RESUMEN
Na3Sc2-xRx(PO4)3 (R = Eu, Tb, Dy; 0 ≤ x ≤ 0.2) phosphors were synthesized by a high-temperature solid-state reaction. Sc : R ratios for the NSP:xR samples were determined by ICP-MS, EDX-SEM and TEM-EDX measurements. An X-ray diffraction study revealed that solid solutions with a NASICON-type structure were formed at 0 ≤ x ≤ 0.1. The luminescence properties of Na3Sc2(PO4)3 and Na3Sc2-xRx(PO4)3 (R = Eu, Tb, Dy) were studied in the range of 80-500 K. The highest R3+ luminescence intensity in Na3Sc2-xRx(PO4)3 (R = Eu, Tb, Dy) depending on R was found for x = 0.05 in the case of Dy and x = 0.1 in the case of Eu and Tb. The temperature behaviour of the R3+ emission intensity of Na3Sc2-xRx(PO4)3 (R = Eu, Tb, Dy) depends on R that replaces Sc. The decrease of the Eu3+ emission intensity depending on the transition energy by â¼26% and 18% at â¼420 K compared to TR allowed us to consider NSP:0.1Eu3+ as a suitable phosphor for pc-LEDs. The temperature dependence of the Dy3+ emission for NSP:0.05Dy3+ demonstrates a strong thermal quenching. Different temperature dependences of the Tb3+ emission intensity of NSP:0.1Tb3+ were found for two excitation bands at λex = 220 and 378 nm representing f-d and f-f intracentre transitions. No thermal quenching for f-f transitions takes place while the emission intensity for f-d transitions increases with a temperature rise from 80 to 500 K. The dielectric measurements for Na3Sc2(PO4)3 and Na3Sc1.9Eu0.1(PO4)3 were provided on ceramic pellets sintered under vacuum using a spark plasma sintering technique. Different dependences of conductivity were found for two samples. The calculated conductivity for Na3Sc1.9Eu0.1(PO4)3 with an R3Ìc structure (σbulk = 6.4 × 10-5 S cm-1 at 300 K, 1.14 × 10-3 S cm-1 at 360 K and 5.0 × 10-2 S cm-1 at 500 K) is higher than that for pure α-Na3Sc2(PO4)3 but lower than that for ß- and γ-Na3Sc2(PO4)3.
RESUMEN
This paper describes the potential of high-resolution continuum source graphite furnace atomic absorption spectrometry for determination of Pt, Pd and Rh after separation and concentration by original in-house developed heterochain polymer S, N-containing sorbent. The methods of sample preparation of spent ceramic-based autocatalysts were considered, two of which were used: autoclave decomposition in mixture of acids HCl:HNO3 (3:1) and high-temperature melting with K2S2O7. Both methods anyway limit the direct determination of analytes by HR CS GFAAS. Using the first method it is an incomplete digestion of spent autocatalysts samples, since the precipitate is Si, and the rhodium metal dissolves with difficulty and partially passes into solution. In contrast to the first method, the second method allow to completely transfer analytes into solution, however, the background signal produced by the chemical composition of the flux, overlaps the analytical zone. It was found, that Pt, Pd and Rh contained in the spent ceramic automotive catalysts could be effectively separated and concentrated by heterochain polymer S, N-containing sorbent, which has high sorption capacity, selectivity and resistant to dilute acids. The chosen HR CS GFAAS analysis conditions enable us to determine Pt, Pd and Rh with good metrological characteristics. The concentrations of Pt, Pd and Rh in two samples of automobile exhaust catalysts were found in range of 0.00015-0.00050; 0.170-0.189; 0.0180-0.0210wt%, respectively. The relative standard deviation obtained by HR CS GFAAS was not more than 5%. Limits of detection by HR CS GFAAS achieved were 6.2·10(-6)wt% for Pt, 1.8·10(-6)wt% for Pd, and 3.4·10(-6)wt% for Rh. Limits of determination achieved by HR CS GFAAS were 1.1·10(-5)wt% for Pt, 6.9·10(-5)wt% for Pd, and 8.3·10(-5)wt% for Rh. To control the accuracy of PGM in sorption concentrates by HR CS GFAAS method, it was appropriate to conduct an inter-method comparative experiment. The researches on the application of atomic-emission spectroscopy method with inductively coupled plasma as a comparative method were conducted. In addition, the trueness control of the obtained results is confirmed by added-found method.