Setting occupational exposure limits for antimicrobial agents: A case study based on a quaternary ammonium compound-based disinfectant.

Antimicrobial agents have become an essential tool in controlling the transmission of severe acute respiratory syndrome coronavirus 2 (SARS-CoV-2), and guidelines on their use have been issued by various public health agencies. Through its Emerging Viral Pathogen Guidance for Antimicrobial Pesticides, the US Environmental Protection Agency has approved numerous surface disinfectant products for use against SARS-CoV-2. Despite their widespread use and range of associated health hazards, the majority of active ingredients in antimicrobial products, such as surface disinfectants, lack established occupational exposure limits (OELs) to assist occupational health professionals in characterizing risks from exposures to these chemicals. Based on established approaches from various organizations, a framework for deriving OELs specific to antimicrobial agents was developed that relies on a weight-of-evidence evaluation of the available data. This framework involves (1) a screening-level toxicological assessment based on a review of the existing literature and recommendations, (2) identification of the critical adverse effect(s) and dose-response relationship(s), (3) identification of alternative health-based exposure limits (HBELs), (4) derivation of potential OELs based on identified points of departure and uncertainty factors and/or modification of existing alternative HBELs, and (5) selection of an appropriate OEL. To demonstrate the use of this framework, a case study is described for selection of an OEL for a disinfectant product containing quaternary ammonium compounds (quats). Three potential OELs were derived for this product based on irritation toxicity data, developmental and reproductive toxicity (DART) data, and modification of an existing HBEL. The final selected OEL for the quats-containing product was 0.1 mg/m3, derived from modification of an existing HBEL. This value represented the lowest resulting value of the three approaches, and thus, was considered protective of irritation and potential DART.

An updated evaluation of potential health hazards associated with exposures to asbestos-containing drywall accessory products.

Following a previously published (2012) evaluation of the potential health hazards related to the use of asbestos-containing drywall accessory products, additional information regarding asbestos exposures during the use of accessory products, as well as studies of chrysotile asbestos risk as a function of exposure, have been published in the peer-reviewed literature. The purpose of this analysis is to update the original evaluation with this new information. It was previously estimated that a professional drywaller performing joint compound-associated tasks could have a lifetime cumulative chrysotile exposure of 12-26 f/cc-year. Using conservative assumptions regarding airborne asbestos levels during different drywalling tasks, task duration, and job tenure, we found that a range of 4.3-36.3 f/cc-year is a plausible estimate of a career drywaller's cumulative asbestos exposure from historical joint compound use. The estimated range for bystander exposures would be below (sometimes significantly below) this range depending on the frequency and duration of work near drywallers. Further, the estimated drywaller and bystander total fiber exposures were well below a recently published "no-observed adverse effect level, best estimate" for predominately chrysotile exposures of 89-168 f/cc-year for lung cancer and 208-415 f/cc-year for mesothelioma. We also determined that, even if the chrysotile or possibly talc ingredients in the drywall products had contained asbestiform tremolite, the cumulative tremolite exposures would have been well below a recently published tremolite no-effect level of 0.5-2.6 f/cc-year. Based on our calculations, typical drywall work using asbestos-containing drywall accessory products is not expected to increase the risk of asbestos-related lung cancer or mesothelioma. These conclusions are consistent with the lack of epidemiological evidence that drywall work resulted in an increased incidence of asbestos-related disease in the drywall trades.

Derivation of an occupational exposure limit for diacetyl using dose-response data from a chronic animal inhalation exposure study.

Occupational exposure limits (OELs) have been previously proposed for diacetyl; however, most of these values are based on worker cohort studies that are known to have several limitations and confounders. In this analysis, an 8 hour time-weighted average (TWA) OEL for diacetyl was derived based on data from a chronic, 2 year animal inhalation study recently released by the US National Toxicology Program. In that study, complete histopathology was conducted on male and female mice and rats exposed to 0, 12.5, 25 or 50 ppm diacetyl. Several responses in the lower respiratory tract of rats (the more sensitive species) were chosen as the critical endpoints of interest. Benchmark concentration (BMC) modeling of these endpoints was used to estimate BMC values associated with a 10% extra risk (BMC10 ) and the associated 95% lower confidence bound (BMCL10 ), which were subsequently converted to human equivalent concentrations (HECs) using a computational fluid dynamics-physiologically based pharmacokinetic (CFD-PBPK) model to account for interspecies dosimetry differences. A composite uncertainty factor of 8.0 was applied to the human equivalent concentration values to yield 8 hour TWA OEL values with a range of 0.16-0.70 ppm. The recommended 8 hour TWA OEL for diacetyl vapor of 0.2 ppm, based on minimal severity of bronchiolar epithelial hyperplasia in the rat, is practical and health-protective.

Ambient Asbestos Fiber Concentrations and Long-Term Trends in Pleural Mesothelioma Incidence between Urban and Rural Areas in the United States (1973-2012).

Over the past 40 years, measured ambient asbestos concentrations in the United States have been higher in urban versus rural areas. The purpose of this study was to determine whether variations in ambient asbestos concentrations have influenced pleural mesothelioma risk in females (who generally lacked historic occupational asbestos exposure relative to males). Male pleural mesothelioma incidence trends were analyzed to provide perspective for female trends. Annual age-adjusted incidence rates from 1973 to 2012 were obtained from the SEER 9, 13, and 18 databases for urban and rural locations, and standardized rate ratios were calculated. Female rural rates exceeded urban rates in almost half of the years analyzed, although the increases were not statistically significant, which is in line with expectations if there was no observable increased risk for urban locations. In contrast, male urban rates were elevated over rural rates for nearly all years examined and were statistically significantly elevated for 22 of the 40 years. Trend analyses demonstrated that trends for females remained relatively constant over time, whereas male urban and rural incidence increased into the 1980s and 1990s, followed by a decrease/leveling off. Annual female urban and rural incidence rates remained approximately five- to six-fold lower than male urban and rural incidence rates on average, consistent with the comparatively increased historical occupational asbestos exposure for males. The results suggest that differences in ambient asbestos concentrations, which have been reported to be 10-fold or greater across regions in the United States, have not influenced the risk of pleural mesothelioma.

Evaluation of the presence of asbestos in cosmetic talcum products.

Talc has been used for over a century in a variety of cosmetic products. While pure cosmetic talc (free of asbestos) is not considered a risk factor for mesothelioma, it has been recently suggested that inhalation of cosmetic talc containing trace levels of asbestos is a risk factor for mesothelioma. Bulk analyses of cosmetic talcum products were performed in the 1960s and 1970s, however, the analytical methods used at that time were incapable of determining whether asbestos minerals were present in the asbestiform versus non-asbestiform habit. The distinction between these two mineral habits is critical, as non-asbestiform amphibole minerals do not present an asbestos-related cancer risk via inhalation. As such, we evaluated six historical talcum powders using modern-era analytical methods to determine if asbestos is present, and if so, to identify the mineral habit (asbestiform versus non-asbestiform) of the asbestos. Based on their labels, the products were produced by four manufacturers and sold between 1940 and 1977. The products were analyzed in duplicate by two laboratories using standard protocols. Laboratory A analyzed samples using X-ray diffraction (XRD) and polarized light microscopy (PLM), and Laboratory B analyzed samples using PLM and transmission electron microscopy (TEM) with energy dispersive X-ray analysis (EDX) and selected area electron diffraction (SAED). No asbestiform minerals were found in any of the products. Nonetheless, even if some historical cosmetic talcum products contained trace amounts (≤0.1%) of asbestiform minerals, any resulting asbestos exposure would be expected to be exceedingly low, and comparable to exposures from breathing ambient air.

Supplementary dataset for child and adult exposure and health risk evaluation following the use of metal- and metalloid-containing costume cosmetics sold in the United States.

The data presented in this article are related to the research article entitled "Child and adult exposure and health risk evaluation following the use of metal- and metalloid-containing costume cosmetics sold in the United States" [1]. This article describes the concentration of metals and metalloids contained in various cosmetic products such as body paint, lipstick and eye shadow, the relative percent deviation of two analyses performed on the products and the physico-chemico properties of the metals and metalloids used in the SkinPerm model presented in the aforementioned article.

Combined analysis of job and task benzene air exposures among workers at four US refinery operations.

Workplace air samples analyzed for benzene at four US refineries from 1976 to 2007 were pooled into a single dataset to characterize similarities and differences between job titles, tasks and refineries, and to provide a robust dataset for exposure reconstruction. Approximately 12,000 non-task (>180 min) personal samples associated with 50 job titles and 4000 task (<180 min) samples characterizing 24 tasks were evaluated. Personal air sample data from four individual refineries were pooled based on a number of factors including (1) the consistent sampling approach used by refinery industrial hygienists over time, (2) the use of similar exposure controls, (3) the comparability of benzene content of process streams and end products, (4) the ability to assign uniform job titles and task codes across all four refineries, and (5) our analysis of variance (ANOVA) of the distribution of benzene air concentrations for select jobs/tasks across all four refineries. The jobs and tasks most frequently sampled included those with highest potential contact with refinery product streams containing benzene, which reflected the targeted sampling approach utilized by the facility industrial hygienists. Task and non-task data were analyzed to identify and account for significant differences within job-area, task-job, and task-area categories. This analysis demonstrated that in general, areas with benzene containing process streams were associated with greater benzene air concentrations compared to areas with process streams containing little to no benzene. For several job titles and tasks analyzed, there was a statistically significant decrease in benzene air concentration after 1990. This study provides a job and task-focused analysis of occupational exposure to benzene during refinery operations, and it should be useful for reconstructing refinery workers' exposures to benzene over the past 30 years.

Anthophyllite asbestos: state of the science review.

Anthophyllite is an amphibole form of asbestos historically used in only a limited number of products. No published resource currently exists that offers a complete overview of anthophyllite toxicity or of its effects on exposed human populations. We performed a review focusing on how anthophyllite toxicity was understood over time by conducting a comprehensive search of publicly available documents that discussed the use, mining, properties, toxicity, exposure and potential health effects of anthophyllite. Over 200 documents were identified; 114 contained relevant and useful information which we present chronologically in this assessment. Our analysis confirms that anthophyllite toxicity has not been well studied compared to other asbestos types. We found that toxicology studies in animals from the 1970s onward have indicated that, at sufficient doses, anthophyllite can cause asbestosis, lung cancer and mesothelioma. Studies of Finnish anthophyllite miners, conducted in the 1970s, found an increased incidence of asbestosis and lung cancer, but not mesothelioma. Not until the mid-1990s was an epidemiological link with mesothelioma in humans observed. Its presence in talc has been of recent significance in relation to potential asbestos exposure through the use of talc-containing products. Characterizing the health risks of anthophyllite is difficult, and distinguishing between its asbestiform and non-asbestiform mineral form is essential from both a toxicological and regulatory perspective. Anthophyllite toxicity has generally been assumed to be similar to other amphiboles from a regulatory standpoint, but some notable exceptions exist. In order to reach a more clear understanding of anthophyllite toxicity, significant additional study is needed. Copyright © 2016 John Wiley & Sons, Ltd.

Child and adult exposure and health risk evaluation following the use of metal- and metalloid-containing costume cosmetics sold in the United States.

Costume cosmetics (lipstick, body paints, eyeshadow) were analyzed for metals using inductively coupled plasma mass spectrometry (ICP-MS). Sb was detected in all samples (range: 0.12-6.3 mg/kg; d.f. 100%), followed by Pb (<0.15-9.3 mg/kg), Ni (<0.20-6.3 mg/kg), Co (<0.5-2.0 mg/kg); with d.f. 80% each, Hg (<0.00015-0.0020 mg/kg; d.f. 50%) and As (0.53 mg/kg, d.f. 10%). Ingestion and dermal exposures were estimated for child- and adult-intermittent and adult-occupational users. Adult-occupational users exceeded the U.S. EPA Reference Dose (RfD) for Sb and the CA Proposition 65 maximum allowable dose level (MADL) for Pb was exceeded for all user scenarios. The Pb dose from body paint was sufficient to raise blood lead levels (BLL) in all user scenarios above baseline BLLs from 0.2 µg/dL to 1.9 µg/dL per the Adult Lead Model (ALM) and child Integrated Exposure Uptake Biokinetic (IEUBK) blood Pb models. Change in BLL was less than 1 µg/dL amongst the child and adult-intermittent users, the benchmark change in BLL developed for health risk assessments for children. Adult-occupational users exceeded the CA Proposition 65 NSRL intake value of 15 µg/day, which corresponds to an increase of 1.2 µg/dL above baseline levels using ALM. Exposure of occupational users of costume cosmetics should be evaluated further to prevent unnecessary metal exposure.

Naturally occurring diacetyl and 2,3-pentanedione concentrations associated with roasting and grinding unflavored coffee beans in a commercial setting.

Over the last decade, concerns have been raised about potential respiratory health effects associated with occupational exposure to the flavoring additives diacetyl and 2,3-pentanedione. Both of these diketones are also natural components of many foods and beverages, including roasted coffee. To date, there are no published studies characterizing workplace exposures to these diketones during commercial roasting and grinding of unflavored coffee beans. In this study, we measured naturally occurring diacetyl, 2,3-pentanedione, and respirable dust at a facility that roasts and grinds coffee beans with no added flavoring agents. Sampling was conducted over the course of three roasting batches and three grinding batches at varying distances from a commercial roaster and grinder. The three batches consisted of lightly roasted soft beans, lightly roasted hard beans, and dark roasted hard beans. Roasting occurred for 37 to 41 min, and the grinding process took between 8 and 11 min. Diacetyl, 2,3-pentanedione, and respirable dust concentrations measured during roasting ranged from less than the limit of detection (

An independent evaluation of plutonium body burdens in populations near Los Alamos Laboratory using human autopsy data.

In the mid-1940s, the United States began producing atomic weapon components at the Los Alamos National Laboratory (LANL). In an attempt to better understand historical exposure to nearby residents, this study evaluates plutonium activity in human tissue relative to residential location and length of time at residence. Data on plutonium activity in the lung, vertebrae, and liver of nearby residents were obtained during autopsies as a part of the Los Alamos Tissue Program. Participant residential histories and the distance from each residence to the primary plutonium processing buildings at LANL were evaluated in the analysis. Summary statistics, including Student t-tests and simple regressions, were calculated. Because the biological half-life of plutonium can vary significantly by organ, data were analyzed separately by tissue type (lung, liver, vertebrae). The ratios of plutonium activity (vertebrae:liver; liver:lung) were also analyzed in order to evaluate the importance of timing of exposure. Tissue data were available for 236 participants who lived in a total of 809 locations, of which 677 were verified postal addresses. Residents of Los Alamos were found to have higher plutonium activities in the lung than non-residents. Further, those who moved to Los Alamos before 1955 had higher lung activities than those who moved there later. These trends were not observed with the liver, vertebrae, or vertebrae:liver and liver:lung ratio data, however, and should be interpreted with caution. Although there are many limitations to this study, including the amount of available data and the analytical methods used to analyze the tissue, the overall results indicate that residence (defined as the year that the individual moved to Los Alamos) may have had a strong correlation to plutonium activity in human tissue. This study is the first to present the results of Los Alamos Autopsy Program in relation to residential status and location in Los Alamos.

Dose-response relationships for blood cobalt concentrations and health effects: a review of the literature and application of a biokinetic model.

Cobalt (Co) is an essential component of vitamin B(12). As with all metals, at sufficiently high doses, Co may exert detrimental effects on different organ systems, and adverse responses have been observed in animals, patients undergoing Co therapy, and workers exposed to respirable Co particulates. Although blood Co concentrations are postulated to be the most accurate indicator of ongoing Co exposure, little is known regarding the dose-response relationships between blood Co concentrations and adverse health effects in various organ systems. In this analysis, the animal toxicology and epidemiology literature were evaluated to identify blood Co concentrations at which effects have, and have not, been reported. Where necessary, a biokinetic model was used to convert oral doses to blood Co concentrations. Our results indicated that blood Co concentrations of 300 µg/L and less have not been associated with adverse responses of any type in humans. Concentrations of 300 µg/L and higher were associated with certain hematological and reversible endocrine responses, including polycythemia and reduced iodide uptake. Blood Co concentrations of 700-800 µg Co/L and higher may pose a risk of more serious neurological, reproductive, or cardiac effects. These blood concentrations should be useful to clinicians and toxicologists who are attempting to interpret blood Co concentrations in exposed individuals.

Derivation of a chronic oral reference dose for cobalt.

Cobalt (Co) is an essential element in humans as a component of vitamin B12. However, at high levels Co exposure has been shown to have detrimental effects. This study was designed to identify a chronic oral reference dose (RfD) for Co. Currently available data indicate that non-cancer health effects associated with Co exposure may include hematological, neurological, immunological, reproductive, cardiovascular, and endocrine responses. This analysis employs the standard US EPA risk assessment methodology for establishing a chronic RfD. In this analysis, the Jaimet and Thode (1955) 10-week, multiple dose human study of thyroid effects (decreased iodine uptake) in children was determined to be the most robust and sensitive study for identifying a potential point of departure dose (POD). A dose of 0.9 mgCo/kg-day was chosen as the POD. Consistent with the US EPA's previous derivation of the perchlorate RfD, which is also based on decreased iodine uptake in humans, we considered several uncertainly factors (UFs), and determined that a factor of 10 for human variability was appropriate, as well as a factor of three for database adequacy. Applying an aggregate uncertainty factor of 30 to the POD yields a chronic oral RfD of 0.03 mg/kg-day. We believe this value would be protective of non-cancer health effects in the general population for a lifetime of daily exposure to Co.

Inorganic cobalt supplementation: prediction of cobalt levels in whole blood and urine using a biokinetic model.

Soluble cobalt (Co) supplements with recommended daily doses up to 1000 µg Co/day are increasingly being marketed to consumers interested in healthy living practices. For example, some athletes may consider using Co supplements as blood doping agents, as Co is known to stimulate erythropoesis. However, the distribution and excretion kinetics of ingested Co are understood in a limited fashion. We used a Co-specific biokinetic model to estimate whole blood and urine Co levels resulting from oral exposure or ingestion of Co in amounts exceeding typical dietary intake rates. Following 10 days of Co supplementation at a rate of 400 to 1000 µg/day, predicted adult Co concentrations range from 1.7 to 10 µg/L in whole blood, and from 20 to 120 µg/L in urine. Chronic supplementation (≥ 1 year) at a rate of 1000 µg Co/day is predicted to result in blood levels of 5.7 to 13 µg/L, and in urine levels from 65 to 150 µg/L. The model predictions are within those measured in humans following ingestion of known doses. The methodology presented in this paper can be used to predict urinary or blood Co levels following acute or chronic occupational incidental ingestion, medicinal therapy, supplemental intake, or other non-occupational exposures.

Airborne concentrations of metals and total dust during solid catalyst loading and unloading operations at a petroleum refinery.

Workers handle catalysts extensively at petroleum refineries throughout the world each year; however, little information is available regarding the airborne concentrations and plausible exposures during this type of work. In this paper, we evaluated the airborne concentrations of 15 metals and total dust generated during solid catalyst loading and unloading operations at one of the largest petroleum refineries in the world using historical industrial hygiene samples collected between 1989 and 2006. The total dust and metals, which included aluminum, cadmium, chromium, cobalt, copper, iron, lead, manganese, molybdenum, nickel, platinum, silicon, silver, vanadium, and zinc, were evaluated in relation to the handling of four different types of solid catalysts associated with three major types of catalytic processes. Consideration was given to the known components of the solid catalysts and any metals that were likely deposited onto them during use. A total of 180 analytical results were included in this analysis, representing 13 personal and 54 area samples. Of the long-term personal samples, airborne concentrations of metals ranged from <0.001 to 2.9mg/m(3), and, in all but one case, resulted in concentrations below the current U.S. Occupational Safety and Health Administration's Permissible Exposure Limits and the American Conference of Governmental Industrial Hygienists' Threshold Limit Values. The arithmetic mean total dust concentration resulting from long-term personal samples was 0.31mg/m(3). The data presented here are the most complete set of its kind in the open literature, and are useful for understanding the potential exposures during solid catalyst handling activities at this petroleum refinery and perhaps other modern refineries during the timeframe examined.

An independent review and prioritization of past radionuclide and chemical releases from the Los Alamos National Laboratory--implications for future dose reconstruction studies.

From 1999 through 2010, a team of scientists and engineers systematically reviewed approximately eight million classified and unclassified documents at Los Alamos National Laboratory (LANL) that describe historical off-site releases of radionuclides and chemicals in order to determine the extent to which a full-scale dose reconstruction for releases is warranted and/or feasible. As a part of this effort, a relative ranking of historical airborne and waterborne radionuclide releases from LANL was established using priority index (PI) values that were calculated from estimated annual quantities released and the maximum allowable effluent concentrations according to The U.S. Nuclear Regulatory Commission (USNRC). Chemical releases were ranked based on annual usage estimates and U.S. Environmental Protection Agency (USEPA) toxicity values. PI results for airborne radionuclides indicate that early plutonium operations were of most concern between 1948 and 1961, in 1967, and again from 1970 through 1973. Airborne releases of uranium were found to be of most interest for 1968, from 1974 through 1978, and again in 1996. Mixed fission products yielded the highest PI value for 1969. Mixed activation product releases yielded the highest PI values from 1979 to 1995. For waterborne releases, results indicate that plutonium is of most concern for all years evaluated with the exception of 1956 when (90)Sr yielded the highest PI value. The prioritization of chemical releases indicate that four of the top five ranked chemicals were organic solvents that were commonly used in chemical processing and for cleaning. Trichloroethylene ranked highest, indicating highest relative potential for health effects, for both cancer and non-cancer effects. Documents also indicate that beryllium was used in significant quantities, which could have lead to residential exposures exceeding established environmental and occupational exposure limits, and warrants further consideration. In part because of the close proximity of residents to LANL, further study of historical LANL releases and the potential impact to public health is recommended for those materials with the largest priority index values; namely, plutonium, uranium, and selected chemicals.

Occupational exposure to benzene at the ExxonMobil refinery in Baytown, TX (1978-2006).

Although occupational benzene exposure of refinery workers has been studied for decades, no extensive analysis of historical industrial hygiene data has been performed focusing on airborne concentrations at specific refineries and tasks. This study characterizes benzene exposures at the ExxonMobil Baytown, TX, refinery from 1978 to 2006 to understand the variability in workers' exposures over time and during different job tasks. Exposures were grouped by operational status, job title, and tasks. More than 9000 industrial hygiene air samples were evaluated; approximately 4000 non-task (> 3 h) and 1000 task-related (< 3 h) personal samples were considered. Each sample was assigned to one of 27 job titles, 29 work areas, and 16 task bins (when applicable). Process technicians were sampled most frequently, resulting in the following mean benzene concentrations by area: hydrofiner (n=245, mean=1.3 p.p.m.), oil movements (n=286, mean=0.23 p.p.m.), reformer (n=575, mean=0.10 p.p.m.), tank farm (n=9, mean=0.65 p.p.m.), waste treatment (n=446, mean=0.13 p.p.m.), and other areas (n=460, mean=0.062 p.p.m.). The most frequently sampled task was sample collection (n=218, mean=0.40 p.p.m.). Job title and area did not significantly impact task-related exposures. Airborne concentrations were significantly lower after 1990 than before 1990. Results of this task-focused study may be useful when analyzing benzene exposures at other refineries.

Airborne concentrations of benzene for dock workers at the ExxonMobil refinery and chemical plant, Baton Rouge, Louisiana, USA (1977-2005).

OBJECTIVES: Benzene is a natural constituent of crude oil and natural gas (0.1-3.0% by volume). Materials that are refined from crude oil and natural gas contain some residual benzene. Few datasets have appeared in the peer-reviewed literature characterizing exposures to benzene at specific refineries or during specific tasks. In this study, historical samples of airborne benzene collected from 1977-2005 at the ExxonMobil Baton Rouge, Louisiana, USA, docks were evaluated. METHODS: Workers were categorized into 11 job titles, and both non-task (≤180 min sample duration) and task-related (<180 min) benzene concentrations were assessed. Approximately 800 personal air samples (406 non-task and 397 task-related) were analyzed. RESULTS: Non-task samples showed that concentrations varied significantly across job titles and generally resulted from exposures during short-duration tasks such as tank sampling. The contractor - tankerman job title had the highest average concentration [N=38, mean 1.4 parts per million (ppm), standard deviation (SD) 2.6]. Task-related samples indicated that the highest exposures were associated with the disconnection of cargo loading hoses (N=134, mean 11 ppm, SD 32). Non-task samples for specific job categories showed that concentrations have decreased over the past 30 years. Recognizing the potential for benzene exposure, this facility has required workers to use respiratory protective equipment during selected tasks and activities; thus, the concentrations measured were likely greater than those that the employee actually experienced. CONCLUSIONS: This study provides a job title- and task-focused analysis of occupational exposure to benzene during dock facility operations that is insightful for understanding the Baton Rouge facility and others similar to it over the past 30 years.

Benzene exposure in refinery workers: ExxonMobil Joliet, Illinois, USA (1977-2006).

While petroleum industry studies have indicated low benzene exposure potential for refinery workers, most provide limited data for assessing job or task-related benzene exposures. This study characterizes job and task-specific airborne benzene concentrations and variability over time for the ExxonMobil refinery in Joliet, Illinois from 1977 to 2006. A database of 2289 industrial hygiene air samples, including 1145 non-task (≥180 min) personal samples and 480 task-related (<180 min) personal samples, were analyzed. Samples were grouped by operational status, job, and task. Benzene concentrations were determined for each job category and task bin, with additional analyses conducted to determine whether benzene concentrations changed over time. The results indicate that the benzene concentrations for non-task and task samples were relatively low. For all non-task samples, the arithmetic mean benzene concentration was 0.12 part per million (ppm). The most frequently sampled workers (process technicians during routine operations) had an arithmetic mean benzene concentration of 0.038 ppm. The most frequently sampled task bin (blinding and breaking) had an arithmetic mean benzene concentration of 1.0 ppm. This study provides benzene air concentration data that can be used in combination with job histories to reconstruct historical benzene exposures for workers at the Joliet Refinery over the past 30 years.