Orange Dye and Silicone Glue Composite Gel-Based Optimized Impedimetric and Capacitive Surface-Type Proximity Sensors.

Optimized surface-type impedimetric and capacitive proximity sensors have been fabricated on paper substrates by using rubbing-in technology. The orange dye (OD) and silicone glue (SG) composite-gel films were deposited on the zig-zag gap between two aluminum electrodes fixed on a paper (dielectric) substrate. The effect of proximity of various objects (receivers) on the impedance and the capacitance of the sensors was investigated. These objects were semi-cylindrical aluminum (metallic) foil, a cylindrical plastic tube filled with water, a kopeck-shaped plastic tube filled with carbon nanotubes and a human finger. The mechanism of sensing was based on the change in impedance and/or the capacitance of the sensors with variation of proximity between the surfaces of the sensor and the object. On decreasing proximity, the impedance of the sensors increased while the capacitance decreased. The impedimetric proximity sensitivities of CNT, water, metal-based receivers and the finger were up to 60 × 103 Ω/mm, 35 × 103 Ω/mm, 44 × 103 Ω/mm and 6.2 × 103 Ω/mm, respectively, while their capacitive sensitivities were -19.0 × 10-2 pF/mm, -16.0 × 10-2 pF/mm, -16.4 × 10-2 pF/mm and -1.8 × 10-2 pF/mm. If needed for practical application, the sensors can be built in to the Wheatstone bridge, which can also increase the sensitivity of the measurement. Moreover, the sensor's materials are low cost, while the fabrication technique is easy and ecologically friendly. The sensor can also be used for demonstrative purposes in school and college laboratories.

Fabrication and Investigation of Graphite-Flake-Composite-Based Non-Invasive Flex Multi-Functional Force, Acceleration, and Thermal Sensor.

This work examines the physics of a non-invasive multi-functional elastic thin-film graphite flake-isoprene sulfone composite sensor. The strain design and electrical characterization of the stretching force, acceleration, and temperature were performed. The rub-in technique was used to fabricate graphite flakes and isoprene sulfone into sensors, which were then analyzed for their morphology using methods such as SEM, AFM, X-ray diffraction, and Fourier transform infrared spectroscopy to examine the device's surface and structure. Sensor impedance was measured from DC to 200 kHz at up to 20 gf, 20 m/s2, and 26-60 °C. Sensor resistance and impedance to stretching force and acceleration at DC and 200 Hz rose 2.4- and 2.6-fold and 2.01- and 2.06-fold, respectively. Temperature-measuring devices demonstrated 2.65- and 2.8-fold decreases in resistance and impedance at DC and 200 kHz, respectively. First, altering the graphite flake composite particle spacing may modify electronic parameters in the suggested multi-functional sensors under stress and acceleration. Second, the temperature impacts particle and isoprene sulfone properties. Due to their fabrication using an inexpensive deposition technique, these devices are environmentally friendly, are simple to build, and may be used in university research in international poverty-line nations. In scientific laboratories, such devices can be used to teach students how various materials respond to varying environmental circumstances. They may also monitor individuals undergoing physiotherapy and vibrating surfaces in a controlled setting to prevent public health risks.

Shockproof Deformable Infrared Radiation Sensors Based on a Polymeric Rubber and Organic Semiconductor H2Pc-CNT Composite.

Polymeric rubber and organic semiconductor H2Pc-CNT-composite-based surface- and sandwich-type shockproof deformable infrared radiation (IR) sensors were fabricated using a rubbing-in technique. CNT and CNT-H2Pc (30:70 wt.%) composite layers were deposited on a polymeric rubber substrate as electrodes and active layers, respectively. Under the effect of IR irradiation (0 to 3700 W/m2), the resistance and the impedance of the surface-type sensors decreased up to 1.49 and 1.36 times, respectively. In the same conditions, the resistance and the impedance of the sandwich-type sensors decreased up to 1.46 and 1.35 times, respectively. The temperature coefficients of resistance (TCR) of the surface- and sandwich-type sensors are 1.2 and 1.1, respectively. The novel ratio of the H2Pc-CNT composite ingredients and comparably high value of the TCR make the devices attractive for bolometric applications meant to measure the intensity of infrared radiation. Moreover, given their easy fabrication and low-cost materials, the fabricated devices have great potential for commercialization.

Raytracing Modelling of Infrared Light Management Using Molybdenum Disulfide (MoS2) as a Back-Reflector Layer in a Silicon Heterojunction Solar Cell (SHJ).

The silicon heterojunction solar cell (SHJ) is considered the dominant state-of-the-art silicon solar cell technology due to its excellent passivation quality and high efficiency. However, SHJ's light management performance is limited by its narrow optical absorption in long-wave near-infrared (NIR) due to the front, and back tin-doped indium oxide (ITO) layer's free carrier absorption and reflection losses. Despite the light-trapping efficiency (LTE) schemes adopted by SHJ in terms of back surface texturing, the previous investigations highlighted the ITO layer as a reason for an essential long-wavelength light loss mechanism in SHJ solar cells. In this study, we propose the use of Molybdenum disulfide (MoS2) as a way of improving back-reflection in SHJ. The text presents simulations of the optical response in the backside of the SHJ applying the Monte-Carlo raytracing method with a web-based Sunsolve high-precision raytracing tool. The solar cells' electrical parameters were also resolved using the standard electrical equivalent circuit model provided by Sunsolve. The proposed structure geometry slightly improved the SHJ cell optical current density by ~0.37% (rel.), and hence efficiency (η) by about 0.4% (rel.). The SHJ cell efficiency improved by 21.68% after applying thinner back ITO of about 30 nm overlayed on ~1 nm MoS2. The efficiency improvement following the application of MoS2 is tentatively attributed to the increased NIR absorption in the silicon bulk due to the light constructive interface with the backside components, namely silver (Ag) and ITO. Study outcomes showed that improved SHJ efficiency could be further optimized by addressing front cell components, mainly front ITO and MoS2 contact engineering.

Recent Issues and Configuration Factors in Perovskite-Silicon Tandem Solar Cells towards Large Scaling Production.

The unprecedented development of perovskite-silicon (PSC-Si) tandem solar cells in the last five years has been hindered by several challenges towards industrialization, which require further research. The combination of the low cost of perovskite and legacy silicon solar cells serve as primary drivers for PSC-Si tandem solar cell improvement. For the perovskite top-cell, the utmost concern reported in the literature is perovskite instability. Hence, proposed physical loss mechanisms for intrinsic and extrinsic instability as triggering mechanisms for hysteresis, ion segregation, and trap states, along with the latest proposed mitigation strategies in terms of stability engineering, are discussed. The silicon bottom cell, being a mature technology, is currently facing bottleneck challenges to achieve power conversion efficiencies (PCE) greater than 26.7%, which requires more understanding in the context of light management and passivation technologies. Finally, for large-scale industrialization of the PSC-Si tandem solar cell, the promising silicon wafer thinning, and large-scale film deposition technologies could cause a shift and align with a more affordable and flexible roll-to-roll PSC-Si technology. Therefore, this review aims to provide deliberate guidance on critical fundamental issues and configuration factors in current PSC-Si tandem technologies towards large-scale industrialization. to meet the 2031 PSC-Si Tandem road maps market target.

An Overview of the Strategies for Tin Selenide Advancement in Thermoelectric Application.

Chalcogenide, tin selenide-based thermoelectric (TE) materials are Earth-abundant, non-toxic, and are proven to be highly stable intrinsically with ultralow thermal conductivity. This work presented an updated review regarding the extraordinary performance of tin selenide in TE applications, focusing on the crystal structures and their commonly used fabrication methods. Besides, various optimization strategies were recorded to improve the performance of tin selenide as a mid-temperature TE material. The analyses and reviews over the methodologies showed a noticeable improvement in the electrical conductivity and Seebeck coefficient, with a noticeable decrement in the thermal conductivity, thereby enhancing the tin selenide figure of merit value. The applications of SnSe in the TE fields such as microgenerators, and flexible and wearable devices are also discussed. In the future, research in low-dimensional TE materials focusing on nanostructures and nanocomposites can be conducted with the advancements in material science technology as well as microtechnology and nanotechnology.

A novel and stable way for energy harvesting from Bi2Te3Se alloy based semitransparent photo-thermoelectric module.

In this research, due to the present pandemic of COVID-19, we are proposing a stable and fixed semitransparent photo-thermoelectric cell (PTEC) module for green energy harvesting. This module is based on the alloy of Bismuth Telluride Selenide (Bi2Te3Se), designed in a press tablet form and characterized under solar energy. Here, both aspects of solar energy i.e., light and heat are utilized for both energy production and water heating. The semitransparent PTEC converts heat energy directly to electrical energy due to the gradient of temperature between two electrodes (top and bottom) of thermoelectric cells. The PTEC is 25% transparent, which can be varied according to the necessity of the utilizer. The X-ray diffraction of material and electric characterization of module i.e., open-circuited voltage (VOC) and Seebeck coefficient were performed. The experimental observations disclose that in the proposed PTEC module with an increment in the average temperature (TAvg) from 34 to 60 °C, results in the rise of VOC âˆ¼ 2.4 times. However, by modifying the size of heat-absorbing top electrode and by increasing the temperature gradient through the addition of water coolant under the bottom electrode, an uplift in the champion device results in as increment of VOC ∼5.5 times and Seebeck coefficient obtained was -250 µV/0C, respectively. Results show that not only the selection of material but also the external modifications in the device highly effective the power efficiency of the devices. The proposed modules can generate electric power from light and utilize the penetrating sunlight inside the room and for the heating of the water which also acts as a coolant. These semitransparent thermoelectric cells can be built-in within windows and roofs of buildings and can potentially contribute to green energy harvesting, in situations where movement is restricted locally or globally.

A novel and stable ultraviolet and infrared intensity sensor in impedance/capacitance modes fabricated from degraded CH3NH3PbI3-xClx perovskite materials.

The present situation of COVID-19 diverted our focus towards utilizing the degraded solar cells for sensor application, this will help in global energy harvesting. So, here is our successful effort to reuse already degraded solar cells as ultraviolet (UV) and infrared (IR) sensor. The spin-coated perovskite (CH3NH3PbI3-XClX) has been already tested for visible light spectrum, as an extension to that now it is utilized as UV and IR intensity sensors to cover the whole spectrum. The employed CH3NH3PbI3-XClX material was used after its efficiency loss has been reached to a saturation point in photovoltaic devices. Each deposited layer was investigated from UV to the IR absorption spectrum for deepening study through UV-vis spectroscopy. In the sandwiched architecture possessing FTO/PEDOT: PSS/Perovskite/PC61BM/CdS/Au symmetry, the perovskite film has been employed as an absorbent layer, however, other layers participation also plays a key role. The resultant device yielded very good sensing performance because of the enhanced excitons generation which is attributed to the precise selection of the interfacial materials, e.g. CdS and PC61BM as an ETM and PEDOT: PSS as HTM. The impedance and capacitance of the devices within 0.01-200 kHz under varied UV and IR illumination intensities were investigated. Measurements showed that as the intensity of the light increased i.e., UV (0-200 W/m2) and IR (0-5800 W/m2), impedance decreased while capacitance increased. The current results are attributed to the increase in the concentration of charges i.e., electron-hole pairs generation depending on the built-in capacitance and frequency of the charges.

Compositional engineering of VOPcPhO-TiO2 nano-composite to reduce the absolute threshold value of humidity sensors.

This research work demonstrates compositional engineering of an organic-inorganic hybrid nano-composites for modifying absolute threshold of humidity sensors. Vanadyl-2,9,16,23-tetraphenoxy-29H,31H-phthalocyanine (VOPcPhO), an organic semiconductor, doped with Titanium-dioxide nanoparticles (TiO2 NPs) has been employed to fabricate humidity sensors. The morphology of the VOPcPhO:TiO2 nano-composite films has been analyzed by atomic force microscopy (AFM) and field emission scanning electron microscopy (FESEM). The sensors have been examined over a wide range of relative humidity i.e. 20-99% RH. The sensor with TiO2 (90nm) shows reduced sensitivity-threshold and improved linearity. The VOPcPhO:TiO2 (90nm) nano-composite film is comprised of uniformly distributed voids which makes the surface more favorable for adsorption of moisture content from environment. The VOPcPhO:TiO2 nano-composite based sensor demonstrates remarkable improvement in the sensing parameter when equated with VOPcPhO sensors.