Your browser doesn't support javascript.
loading
Mostrar: 20 | 50 | 100
Resultados 1 - 8 de 8
Filtrar
Más filtros










Base de datos
Intervalo de año de publicación
1.
Sensors (Basel) ; 23(13)2023 Jun 25.
Artículo en Inglés | MEDLINE | ID: mdl-37447721

RESUMEN

In this work, a highly miniaturized microstrip antenna array based on two elements is proposed for multiple inputs multiple outputs (MIMO) application systems at sub-6 GHz frequency bands. The antenna is structured from a meander line in conjugate with an interdigital capacitor when excited through the monopole basic antenna. The proposed antenna elements are separated with a Minkowski factor-shaped metamaterial (MTM) column to achieve a separation distance (D) of 0.08λ at 3 GHz when printed on an FR-4 substrate. Later on, the antenna performance in terms of bandwidth and gain is controlled using a photonic process based on optical active switches based on light-dependent resistances (LDR). Therefore, the reconfiguration complexity with such a technique can be eliminated significantly without the need for a biasing circuit. The antenna design was conducted through several parametric studies to arrive at the optimal design that realizes the frequency bandwidth between 3 and 5.5 GHz with a maximum gain of about 4.5 dBi when all LDR terminals are off. For a wireless channel performance study-based massive MIMO environment, the proposed antenna is suitable to be configured in arrays of 64 × 64 elements. From this study, it was found the maximum bit error rate (BER) does not exceed 0.15 with a channel capacity (CC) of 2 Gbps. For validation, the antenna was fabricated based on two elements and tested experimentally. Finally, it was revealed that the measured results agree very well with simulations after comparing the theoretical calculations with the measured data.


Asunto(s)
Fotones , Tecnología
2.
Sensors (Basel) ; 23(11)2023 Jun 02.
Artículo en Inglés | MEDLINE | ID: mdl-37300033

RESUMEN

The permittivity of a material is an important parameter to characterize the degree of polarization of a material and identify components and impurities. This paper presents a non-invasive measurement technique to characterize materials in terms of their permittivity based on a modified metamaterial unit-cell sensor. The sensor consists of a complementary split-ring resonator (C-SRR), but its fringe electric field is contained with a conductive shield to intensify the normal component of the electric field. It is shown that by tightly electromagnetically coupling opposite sides of the unit-cell sensor to the input/output microstrip feedlines, two distinct resonant modes are excited. Perturbation of the fundamental mode is exploited here for determining the permittivity of materials. The sensitivity of the modified metamaterial unit-cell sensor is enhanced four-fold by using it to construct a tri-composite split-ring resonator (TC-SRR). The measured results confirm that the proposed technique provides an accurate and inexpensive solution to determine the permittivity of materials.


Asunto(s)
Electricidad , Refracción Ocular , Conductividad Eléctrica
3.
Micromachines (Basel) ; 14(1)2023 Jan 03.
Artículo en Inglés | MEDLINE | ID: mdl-36677191

RESUMEN

A novel antenna structure is constructed from cascading multi-stage metamaterial (MTM) unit cells-based printed monopole antenna for 5G mobile communication networks. The proposed antenna is constructed from a printed conductive trace that fetches four MTM unit cells through four T-Resonators (TR) structures. Such a combination is introduced to enhance the antenna gain-bandwidth products at sub-6GHz bands after exiting the antenna with a coplanar waveguide (CPW) feed. The antenna circuitry is fabricated by etching a copper layer that is mounted on Taconic RF-43 substrate. Therefore, the proposed antenna occupies an effective area of 51 × 24 mm2. The proposed antenna provides an acceptable matching impedance with S11 ≤ -10 dB at 3.7 GHz, 4.6 GHz, 5.2 GHz, and 5.9 GHz. The antenna radiation patterns are evaluated at the frequency bands of interest with a gain average of 9.1-11.6 dBi. Later, to control the antenna performance, four optical switches based on LDR resistors are applied to control the antenna gain at 5.85 GHz, which is found to vary from 2 dBi to 11.6 dBi after varying the value of the LDR resistance from 700 Ω to 0 Ω, in descending manner. It is found that the proposed antenna provides an acceptable bit error rate (BER) with varying the antenna gain in a very acceptable manner in comparison to the ideal performance. Finally, the proposed antenna is fabricated to be tested experimentally in in free space and in close to the human body for portable applications.

4.
Micromachines (Basel) ; 13(12)2022 Nov 24.
Artículo en Inglés | MEDLINE | ID: mdl-36557360

RESUMEN

A novel design of a reconfigurable MIMO antenna array of a 3D geometry-based solar cell integration that is operating at sub-6 GHz for self-power applications in a 5G modern wireless communication network. The proposed antenna array provides three main frequency bands around 3.6 GHz, 3.9 GHz, and 4.9 GHz, with excellent matching impedance of S11 ≤ -10 dB. The proposed MIMO array is constructed from four antenna elements arranged on a cubical structure to provide a low mutual coupling, below -20 dB, over all frequency bands of interest. Each antenna element is excited with a coplanar waveguide (CPW). The proposed radiation patterns are controlled with two optical switches of Light Dependent Resistors (LDRs). The proposed antenna array is fabricated and tested experimentally in terms of S-parameters, gain and radiation patterns. The maximum gain is found to be 3.6 dBi, 6.9 dBi, and 3.5 dBi at 3.6 GHz, 3.9 GHz, and 4.9 GHz, respectively. It is realized that the proposed array realizes a significant beam forming by splitting the antenna beam and changing the main lobe direction at 3.9 GHz after changing LDR switching statuses. Such an antenna array is found to be very applicable for femtocell wireless communication networks in the 5G systems.

5.
Sensors (Basel) ; 21(23)2021 Nov 26.
Artículo en Inglés | MEDLINE | ID: mdl-34883874

RESUMEN

A microstrip highly sensitive differential sensor for complex permittivity characterization of urine samples was designed, fabricated and tested. The sensing area contains two pairs of open-stub resonators, and the working frequency of the unloaded sensor is 1.25 GHz. The sensor is easily implemented on an affordable substrate FR-4 Epoxy with a thickness of 1.6 mm. A Teflon beaker is mounted on the sensor without affecting the measurements. Numerically, liquid mixtures of water and urine at different percentages were introduced to the proposed sensor to evaluate the frequency variation. The percentage of water content in the mixture varied from 0% (100% urine) to 100% (0% urine) with a step of 3.226%, thus giving 32 data groups of the simulated results. Experimentally, the mixtures of: 0% urine (100% water), 20% urine (80% water), 33% urine (66% water), 50% urine (50% water), 66% urine (33% water), and 100% urine (0% water) were considered for validation. The complex permittivity of the considered samples was evaluated using a nonlinear least square curve fitting in MATLAB in order to realize a sensing sensitivity of about 3%.


Asunto(s)
Microondas , Agua
6.
Sensors (Basel) ; 21(21)2021 Oct 28.
Artículo en Inglés | MEDLINE | ID: mdl-34770453

RESUMEN

This paper presents a microwave sensor based on a two-ports network for liquid characterizations. The proposed sensor is constructed as a miniaturized microwave resonator based on Moore fractal geometry of the 4th iteration. The T-resonator is combined with the proposed structure to increase the sensor quality factor. The proposed sensor occupies an area of 50 × 50 × 1.6 mm3 printed on an FR4 substrate. Analytically, a theoretical study is conducted to explain the proposed sensor operation. The proposed sensor was fabricated and experimentally tested for validation. Later, two pans were printed on the sensor to hold the Sample Under Test (SUT) of crude oil. The frequency resonance of the proposed structure before loading SUT was found to be 0.8 GHz. After printing the pans, a 150 MHz frequency shift was accrued to the first resonance. The sensing part was accomplished by monitoring the S-parameters in terms of S12 regarding the water concentration change in the crude oil samples. Therefore, 10 different samples with different water percentages were introduced to the proposed sensor to be tested for detecting the water content. Finally, the measurements of the proposed process were found to agree very well with their relative simulated results.


Asunto(s)
Microondas , Petróleo , Fractales , Modelos Teóricos , Agua
7.
Sci Rep ; 9(1): 2174, 2019 Feb 18.
Artículo en Inglés | MEDLINE | ID: mdl-30778135

RESUMEN

In this paper, the novelty of exploring the applications of the Iraqi Palm Tree Remnants (IPTR) mixed with Nickel Oxide Nanoparticles (NONP) hosted in Polyethylene (PE), called INP substrates, is utilized by printing metamaterial (MTM) based high gain microwave antennas on them. The proposed INP substrates are mainly created from pressed flexible organic fibers to suite the ink jet printing technologies. The complex relative constitutive parameters are characterized in terms of permittivity (ε) and permeability (µ) within the frequency range from 2 GHz up to 6 GHz using an open end dielectric probe and a T-stub transmission line technique. To validate the feasibility of the INP substrates, a very fine antenna structure of based a miniaturized Hilbert MTM based dipoles is printed on. A material printer with Sliver Nanoparticles Conductive Ink (SNPCI) is used to print the antenna structure. Commercial software packages, CST Microwave Studio (MWS) and Ansys High Frequency Structure Simulator (HFSS), are used to simulate the proposed antenna based on the measured constitutive parameters. A negligible difference is found between the measured and simulated results. Finally, an attractive effect on the retrieved constitutive parameters of the proposed MTM is found due to the proposed INP substrate.

8.
Nanotechnology ; 21(4): 045301, 2010 Jan 29.
Artículo en Inglés | MEDLINE | ID: mdl-20009173

RESUMEN

A novel application that utilizes conductive patches composed of purified multi-walled carbon nanotubes (MWCNTs) embedded in a sodium cholate composite thin film to create microstrip antennas operating in the microwave frequency regime is proposed. The MWCNTs are suspended in an adhesive solvent to form a conductive ink that is printed on flexible polymer substrates. The DC conductivity of the printed patches was measured by the four probe technique and the complex relative permittivity was measured by an Agilent E5071B probe. The commercial software package, CST Microwave Studio (MWS), was used to simulate the proposed antennas based on the measured constitutive parameters. An excellent agreement of less than 0.2% difference in resonant frequency is shown. Simulated and measured results were also compared against identical microstrip antennas that utilize copper conducting patches. The proposed MWCNT-based antennas demonstrate a 5.6% to 2.2% increase in bandwidth, with respect to their corresponding copper-based prototypes, without significant degradation in gain and/or far-field radiation patterns.

SELECCIÓN DE REFERENCIAS
DETALLE DE LA BÚSQUEDA
...