Sticky Multicolor Mechanochromic Labels.

Sticky-colored labels are an efficient way to communicate visual information. However, most labels are static. Here, we propose a new category of dynamic sticky labels that change structural colors when stretched. The sticky mechanochromic labels can be pasted on flexible surfaces such as fabric and rubber or even on brittle materials. To enhance their applicability, we demonstrate a simple method for imprinting structural color patterns that are either always visible or reversibly revealed or concealed upon mechanical deformation. The mechanochromic patterns are imprinted with a photomask during the ultraviolet (UV) cross-linking of acrylate-terminated cholesteric liquid crystal oligomers in a single step at room temperature. The photomask locally controls the cross-linking degree and volumetric response of the cholesteric liquid crystal elastomers (CLCEs). A nonuniform thickness change induced by the Poisson's ratio contrast between the pattern and the surrounding background might lead to a color-separation effect. Our sticky multicolor mechanochromic labels may be utilized in stress-strain sensing, building environments, smart clothing, security labels, and decoration.

NIR-vis-UV Light-Responsive High Stress-Generating Polymer Actuators with a Reduced Creep Rate.

Untethered, light-responsive, high-stress-generating actuators based on widely-used commercial polymers are appealing for applications in soft robotics. However, the construction of actuators that are stable and reversibly responsive to low-intensity ultraviolet, visible, and infrared lights remains challenging. Here, transparent, stress-generating actuators are reported based on ultradrawn, ultrahigh molecular weight polyethylene films. The composite films have different draw ratios (30, 70, and 100) and contain a small amount of graphene in combination with ultraviolet and near-infrared-absorbing dyes. The composite actuators respond rapidly (t0.9 < 0.8 s) to different wavelengths of light (i.e., 780, 455, and 365 nm). A maximum photoinduced stress of 35 MPa is achieved at a draw ratio of 70 under near-infrared light irradiation. The photoinduced stress increases linearly with the light intensity, indicating the transfer of light into thermally induced mechanical contraction. Moreover, the addition of additives lead to a reduction in the plastic creep rate of the drawn films compared to their nonmodified counterparts.

Unravelling humidity-gated, temperature responsive bilayer actuators.

By spraying liquid crystal mixtures onto stretched polyamide 6 (PA6) substrates, dual-responsive heat/humidity bilayer actuators are generated. The oriented PA6 guides the self-organization of the liquid crystal monomers into well-aligned, anisotropic liquid crystal networks. The bilayer responds to changes in the environmental relative humidity, resulting in bending of the actuator with the liquid crystal network inside the curvature. In contrast, in conditions of constant high humidity (80%RH), increasing the temperature triggers the liquid crystal network coating to bend the bilayer in the opposing direction. The dual-responsivity to changes in environmental humidity and temperature is examined in detail and discussed theoretically to elucidate the humidity-gated, temperature responsive properties revealing guidelines for fabricating anisotropic bilayer actuators.

Liquid Crystal Networks on Thermoplastics: Reprogrammable Photo-Responsive Actuators.

Arbitrary shape (re)programming is appealing for fabricating untethered shape-morphing photo-actuators with intricate configurations and features. We present re-programmable light-responsive thermoplastic actuators with arbitrary initial shapes through spray-coating of polyethylene terephthalate (PET) with an azobenzene-doped light-responsive liquid crystal network (LCN). The initial geometry of the actuator is controlled by thermally shaping and fixing the thermoplastic PET, allowing arbitrary shapes, including origami-like folds and left- and right-handed helicity within a single sample. The thermally fixed geometries can be reversibly actuated through light exposure, with fast, reversible area-specific actuation such as winding, unwinding and unfolding. By shape re-programming, the same sample can be re-designed and light-actuated again. The strategy presented here demonstrates easy fabrication of mechanically robust, recyclable, photo-responsive actuators with highly tuneable geometries and actuation modes.

Photonic Shape Memory Polymer with Stable Multiple Colors.

A photonic shape memory polymer film that shows large color response (∼155 nm) in a wide temperature range has been fabricated from a semi-interpenetrating network of a cholesteric polymer and poly(benzyl acrylate). The large color response is achieved by mechanical embossing of the photonic film above its broad glass transition temperature. The embossed film, as it recovers to its original shape on heating through the broad thermal transition, exhibits multiple structural colors ranging from blue to orange. The relaxation behavior of the embossed film can be fully described using a Kelvin-Voigt model, which reveals that the influence of temperature on the generation of colors is much stronger than that of time, thereby producing stable multiple colors.

Time-dependent failure of amorphous poly-D,L-lactide: influence of molecular weight.

The specific time-dependent deformation response of amorphous poly(lactic acid) (PLA) is known to lead to rapid failure of these materials in load-bearing situations. We have investigated this phenomenon in uniaxial compression on P(L)DLLA samples with various molecular weights. The experiments revealed a strong dependence of the yield stress on the applied strain rate. Lower molecular weights showed identical deformation kinetics as higher molecular weights, albeit at lower stress values. This dependence on molecular weight was incorporated into an Eyring-equation by introducing mobility through a virtual temperature that is shifted by the deviation of the T(g) from T(g,∞). Stress-dependent lifetime of polymer constructs was described by the use of this modified Eyring-equation, combined with a critical plastic strain. This model proves useful in predicting the molecular weight dependence of the time to failure, although it slightly overestimates life time at low stress levels for a material with very low molecular weight. The versatility of the model is demonstrated on e-beam sterilized PLDLLA, where the resulting reduction in molecular weight induces a substantial decrease in lifetime. A single T(g) measurement provides sufficient information to predict the decrease in lifetime.

Time-dependent failure of amorphous polylactides in static loading conditions.

Polylactides are commonly praised for their excellent mechanical properties (e.g. a high modulus and yield strength). In combination with their bioresorbability and biocompatibility, they are considered prime candidates for application in load-bearing biomedical implants. Unfortunately, however, their long-term performance under static load is far from impressive. In a previous in vivo study on degradable polylactide spinal cages in a goat model it was observed that, although short-term mechanical and real-time degradation experiments predicted otherwise, the implants failed prematurely under the specified loads. In this study we demonstrate that this premature failure is attributed to the time-dependent character of the material used. The phenomenon is common to all polymers, and finds its origin in stress-activated segmental molecular mobility leading to a steady rate of plastic flow. The stress-dependence of this flow-rate is well captured by Eyring's theory of absolute rates, as demonstrated on three amorphous polylactides of different stereoregularity.We show that the kinetics of the three materials are comparable and can be well described using the proposed modeling framework. The main conclusion is that knowledge of the instantaneous strength of a polymeric material is insufficient to predict its long-term performance.

Time-dependent mechanical strength of 70/30 Poly(L, DL-lactide): shedding light on the premature failure of degradable spinal cages.

STUDY DESIGN: In vitro studies on the mechanical strength of 70/30 poly(l,dl-lactic acid) (70/30 PLDLLA) cages. OBJECTIVE: To evaluate the effect of loading rate, humidity, temperature, and continuous static loading on the strength of 70/30 PLDLLA, to elucidate the mechanism of premature failure of degradable spinal cages observed in earlier studies. SUMMARY OF BACKGROUND DATA: Degradable 70/30 PLDLLA cages have been designed to withstand mechanical loads in a goat lumbar spine for at least 6 months. Yet mechanical failure was observed after only 3 months in vivo. We hypothesize that this observation can be related to the time-dependent nature of the polymer. METHODS: Degradable 70/30 PLDLLA cages were loaded to failure at loading rates between 10 and 10 mm/s under standard loading conditions (in air at room temperature: +/-23 degrees C). The experiments were also done at body temperature (37 degrees C) and under wet conditions. Furthermore, we determined the time-to-failure for 70/30 PLDLLA cages subjected to loads well below their instantaneous mechanical strength. RESULTS: The mechanical strength of 70/30 PLDLLA cages was lower for lower loading rates, higher temperature, and higher humidity. The cages already failed within less than 5 minutes when statically loaded at 75% of their strength, and within 1 day when loaded at about 50% of their strength. Extrapolation predicts cage failure at 3 months when loaded at 25% of their strength. CONCLUSION: Premature failure of 70/30 PLDLLA cages, as observed in vivo in earlier studies, is owing to mechanical loading and the time-dependent mechanical properties of the material. The standards for mechanical testing of implants made of strongly time-dependent materials like polylactide should be reconsidered.