Suture anchor repair yields better biomechanical properties than transosseous sutures in ruptured quadriceps tendons.

PURPOSE: This human cadaveric study compares the biomechanical properties of quadriceps tendon repair with suture anchors and the commonly applied transosseous sutures. The hypothesis was that suture anchors provide at least equal results concerning gap formation and ultimate failure load compared with transosseous suture repair. METHODS: Thirty human cadaveric knees underwent tenotomy followed by repair with either 5.5-mm-double-loaded suture anchors [titanium (TA) vs. resorbable hydroxyapatite (HA)] or transpatellar suture tunnels using No. 2 Ultrabraid™ and the Krackow whipstitch. Biomechanical analysis included pretensioning the constructs with 20 N for 30 s and then cyclic loading of 250 cycles between 20 and 100 N at 1 Hz in a servohydraulic testing machine with measurement of elongation. Ultimate failure load analysis and failure mode analysis were performed subsequently. RESULTS: Tendon repairs with suture anchors yielded significantly less gap formation during cyclic loading (20th-250th cycle: TA 1.9 ± 0.1, HA 1.5 ± 0.5, TS 33.3 ± 1.9 mm, p < 0.05) and resisted significantly higher ultimate failure loads (TA 740 ± 204 N, HA 572 ± 67 N, TS 338 ± 60 N, p < 0.05) compared with transosseous sutures. Common failure mode was pull-out of the eyelet within the suture anchor in the HA group and rupture of the suture in the TA and TS group. CONCLUSION: Quadriceps tendon repair with suture anchors yields significantly better biomechanical results than the commonly applied transosseous sutures in this human cadaveric study. These biomechanical findings may change the future clinical treatment for quadriceps tendon ruptures. Randomised controlled clinical trials are desirable for the future. LEVEL OF EVIDENCE: Not applicable, controlled laboratory human cadaveric study.

[Ligament bracing--augmented cruciate ligament sutures: biomechanical studies of a new treatment concept]. / "Ligament bracing"--die augmentierte Kreuzbandnaht: Biomechanische Grundlagen für ein neues Behandlungskonzept.

BACKGROUND: In the context of acute knee dislocations, suture repair of ruptured cruciate ligaments leads to good clinical results in 80% of cases. Disadvantages are low primary stability and subsequently secondary elongation of the sutured ligaments. In the present study, we compared primary stability of suture repair, reinforced by different suture augments, to cruciate ligament reconstruction. OBJECTIVE: The concept of ligament bracing with transosseous suture repair of the cruciate ligaments and additional suture augmentation is biomechanically superior to cruciate ligament reconstruction. MATERIAL AND METHODS: A total of 42 porcine knee joints divided into seven groups were examined. The stability of four different suture/augmentation combinations were compared to cruciate ligament reconstruction with human hamstring tendons. The investigational setup consisted of testing 1000 cycles with 20 N to 154 N load in a.-p. translation and 60° flexion. Elongation and load to failure were measured. RESULTS: Neither reconstruction (3.13 ± 1.65 mm; 362 ± 51 N) nor augmented suture repair (1.89-2.5 mm; 464-624 N) achieved the primary stability of the intact cruciate ligament (0.63 ± 0.34 mm, 1012 ± 91 N). In comparison to ligament reconstruction, all four augmented suture repairs showed minor elongation in the cyclic test and a higher load to failure. The isolated suture repair showed poor results (6.79 ± 4.86 mm, 177 ± 73 N). CONCLUSION: Augmented suture repair provides significantly higher stability compared with isolated suture repair and reconstruction with hamstring tendons. The concept of ligament bracing could be a promising future treatment option in acute knee dislocations. Clinical results remain to be seen.

Biomechanical properties of femoral posterior cruciate ligament fixations.

PURPOSE: The success of reconstructions of the posterior cruciate ligament (PCL) mainly depends on the fixation strength of the tendon-bone interface. Reliable data about the mechanical characteristics of PCL fixation techniques are sparse. The aim of this study was to investigate the biomechanical properties of different femoral PCL fixation techniques. METHODS: Fresh human cadaver quadriceps (Q) and hamstring (H) tendons were harvested and fixed into porcine femora with a press-fit fixation suturing the tendon over a bone bridge (group A), a novel implant post-fixation (group B) or an interference screw fixation (group C). Each group consisted of 10 specimens. The constructs were cyclically stretched and eventually loaded until failure. Elongation during cyclic loading, stiffness, failure mode and maximum failure load was evaluated. RESULTS: Elongation during cyclical loading was significantly larger between the 1st and the 20th cycle than between the 20th and the 500th cycle in all groups (p < 0.05). Maximum failure load was 409 ± 71 (336-517) N in group QA, 456 ± 58 (347-510) N in group QB, 548 ± 116 (400-798) N in group QC, 472 ± 114 N (316-676 N) in group HA, 494 ± 98 N (371-668 N) in group HB and 498 ± 87 N (391-687 N) in group HC (significantly higher for QB compared to QA, p < 0.05). CONCLUSION: This is the first study investigating the biomechanical properties of femoral PCL fixations. Implant-free fixation techniques like press-fit or post-fixations are able to withstand equal biomechanical forces compared to interference screw fixation. The novel fixations described in this study can be considered as a reliable alternative for the reconstruction of PCL using either hamstring or quadriceps tendons.

Comparison of three suture techniques and three suture materials on gap formation and failure load in ruptured tendons: a human cadaveric study.

INTRODUCTION: There is a large variety of ruptures of tendons and ligaments in trauma surgery. Reliable data about the most appropriate suture technique and suture material for ruptured tendons are sparse. This human cadaveric study compares the biomechanical properties of three suture materials and three suture techniques for semitendinosus tendon repair. METHOD: Sixty-three human cadaver hamstring tendons underwent tenotomy and repair with either Baseball suture, Kessler suture, or a novel "Hannover" suture, using either PDS 2-0, Ethibond 2-0, or Fiberwire 2-0. Biomechanical analysis included pretensioning the constructs with 2 N for 50 s, then cyclic loading of 500 cycles between 2 and 15 N at 1 Hz in a servohydraulic testing machine with measurement of elongation. After this, ultimate failure load and failure mode analysis was performed. RESULTS: Ruptures repaired by Fiberwire™ as suture material and the Baseball suture technique were able to withstand significantly higher maximum failure loads (72.8 ± 22.0 N, p < 0.001) than the Kessler suture and the Hannover suture, while ruptures repaired by Fiberwire and the Kessler suture technique showed the lowest elongation after cyclic loading (14.6 ± 3.8 mm, p = 0.15). CONCLUSION: These findings may be of relevance for the future clinical treatment of tendon ruptures. Further in vivo clinical application studies are desirable for the future.