Janus metallic film with gold and silver luster by electroless deposition of silver using poly(dopamine acrylamide) thin film.

Films that exhibit different metallic luster on the front and back, called Janus metallic films, have broad applications ranging from design materials to optical devices. However, the fabrication of these films is often a complicated process involving multiple metal deposition steps, thermal annealing, and calcination. Herein, we report the simple preparation of a Janus metallic film by electroless deposition of silver on a poly(dopamine acrylamide) (pDOPAm) thin film. pDOPAm was successfully synthesized via the controlled reversible addition-fragmentation chain transfer polymerization of dopamine acrylamide without a protective group using dimethylformamide as the solvent. The synthesized pDOPAm was spin-coated onto a solid substrate, which was then immersed in an aqueous AgNO3 solution to achieve the electroless deposition of silver. Our preparation method will considerably simplify the fabrication of Janus metallic films, enabling their widespread application as decorative or authentication materials.

Energy Transfer between Size-Controlled CsPbI3 Quantum Dots for Light-Emitting Diode Application.

Perovskite quantum dots (PQDs) are applicable in light-emitting diodes (LEDs) owing to their color tunability, high color purity, and excellent photoluminescence quantum yield (PLQY) in the solution state. However, a PQD film obtained through nonradiative recombination by concentration quenching and the formation of surface defects exhibited a low PLQY. In this study, we focused on the energy transfer between PQDs with different energy gaps (Eg) to reduce nonradiative recombination in the film state and consequently achieve high device performance. We prepared size-controlled PQDs measuring 10.7 nm (large-size QD; LQD) and 7.9 nm (small-size QD; SQD) with different Eg values and observed a spectral overlap between SQD emission and LQD absorption. To investigate the Förster resonance energy transfer (FRET) from SQDs to LQDs, we prepared SQD-LQD mixed QDs (MQDs). The MQD film enhanced LQD emission and exhibited a higher PLQY (52%) with a longer PL decay time (7.4 ns) than those exhibited by the neat LQD film (38% and 6.2 ns). This energy transfer was determined to be FRET by photoluminescence excitation and PL decay times. Moreover, the external quantum efficiency of an MQD-based LED increased to 15%, indicating that the FRET process can enhance the PLQY of the film and LED efficiency.

Gel permeation chromatography process for highly oriented Cs3Cu2I5 nanocrystal film.

The emergence of green materials has attracted considerable attention in the field of optoelectronics. Copper-based lead-free metal halide (with a near-unity quantum yield) obtained from Cs3Cu2I5 nanocrystals (NCs) can exhibit blue emission with a wavelength of 440 nm and provide outstanding stability for various applications. However, in practical applications, colloidal dispersion purity and film quality are inadequate toward a high-performance device. In this study, antisolvent-free gel permeation chromatography is used to purify Cs3Cu2I5 NCs. The purified Cs3Cu2I5 NCs exhibit a high photoluminescent quantum yield and provide a highly oriented single-crystal film. Density functional theory calculation results indicate that the iodide-rich surface in the NCs makes them highly stable. In addition, it has been demonstrated for the first time that the mixture of polymethyl methacrylate (PMMA) and Cs3Cu2I5 NCs has waterproofing capabilities. The composite film consisting of Cs3Cu2I5 NCs and PMMA can survive in water for several days. This result opens up more possibilities for the application of these green material.

Two-Step Crystallization for Low-Oxidation Tin-Based Perovskite Light-Emitting Diodes.

Metal halide perovskites attract significant attention because of their excellent optoelectronic and semiconducting properties. However, there are environmental concerns related to the toxicity of the lead metal that is mainly used in these perovskites. PEA2SnI4 perovskite is a potential candidate for lead-free perovskites because of its pure red emission. Although, undesired Sn4+ oxidation results in the deterioration of PEA2SnI4 perovskite. We demonstrate the two-step crystallization of PEA2SnI4 through the (i) reprecipitation and (ii) recrystallization processes. A film prepared using this method exhibits narrowed emission, with a full width at half-maximum from 30.0 to 26.1 nm, because of its homogeneous emission. Moreover, the Sn4+ content of two-step-crystallized PEA2SnI4 films is five times lower than that of a control film. Diffusion-ordered spectroscopy analysis indicates that the two-step precursor exhibits a smaller hydrodynamic radius crystal seed, which enhances crystallization during spin coating. The resulting two-step crystallized PEA2SnI4-based light-emitting diode (LED) exhibits a maximum external quantum efficiency (EQE) of 0.4% with an average of 0.2%, which is two times greater than that of the control device. This two-step approach may be generalized to synthesize other lead-free materials.

All-Inorganic Quantum-Dot LEDs Based on a Phase-Stabilized α-CsPbI3 Perovskite.

The all-inorganic nature of CsPbI3 perovskites allows to enhance stability in perovskite devices. Research efforts have led to improved stability of the black phase in CsPbI3 films; however, these strategies-including strain and doping-are based on organic-ligand-capped perovskites, which prevent perovskites from forming the close-packed quantum dot (QD) solids necessary to achieve high charge and thermal transport. We developed an inorganic ligand exchange that leads to CsPbI3 QD films with superior phase stability and increased thermal transport. The atomic-ligand-exchanged QD films, once mechanically coupled, exhibit improved phase stability, and we link this to distributing strain across the film. Operando measurements of the temperature of the LEDs indicate that KI-exchanged QD films exhibit increased thermal transport compared to controls that rely on organic ligands. The LEDs exhibit a maximum EQE of 23 % with an electroluminescence emission centered at 640 nm (FWHM: ≈31 nm). These red LEDs provide an operating half-lifetime of 10 h (luminance of 200 cd m-2 ) and an operating stability that is 6× higher than that of control devices.

Neodymium Chloride-Doped Perovskite Nanocrystals for Efficient Blue Light-Emitting Devices.

Metal halides doping of perovskite nanocrystals (NCs) has been shown to precisely control nonradiative pathways and to improve photoluminescence quantum yield (PLQY). Here, we report a trivalent lanthanide halide neodymium (III) chloride (NdCl3)-doped perovskite NCs prepared with a post-synthetic room temperature treatment for efficient blue light-emitting devices (LEDs). The Nd 3d and Cl 2p core peaks were observed in the NdCl3-doped NCs, which allowed for simultaneous doping of Nd3+ and Cl- into the pristine CsPbBr3 NCs. The NdCl3-doped NCs exhibited blue emission at a peak wavelength of 478 nm with a high PLQY of 97% in solution. We found that the Nd3+ cation incorporated into the NCs more effectively suppressed nonradiative recombination compared with common halide anion exchange from temperature dependence of optical properties. Blue LEDs based on NdCl3-doped NCs had an external quantum efficiency of 2.7%, which represents a considerable performance improvement compared with LEDs based on organic chloride salt-doped NCs.

Surface Crystal Growth of Perovskite Nanocrystals via Postsynthetic Lead(II) Bromide Treatment to Increase the Colloidal Stability and Efficiency of Light-Emitting Devices.

The surface modification of metal halide perovskite nanocrystals (NCs) significantly impacts their optical properties and colloidal stability. This subsequently affects the performance of light-emitting devices (LEDs). Therefore, numerous surface passivation techniques like ligand exchange and metal halide doping have been explored to passivate the surface defects of perovskite NCs and obtain highly efficient LEDs. In this study, we demonstrated the postsynthetic metal halide doping treatment using lead(II) bromide (PbBr2) to passivate the surface defects of the CsPbBr3 NCs at a moderate reaction temperature of 80 °C. The alkyl quaternary ammonium salt, didodecyldimethylammonium bromide (DC12AB), enabled the complete dissolution of PbBr2 in a nonpolar solvent, toluene. Because of surface crystal growth, the particle sizes of the PbBr2-doped CsPbBr3 NCs were higher than those of the as-synthesized CsPbBr3 NCs. The photoluminescence quantum yield of the CsPbBr3 NCs drastically increased from 26.8 to 83.9% after the PbBr2 doping treatment. Moreover, the PbBr2-doped CsPbBr3 NCs possessed long-term colloidal stability of more than 2 months that indicates the strong bonding between the NCs and ligands. We observed that the alkyl chain length of the quaternary alkyl ammonium salts affected the luminance and device stability during operations. In this study, a promising strategy was devised to achieve highly luminescent perovskite NCs with excellent colloidal stability that can enhance the performance of LEDs.

Chelating-agent-assisted control of CsPbBr3 quantum well growth enables stable blue perovskite emitters.

Metal halide perovskites have emerged as promising candidates for solution-processed blue light-emitting diodes (LEDs). However, halide phase segregation - and the resultant spectral shift - at LED operating voltages hinders their application. Here we report true-blue LEDs employing quasi-two-dimensional cesium lead bromide with a narrow size distribution of quantum wells, achieved through the incorporation of a chelating additive. Ultrafast transient absorption spectroscopy measurements reveal that the chelating agent helps to control the quantum well thickness distribution. Density functional theory calculations show that the chelating molecule destabilizes the lead species on the quantum well surface and that this in turn suppresses the growth of thicker quantum wells. Treatment with γ-aminobutyric acid passivates electronic traps and enables films to withstand 100 °C for 24 h without changes to their emission spectrum. LEDs incorporating γ-aminobutyric acid-treated perovskites exhibit blue emission with Commission Internationale de l'Éclairage coordinates of (0.12, 0.14) at an external quantum efficiency of 6.3%.

Bipolar-shell resurfacing for blue LEDs based on strongly confined perovskite quantum dots.

Colloidal quantum dot (QD) solids are emerging semiconductors that have been actively explored in fundamental studies of charge transport1 and for applications in optoelectronics2. Forming high-quality QD solids-necessary for device fabrication-requires substitution of the long organic ligands used for synthesis with short ligands that provide increased QD coupling and improved charge transport3. However, in perovskite QDs, the polar solvents used to carry out the ligand exchange decompose the highly ionic perovskites4. Here we report perovskite QD resurfacing to achieve a bipolar shell consisting of an inner anion shell, and an outer shell comprised of cations and polar solvent molecules. The outer shell is electrostatically adsorbed to the negatively charged inner shell. This approach produces strongly confined perovskite QD solids that feature improved carrier mobility (≥0.01 cm2 V-1 s-1) and reduced trap density relative to previously reported low-dimensional perovskites. Blue-emitting QD films exhibit photoluminescence quantum yields exceeding 90%. By exploiting the improved mobility, we have been able to fabricate CsPbBr3 QD-based efficient blue and green light-emitting diodes. Blue devices with reduced trap density have an external quantum efficiency of 12.3%; the green devices achieve an external quantum efficiency of 22%.

Purification of Perovskite Quantum Dots Using Low-Dielectric-Constant Washing Solvent "Diglyme" for Highly Efficient Light-Emitting Devices.

Cesium lead halide (CsPbX3, X = Cl, Br, or I) perovskite quantum dots (QDs) are known as ionic nanocrystals, and their optical properties are greatly affected by the washing solvent used during the purification process. Here, we demonstrate the purification process of CsPbBr3 perovskite QDs using low-dielectric-constant solvents to completely remove impurities, such as the reaction solvent and desorbed ligands. The use of the ether solvent diethylene glycol dimethyl ether (diglyme), having a low dielectric constant of ε = 7.23, as a poor solvent for reprecipitation allowed for multiple wash cycles, which led to high purity and high photoluminescence quantum yield for CsPbBr3 QDs. The light-emitting device constructed with the CsPbBr3 QDs and washed twice with diglyme (two-wash) showed a low turn-on voltage of 2.7 V and a peak external quantum efficiency of over 8%. Thus, the purification of perovskite QDs with multiple wash cycles using a low-dielectric-constant solvent is an effective approach for enhancing not only the optical properties but also the efficiency of perovskite quantum dot light-emitting devices.