Short-term stability of wastewater samples for storage and shipment in the context of the EU Sewage Sentinel System for SARS-CoV-2.

In the context of an EU-wide surveillance system for SARS-CoV-2 in wastewater, recommended by the European Commission, this study aims to provide scientific support to the adequacy of transport and storage conditions of samples both in terms of duration and samples temperature. Three laboratories in Slovenia, Cyprus and Estonia investigated the short-term, one-week, isochronous stability of wastewater samples by RT-qPCR based detection of SARS-CoV-2 genes. The results were tested for statistical significance to determine uncertainty of quantification and shelf-life, at testing temperatures of + 20 °C and - 20 °C, relative to reference at + 4 °C. Samples were collected from three urban wastewater treatment plant influents and analysed respectively for SARS-CoV-2 genes N1, N2 (Laboratory 1), N2, E (Laboratory 2) and N3 (Laboratory 3), with various analytical methods. For a period of 7/8 days at + 20 °C, decreasing trends of measured concentrations were observed for all genes resulting in instability according to the statistical analysis, while at - 20 °C the trend of variation was stable only for N1, N2 (Laboratory 1) and N3 (Laboratory 3). Trends for gene E concentrations at - 20 °C (Laboratory 2) could not be tested statistically for stability because of lack of data. Over a period of just 3 days at + 20 °C, the variation was statistically non-significant indicating stability for genes N1, E and N3 for laboratories 1, 2 and 3, respectively. Nonetheless, the outcome of the study presents evidence to support the choice of the selected temperature at which samples shall be preserved during storage before analysis or transport to the laboratory. The conditions (+4 °C, ∼ few days) chosen for EU wastewater surveillance are in accordance with these results, highlighting the importance of stability testing of environmental samples to determine the short-term analytical uncertainty.

Wastewater-based monitoring of illicit drugs in Cyprus by UPLC-MS/MS: The impact of the COVID-19 pandemic.

The outbreak and spread of COVID-19 impacted through various ways the lives of millions of humans globally. In this work, wastewater-based epidemiology (WBE) was applied to investigate the effect of the actions taken by the Republic of Cyprus to confine COVID-19 on the use of illicit stimulant drugs. Daily influent samples were collected from the six main wastewater treatment plants (WWTPs) of the country i) before lockdown (3-9 April 2019), ii) during lockdown (21-27 April 2020), iii) during the post-lockdown period (14-20 July 2020), and, iv) during each season of the following year (20-26 April 2021, 19-25 July 2021, 11-17 October 2021, 25 December 2021-2 January 2022), and analyzed for amphetamine, methamphetamine, MDMA and cocaine. In most areas, amphetamine and methamphetamine use was not affected during the confinement period, but as availability of the substances decreased with time, a drop in their use was observed when most restriction measures were eased (up to 9- and 22-fold decrease, respectively). The limitations on social interactions and events during the quarantine period seem to have led to the reduction of MDMA and cocaine and driven a sharp decrease of their use in most areas studied (up to 11 and 6 times lower, respectively). However, the re-opening of activities led to a pronounced consumption increase, reaching maximum daily values of 800 and 2691 mg/1000 inhabitants/day, respectively. In 2021, drug use was re-established to lower levels. The examination of weekly patterns during this year revealed higher weekend use of methamphetamine, MDMA and cocaine. Our results suggest that both the implementation and the easing of COVID-19 related measures affected the availability and the use of drugs. This study also provides the first insight on the consumption of illicit drugs in the Republic of Cyprus during pre-, post- and pandemic times and demonstrates the importance of WBE.

Reduction of antibiotic resistance determinants in urban wastewater by ozone: Emphasis on the impact of wastewater matrix towards the inactivation kinetics, toxicity and bacterial regrowth.

This study investigated the impact of bench-scale ozonation on the inactivation of total cultivable and antibiotic-resistant bacteria (faecal coliforms, Escherichia coli, Pseudomonas aeruginosa, Enterococcus spp., and total heterotrophs), and the reduction of gene markers (16S rRNA and intl1) and antibiotic resistance genes (qacEΔ1, sul1, aadA1 and dfrA1) indigenously present in wastewater effluents treated by membrane bioreactor (MBR) or conventional activated sludge (CAS). The Chick-Watson model-predicted ozone exposure (CT) requirements, showed that higher CT values were needed for CAS- than MBR-treated effluents to achieve a 3-log reduction of each microbial group, i.e., ~30 and 10 gO3 min gDOC-1 respectively. Ozonation was efficient in inactivating the examined antibiotic-resistant bacteria, and no bacterial regrowth was observed after 72 h. The genes abundance decreased significantly by ozone, but an increase in their abundance was detected 72 h after storage of the treated samples. A very low removal of DOC was achieved and at the same time phyto- and eco-toxicity increased after the ozonation treatment in both wastewater matrices. The gene abundance, regrowth and toxicity results of this study may be of high environmental significance for comprehensive evaluation of ozone and may guide future studies in assessing these parameters for other oxidants/disinfectants.

Sewage analysis as a tool for the COVID-19 pandemic response and management: the urgent need for optimised protocols for SARS-CoV-2 detection and quantification.

COVID-19 is an ongoing global pandemic caused by severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2). As of July 29th 2020, more than 16,6 million cases have been reported in more than 188 countries/territories, leading to more than 659000 deaths. One of the main challenges facing health authorities has been testing for the virus on a sufficiently comprehensive scale. The pandemic has been an impetus for the wastewater community as it has inspired scientists to look to wastewater to help fill in the gap of measuring the prevalence of SARS-CoV-2 within a given community. Testing the wastewater may serve as an early warning system allowing timely interventions. Although viral shedding varies among individuals and over the course of their infection, the sewage system can blend these variations into an average that represents the wider studied community. The urgent need has led to a lack of coherent reporting of data regarding the analysis, as these huge and remarkable efforts by the wastewater scientific community were made in a very short time. Important information on the analytical approach is often lacking, while there is still no optimisation of the methodology, including sampling, sample storage and concentration, RNA extraction and detection/quantification. This review aims at identifying the main issues for consideration, relating to the development of validated methodological protocols for the virus quantitative analysis in wastewater. Their inclusion will enable the methodological optimisation of SARS-CoV-2 wastewater analyses, transforming the wastewater infrastructure into a source of useful information for the health sector.

Continuous ozonation of urban wastewater: Removal of antibiotics, antibiotic-resistant Escherichia coli and antibiotic resistance genes and phytotoxicity.

This work evaluated the removal of a mixture of eight antibiotics (i.e. ampicillin (AMP), azithromycin (AZM), erythromycin (ERY), clarithromycin (CLA), ofloxacin (OFL), sulfamethoxazole (SMX), trimethoprim (TMP) and tetracycline (TC)) from urban wastewater, by ozonation operated in continuous mode at different hydraulic retention times (HRTs) (i.e. 10, 20, 40 and 60 min) and specific ozone doses (i.e. 0.125, 0.25, 0.50 and 0.75 gO3 gDOC- 1). As expected, the efficiency of ozonation was highly ozone dose- and contact time-dependent. The removal of the parent compounds of the selected antibiotics to levels below their detection limits was achieved with HRT of 40 min and specific ozone dose of 0.125 gO3 gDOC- 1. The effect of ozonation was also investigated at a microbiological and genomic level, by studying the efficiency of the process with respect to the inactivation of Escherichia coli and antibiotic-resistant E. coli, as well as to the reduction of the abundance of selected antibiotic resistance genes (ARGs). The inactivation of total cultivable E. coli was achieved under the experimental conditions of HRT 40 min and 0.25 gO3 gDOC-1, at which all antibiotic compounds were already degraded. The regrowth examinations revealed that higher ozone concentrations were required for the permanent inactivation of E. coli below the Limit of Quantification (

The role of operating parameters and oxidative damage mechanisms of advanced chemical oxidation processes in the combat against antibiotic-resistant bacteria and resistance genes present in urban wastewater.

An upsurge in the study of antibiotic resistance in the environment has been observed in the last decade. Nowadays, it is becoming increasingly clear that urban wastewater is a key source of antibiotic resistance determinants, i.e. antibiotic-resistant bacteria and antibiotic resistance genes (ARB&ARGs). Urban wastewater reuse has arisen as an important component of water resources management in the European Union and worldwide to address prolonged water scarcity issues. Especially, biological wastewater treatment processes (i.e. conventional activated sludge), which are widely applied in urban wastewater treatment plants, have been shown to provide an ideal environment for the evolution and spread of antibiotic resistance. The ability of advanced chemical oxidation processes (AOPs), e.g. light-driven oxidation in the presence of H2O2, ozonation, homogeneous and heterogeneous photocatalysis, to inactivate ARB and remove ARGs in wastewater effluents has not been yet evaluated through a systematic and integrated approach. Consequently, this review seeks to provide an extensive and critical appraisal on the assessment of the efficiency of these processes in inactivating ARB and removing ARGs in wastewater effluents, based on recent available scientific literature. It tries to elucidate how the key operating conditions may affect the process efficiency, while pinpointing potential areas for further research and major knowledge gaps which need to be addressed. Also, this review aims at shedding light on the main oxidative damage pathways involved in the inactivation of ARB and removal of ARGs by these processes. In general, the lack and/or heterogeneity of the available scientific data, as well as the different methodological approaches applied in the various studies, make difficult the accurate evaluation of the efficiency of the processes applied. Besides the operating conditions, the variable behavior observed by the various examined genetic constituents of the microbial community, may be directed by the process distinct oxidative damage mechanisms in place during the application of each treatment technology. For example, it was shown in various studies that the majority of cellular damage by advanced chemical oxidation may be on cell wall and membrane structures of the targeted bacteria, leaving the internal components of the cells relatively intact/able to repair damage. As a result, further in-depth mechanistic studies are required, to establish the optimum operating conditions under which oxidative mechanisms target internal cell components such as genetic material and ribosomal structures more intensively, thus conferring permanent damage and/or death and preventing potential post-treatment re-growth.

Treatment efficiency and economic feasibility of biological oxidation, membrane filtration and separation processes, and advanced oxidation for the purification and valorization of olive mill wastewater.

Olive mill wastewater (OMW) is a major waste stream resulting from numerous operations that occur during the production stages of olive oil. The resulting effluent contains various organic and inorganic contaminants and its environmental impact can be notable. The present work aims at investigating the efficiency of (i) jet-loop reactor with ultrafiltration (UF) membrane system (Jacto.MBR), (ii) solar photo-Fenton oxidation after coagulation/flocculation pre-treatment and (iii) integrated membrane filtration processes (i.e. UF/nanofiltration (NF)) used for the treatment of OMW. According to the results, the efficiency of the biological treatment was high, equal to 90% COD and 80% total phenolic compounds (TPh) removal. A COD removal higher than 94% was achieved by applying the solar photo-Fenton oxidation process as post-treatment of coagulation/flocculation of OMW, while the phenolic fraction was completely eliminated. The combined UF/NF process resulted in very high conductivity and COD removal, up to 90% and 95%, respectively, while TPh were concentrated in the NF concentrate stream (i.e. 93% concentration). Quite important is the fact that the NF concentrate, a valuable and polyphenol rich stream, can be further valorized in various industries (e.g. food, pharmaceutical, etc.). The above treatment processes were found also to be able to reduce the initial OMW phytotoxicity at greenhouse experiments; with the effluent stream of solar photo-Fenton process to be the least phytotoxic compared to the other treated effluents. A SWOT (Strength, Weakness, Opportunities, Threats) analysis was performed, in order to determine both the strengths of each technology, as well as the possible obstacles that need to overcome for achieving the desired levels of treatment. Finally, an economic evaluation of the tested technologies was performed in an effort to measure the applicability and viability of these systems at real scale; highlighting that the cost cannot be regarded as a 'cut off criterion', since the most cost-effective option in not always the optimum one.

On the capacity of ozonation to remove antimicrobial compounds, resistant bacteria and toxicity from urban wastewater effluents.

The degradation of erythromycin (ERY) and ethylparaben (EtP) in urban wastewater effluents at low concentration level during ozonation was investigated under different experimental conditions. Both substrates were rapidly eliminated within 2min at low ozone dose of 0.3mgL-1 and the experimental data were well fitted in the pseudo-first-order kinetic model. The ratio of HO- and O3-exposure (Rct) at the inherent pH was found to be 1.9×10-8. The degradation of ERY and EtP was pronounced at pH 8 compared to acidic pH conditions, while the degradation rate of both substrates was found to be matrix-depended. It was also shown that both O3- and HO-mediated pathways are involved in the degradation of EtP, whereas the saturated-rich structure of ERY renders it O3-recalcitrant. Under the optimum O3 dose, the BrO3- concentration was found to be lower than 10µgL-1. Five and fifteen transformation products were elucidated during ERY and EtP oxidation, respectively. The root and shoot inhibition can be attributed to the oxidation products formed upon dissolved effluent organic matter transformation. Escherichia coli harbouring resistance to ERY survived ozonation better than EtP-resistant E. coli. However, neither ERY- nor EtP-resistant E. coli were detected after 15min of ozonation.

The environmental footprint of a membrane bioreactor treatment process through Life Cycle Analysis.

This study includes an environmental analysis of a membrane bioreactor (MBR), the objective being to quantitatively define the inventory of the resources consumed and estimate the emissions produced during its construction, operation and end-of-life deconstruction. The environmental analysis was done by the life cycle assessment (LCA) methodology, in order to establish with a broad perspective and in a rigorous and objective way the environmental footprint and the main environmental hotspots of the examined technology. Raw materials, equipment, transportation, energy use, as well as air- and waterborne emissions were quantified using as a functional unit, 1m(3) of urban wastewater. SimaPro 8.0.3.14 was used as the LCA analysis tool, and two impact assessment methods, i.e. IPCC 2013 version 1.00 and ReCiPe version 1.10, were employed. The main environmental hotspots of the MBR pilot unit were identified to be the following: (i) the energy demand, which is by far the most crucial parameter that affects the sustainability of the whole process, and (ii) the material of the membrane units. Overall, the MBR technology was found to be a sustainable solution for urban wastewater treatment, with the construction phase having a minimal environmental impact, compared to the operational phase. Moreover, several alternative scenarios and areas of potential improvement, such as the diversification of the electricity mix and the material of the membrane units, were examined, in order to minimize as much as possible the overall environmental footprint of this MBR system. It was shown that the energy mix can significantly affect the overall sustainability of the MBR pilot unit (i.e. up to 95% reduction of the total greenhouse gas emissions was achieved with the use of an environmentally friendly energy mix), and the contribution of the construction and operational phase to the overall environmental footprint of the system.

Erythromycin oxidation and ERY-resistant Escherichia coli inactivation in urban wastewater by sulfate radical-based oxidation process under UV-C irradiation.

This study evaluates the feasibility of UV-C-driven advanced oxidation process induced by sulfate radicals SO4(.)- in degrading erythromycin (ERY) in secondary treated wastewater. The results revealed that 10 mg L(-1) of sodium persulfate (SPS) can result in rapid and complete antibiotic degradation within 90 min of irradiation, while ERY decay exhibited a pseudo-first-order kinetics pattern under the different experimental conditions applied. ERY degradation rate was strongly affected by the chemical composition of the aqueous matrix and it decreased in the order of: ultrapure water (kapp = 0.55 min(-1)) > bottled water (kapp = 0.26 min(-1)) > humic acid solution (kapp = 0.05 min(-1)) > wastewater effluents (kapp = 0.03 min(-1)). Inherent pH conditions (i.e. pH 8) yielded an increased ERY degradation rate, compared to that observed at pH 3 and 5. The contribution of hydroxyl and sulfate radicals (HO. and SO4(.)-) on ERY degradation was found to be ca. 37% and 63%, respectively. Seven transformation products (TPs) were tentatively elucidated during ERY oxidation, with the 14-membered lactone ring of the ERY molecule being intact in all cases. The observed phytotoxicity against the tested plant species can potentially be attributed to the dissolved effluent organic matter (dEfOM) present in wastewater effluents and its associated-oxidation products and not to the TPs generated from the oxidation of ERY. This study evidences the potential use of the UV-C/SPS process in producing a final treated effluent with lower phytotoxicity (<10%) compared to the untreated wastewater. Finally, under the optimum experimental conditions, the UV-C/SPS process resulted in total inactivation of ERY-resistant Escherichia coli within 90 min.

Dissolved effluent organic matter: Characteristics and potential implications in wastewater treatment and reuse applications.

Wastewater reuse is currently considered globally as the most critical element of sustainable water management. The dissolved effluent organic matter (dEfOM) present in biologically treated urban wastewater, consists of a heterogeneous mixture of refractory organic compounds with diverse structures and varying origin, including dissolved natural organic matter, soluble microbial products, endocrine disrupting compounds, pharmaceuticals and personal care products residues, disinfection by-products, metabolites/transformation products and others, which can reach the aquatic environment through discharge and reuse applications. dEfOM constitutes the major fraction of the effluent organic matter (EfOM) and due to its chemical complexity, it is necessary to utilize a battery of complementary techniques to adequately describe its structural and functional character. dEfOM has been shown to exhibit contrasting effects towards various aquatic organisms. It decreases metal uptake, thus potentially reducing their bioavailability to exposed organisms. On the other hand, dEfOM can be adsorbed on cell membranes inducing toxic effects. This review paper evaluates the performance of various advanced treatment processes (i.e., membrane filtration and separation processes, activated carbon adsorption, ion-exchange resin process, and advanced chemical oxidation processes) in removing dEfOM from wastewater effluents. In general, the literature findings reveal that dEfOM removal by advanced treatment processes depends on the type and the amount of organic compounds present in the aqueous matrix, as well as the operational parameters and the removal mechanisms taking place during the application of each treatment technology.

Treatment of winery wastewater by physicochemical, biological and advanced processes: a review.

Winery wastewater is a major waste stream resulting from numerous cleaning operations that occur during the production stages of wine. The resulting effluent contains various organic and inorganic contaminants and its environmental impact is notable, mainly due to its high organic/inorganic load, the large volumes produced and its seasonal variability. Several processes for the treatment of winery wastewater are currently available, but the development of alternative treatment methods is necessary in order to (i) maximize the efficiency and flexibility of the treatment process to meet the discharge requirements for winery effluents, and (ii) decrease both the environmental footprint, as well as the investment/operational costs of the process. This review, presents the state-of-the-art of the processes currently applied and/or tested for the treatment of winery wastewater, which were divided into five categories: i.e., physicochemical, biological, membrane filtration and separation, advanced oxidation processes, and combined biological and advanced oxidation processes. The advantages and disadvantages, as well as the main parameters/factors affecting the efficiency of winery wastewater treatment are discussed. Both bench- and pilot/industrial-scale processes have been considered for this review.

Environmental side effects of pharmaceutical cocktails: what we know and what we should know.

Cocktails of pharmaceuticals are released in the environment after human consumption and due to the incomplete removal at the wastewater treatment plants. Pharmaceuticals are considered as contaminants of emerging concern and, a plethora of journal articles addressing their possible adverse effects have been published during the past 20 years. The emphasis during the early years of research within this field, was on the assessment of acute effects of pharmaceuticals applied singly, leading to results regarding their environmental risk, potentially not realistic or relevant to the actual environmental conditions. Only recently has the focus been shifted to chronic exposure and to the assessment of cocktail effects. To this end, this review provides an up-to-date compilation of 57 environmental and human toxicology studies published during 2000-2014 dealing with the adverse effects of pharmaceutical mixtures. The main challenges regarding the design of experiments and the analysis of the results regarding the effects of pharmaceutical mixtures to different biological systems are presented and discussed herein. The gaps of knowledge are critically reviewed highlighting specific future research needs and perspectives.

Utilizing solar energy for the purification of olive mill wastewater using a pilot-scale photocatalytic reactor after coagulation-flocculation.

This study investigated the application of a solar-driven advanced oxidation process (solar Fenton) combined with previous coagulation/flocculation, for the treatment of olive mill wastewater (OMW) at a pilot scale. Pre-treatment by coagulation/flocculation using FeSO4·7H2O (6.67 g L(-1)) as the coagulant, and an anionic polyelectrolyte (FLOCAN 23, 0.287 g L(-1)) as the flocculant, was performed to remove the solid content of the OMW. The solar Fenton experiments were carried out in a compound parabolic collector pilot plant, in the presence of varying doses of H2O2 and Fe(2+). The optimization of the oxidation process, using reagents at low concentrations ([Fe(2+)] = 0.08 g L(-1); [H2O2] = 1 g L(-1)), led to a high COD removal (87%), while the polyphenolic fraction, which is responsible for the biorecalcitrant and/or toxic properties of OMW, was eliminated. A kinetic study using a modified pseudo first-order kinetic model was performed in order to determine the reaction rate constants. This work evidences also the potential use of the solar Fenton process at the inherent pH of the OMW, yielding only a slightly lower COD removal (81%) compared to that obtained under acidic conditions. Moreover, the results demonstrated the capacity of the applied advanced process to reduce the initial OMW toxicity against the examined plant species (Sorghum saccharatum, Lepidium sativum, Sinapis alba), and the water flea Daphnia magna. The OMW treated samples displayed a varying toxicity profile for each type of organism and plant examined in this study, a fact that can potentially be attributed to the varying oxidation products formed during the process applied. Finally, the overall cost of solar Fenton oxidation for the treatment of 50 m(3) of OMW per day was estimated to be 2.11 € m(-3).

Transformation products and reaction pathways of carbamazepine during photocatalytic and sonophotocatalytic treatment.

This study examines the degradation of the antiepileptic carbamazepine (CBZ) by sonolysis, TiO2-based heterogeneous photocatalysis under UV-A and simulated solar irradiation, and by the combined use of UV-A and ultrasound irradiation (i.e. sonophotocatalysis) in demineralized water, ground water and effluent wastewater. The processes were compared with respect to substrate conversion rate and the extent of DOC reduction as a measure of mineralization. CBZ was degraded following a pseudo-first order kinetics. Sonophotocatalysis provided the highest rate of CBZ transformation over the time-course of the experiment while the degree of DOC removal in pure water was similar for all the studied treatments (around 40%), and always lower than CBZ conversion. This indicated that a considerable organic load remained in the treated solutions that could also be attributed to the presence of persistent oxidation products. UPLC-(+ESI)-QToF-MS was employed to determine major CBZ-related transformation products. Several recalcitrant hydroxy- and keto-derivatives of CBZ were tentatively identified. A Daphnia magna bioassay was used to evaluate the potential toxicity of the samples collected at different time points showing that the mixtures were highly toxic to D. magna.

Light-induced catalytic transformation of ofloxacin by solar Fenton in various water matrices at a pilot plant: mineralization and characterization of major intermediate products.

This work investigated the application of a solar driven advanced oxidation process (solar Fenton), for the degradation of the antibiotic ofloxacin (OFX) in various environmental matrices at a pilot-scale. All experiments were carried out in a compound parabolic collector pilot plant in the presence of doses of H2O2 (2.5 mg L(-1)) and at an initial Fe(2+) concentration of 2 mg L(-1). The water matrices used for the solar Fenton experiments were: demineralized water (DW), simulated natural freshwater (SW), simulated effluent from municipal wastewater treatment plant (SWW) and pre-treated real effluent from municipal wastewater treatment plant (RE) to which OFX had been spiked at 10 mg L(-1). Dissolved organic carbon removal was found to be dependent on the chemical composition of the water matrix. OFX mineralization was higher in DW (78.1%) than in SW (58.3%) at 12 mg L(-1) of H2O2 consumption, implying the complexation of iron or the scavenging of hydroxyl radicals by the inorganic ions present in SW. On the other hand, the presence of dissolved organic matter (DOM) in SWW and RE, led to lower mineralization per dose of H2O2 compared to DW and SW. The major transformation products (TPs) formed during the solar Fenton treatment of OFX, were elucidated using liquid chromatography-time of flight-mass spectrometry (LC-ToF-MS). The transformation of OFX proceeded through a defluorination reaction, accompanied by some degree of piperazine and quinolone substituent transformation while a hydroxylation mechanism occurred by attack of the hydroxyl radicals generated during the process leading to the formation of TPs in all the water matrices, seven of which were tentatively identified. The results obtained from the toxicity bioassays indicated that the toxicity originates from the DOM present in RE and its oxidation products formed during the photocatalytic treatment and not from the TPs resulted from the oxidation of OFX.

Superiority of solar Fenton oxidation over TiO2 photocatalysis for the degradation of trimethoprim in secondary treated effluents.

The overall aim of this work was to examine the degradation of trimethoprim (TMP), which is an antibacterial agent, during the application of two advanced oxidation process (AOP) systems in secondary treated domestic effluents. The homogeneous solar Fenton process (hv/Fe(2+)/H2O2) and heterogeneous photocatalysis with titanium dioxide (TiO2) suspensions were tested. It was found that the degradation of TMP depends on several parameters such as the amount of iron salt and H2O2, concentration of TiO2, pH of solution, solar irradiation, temperature and initial substrate concentration. The optimum dosages of Fe(2+) and H2O2 for homogeneous ([Fe(2+)] = 5 mg L(-1), [H2O2] = 3.062 mmol L(-1)) and TiO2 ([TiO2] = 3 g L(-1)) for heterogeneous photocatalysis were established. The study indicated that the degradation of TMP during the solar Fenton process is described by a pseudo-first-order reaction and the substrate degradation during the heterogeneous photocatalysis by the Langmuir-Hinshelwood kinetics. The toxicity of the treated samples was evaluated using a Daphnia magna bioassay and was finally decreased by both processes. The results indicated that solar Fenton is more effective than the solar TiO2 process, yielding complete degradation of the examined substrate within 30 min of illumination and dissolved organic carbon (DOC) reduction of about 44% whereas the respective values for the TiO2 process were ∼70% degradation of TMP within 120 min of treatment and 13% DOC removal.

Investigating the fate of iodinated X-ray contrast media iohexol and diatrizoate during microbial degradation in an MBBR system treating urban wastewater.

The capability of a moving bed biofilm reactor (MBBR) to remove the iodinated contrast media (ICM) iohexol (IOX) and diatrizoate (DTZ) from municipal wastewater was studied. A selected number of clones of microorganisms present in the biofilm were identified. Biotransformation products were tentatively identified and the toxicity of the treated effluent was assessed. Microbial samples were DNA-sequenced and subjected to phylogenetic analysis in order to confirm the identity of the microorganisms present and determine the microbial diversity. The analysis demonstrated that the wastewater was populated by a bacterial consortium related to different members of Proteobacteria, Firmicutes, and Nitrisporae. The optimum removal values of the ICM achieved were 79 % for IOX and 73 % for DTZ, whereas 13 biotransformation products for IOX and 14 for DTZ were identified. Their determination was performed using ultra-performance liquid chromatography-tandem mass spectrometry. The toxicity of the treated effluent tested to Daphnia magna showed no statistical difference compared to that without the addition of the two ICM. The MBBR was proven to be a technology able to remove a significant percentage of the two ICM from urban wastewater without the formation of toxic biodegradation products. A large number of biotransformation products was found to be formed. Even though the amount of clones sequenced in this study does not reveal the entire bacterial diversity present, it provides an indication of the predominating phylotypes inhabiting the study site.

Is the evaluation of "traditional" physicochemical parameters sufficient to explain the potential toxicity of the treated wastewater at sewage treatment plants?

Water scarcity is one of the most important environmental and public health problems of our century. Treated wastewater reuse seems to be the most attractive option for the enhancement of water resources. However, the lack of uniform guidelines at European and/or Mediterranean level leaves room for application of varying guidelines and regulations, usually not based on risk assessment towards humans and the environment. The benefits of complementing the physicochemical evaluation of wastewater with a biological one are demonstrated in the present study using Cyprus, a country with extended water reuse applications, as an example. Four organisms from different trophic levels were used for the biological assessment of the wastewater, namely, Pseudokirchneriella subcapitata, Daphnia magna, Artemia salina and Vibrio fischeri. The physicochemical assessment of wastewater based on "traditional" chemical parameters indicated that the quality of the wastewater complies with the limits set by the relevant national guidelines for disposal. The ecotoxicological assessment, however, indicated the presence of toxicity throughout the sampling periods and most importantly an increase of the toxicity of the treated wastewater during summer compared to winter. The resulting poor correlation between the physicochemical and biological assessments demonstrates that the two assessments are necessary and should be performed in parallel in order to be able to obtain concrete results on the overall quality of the treated effluent. Moreover, a hazard classification scheme for wastewater is proposed, which can enable the comparison of the data sets of the various parameters deriving from the biological assessment in a comprehensive way.

Urban wastewater treatment plants as hotspots for antibiotic resistant bacteria and genes spread into the environment: a review.

Urban wastewater treatment plants (UWTPs) are among the main sources of antibiotics' release into the environment. The occurrence of antibiotics may promote the selection of antibiotic resistance genes (ARGs) and antibiotic resistant bacteria (ARB), which shade health risks to humans and animals. In this paper the fate of ARB and ARGs in UWTPs, focusing on different processes/technologies (i.e., biological processes, advanced treatment technologies and disinfection), was critically reviewed. The mechanisms by which biological processes influence the development/selection of ARB and ARGs transfer are still poorly understood. Advanced treatment technologies and disinfection process are regarded as a major tool to control the spread of ARB into the environment. In spite of intense efforts made over the last years to bring solutions to control antibiotic resistance spread in the environment, there are still important gaps to fill in. In particular, it is important to: (i) improve risk assessment studies in order to allow accurate estimates about the maximal abundance of ARB in UWTPs effluents that would not pose risks for human and environmental health; (ii) understand the factors and mechanisms that drive antibiotic resistance maintenance and selection in wastewater habitats. The final objective is to implement wastewater treatment technologies capable of assuring the production of UWTPs effluents with an acceptable level of ARB.