RESUMEN
Polarization phenomena play a key role in membrane separation processes but remain largely unexplored for gas separations, where the mass transfer resistance is most often limited to the membrane. This assumption, which is commonly used today for the simulation of membrane gas separations, has to be reconsidered when high-performance materials, showing a very high permeance and/or selectivity, are used. In this study, a series of steady-state separation performances experimentally obtained on CO2/CH4 mixtures with a zeolite membrane are compared to the predictions of a dedicated 1D approach, recently derived and validated through CFD simulations. Polarization effects are shown to generate a significant negative impact on the separation performances, both in terms of the productivity and separation efficiency. The 1D model predictions, based on pure gas permeance data and without any adjustable parameters, are in very good agreement with the experimental data. This fast and efficient modeling approach can easily be implemented in simulation or process synthesis programs for the rigorous evaluation of membrane gas separation processes, when high-performance materials are used.
RESUMEN
Herein, experimental and theoretical approaches were used to design a new composite membrane for desalination by pervaporation. The theoretical approaches demonstrate the possibility to reach high mass transfer coefficients quite close to those obtained with conventional porous membranes if two conditions are verified: (i) a dense layer with a low thickness and (ii) a support with a high-water permeability. For this purpose, several membranes with a cellulose triacetate (CTA) polymer were prepared and compared with a hydrophobic membrane prepared in a previous study. The composite membranes were tested for several feed conditions, i.e., pure water, brine and saline water containing a surfactant. The results show that, whatever the tested feed, no wetting occurred during several hours of desalination tests. In addition, a steady flux was obtained together with a very high salt rejection (close to 100%) for the CTA membranes. Lastly, the CTA composite membrane was tested with real seawater without any pretreatment. It was shown that the salt rejection was still very high (close to 99.5%) and that no wetting could be detected for several hours. This investigation opens a new direction to prepare specific and sustainable membranes for desalination by pervaporation.
RESUMEN
Membrane processes have been investigated for carbon capture for more than four decades. Important efforts have been more recently achieved for the development of advanced materials and, to a lesser extent, on process engineering studies. A state-of-the-art analysis is proposed with a critical comparison to gas absorption technology, which is still considered as the best available technology for this application. The possibilities offered by high-performance membrane materials (zeolites, Carbon Molecular Sieves, Metal Oxide Frameworks, graphenes, facilitated transport membranes, etc.) are discussed in combination to process strategies (multistage design, hybrid processes, energy integration). The future challenges and open questions of membranes for carbon capture are finally proposed.
RESUMEN
The decomposition of volatile organic compounds by photocatalytic oxidation (PCO) has been widely studied. However, the technological development of this oxidative technique has to address how to handle the formation of transformation products. The work presented here investigates the original combination of a dense membrane separation process and PCO to intensify the trapping and reduction of PCO transformation products. Specific monitoring of toluene PCO transformation products, such as benzene and formaldehyde, in the outflow of both permeate and retentate compartments was proposed. The influence of operating parameters on the process, i.e., light intensity, pressure, membrane type, and catalyst mass, was also studied. The results reveal that membrane separation-PCO hybridization is particularly effective for reducing the presence of benzene and formaldehyde in the effluent treated. The benzene concentration in the outflow of the hybrid module can be reduced by a factor of 120 compared to that observed during the PCO of toluene alone.
RESUMEN
The data contained in this publication refers to a new approach to design composite pervaporation membranes that could be useful in water treatment. The work is based on the rational prediction of the membrane mass transfer coefficient using the resistance in series model and the corresponding experimental membranes were tested with several aqueous solutions comparatively to a commercially available porous distillation membrane (PVDF). All the related data, i.e. permeation water fluxes and conductivity of the permeate, were collected for hours, in the range 3 to 7 h. The strategy was to develop pervaporation membranes by coating a porous PVDF support (122µm) with various dense layers (hydrophobic polymers: Teflon™ AF2400, PMP, PTMSP). The objective was to avoid definitely the wetting problem observed in membrane distillation while keeping approximately the permeance than the porous support. The data reported here are related to the surface property of the membranes (contact angles), to the mechanical resistance of the membranes, to the wetting phenomena observed directly and recorded by observing the variation of water flux through the membranes and to the conductivity of the water condensed at the permeate side.
RESUMEN
The article describes data concerning the separation performances of polymeric hollow-fiber membranes. The data were obtained using a model for simulating gas separation, described in the research article entitled "Interplay of inlet temperature and humidity on energy penalty for CO2 post-combustion capture: rigorous analysis and simulation of a single stage gas permeation process" (L. Giordano, D. Roizard, R. Bounaceur, E. Favre, 2016) [1]. The data were used to validate the model by comparison with literature results. Considering a membrane system based on feed compression only, data from the model proposed and that from literature were compared with respect to the molar composition of permeate stream, the membrane area and specific energy requirement, varying the feed pressure and the CO2 separation degree.
RESUMEN
The flow structuration of silicon oil (Prandtl number of 10.3) in a open cylindrical pool heated from the center of the surface is investigated numerically. Our purpose is to perform the numerical simulation of experimental results obtained by Favre [Phys. Fluids 9, 1473 (1997)] who observed transitions between steady and axisymmetric flows at sufficiently low values of the Marangoni number (Ma) and various types of instability depending on the height of the fluid. The hydrothermal wave regime has been obtained at critical values of Ma which depend on the Bond number and on the aspect ratio. The numerical results are in good agreement with the experimental ones.