Mg(BH4 )2 . These scenarios are dictated by two possible simultaneous transport mechanisms: diffusion through the intra- (i) and interchannel apertures (ii) of γ-Mg(BH4 )2 crystal structure. The contribution of (i) and (ii) changes depending on the kinetic diameter of the noble gas molecule and temperature regime. The lowest single activation barrier for the smallest Ar suggests equal diffusion of the atoms trough both pathways. Contrary, for the medium sized Kr we resolve the contributions of two parallel transport mechanisms, which tentatively can be attributed to the smaller barrier of the migration paths via the channel like pores and the higher barrier for the diffusion via narrow aperture between these channels. The largest Xe atoms diffuse only along 1D channels and show the highest single activation barrier.

Metal-organic magnets with large coercivity and ordering temperatures up to 242°C.

Magnets derived from inorganic materials (e.g., oxides, rare-earth-based, and intermetallic compounds) are key components of modern technological applications. Despite considerable success in a broad range of applications, these inorganic magnets suffer several drawbacks, including energetically expensive fabrication, limited availability of certain constituent elements, high density, and poor scope for chemical tunability. A promising design strategy for next-generation magnets relies on the versatile coordination chemistry of abundant metal ions and inexpensive organic ligands. Following this approach, we report the general, simple, and efficient synthesis of lightweight, molecule-based magnets by postsynthetic reduction of preassembled coordination networks that incorporate chromium metal ions and pyrazine building blocks. The resulting metal-organic ferrimagnets feature critical temperatures up to 242°C and a 7500-oersted room-temperature coercivity.

Discovery of new boron-rich chalcogenides: orthorhombic B6X (X=S, Se).

New boron-rich sulfide B6S and selenide B6Se have been discovered by combination of high pressure - high temperature synthesis and ab initio evolutionary crystal structure prediction, and studied by synchrotron X-ray diffraction and Raman spectroscopy at ambient conditions. As it follows from Rietveld refinement of powder X-ray diffraction data, both chalcogenides have orthorhombic symmetry and belong to Pmna space group. All experimentally observed Raman bands have been attributed to the theoretically calculated phonon modes, and the mode assignment has been performed. Prediction of mechanical properties (hardness and elastic moduli) of new boron-rich chalcogenides has been made using ab initio calculations, and both compounds were found to be members of a family of hard phases.

Non-Isothermal Kinetics of Kr Adsorption by Nanoporous γ-Mg(BH4)2 from in Situ Synchrotron Powder Diffraction.

Crystalline materials with pore dimensions comparable to the kinetic diameters of the guest molecules are attractive for their potential use in adsorption and separation applications. The nanoporous γ-Mg(BH4)2 features one-dimensional channels matching this criterion for Kr uptake, which has been probed using synchrotron powder diffraction at various pressures and temperatures. It results in two coexisting crystalline phases with the limiting composition Mg(BH4)2·0.66Kr expecting the highest Kr content (50.7 wt % in the crystalline phase) reported for porous materials. Quasi-equilibrium isobars built from Rietveld refinements of Kr site occupancies were rationalized with a noncooperative lattice gas model, yielding the values of the thermodynamic parameters. The latter were independently confirmed from Kr fluorescence. We have also parameterized the pronounced kinetic hysteresis with a modified mean-field model adopted for the Arrhenius kinetics.

Thermal unequilibrium of strained black CsPbI3 thin films.

The high-temperature, all-inorganic CsPbI3 perovskite black phase is metastable relative to its yellow, nonperovskite phase at room temperature. Because only the black phase is optically active, this represents an impediment for the use of CsPbI3 in optoelectronic devices. We report the use of substrate clamping and biaxial strain to render black-phase CsPbI3 thin films stable at room temperature. We used synchrotron-based, grazing incidence, wide-angle x-ray scattering to track the introduction of crystal distortions and strain-driven texture formation within black CsPbI3 thin films when they were cooled after annealing at 330°C. The thermal stability of black CsPbI3 thin films is vastly improved by the strained interface, a response verified by ab initio thermodynamic modeling.

Complexation of Ammonia Boranes with Al3.

Ammonia borane, NH3BH3 (AB), is very attractive for hydrogen storage; however, it dehydrogenates exothermally, producing a mixture of polymeric products with limited potential for direct rehydrogenation. Recently, it was shown that AB complexed with Al3+ in Al(BH4)3·AB endothermically dehydrogenates to a single product identified as Al(BH4)3·NHBH, with the potential for direct rehydrogenation of AB. Here we explore the reactivity of AB-derived RNH2BH3 (R = -CH3, -CH2-) with AlX3 salts (X = BH4-, Cl-), aiming to extend the series to different anions and to enlarge the stability window for Al(BH4)3·NRBH. Three novel complexes were identified: Al(BH4)3·CH3NH2BH3 having a molecular structure similar to that of Al(BH4)3·AB but different dehydrogenation properties, as well as [Al(CH3NH2BH3)2Cl2][AlCl4] and [Al(NH2CH2CH2NH2)(BH4)2][Al(BH4)4], rare examples of Al3+ making part of the cations and anions simultaneously. The latter compounds are of interest in the design of novel electrolytes for Al-based batteries. The coordination of two ABs to a single Al atom opens a route to materials with higher hydrogen content.

Biporous Metal-Organic Framework with Tunable CO2/CH4 Separation Performance Facilitated by Intrinsic Flexibility.

In this work, we report the synthesis of SION-8, a novel metal-organic framework (MOF) based on Ca(II) and a tetracarboxylate ligand TBAPy4- endowed with two chemically distinct types of pores characterized by their hydrophobic and hydrophilic properties. By altering the activation conditions, we gained access to two bulk materials: the fully activated SION-8F and the partially activated SION-8P with exclusively the hydrophobic pores activated. SION-8P shows high affinity for both CO2 ( Qst = 28.4 kJ/mol) and CH4 ( Qst = 21.4 kJ/mol), while upon full activation, the difference in affinity for CO2 ( Qst = 23.4 kJ/mol) and CH4 ( Qst = 16.0 kJ/mol) is more pronounced. The intrinsic flexibility of both materials results in complex adsorption behavior and greater adsorption of gas molecules than if the materials were rigid. Their CO2/CH4 separation performance was tested in fixed-bed breakthrough experiments using binary gas mixtures of different compositions and rationalized in terms of molecular interactions. SION-8F showed a 40-160% increase (depending on the temperature and the gas mixture composition probed) of the CO2/CH4 dynamic breakthrough selectivity compared to SION-8P, demonstrating the possibility to rationally tune the separation performance of a single MOF by manipulating the stepwise activation made possible by the MOF's biporous nature.

Structure and thermoelectric properties of the silver lead bismuth selenides Ag5Pb9Bi19Se40 and AgPb3Bi7Se14.

In the system Ag/Pb/Bi/Se, two new thermoelectric phases derived from lillianite (Pb3Bi2S6) have been characterized. The crystal structures correspond to the 8,8L- and 5,5L-types, respectively, both in the space group Cmcm. The room-temperature unit-cell parameters of 8,8L-Ag5Pb9Bi19Se40 are a = 4.2151(8) Å, b = 13.951(3) Å and c = 35.284(7) Å and those of 5,5L-AgPb3Bi7Se14 are a = 4.2337(8) Å, b = 13.864(2) Å and c = 24.653(3) Å. The temperature-dependent evolution of the lattice parameters of Ag5Pb9Bi19Se40 becomes steeper at temperatures above 300 °C and hints at the mobility of Ag+ ions. Samples containing both phases exhibit thermoelectric figures of merit up to ZT = 0.23 at 250 °C. HRTEM investigations on such samples showed well-ordered areas of the lillianite-like phases separated by large slabs that exhibit a high concentration of defects and may compensate for lattice misfits between the lillianite-type phases.

Deactivation of Zeolite Catalyst H-ZSM-5 during Conversion of Methanol to Gasoline: Operando Time- and Space-Resolved X-ray Diffraction.

The deactivation of zeolite catalyst H-ZSM-5 by coking during the conversion of methanol to hydrocarbons was monitored by high-energy space- and time-resolved operando X-ray diffraction (XRD) . Space resolution was achieved by continuous scanning along the axial length of a capillary fixed bed reactor with a time resolution of 10 s per scan. Using real structural parameters obtained from XRD, we can track the development of coke at different points in the reactor and link this to a kinetic model to correlate catalyst deactivation with structural changes occurring in the material. The "burning cigar" model of catalyst bed deactivation is directly observed in real time.

Solid Aluminum Borohydrides for Prospective Hydrogen Storage.

Metal borohydrides are intensively researched as high-capacity hydrogen storage materials. Aluminum is a cheap, light, and abundant element and Al3+ can serve as a template for reversible dehydrogenation. However, Al(BH4 )3 , containing 16.9 wt % of hydrogen, has a low boiling point, is explosive on air and has poor storage stability. A new family of mixed-cation borohydrides M[Al(BH4 )4 ], which are all solid under ambient conditions, show diverse thermal decomposition behaviors: Al(BH4 )3 is released for M=Li+ or Na+ , whereas heavier derivatives evolve hydrogen and diborane. NH4 [Al(BH4 )4 ], containing both protic and hydridic hydrogen, has the lowest decomposition temperature of 35 °C and yields Al(BH4 )3 ⋅NHBH and hydrogen. The decomposition temperatures, correlated with the cations' ionic potential, show that M[Al(BH4 )4 ] species are in the most practical stability window. This family of solids, with convenient and versatile properties, puts aluminum borohydride chemistry in the mainstream of hydrogen storage research, for example, for the development of reactive hydride composites with increased hydrogen content.

Cooperative Adsorption by Porous Frameworks: Diffraction Experiment and Phenomenological Theory.

Materials science of metal open frameworks is a state-of-the-art field for numerous applications, such as gas storage, sensors, and medicine. Two nanoporous frameworks, γ-Mg(BH4 )2 and MIL-91(Ti), with different levels of structural flexibility, were examined with in situ X-ray diffraction guest adsorption-desorption experiments. Both frameworks exhibit a cooperative guest adsorption correlated with a lattice deformation. This cooperativity originates from the long-range interactions between guest molecules, mediated by elastic response of the host porous structure. The observed experimental scenarios are rationalized with a mean field Gorsky-Bragg-Williams (GBW) approach for the lattice-gas Ising model. The adjusted GBW model, in combination with in situ synchrotron powder diffraction, demonstrates an efficient experimental and phenomenological approach to characterize thermodynamics of the adsorption in MOFs not only for the total uptake but also for every specific guest site.