Correction of severe valgus osteoarthritis by total knee arthroplasty is associated with increased postoperative ankle symptoms.

PURPOSE: The aim of this study was to assess the mid-term clinical outcome of the ankle joint after total knee arthroplasty (TKA) in high-grade valgus osteoarthritis. METHODS: In this case-control study, n = 36 patients with a preoperative mechanical tibiofemoral angle (mTFA) ≥ 15° who underwent TKA between December 2002 and December 2012 were included. The control group (mTFA < 15°) of n = 60 patients was created using case matching. Radiological [mechanical tibiofemoral angle (mTFA) and ankle joint orientation to the ground (G-AJLO)] and clinical parameters [Foot Function Index (FFI), Knee Society Score, Forgotten Joint Score, and Range of Motion (ROM)] were analysed. The mean follow-up time was 59 months (IQR [56, 62]). RESULTS: The degree of correcting the mTFA by TKA significantly correlated with the postoperative FFI (R = 0.95, p < 0.05), although the knee and ankle joint lines were corrected to neutral orientations. A cut-off value of 16.5° [AUC 0.912 (0.85-0.975 95% CI), sensitivity = 0.8, specificity = 0.895] was calculated, above which the odds ratio (OR) for developing ankle symptoms increased vastly [OR 34.0 (9.10-127.02 95% CI)]. ROM restrictions of the subtalar joint displayed a strong significant correlation with the FFI (R = 0.74, p < 0.05), demonstrating that decreased ROM of the subtalar joint was associated with aggravated outcomes of the ankle joint. CONCLUSIONS: In this study, higher degrees of leg axis correction in TKA were associated with increased postoperative ankle symptoms. When TKA is performed in excessive valgus knee osteoarthritis, surgeons should be aware that this might trigger the onset or progression of ankle symptoms, particularly in cases of a stiff subtalar joint. LEVEL OF EVIDENCE: III.

Laminar air flow reduces particle load in TKA-even outside the LAF panel: a prospective, randomized cohort study.

PURPOSE: Released particles are a major risk of airborne contamination during surgery. The present prospective study investigated the quantitative and qualitative particle load in the operating room (OR) depending on location, time of surgery and use of laminar air flow (LAF) system. METHODS: The particle load/m3 was measured during the implantation of 12 total knee arthroplasties (6 × LAF, 6 × Non-LAF) by using the Met One HHPC 6 + device (Beckmann Coulter GmbH, Germany). Measurement was based on the absorption and scattering of (laser) light by particles and was performed at three different time-points [empty OR, setting up, ongoing operation) at 3 fixed measurement points [OR table (central LAF area), anaesthesia tower (marginal LAF area), surgical image amplifier (outside LAF area)]. RESULTS: Independent of time and location, all measurements showed a significantly higher particle load in the Non-LAF group (p < 0.01). With ongoing surgical procedure both groups showed increasing particle load. While there was a major increase of fine particles (size < 1 µm) with advancing activity in the LAF group, the Non-LAF group showed higher particle gain with increasing particle size. The lowest particle load in the LAF group was measured at the operating column, increasing with greater distance from the operating table. The Non-LAF group presented a significantly higher particle load than the LAF group at all locations. CONCLUSION: The use of a LAF system significantly reduces the particle load and therefore potential bacterial contamination regardless of the time or place of measurement and therefore seems to be a useful tool for infection prevention. As LAF leads to a significant decrease of respirable particles, it appears to be a protective factor for the health of the surgical team regardless of its use in infection prevention. LEVEL OF EVIDENCE: I.

[Adjusted mechanical alignment: operative technique-Tips and tricks]. / Adjustiertes mechanisches Alignment: Operative Technik ­ Tipps und Tricks.

INTRODUCTION: Mechanical alignment (MA) is a standardized procedure that aims to achieve a neutrally aligned leg axis. An alignment of the prosthesis closer to the patient's anatomy can be an approach for better clinical outcomes. The surgical technique of adjusted mechanical alignment (aMA) presented here is a modified extension-gap-first technique that takes into account the natural ligamentous tension of the knee joint so that ligamentous releases can be avoided as far as possible. INDICATION: The aMA technique can be used for primary and secondary varus gonarthrosis of up to 20° of varus. SURGICAL TECHNIQUE: The aim of the operation is to achieve a balanced ligament tension through a femoral osseous correction rather than ligament releases. TEA and the sulcus line are marked to control the ligament-based femoral rotation. The osteophytes are removed to ensure a reliable ligament tension. A quantitative ligament tensioner is stretched with great care, and gap width as well as medial and lateral ligament tension are read off. In order to correct an extension gap asymmetry, instead of the typical medial soft tissue release, the asymmetry is compensated by a special femoral cutting block. Now, the flexion gap is assessed, whereby the transverse femoral rotation follows the soft tissue tension. The tensioner adjusts a rectangular flexion gap with balanced ligament tension. After a final balancing of the gaps, the femoral preparation is completed and the trial components are inserted. Here, the rotation of the tibial component is set by repeated flexion-extension cycles. DISCUSSION AND CONCLUSION: The technique presented combines a measured-resection technique with individual ligament tension. The maximum deviation of the femoral alignment in the coronal plane from the neutral alignment is 2.5°. In order to avoid problems, it is recommended, as with the described technique, to achieve a component alignment based on the patient anatomy by adjusting the femoral component. The measured-resection technique carries the risk of flexion instability. With the gap-balancing technique symmetrical ligament tension can be achieved, assuming precise proximal tibial cuts. When aligning the femoral component rotation, flexion gap stability and patella tracking should be considered. Long-term studies of high case numbers are necessary to evaluate the good short-term results of the presented surgical technique.

The influence of locally applied platelet-derived growth factor-BB on free tendon graft remodeling after anterior cruciate ligament reconstruction.

BACKGROUND: Ligaments and tendons do not gain mechanical properties of the native tissue after injury or grafting. PURPOSE: To determine the influence of platelet-derived growth factor on tendon graft remodeling. STUDY DESIGN: Laboratory animal study. METHODS: Forty-eight sheep underwent anterior cruciate ligament reconstruction and were sacrificed after 3, 6, 12, and 24 weeks. In 6 animals at each time point, platelet-derived growth factor was locally delivered via coated sutures. After mechanical testing, tissue samples were taken for histologic, immunohistochemical, and electron microscopy evaluations. RESULTS: With platelet-derived growth factor treatment, cross-sectional area was significantly lower at 3 and 12 weeks. Load to failure was significantly higher at 6 weeks. Tensile stress was significantly higher at 3 and 12 weeks. Crimp length was significantly higher at 3 and 6 weeks. Vascular density was significantly higher at 6 weeks. Electron microscopy showed a significantly higher collagen fibril amount at 12 weeks. Differences in these parameters at other time points were not significant. CONCLUSIONS: There were alterations in several but not all time points. The local application of platelet-derived growth factor alters the tissue's mechanical properties during free tendon graft remodeling after anterior cruciate ligament reconstruction. Growth factors present a promising tool toward the complete mechanical restitution of a healing ligament substitute.