[Comparison of adhesive seal morphology between APC™ PLUS and APC™ Flash-Free Adhesive Coated brackets]. / Comparaison du joint de colle entre les attaches préencollées APC™ PLUS et les attaches APC™ Flash-Free.

INTRODUCTION: Does the new adhesive-coated APC™ Flash-Free bracket from the 3M Unitek® group simplify the bonding protocol without compromising precision? OBJECTIVES: The aim of this study was to compare the morphology of the adhesive joint between the classic APC™ PLUS adhesive-coated brackets and APC™ Flash-Free brackets. MATERIALS AND METHODS: In vitro bonding of esthetic brackets in the CLARITY™ ADVANCED range was performed to compare the morphology of the excess flash between APC™ PLUS and APC™ Flash-Free brackets. RESULTS: No statistically significant difference was found concerning the morphology of the excess flash between APC™ PLUS and APC™ Flash-Free brackets. A statistically significant difference was found regarding the thickness of the adhesive between the two types of bracket. The adhesive used for the APC™ Flash-Free brackets was significantly thicker than for the APC™ PLUS brackets (P=0.0001). Adhesive thickness was also more homogeneous on the APC™ Flash-Free brackets (P=0.001 for the relative difference). CONCLUSION: The adhesive is thicker but adhesive homogeneity is greater with APC™ Flash-Free brackets than with APC™ PLUS brackets.

[Is the shape memory effect a reality for 35° Copper Ni-Ti(®)? Study by means of differential scanning calorimetry]. / L'effet mémoire de forme est-il une réalité clinique pour le 35° Copper Ni-Ti(®) ? Étude par calorimétrie différentielle à balayage.

INTRODUCTION: Copper-nickel-titanium alloys are supposed to deliver a shape memory effect: when they are brought to a low temperature phase and subjected to a plastic deformation, they should recover their initial shape by simple heating. Nickel-titanium alloys can display different crystallographic phases: martensite, austenite and an inconstant intermediate R-phase. The shape memory effect is generally associated with the transition from martensite to austenite but it could also accompany the transition from R-phase to austenite. Since oral temperatures are not compatible with a fully martensitic alloy, this study aims, for 35° Copper Ni-Ti(®), to assess the R-phase presence at oral temperatures and to verify the possibility of using the R-phase shape memory effect under clinical conditions. MATERIALS AND METHODS: Thirty consecutive 35° Copper Ni-Ti(®) archwires from two different batches were examined by differential scanning calorimetry with partial cycles limited to temperatures encountered within the oral cavity (from 0 °C to 50 °C). The presence of an intermediate crystallographic phase was assessed on the thermograms. The transformation temperatures were determined and the two batches were compared using the Mann-Whitney U Test. RESULTS: Upon heating, all wires transformed directly from martensite to austenite. Af (mean  = 33.5 °C, SD  = 0.8 °C) was generally below the temperature stated by the manufacturer and a statistically significant difference (p ≤ 0.01) was found between the two batches. CONCLUSIONS: No R-phase was detected and transformation temperatures were not constant. This study questions the supposed shape memory effect displayed by 35° Copper Ni-Ti(®) wires under clinical conditions.

Torsional superelasticity of NiTi archwires.

OBJECTIVE: To reproduce and compare the intraoral torsional behavior of 10 commonly used preformed upper NiTi 0.017 x 0.025 archwires in 0.018-slot brackets at 20 degrees C, 35 degrees C, and 55 degrees C. MATERIALS AND METHODS: Ten upper preformed NiTi archwires were compared to a multibraided stainless steel wire. An original testing bench was used to reproduce palatal root torque applied onto an upper central incisor with a maximum value of 1540 g x mm. Ten samples of each wire type were tested at 20 degrees C, 35 degrees C, and 55 degrees C each. RESULTS: Loading and unloading at 20 degrees C revealed three categories of wires: a group of four NiTi wires of relative stiffness bereft of any superelasticity, a group of six NiTi wires displaying some horizontal plateau, and finally the stainless steel wire of lesser stiffness. Testing at the average oral temperature of 35 degrees C produced the same three categories of wires, with only 2 of 10 NiTi wires displaying a superelastic effect (Copper NiTi 35 degrees C and 40 degrees C). None of the NiTi wires was superelastic at 55 degrees C. Moments increased with temperature as the martensite was replaced by the more rigid austenite. CONCLUSION: This study showed that most NiTi wires did not exhibit in torsion the superelastic effect traditionally described in bending. The combination of straight-wire prescriptions and rectangular superelastic NiTi archwires did not provide optimal constant moments necessary to gain third-order control of tooth movement early in treatment. A braided stainless steel rectangular archwire displayed better torsional behavior at 35 degrees C than most NiTi archwires of the same dimensions.