Boosting the Reactivity of Bis-Lactones to Enable Step-Growth Polymerization at Room Temperature.

The development of new sustainable polymeric materials endowed with improved performances but minimal environmental impact is a major concern, with polyesters as primary targets. Lactones are key monomers thanks to ring-opening polymerization, but their use in step-growth polymerization has remained scarce and challenging. Herein, we report a powerful bis(γ-lactone) (γSL) that was efficiently prepared on a gram scale from malonic acid by Pd-catalyzed cycloisomerization. The γ-exomethylene moieties and the spiro structure greatly enhance its reactivity toward ring-opening and enable step-growth polymerization under mild conditions. Using diols, dithiols, or diamines as comonomers, a variety of regioregular (AB)n copolymers with diverse linkages and functional groups (from oxo-ester to ß-thioether lactone and ß-hydroxy-lactame) have been readily prepared. Reaction modeling and monitoring revealed the occurrence of an original trans-lactonization process following the first ring-opening of γSL. This peculiar reactivity opens the way to regioregular (ABAC)n terpolymers, as illustrated by the successive step-growth polymerization of γSL with a diol and a diamine.

Degradable Alternating Copolymers by Radical Copolymerization of 2-Methylen-1,3-dioxepane and Crotonate Esters.

Producing backbone degradable copolymers via free-radical copolymerization is a promising, yet challenging method to develop more sustainable materials for many applications. In this work, we present the copolymerization of 2-methylen-1,3-dioxepane (MDO) with crotonic acid derivative esters. MDO can copolymerize by radical ring-opening polymerization incorporating degradable ester moieties in the polymer backbone, although this can often be difficult due to the very unfavorable reactivity ratios. Crotonic acid derivatives, on the other hand, can be easily produced completely from biomass but are typically very difficult to (co)polymerize due to low propagation rates and very unfavorable reactivity ratios. Herein, we present the surprisingly easy copolymerization between MDO and butyl crotonate (BCr), which shows the ability to form alternating copolymers. The alternating nature of the copolymer was characterized by MALDI-TOF and supported by the reactivity ratios calculated experimentally (rMDO = 0.105 and rBCr = 0.017). The alternating nature of the copolymers favored the degradability that could be achieved under basic conditions (in 2 h, all chains have molar masses smaller than 2 kg/mol). Last, the work was expanded to other crotonate monomers to expand the portfolio and show the potential of this copolymer family.

A Single Amino Acid Able to Promote High-Temperature Ring-Opening Polymerization by Dual Activation.

Amino acids are indispensable compounds in the body, performing several biological processes that enable proper functioning. In this work, it is demonstrated that a single amino acid, taurine, is also able to promote the ring-opening polymerization (ROP) of several cyclic monomers under industrially relevant conditions. It is shown that the unique zwitterionic structure of taurine, where the negatively charged sulfonic acid group and the protonated amine group are separated by two methylene groups, not only provides high thermal stability but also leads to a dual activation mechanism, which is corroborated by quantum mechanical calculations. This unique mechanism allows for the synthesis of polylactide of up to 50 kDa in bulk at 180 °C with good end-group fidelity using a highly abundant catalyst. Furthermore, cytotoxicity tests confirm that PLLA synthesized with taurine is non-toxic. Moreover, it is demonstrated that the presence of taurine does not have any detrimental effect on the thermal stability of polylactide, and therefore polymers can be used directly without any post-polymerization purification. It is believed that the demonstration that a simple structure composed of a single amino acid can promote polymerization can bring a paradigm shift in the preparation of polymers.

Semiconducting Polymer Nanoporous Thin Films as a Tool to Regulate Intracellular ROS Balance in Endothelial Cells.

The design of soft and nanometer-scale photoelectrodes able to stimulate and promote the intracellular concentration of reactive oxygen species (ROS) is searched for redox medicine applications. In this work, we show semiconducting polymer porous thin films with an enhanced photoelectrochemical generation of ROS in human umbilical vein endothelial cells (HUVECs). To achieve that aim, we synthesized graft copolymers, made of poly(3-hexylthiophene) (P3HT) and degradable poly(lactic acid) (PLA) segments, P3HT-g-PLA. In a second step, the hydrolysis of sacrificial PLA leads to nanometer-scale porous P3HT thin films. The pore sizes in the nm regime (220-1200 nm) were controlled by the copolymer composition and the structural arrangement of the copolymers during the film formation, as determined by atomic force microscopy (AFM) and transmission electron microscopy (TEM). The porous P3HT thin films showed enhanced photofaradaic behavior, generating a higher concentration of ROS in comparison to non-porous P3HT films, as determined by scanning electrochemical microscopy (SECM) measurements. The exogenous ROS production was able to modulate the intracellular ROS concentration in HUVECs at non-toxic levels, thus affecting the physiological functions of cells. Results presented in this work provide an important step forward in the development of new tools for precise, on-demand, and non-invasive modulation of intracellular ROS species and may be potentially extended to many other physiological or pathological cell models.

Polyether Single and Double Crystalline Blends and the Effect of Lithium Salt on Their Crystallinity and Ionic Conductivity.

In this work, blends of Poly(ethylene oxide), PEO, and poly(1,6-hexanediol), PHD, were prepared in a wide composition range. They were examined by Differential Scanning Calorimetry (DSC), Polarized Light Optical Microscopy (PLOM) and Wide Angle X-ray Scattering (WAXS). Based on the results obtained, the blends were partially miscible in the melt and their crystallization was a function of miscibility and composition. Crystallization triggered phase separation. In blends with higher PEO contents both phases were able to crystallize due to the limited miscibility in this composition range. On the other hand, the blends with higher PHD contents display higher miscibility and therefore, only the PHD phase could crystallize in them. A nucleation effect of the PHD phase on the PEO phase was detected, probably caused by a transference of impurities mechanism. Since PEO is widely used as electrolyte in lithium batteries, the PEO/PHD blends were studied with lithium bis(trifluoromethanesulfonyl) imide (LiTFSI), and the effect of Li-salt concentration was studied. We found that the lithium salt preferentially dissolves in the PEO phase without significantly affecting the PHD component. While the Li-salt reduced the spherulite growth rate of the PEO phase within the blends, the overall crystallization rate was enhanced because of the strong nucleating effect of the PHD component. The ionic conductivity was also determined for the blends with Li-salt. At high temperatures (>70 °C), the conductivity is in the order of ~10-3 S cm-1, and as the temperature decreases, the crystallization of PHD was detected. This improved the self-standing character of the blend films at high temperatures as compared to the one of neat PEO.

3D Printable Conducting and Biocompatible PEDOT-graft-PLA Copolymers by Direct Ink Writing.

Tailor-made polymers are needed to fully exploit the possibilities of additive manufacturing, constructing complex, and functional devices in areas such as bioelectronics. In this paper, the synthesis of a conducting and biocompatible graft copolymer which can be 3D printed using direct melting extrusion methods is shown. For this purpose, graft copolymers composed by conducting polymer poly(3,4-ethylenedioxythiophene) (PEDOT) and a biocompatible polymer polylactide (PLA) are designed. The PEDOT-g-PLA copolymers are synthesized by chemical oxidative polymerization between 3,4-ethylenedioxythiophene and PLA macromonomers. PEDOT-g-PLA copolymers with different compositions are obtained and fully characterized. The rheological characterization indicates that copolymers containing below 20 wt% of PEDOT show the right complex viscosity values suitable for direct ink writing (DIW). The 3D printing tests using the DIW methodology allows printing different parts with different shapes with high resolution (200 µm). The conductive and biocompatible printed patterns of PEDOT-g-PLA show excellent cell growth and maturation of neonatal cardiac myocytes cocultured with fibroblasts.

Stereoretention in the Bulk ROP of l-Lactide Guided by a Thermally Stable Organocatalyst.

Polylactide (PLA) has emerged as one of the most promising bio-based alternatives to petroleum-based plastics, mainly because it can be produced from the fermentation of naturally occurring sugars and because it can be industrially compostable. In spite of these benefits, the industrial ring-opening polymerization (ROP) of l-lactide (L-LA) still requires the use of highly active and thermally stable metal-based catalysts, which have raised some environmental concerns. While the excellent balance between activity and functional group compatibility of organic acid catalysts makes them some of the most suitable catalysts for the metal-free ROP of L-LA, the majority of these acids are highly volatile and subject to decomposition at high temperature, which limits their use under industrially relevant conditions. In this work we exploit the use of a nonstoichiometric acid-base organocatalyst to promote the solvent-free and metal-free ROP of L-LA at elevated temperatures in the absence of epimerization and transesterification. To do so, a stable acidic complex was prepared by mixing 4-(dimethylamino)pyridine (DMAP) with 2 equiv of methanesulfonic acid (MSA). Both experimental and computational results indicate that DMAP:MSA (1:2) not only is highly thermally stable but also promotes the retention of stereoregularity during the polymerization of L-LA, leading to PLLA with a molar mass of up to 40 kg mol-1 and a chiral purity in excess of 98%. This result provides a new feature to exploit in organocatalyzed polymerization and in the design of new catalysts to facilitate the path to market.