RESUMEN
Donor-acceptor (D-A) copolymers containing perylene-3,4,9,10-tetracarboxydiimide (PDI) electron-acceptor (A) units belonging to n-type semiconductors are of interest due to their many potential applications in photonics, particularly for electron-transporting layers in all-polymeric or perovskite solar cells. Combining D-A copolymers and silver nanoparticles (Ag-NPs) can further improve material properties and device performances. Hybrid layers of D-A copolymers containing PDI units and different electron-donor (D) units (9-(2-ethylhexyl)carbazole or 9,9-dioctylfluorene) with Ag-NPs were prepared electrochemically during the reduction of pristine copolymer layers. The formation of hybrid layers with Ag-NP coverage was monitored by in-situ measurement of absorption spectra. The Ag-NP coverage of up to 41% was higher in hybrid layers made of copolymer with 9-(2-ethylhexyl)carbazole D units than in those made of copolymer with 9,9-dioctylfluorene D units. The pristine and hybrid copolymer layers were characterized by scanning electron microscopy and X-ray photoelectron spectroscopy, which proved the formation of hybrid layers with stable Ag-NPs in the metallic state with average diameters <70 nm. The influence of D units on Ag-NP diameters and coverage was revealed.
RESUMEN
Thin films made of formamidinium lead iodide (FAPbI3) perovskites prepared by a two-step sequential deposition method using various solvents for formamidinium iodide (FAI) - isopropanol, n-butanol and tert-butanol, were studied with the aim of finding a correlation between morphology and solvent properties to improve film quality. They were characterized by X-ray diffraction (XRD) and scanning electron microscopy (SEM) and their photophysical properties were studied by means of absorption and photoluminescence (PL) spectroscopies. XRD patterns, absorption and PL spectra proved α-phase formation for all selected solvents. An excessive amount of PbI2 found in perovskite films prepared with n-butanol indicates incomplete conversion. Thin film morphology, such as grain and crystallite size, depended on the solvent. Using tert-butanol, thin films with a very large grain size of up to several micrometers and with preferred crystallite orientation were fabricated. The grain size increased as follows: 0.2-0.5, 0.2-1 and 2-5 µm for isopropanol, n-butanol and tert-butanol, respectively. A correlation between the grain size and viscosity, electric permittivity and polarizability of the solvent could be considered. Our results, including fabrication of perovskite films with large grains and fewer grain boundaries, are important and of interest for many optoelectronic applications.
RESUMEN
Physical entities with inherent randomness have been investigated as anti-counterfeiting labels based on physical unclonable functions (PUFs). Herein, a transparent and flexible optical PUF label associated with multilevel complexity is demonstrated by taking advantage of the optical properties of hierarchical morphologies of the composite film composed of metal halide perovskite nanoparticles (MAPbBr3 NPs) and the intrinsic spinodal-decomposition-like phase separation of polymer blend (PMMA/PS blend). Due to the combinatorial effects of the photolysis synthesis of MAPbBr3 and the thermodynamic instability of the PMMA/PS blend, randomized patterns emerge at two-level scales. These patterns are intrinsically non-deterministic, and therefore, the PUF labels from the multilevel random patterns are challenging to replicate. This is mainly attributed to random spot patterns (higher-level patterns) confined within intricate bicontinuous patterns (lower-level patterns).
RESUMEN
Hybrid layers of donor-acceptor (D-A) copolymers containing N,N'-dialkylperylene-3,4,9,10-tetracarboxydiimide electron-acceptor units covered with silver nanoparticles (Ag-NPs) were prepared by electrochemical doping of pristine layers during reduction processes. In situ optical absorption spectra of the layers were recorded during the formation of Ag-NP coverage. The hybrid layers were characterized by absorption spectroscopy, scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS), and energy dispersive X-ray spectroscopy (EDX). In the absorption spectra of the hybrid layers, a surface plasmon band characteristic of Ag-NPs appeared. Significant improvements in light absorption due to the plasmonic effects of Ag NPs were observed. Stable Ag-NPs with an average diameter of 41-63 nm were formed on the surface, as proven by SEM and XPS. The Ag-NP coverage and size depended on the hybrid layer preparation conditions and on the copolymer composition. The metallic character of the Ag-NPs was proven by XPS. The location in the surface layer was further confirmed by EDX analysis. To the best of our knowledge, this is the first report on such hybrid layers having the potential for a variety of photonic and electronic applications.
RESUMEN
Herein, we report a solid-state lithography technique utilizing eutectic friction transfer lithography (EFTL). The EFTL technique employs eutectic pellets made of semiconducting polymers and volatile organic solid matrices. Using frictional heating and eutectic melting, various semiconducting polymer crystals were formed by a simple rubbing process under mild conditions. The strong anisotropic optical properties suggest that J-type packing is dominant in EFTL microwires because of the highly extended and planarized crystal structures.
RESUMEN
Halide vacancy defect is one of the major origins of non-radiative recombination in the lead halide perovskite light emitting devices (LEDs). Hence the defect passivation is highly demanded for the high-performance perovskite LEDs. Here, we demonstrated that FA doping led to the enrichment of Br in Cs1-xFAxPbBr3 QDs. Due to the defect passivation by the enriched Br, the trap density in Cs1-xFAxPbBr3 significantly decreased after FA doping, and which improved the optical properties of Cs1-xFAxPbBr3 QDs and their QD-LEDs. PLQY of Cs1-xFAxPbBr3 QDs increased from 76.8% (x = 0) to 85.1% (x = 0.04), and Lmax and CEmax of Cs1-xFAxPbBr3 QD-LEDs were improved from Lmax = 2880 cd m-2 and CEmax = 1.98 cd A-1 (x = 0) to Lmax = 5200 cd m-2 and CEmax = 3.87 cd A-1 (x = 0.04). Cs1-xFAxPbBr3 QD-LED device structure was optimized by using PVK as a HTL and ZnO modified with b-PEI as an ETL. The energy band diagram of Cs1-xFAxPbBr3 QD-LEDs deduced by UPS analyses.
RESUMEN
Perovskite nanoparticle composite films with capability of high-resolution patterning (≥2 µm) and excellent resistance to various aqueous and organic solvents are prepared by in situ photosynthesis of acrylate polymers and formamidinium lead halide (FAPbX3 ) nanoparticles. Both positive- and negative-tone patterns of FAPbX3 nanoparticles are created by controlling the size exclusive flow of nanoparticles in polymer networks. The position of nanoparticles is spatially controlled in both lateral and vertical directions. The composite films show high photoluminescence quantum yield (up to 44%) and broad color tunability in visible region (λpeak = 465-630 nm).