RESUMEN
BACKGROUND: The accurate delineation of ablation zones (AZs) is crucial for assessing radiofrequency ablation (RFA) therapy's efficacy. Manual measurement, the current standard, is subject to variability and potential inaccuracies. AIM: This study aims to assess the effectiveness of Artificial Intelligence (AI) in automating AZ measurements in ultrasound images and compare its accuracy with manual measurements in ultrasound images. METHODS: An in vitro study was conducted using chicken breast and liver samples subjected to bipolar RFA. Ultrasound images were captured every 15 s, with the AI model Mask2Former trained for AZ segmentation. The measurements were compared across all methods, focusing on short-axis (SA) metrics. RESULTS: We performed 308 RFA procedures, generating 7275 ultrasound images across liver and chicken breast tissues. Manual and AI measurement comparisons for ablation zone diameters revealed no significant differences, with correlation coefficients exceeding 0.96 in both tissues (p < 0.001). Bland-Altman plots and a Deming regression analysis demonstrated a very close alignment between AI predictions and manual measurements, with the average difference between the two methods being -0.259 and -0.243 mm, for bovine liver and chicken breast tissue, respectively. CONCLUSION: The study validates the Mask2Former model as a promising tool for automating AZ measurement in RFA research, offering a significant step towards reducing manual measurement variability.
RESUMEN
Breast conserving resection with free margins is the gold standard treatment for early breast cancer recommended by guidelines worldwide. Therefore, reliable discrimination between normal and malignant tissue at the resection margins is essential. In this study, normal and abnormal tissue samples from breast cancer patients were characterized ex vivo by optical emission spectroscopy (OES) based on ionized atoms and molecules generated during electrosurgical treatment. The aim of the study was to determine spectroscopic features which are typical for healthy and neoplastic breast tissue allowing for future real-time tissue differentiation and margin assessment during breast cancer surgery. A total of 972 spectra generated by electrosurgical sparking on normal and abnormal tissue were used for support vector classifier (SVC) training. Specific spectroscopic features were selected for the classification of tissues in the included breast cancer patients. The average classification accuracy for all patients was 96.9%. Normal and abnormal breast tissue could be differentiated with a mean sensitivity of 94.8%, a specificity of 99.0%, a positive predictive value (PPV) of 99.1% and a negative predictive value (NPV) of 96.1%. For 66.6% patients all classifications reached 100%. Based on this convincing data, a future clinical application of OES-based tissue differentiation in breast cancer surgery seems to be feasible.
RESUMEN
Over the last century, there has been a steady development of new technologies for intraoperative tissue identification and differentiation. The applications are varied, with the core purpose being to identify target structures while preserving adjacent tissue and thereby follow a general paradigm of minimally invasive medicine. Particularly in oncology, a further asset of these technologies is the identification or classification of neoplastic tissue to support and improve therapy, for example, in breast cancer surgery.Many technologies under consideration make use of the different physical characteristics of treated tissues, such as induced fluorescence, optical coherence, and electrical impedance.Recent developments are focusing on moving from ex vivo to in situ and from asynchronous to real-time assistance of the clinicians, for example, by means of optical emission spectroscopy. Refinements of existing and the creation of new methods will include AI tools to make them more powerful while reducing the inter-operator variability in operative interventions. This talk addresses several aspects of the usage and suitability of these technologies for intraoperative, therapy-supporting application.
Asunto(s)
Neoplasias de la Mama , Mama , Humanos , Femenino , Mama/cirugía , Neoplasias de la Mama/cirugíaRESUMEN
Endoscopic submucosal dissection (ESD) was developed for the removal of benign and early malignant lesions in the gastrointestinal tract. We aimed to evaluate the performance and safety of a novel high-pressure waterjet-assisted ESD knife in colorectal applications. Six female German Landrace pigs with an average weight of 62 kg (range 60-65 kg) were used in this prospective, randomized, and controlled study. Twenty-four ESDs were performed by three endoscopists: Twelve each with the new Erbe HYBRIDknife® flex T-Type (HK-T) and the Olympus DualKnife® J (DK-J), including six rectal and six colonic ESDs per instrument. The order of performance was randomized regarding anatomic position and instrument. As the primary endpoint, ESD knife performance characteristics were combined and rated on a 5-point Likert scale, with 5 Likert points (LP) representing the best response (5 = very good). The HK-T was rated significantly better than the DK-J (4.7 LP versus 4.4 LP, p = 0.0295), mainly because of HK-T injection ability (5 LP versus 3 LP, p < 0.0001) and hemostasis (5 LP versus 4 LP, p = 0.0452). There was no difference in procedure time (HK-T: 35 min versus DK-J: 34 min, p = 0.8005), resection diameter (3.1 cm versus 2.8 cm, p = 0.3492), injection volume (41 mL versus 46 mL, p = 0.5633), and complication rates. HK-T is as effective as DK-J in colorectal ESD in terms of dissection quality but has better injection and hemostatic properties. The impact of these technical advantages on the ESD treatment of patients with large superficial colorectal lesions remains to be clinically verified.
RESUMEN
INTRODUCTION: A novel multipurpose bipolar radiofrequency instrument, the Erbe Dissector (EDS), which simultaneously seals and cuts tissue, was developed. Ex vivo sealing rate and time, burst pressure, jaw temperature and thermal spread were studied in porcine renal arteries. MATERIAL AND METHODS: In vivo, 13 surgical tasks were performed in two pigs: beside sealing rate and time, overall performance in sharp and blunt dissection, tissue sticking, hemostasis, precision, etc., were evaluated by four surgeons compared with ENSEAL G2 (EG2) using surveys on a Likert scale (1 = very poor; 5 = very good). RESULTS: Ex vivo, the EDS sealing rate was 91.7% (33/36 arteries) at an average sealing time of 2.1 s (range 1.7-2.8) and a burst pressure of 1040 ± 350 mmHg. The maximum jaw temperature was 87 ± 4 °C and the mean lateral thermal spread was 0.8 ± 0.2 mm. In vivo, the sealing rate for arteries and veins was 92.6% (50/54) and the median seal and cut time was 1.6 s (range: 1.3-2.9). The average EDS performance score across all tasks was 4.4 ± 0.6 Likert points. For five shared tasks, EDS was better than EG2 (4.4 ± 0.5 versus 3.4 ± 0.6 Likert points; p = 0.016). CONCLUSIONS: EDS seals and cuts arteries and veins rapidly with good safety and user-friendliness.
Asunto(s)
Hemostasis Quirúrgica , Arteria Renal , Porcinos , Animales , Arteria Renal/cirugía , Venas/cirugía , Ligadura , ElectrocoagulaciónRESUMEN
BACKGROUND: Complete polyp resection is the main goal of endoscopic removal of large colonic polyps. Resection techniques have evolved in recent years and endoscopic submucosal dissection (ESD), endoscopic mucosal resection (EMR) with margin ablation, cold snare polypectomy (CSP), cold EMR, and underwater EMR have been introduced. Yet, efficacy of these techniques with regard to local recurrence rates (LRRs) vs traditional hot snare polypectomy and standard EMR remains unclear. AIM: To analyze LRR of large colonic polyps in a systematic review and meta-analysis. METHODS: MEDLINE, EMBASE, EBM Reviews, and CINAHL were searched for prospective studies reporting LRR or incomplete resection rate (IRR) after colonic polypectomy of polyps ≥ 10 mm, published between January 2011 and July 2021. Primary outcome was LRR for polyps ≥ 10 mm. RESULTS: Six thousand nine hundred and twenty-eight publications were identified, of which 34 prospective studies were included. LRR for polyps ≥ 10 mm at up to 12 mo' follow-up was 11.0% (95%CI, 7.1%-14.8%; 15 studies; 4904 polyps). ESD (1.7%; 95%CI, 0%-3.4%; 3 studies, 221 polyps) and endoscopic mucosal resection with margin ablation (3.3%; 95%CI, 2.2%-4.5%; 2 studies, 947 polyps) significantly reduced LRR vs standard EMR without (15.2%; 95%CI, 12.5%-18.0%; 4 studies, 650 polyps) or with unsystematic margin ablation (16.5%; 95%CI, 15.2%-17.8%; 6 studies, 3031 polyps). CONCLUSION: LRR is significantly lower after ESD or EMR with routine margin ablation; thus, these techniques should be considered standard for endoscopic removal of large colorectal polyps. Other techniques, such as CSP, cold EMR, and underwater EMR require further evaluation in prospective studies before their routine implementation in clinical practice can be recommended.
Asunto(s)
Pólipos del Colon , Neoplasias Colorrectales , Resección Endoscópica de la Mucosa , Pólipos del Colon/cirugía , Colonoscopía/efectos adversos , Colonoscopía/métodos , Neoplasias Colorrectales/cirugía , Resección Endoscópica de la Mucosa/efectos adversos , Resección Endoscópica de la Mucosa/métodos , Humanos , Márgenes de Escisión , Estudios Prospectivos , Resultado del TratamientoRESUMEN
(1) Development of radiofrequency ablation (RFA) systems for pulmonary lesions is restricted by availability of human tumor specimens and limited comparability of animal tissue. We aimed to develop a new surrogate tissue overcoming these drawbacks. (2) Reference values for electrical impedance in lung tumor tissue were collected during routine lung tumor RFA (n = 10). Subsequently, a tissue-mimicking surrogate with comparable electrical impedance and facilitating detection of the ablation margins was developed. (3) The mean electrical impedance for all patients was 103.5 ± 14.7 Ω. In the optimized surrogate tissue model consisting of 68% agar solution, 23% egg yolk, 9% thermochromic ink, and variable amounts of sodium chloride, the mean electrical impedance was adjustable from 74.3 ± 0.4 Ω to 183.2 ± 5.6 Ω and was a function (y = 368.4x + 175.2; R2 = 0.96; p < 0.001) of sodium chloride concentration (between 0 and 0.3%). The surrogate tissue achieved sufficient dimensional stability, and sample cuts revealed clear margins of color change for temperatures higher 60 °C. (4) The tissue-mimicking surrogate can be adapted to lung tumor with respect to its electrical properties. As the surrogate tissue allows for simple and cost-effective manufacturing, it is suitable for extensive laboratory testing of RFA systems for pulmonary ablation.
RESUMEN
Current regimen to treat patients suffering from stress urinary incontinence often seems not to yield satisfactory improvement or may come with severe side effects. To overcome these hurdles, preclinical studies and clinical feasibility studies explored the potential of cell therapies successfully and raised high hopes for better outcome. However, other studies were rather disappointing. We therefore developed a novel cell injection technology to deliver viable cells in the urethral sphincter complex by waterjet instead of using injection needles. We hypothesized that the risk of tissue injury and loss of cells could be reduced by a needle-free injection technology. Muscle-derived cells were obtained from young male piglets and characterized. Upon expansion and fluorescent labeling, cells were injected into cadaveric tissue samples by either waterjet or injection needle. In other experiments, labeled cells were injected by waterjet in the urethra of living pigs and incubated for up to 7 days of follow-up. The analyses documented that the cells injected by waterjet in vitro were viable and proliferated well. Upon injection in live animals, cells appeared undamaged, showed defined cellular somata with distinct nuclei, and contained intact chromosomal DNA. Most importantly, by in vivo waterjet injections, a significantly wider cell distribution was observed when compared with needle injections (P < .05, n ≥ 12 samples). The success rates of waterjet cell application in living animals were significantly higher (≥95%, n = 24) when compared with needle injections, and the injection depth of cells in the urethra could be adapted to the need by adjusting waterjet pressures. We conclude that the novel waterjet technology injects viable muscle cells in tissues at distinct and predetermined depth depending on the injection pressure employed. After waterjet injection, loss of cells by full penetration or injury of the tissue targeted was reduced significantly in comparison with our previous studies employing needle injections.
Asunto(s)
Células Musculares , Agujas , Animales , Humanos , Masculino , Músculos , Porcinos , Tecnología , UretraRESUMEN
OBJECTIVE: The quality of histopathological specimens obtained from the upper urinary tract with conventional flexible ureterorenoscopic biopsy needs to be improved. We investigated the feasibility and biopsy quality of specimens obtained by cryobiopsy, compared with standard ureterorenoscopic biopsy techniques in a human ex vivo model. MATERIALS AND METHODS: Human ureters obtained from nephrectomy specimens (N=12) were dissected and canulated with an ureteral access sheath. Ureterorenoscopic biopsies were randomly obtained from different sites of the renal pelvic caliceal system using different types of instruments. The performance of two newly developed flexible cryoprobes with outer diameters of 1.1 mm (CB11) and 0.9 mm (CB09) was compared with that of the biopsy forceps(FB) and Bigopsy®(BiG) and two different Dormia baskets N-Gage (NG) and Zero-Tip (ZT). We assessed the feasibility of the various biopsy techniques based on the number of biopsy attempts needed to obtain macroscopically discernible biopsies. The specimens were examined histopathologically for size, biopsy quality, presence of various artifact types, and representativeness. RESULTS: Biopsies taken with the cryoprobes showed a higher biopsy quality than biopsies taken with the comparative instruments. The CB11 provided significantly larger biopsies than forceps biopsies and also than biopsies with ZT. The CB09 was able to collect larger samples when compared with the FB and BiG biopsy forceps. There were no significant differences in artifact area, except for the CB11 cryoprobe compared with the NG. To clarify the results a subdivision of larger or smaller than 20% artifact area was performed. A significant difference was found between CB11 and the forceps biopsies, as well as between CB11 and NG and ZT in favor of the cryoprobe. The representation of the histopathological sample was also determined. Biopsies taken with CB11 were more representative compared with forceps biopsies BiG and FB and basket biopsies NG and ZT. CONCLUSIONS: In a standardized comparative ex vivo setting, larger biopsies were obtained by using the cryobiopsy technique with the CB11 probe. Qualitatively, cryobiopsy specimens were overlaid by fewer artifacts and a higher biopsy quality was achieved in histopathologic examination compared with standard instrumentation. Further stepwise development will transfer the promising cryobiopsy technique into the clinical setting.
RESUMEN
OBJECTIVES: Evaluation of smoke capture efficiency of different mobile smoke evacuation devices with respect to volatile organic compounds and their noise emission. METHODS: Electrosurgical incisions were performed on fresh porcine liver in an operating room with vertical laminar flow. The generated surgical smoke was analysed with proton-transfer-reaction mass spectrometry with and without the use of a mobile smoke evacuation system consisting of a smoke evacuator machine, a suction hose and a handpiece. The inlet of the mass spectrometer was positioned 40 cm above the specimen. Various devices were compared: a hard plastic funnel, a flexible foam funnel, an on-tip integrated aspirator of an electrosurgical knife and a standard secretion suction (Yankauer). Also, sound levels were measured at a distance of 40 cm from the handpieces' inlet. RESULTS: The smoke capture efficiency of the secretion suction was only 53%, while foam funnel, plastic funnel and integrated aspirator were all significantly more effective with a clearance of 95%, 91% and 91%, respectively. The mean sound levels were 68 and 59 A-weighted decibels with the plastic and foam funnel, respectively, 66 A-weighted decibels with the integrated aspirator and 63 A-weighted decibels with the secretion suction. CONCLUSIONS: Carcinogenic, mutagenic and reprotoxic volatile organic compounds in surgical smoke can be efficiently reduced by mobile smoke evacuation system, providing improved protection for medical personnel. Devices specifically designed for smoke evacuation are more efficient than standard suction tools. Noise exposure for the surgeon was lowest with the flexible foam funnel and higher with the other handpieces tested.
Asunto(s)
Exposición Profesional , Salud Laboral , Compuestos Orgánicos Volátiles , Animales , Electrocoagulación/métodos , Humanos , Exposición Profesional/efectos adversos , Exposición Profesional/análisis , Exposición Profesional/prevención & control , Quirófanos , Plásticos , Humo/efectos adversos , Humo/análisis , Humo/prevención & control , Porcinos , Compuestos Orgánicos Volátiles/análisisRESUMEN
BACKGROUND: Thermal damage to the muscle layer during mucosal application of argon plasma coagulation (APC) may be avoided by creating a fluid cushion within the submucosal layer, but the minimum injection volume needed or the ideal injection fluid are yet to be established. We conducted a systematic ex vivo study with this aim. METHODS: All experiments were performed in an ex vivo porcine gastrointestinal tract model. Five different fluids (saline, Glyceol, Gelafundin, Voluven, and Eleview) of different volumes were injected into the submucosa of different parts of the gastrointestinal tract. APC was applied to the mucosa at different power settings. Immediately after APC treatment, the temperature was measured through a thermocouple placed inside the fluid cushion, just on top of the muscle layer. The minimum volume of fluid needed to protect the muscle layer from thermal damage was determined. RESULTS: There was no difference in the temperature measured among the different injection fluids at the surface of the muscle, in all the locations, at equal injection volumes and power settings. The minimum amounts of fluid needed to protect the muscle layer were 2 and 3 mL for power settings of 30-90 W and 90-120 W, respectively. CONCLUSIONS: Normal saline and 4 commercially available submucosal injection fluids possess similar thermal protective effects. To reduce the likelihood of thermal damage to deeper layers when APC is applied, a minimum injection volume of 3 mL is recommended if less than 90 W power will be utilized over 3 sec.
RESUMEN
We noted recently that the injection of cells with a needle through a cystoscope in the urethral sphincter muscle of pigs failed to deposit them nearby or at the intended target position in about 50% of all animals investigated (n > 100). Increasing the chance for precise cell injection by shotgun approaches employing several circumferential injections into the sphincter muscle bears the risk of tissue injury. In this study, we developed and tested a novel needle-free technique to precisely inject cells in the urethral sphincter tissue, or other tissues, using a water-jet system. This system was designed to fit in the working channels of endoscopes and cystoscopes, allowing a wide range of minimally invasive applications. We analyze key features, including the physical parameters of the injector design, pressure ranges applicable for tissue penetration and cell injections and biochemical parameters, such as different compositions of injection media. Our results present settings that enable the high viability of cells post-injection. Lastly, the method is suitable to inject cells in the superficial tissue layer and in deeper layers, required when the submucosa or the sphincter muscle of the urethra is targeted.
Asunto(s)
Células/metabolismo , Técnicas Citológicas/métodos , Animales , Supervivencia Celular , Endoscopía , Células HeLa , Humanos , Porcinos , AguaRESUMEN
The reprogramming of patient´s somatic cells into induced pluripotent stem cells (iPSCs) and the consecutive differentiation into cardiomyocytes enables new options for the treatment of infarcted myocardium. In this study, the applicability of a hydrojet-based method to deliver footprint-free iPSC-derived cardiomyocytes into the myocardium was analyzed. A new hydrojet system enabling a rapid and accurate change between high tissue penetration pressures and low cell injection pressures was developed. Iron oxide-coated microparticles were ex vivo injected into porcine hearts to establish the application parameters and the distribution was analyzed using magnetic resonance imaging. The influence of different hydrojet pressure settings on the viability of cardiomyocytes was analyzed. Subsequently, cardiomyocytes were delivered into the porcine myocardium and analyzed by an in vivo imaging system. The delivery of microparticles or cardiomyocytes into porcine myocardium resulted in a widespread three-dimensional distribution. In vitro, 7 days post-injection, only cardiomyocytes applied with a hydrojet pressure setting of E20 (79.57 ± 1.44%) showed a significantly reduced cell viability in comparison to the cells applied with 27G needle (98.35 ± 5.15%). Furthermore, significantly less undesired distribution of the cells via blood vessels was detected compared to 27G needle injection. This study demonstrated the applicability of the hydrojet-based method for the intramyocardial delivery of iPSC-derived cardiomyocytes. The efficient delivery of cardiomyocytes into infarcted myocardium could significantly improve the regeneration.
Asunto(s)
Supervivencia Celular/fisiología , Células Madre Pluripotentes Inducidas/citología , Miocardio/citología , Miocitos Cardíacos/citología , Animales , Diferenciación Celular/fisiología , PorcinosRESUMEN
BACKGROUND: During transurethral resection of bladder tumours (TURB), radio-frequency (RF) currents can lead to adverse neuromuscular stimulation (NMS). Here we present a novel ex vivo method to determine the risk of RF generators and their bipolar TURB modes to cause NMS. We aimed to develop an experimental platform for safety evaluation of new RF generators and their modes with a newly established test standard, suitable for replacement or reduction of animal testing. METHODS: We tested four contemporary RF generators with their bipolar modes for TURB in saline. A two-stage ex vivo approach was pursued: First, we recorded voltages at possible positions of the obturator nerve behind a porcine bladder wall in a TURB model using 18 RF applications per generator. Second, these voltage records were used as stimuli to evoke nerve compound action potentials (CAPs) in isolated porcine axillary nerves. The NMS potential was defined as the ratio between the observed area under the CAPs and the theoretical CAP area at maximum response and a firing rate of 250 Hz, which would reliably induce tetanic muscle responses in most human subjects. The measurement protocol was tailored to optimise reproducibility of the obtained NMS potentials and longevity of the nerve specimens. RESULTS: As prerequisite for the clinical translation of our results, the robustness of our test method and reproducibility of the NMS potential are demonstrated with an excellent correlation (r = 0.93) between two sets of identical stimuli (n = 72 each) obtained from 16 nerve segments with similar diameters (4.2 ± 0.37 mm) in the nerve model. The RF generators differed significantly (p < 0.0001) regarding NMS potential (medians: 0-3%). CONCLUSIONS: Our test method is suitable for quantifying the NMS potential of different electrosurgical systems ex vivo with high selectivity at a reasonable degree of standardization and with justifiable effort. Our results suggest that the clinical incidence of NMS is considerably influenced by the type of RF generator. Future generations of RF generators take advantage from the proposed test standard through higher safety and less animal testing. Health professionals and treated patients will benefit most from improved RF surgery using generators with a low NMS risk.
Asunto(s)
Próstata/cirugía , Ablación por Radiofrecuencia/efectos adversos , Ablación por Radiofrecuencia/instrumentación , Vejiga Urinaria/cirugía , Animales , Cistectomía/métodos , Estimulación Eléctrica , Masculino , Músculo Liso , Unión Neuromuscular , Próstata/inervación , Prostatectomía/métodos , Ablación por Radiofrecuencia/métodos , Medición de Riesgo , Porcinos , Uretra , Vejiga Urinaria/inervaciónRESUMEN
BACKGROUND: Electrosurgical vessel sealers are gradually replacing conventional techniques such as ligation and clipping. Algorithms that control electrosurgical units (ESU), known as modes, are important for applications in different surgical disciplines. This chronic porcine animal study aimed to evaluate the safety and effectiveness of the novel thermoSEAL electrosurgical vessel sealing mode (TSM). The BiClamp® mode (BCM) of the renowned VIO® 300 D ESU served as control. BCM has been widely available since 2002 and has since been successfully used in many surgical disciplines. The TSM, for the novel VIO® 3 ESU, was developed to reduce sealing time and/or thermal lateral spread adjacent to the seal while maintaining clinical success rates. The primary aim of this study was to investigate the long-term and intraoperative seal quality of TSM. METHODS: The BiCision® device was used for vessel sealing with TSM and BCM in ten German Landrace pigs which underwent splenectomy and unilateral nephrectomy during the first intervention of the study. The seals were cut with the BiCision® knife. Ninety-nine arteries, veins and vascular bundles were chronically sealed for 5 or 21 days. Thereafter, during the second and terminal intervention of the study, 97 additional arteries and veins were sealed. The carotid arteries were used for histological evaluation of thermal spread. RESULTS: After each survival period, no long-term complications occurred with either mode. The intraoperative seal failure rates, i.e. vessel leaking or residual blood flow after the first sealing activation, were 2% with TSM versus 6% with BCM (p = 0.28). The sealing time was significantly shorter with TSM (3.5 ± 0.69 s vs. 7.3 ± 1.3 s, p < 0.0001). The thermal spread and burst pressure of arteries sealed with both modes were similar (p = 0.18 and p = 0.61) and corresponded to the histological evaluation. The measured tissue sticking parameter was rare with both modes (p = 0.33). Tissue charring did not occur. Regarding the cut quality, 97% of the seals were severed in the first and 3% in the second attempt (both with TSM and BCM). CONCLUSIONS: The novel TSM seals blood vessels twice as fast as the BCM while maintaining excellent tissue effect and clinical success rates. TRIAL REGISTRATION: Not applicable.
Asunto(s)
Algoritmos , Electrocirugia , Nefrectomía , Esplenectomía , Animales , Femenino , Arterias/cirugía , Electrocoagulación , Electrocirugia/métodos , Ligadura , Nefrectomía/métodos , Esplenectomía/métodos , Porcinos , Venas , Distribución AleatoriaRESUMEN
OBJECTIVE: To develop a novel device for cryobiopsy of the upper urinary tract (UUT) and to evaluate its feasibility in a standardized preclinical setting. MATERIALS AND METHODS: Flexible cryoprobes (diameter 0.9 mm; cooling agent CO2) were developed and used to extract biopsies in porcine UUTs. Cryosamples obtained by ureterorenoscopy were systematically compared with biopsy specimens obtained with standard of care devices in terms of physical characteristics (deflection angle and irrigation flow rates) and histologic criteria (assessability). RESULTS: Irrigation flow rates were significantly higher with introduced BIGopsy (2.8 ± 0.1) compared with standard forceps (0.94 ± 0.06; P < .001) and cryoprobe (1.1 ± 0.1; P < .001). Angular deflection was significantly reduced by the inserted cryoprobe (130.7° ± 1.2° vs 166.9° ± 1.1° [BIGopsy] or 161.4° ± 1.9° [standard forceps]; both P < .001). Significantly larger UUT tissue samples were obtained by the cryoprobe (mean specimen area 7.5 ± 2.5 vs 4.6 ± 2.5 mm² [BIGopsy] or 1.4 ± 1.4 mm² [standard forceps]; both P < .001). No crush artifacts were observed in cryosamples. Superior histologic assessability scores were achieved in samples obtained by the cryoprobe (mean 2.8 ± 0.8) and BIGopsy (2.3 ± 1.9) when compared with standard forceps (0.4 ± 0.9; P < .001). CONCLUSION: Cryobiopsy in the UUT is feasible and represents a viable new option to improve the diagnostic accuracy of histopathologic evaluation. Larger and more representative tissue samples can be obtained using a cryoprobe and artifacts may be avoided. Further optimization of the probe will reduce possible restrictions of ureterorenoscopy handling when the device is inserted.
Asunto(s)
Riñón/patología , Uréter/patología , Animales , Biopsia/instrumentación , Biopsia/métodos , Criocirugía , Diseño de Equipo , Estudios de Factibilidad , PorcinosRESUMEN
BACKGROUND: Bipolar vessel sealing has been successfully introduced in a variety of procedures like prostatectomy, hysterectomy, and nephrectomy. In this study, we evaluated a new sealing mode-the thermoSEAL® mode (TSM)-operated with the VIO3 generator in an ex vivo and in vivo animal study and compared the results with the commercially available BiClamp mode (BCM), operated with the VIO300D generator. Two different instruments were used in combination with both modes, BiCision® and BiClamp® 201T (Erbe Elektromedizin GmbH). METHODS: In the ex vivo experiment, the sealing of renal arteries was evaluated using both instruments and modes. For the in vivo study, different types of arteries and veins were sealed using both modes and instruments in a side-by-side comparison for acute complications in a total of four animals. RESULTS: Mean burst pressure was in all cases significantly above 360 mmHg (p < 0.001). Sealing time during the ex vivo setting was significantly shorter for TSM compared to BCM: BiCision® (3.7 ± 0.4 vs. 7.1 ± 0.3 s; p < 0.0001); BiClamp® 201T (3.9 ± 0.3 vs. 5.1 ± 1.1 s; p < 0.0015). Lateral thermal damage was more pronounced for BCM: BiCision® (TSM 1.4 ± 0.3 mm vs. BCM 1.9 ± 0.2 mm; p < 0.0001); BiClamp® 201T (TSM 1.9 ± 0.6 mm vs. BCM 3.1 ± 0.6 mm; p < 0.0001). The sealing time during the in vivo study was significantly shorter for TSM in combination with BiCision® for arteries [TSM 3.0 ± 0.7 s vs. BCM 6.5 ± 1.3 s, (p < 0.0001) and veins 3.2 ± 1.1 vs. 5.8 ± 1.8 s, (p < 0.0001)]. No significant differences were seen for the two modes used with BiClamp® 201T [artery: TSM 3.3 ± 0.7 s vs. BCM 3.4 ± 0.9 s, (p = 0.891)]. High sealing rates for arteries (100%) and veins (>90%) were noted for both instruments and modes. CONCLUSIONS: While both modes used with two different instruments reveal high safety characterized by a high burst pressure, low thermal damage (ex vivo) zones, and high sealing rates (in vivo), the thermoSEAL® mode convinces by its fast sealing speed probably helping to reduce operation time.
Asunto(s)
Arterias Carótidas/cirugía , Electrocirugia/instrumentación , Hemostasis Quirúrgica/instrumentación , Arteria Renal/cirugía , Venas/cirugía , Animales , Electrocirugia/efectos adversos , Electrocirugia/métodos , Hemostasis Quirúrgica/efectos adversos , Hemostasis Quirúrgica/métodos , Técnicas In Vitro , Modelos Animales , Tempo Operativo , Estudios Prospectivos , Distribución Aleatoria , PorcinosRESUMEN
BACKGROUND: Thermal ablation for Barrett's oesophagus has widely been established in gastrointestinal endoscopy during the last decade. The mainly used methods of radiofrequency ablation (RFA) and argon-plasma coagulation (APC) carry a relevant risk of stricture formation of up to 5-15%. Newer ablation techniques that are able to overcome this disadvantage would therefore be desirable. The aim of the present study was to compare the depth of tissue injury of the new method of Hybrid-APC versus standard APC within a randomized study in a porcine oesophagus model. METHODS: Using a total of eight explanted pig oesophagi, 48 oesophageal areas were ablated either by standard or Hybrid-APC (APC with prior submucosal fluid injection) using power settings of 50 and 70 W. The depth of tissue injury to the oesophageal wall was analysed macroscopically and histopathologically. RESULTS: Using 50 W, mean coagulation depth was 937 ± 469 µm during standard APC, and 477 ± 271 µm during Hybrid-APC (p = 0.064). Using 70 W, coagulation depth was 1096 ± 320 µm (standard APC) and 468 ± 136 µm (Hybrid-APC; p = 0.003). During all settings, damage to the muscularis mucosae was observed. Using standard APC, damage to the submucosal layer was observed in 4/6 (50 W) and 6/6 cases (70 W). During Hybrid-APC, coagulation of the submucosal layer occurred in 2/6 (50 W) and 1/6 cases (70 W). The proper muscle layer was only damaged during conventional APC (50 W: 1/6; 70 W: 3/6). LIMITATIONS: Ex-vivo animal study with limited number of cases. CONCLUSIONS: Hybrid-APC reduces coagulation depth by half in comparison with standard APC, with no thermal injury to the proper muscle layer. It may therefore lead to a lower rate of stricture formation during clinical application.
RESUMEN
PURPOSE: The aim of this study is to systematically investigate under standardized experimental conditions the effects of instrument contamination and wear on the quality of bipolar vessel sealing (BVS) achieved using a reusable instrument. METHODS: The study was designed as a prospective, randomized, and controlled in vitro study and conducted in an academic research environment. Reusable bipolar coagulation forceps (BiClamp® 200 C, ERBE Elektromedizin) were used to apply sealing pressures of 300-1,100 mN/mm(2) to 239 renal arteries from commercially slaughtered female pigs (Swabian-Hall Swine). Forceps jaws were coated with porcine blood, blood and collagen, or blood, collagen, and fat to simulate instrument contamination with biological material during surgery. Clinical wear was mimicked by sandpaper abrasion. The main outcome measures were seal success (resistance to 250 mmHg intraluminal pressure for 2 min) and seal stability (burst pressure). RESULTS: Sealing pressure had a significant impact, with 800 mN/mm(2) producing the best sealing results. Seal success increased with total energy applied to the tissue, a higher maximum temperature, and longer coagulation as indicated by desiccation time. Experimental contamination had no significant impact on seal success and only a limited effect on seal stability. Similarly, abrasive wear also had no significant effect on either seal quality or seal strength. CONCLUSIONS: The impact of bipolar forceps contamination and wear on seal success and quality was negligible in our in vitro model. To achieve high-quality seals, it is essential to use adequate sealing pressures. Our findings could have direct implications for the design and clinical handling of BVS instruments.
Asunto(s)
Electrocoagulación/instrumentación , Contaminación de Equipos , Arteria Renal/cirugía , Animales , Equipo Reutilizado , Femenino , Ligadura/instrumentación , Presión , Estudios Prospectivos , Instrumentos Quirúrgicos , Porcinos , Procedimientos Quirúrgicos Vasculares/instrumentaciónRESUMEN
RATIONALE AND OBJECTIVES: To evaluate the ex vivo ablation zones created in hepatic tissue using monopolar and bipolar gas- and water-cooled radiofrequency (RF) applicators. MATERIALS AND METHODS: RF ablations were performed on ex vivo bovine liver tissue using closed circuit water-cooled and closed circuit cryogenically cooled (via CO2 enthalpy) 15-ga linear-needle applicators. Both monopolar and bipolar electrode applicators were used, with the electric current administered ranging in 50-mA increments from 1100 to 1300 mA for the monopolar case, and from 500 to 700 mA for the bipolar case. Total ablation time was 15 minutes. Six tissue samples were ablated per setting. The ablated volumes were assumed to have a three-dimensional ellipsoid shape, with one long major axis and two smaller minor axes. Gross histology was used to measure the dimensions of the ablated regions to quantify the ablated volume, the dimensions of the axis, and the ratio between the long axis and the smallest minor axis, which was termed the ellipticity index. RESULTS: The gas-cooled monopolar applicator achieved the largest short-axis ablation diameter (4.05 ± 0.4 cm), followed by the water-cooled monopolar applicator (3.18 ± 0.29 cm). With the bipolar applicator, the gas-cooled applicators also achieved larger short-axis ablation diameters (3.02 ± 0.15 cm) than the water-cooled applicators (2.72 ± 0.29 cm). The gas-cooled monopolar applicator also provided the largest ablation volume (42.7 ± 10.7 mL) and the most spherically shaped lesions (ellipticity index: 1.21 ± 0.10). Lesion size increased with injected current up to a threshold current of 1200/1250 mA (monopolar water-/gas-cooled) and 600/650 mA (bipolar water-/gas-cooled), but dropped at greater values. CONCLUSIONS: Gas-cooled monopolar applicators were superior to the other tested applicators in terms of both volume and sphericity of the ablation zone.