Influence of the microstructure on electrochemical corrosion and nickel release in NiTi orthodontic archwires.

The aim of this work was to determine the influence of the present phases and the chemical composition on the corrosion behavior and the nickel ion release of the NiTi orthodontic archwires. Eight Ni-Ti archwires from six commercial brands, in the as-received condition, were studied. The chemical composition, roughness, microstructure and the proportion of the phases as well as the corrosion behavior were analyzed for each archwire. The nickel ion release was characterized in artificial saliva immersion settings ranging up to 4 weeks. The results show that the presence of the martensitic phase improves corrosion resistance and significantly decreases Ni release into exterior medium in comparison with the austenitic specimens. In spite of the partial loss of superelasticity produced in the martensitic phase, it could be of great interest for biomedical applications, as it could minimize sensitization and allergies and improve biocompatibility and corrosion resistance of NiTi shape memory alloys.

New Ni-free superelastic alloy for orthodontic applications.

A potential new Ni-free Ti alloy for biomedical applications was assessed in order to investigate the superelastic behavior, corrosion resistance and the biocompatibility. The alloy studied was Ti19.1Nb8.8Zr. The chemical composition was determined by X-ray microanalysis, the thermoelastic martensitic transformation was characterized by high sensitivity calorimeter. The critical stresses were determined by electromechanical testing machine and the corrosion behavior was analyzed by potentiostatic equipment in artificial saliva immersion at 37°C. The results were compared with six different NiTi orthodontic archwire brands. The biocompatibility was studied by means of cultures of MG63 cells. Ni-free Ti alloy exhibits thermoelastic martensitic transformation with Ms=45°C. The phase present at 37°C was austenite which under stress can induce martensite. The stress-strain curves show a superelastic effect with physiological critical stress (low and continuous) and a minimal lost of the recovery around 150 mechanical cycles. The corrosion resistance improves the values obtained by different NiTi alloys avoiding the problem of the Ni adverse reactions caused by Ni ion release. Cell culture results showed that adhered cell number in new substrate was comparable to that obtained in a commercially pure Ti grade II or beta-titanium alloy evaluated in the same conditions. Consequently, the new alloy presents an excellent in-vitro response.

Friction coefficients and wear rates of different orthodontic archwires in artificial saliva.

The aim of this paper is to analyze the influence of the nature of the orthodontic archwires on the friction coefficient and wear rate against materials used commonly as brackets (Ti-6Al-4V and 316L Stainless Steel). The materials selected as orthodontic archwires were ASI304 stainless steel, NiTi, Ti, TiMo and NiTiCu. The array archwire's materials selected presented very similar roughness but different hardness. Materials were chosen from lower and higher hardness degrees than that of the brackets. Wear tests were carried out at in artificial saliva at 37 °C. Results show a linear relationship between the hardness of the materials and the friction coefficients. The material that showed lower wear rate was the ASI304 stainless steel. To prevent wear, the wire and the brackets have high hardness values and in the same order of magnitude.

Corrosion and corrosion-fatigue behavior of cp-Ti and Ti-6Al-4V laser-marked biomaterials.

The aim of this work was to determine the influence of laser surface modification treatments on mechanical and electrochemical behavior in Ti and Ti-6Al-4V implants. For each metal, different samples were laser modified simulating the markings according to the international requirements. (It is necessary in each metallic biomaterial to mark the serial, batch and company numbers.) Microstructural changes produced by this treatment were observed: (a) the melting zone with small grain sizes and martensitic structures in above-mentioned metals and (b) the heat-affected zone (HAZ) with alpha phase in cp-Titanium with bigger grain sizes and Widmanstatten structure in Ti-6Al-4V. Positive tensile residual stress was determined by means X-ray analysis in the zones marked by laser. Furthermore, corrosion behavior was studied in a simulated body fluid at 37°C. Pitting was observed in different zones near the HAZ and the results showed a decrease of the corrosion resistance in the laser treated samples. Residual stresses and the martensitic microstructures favoured the decrease of the corrosion-fatigue life around 20% of both metals under physiological conditions.

Variation of the superelastic properties and nickel release from original and reused NiTi orthodontic archwires.

Reuse of NiTi orthodontic wires has become increasingly common in dental clinics. For sterilization and recovery of the original superelastic properties of the wires, a heat treatment is usually performed between 500 and 600 °C. The aim of this study was to analyze the effect of these thermal treatments on the mechanical behavior and the microstructure of NiTi archwires of different compositions. A reduction of the Ni content was observed in the matrix of the thermally treated archwires, due to the formation of Ti(3)Ni(4) precipitates. The nickel-rich precipitates were observed and characterized by Transmission Electron Microscopy (TEM) and electron diffraction. They were found to alter the mechanical properties of the wires, decreasing the transformation stresses, and causing a loss of activation of the NiTi archwires. The release of nickel was higher in the original archwires than in the reused ones, due to the matrix nickel depletion caused by the precipitation of Ti(3)Ni(4).

Reduction of Ni release and improvement of the friction behaviour of NiTi orthodontic archwires by oxidation treatments.

This work studies NiTi orthodontic archwires that have been treated using a new oxidation treatment for obtaining Ni-free surfaces. The titanium oxide on the surface significantly improves corrosion resistance and decreases nickel ion release, while barely affecting transformation temperatures. This oxidation treatment avoids the allergic reactions or toxicity in the surrounding tissues produced by the chemical degradation of the NiTi. In the other hand, the lack of low friction coefficient for the NiTi superelastic archwires makes difficult the optimal use of these materials in Orthodontic applications. In this study, the decrease of this friction coefficient has been achieved by means of oxidation treatment. Transformation temperatures, friction coefficient and ion release have been determined.

Five-year follow-up evaluation of the noncemented press-fit titanium hip-joint endoprosthesis.

A series of 260 noncemented total hip arthroplasties with a titanium alloy stem and fixation by the Zweymüller press-fit and an Endler polyethylene threaded cup was reviewed in detail. The minimum follow-up period was 48 months and the maximum 72 months, with an average of 60 months. A scale from zero to five points was applied to evaluate pain, mobility, and motion for a total possible accumulation of 15 points. The global results of the different etiologic groups (arthrosis, femoral head necrosis, rheumatoid arthritis, and subcapital hip fractures) have been very good and good (12-15 points) in 67.5% of the cases and fairly good and bad in 32.3%. These results have been better in femoral head necrosis than in arthrosis or rheumatoid arthritis, but not as good in subcapital hip fractures. The age groups below 60 had better results than the above 60 groups. The Singh index higher than 3 was correlated with better-than-average results. The polyethylene cup migrated horizontally (more than 4 mm) in 7.6% of the cases and vertically (more than 5 mm) in 10%. The non-evolutionary cortical remodelation of the femur does not influence the results. Prosthetic stem sinking less than 4 mm has been found in 62% of the cases, from 4 to 9 mm in 21%, and greater than 9 mm in 6%. No alterations with clinical consequences attributable to stress-shielding have been detected.