RESUMEN
The present study further explores the behavior of polyoxometalate-based hybrid compounds as catalysts for liquid-phase cyclooctene epoxidation with H2O2. Precisely, it unveils the nature of the relevant active species derived from the hybrid based on Keggin polyoxometalate (POM) and bipyridines (bpy) of formula (2,2'-Hbpy)3[PW12O40] (1). Whereas (i) it is generally accepted that the catalytic oxidation of organic substrates by H2O2 involving Keggin HPAs proceeds via an oxygen transfer route from a peroxo intermediate and (ii) the catalytically active peroxo species is commonly postulated to be the polyperoxotungstate {PO4[W(O)(O2)2]4}3- complex (PW4), we show that the studied epoxidation reaction seems to be more sophisticated than commonly reported. During the catalytic epoxidation, 1 underwent a partial transformation into two oxidized species, 2 and 3. Compound 3 corresponding to 2,2'-bipyridinium oxodiperoxotungstate of formula [WO(O2)2(2,2'-bpy)] was shown to be the main species responsible for the selective epoxidation of cyclooctene since 2 (in which the POM is associated with a protonated mono-N-oxide derivative of 2,2'-bpy of formula (2,2'-HbpyO)3[PW12O40]) exhibited no activity. The structures of 1, 2, and 3 were solved by single-crystal X-ray diffraction and were independently synthesized. The speciation of 1 was monitored under catalytic conditions by 1H and 1H DOSY NMR spectroscopies, where the formation in situ of 2 and 3 was revealed. A reaction mechanism is proposed that highlights the pivotal, yet often underestimated, role of H2O2 in the reached catalytic performances. The active species responsible for the oxygen transfer to cyclooctene is a hydroperoxide intermediate species that is formed by the interaction between the anionic structure of the catalyst and H2O2. The latter operates as a "conservative agent" whose presence in the catalytic system is required to prevent the catalysts from deactivating irreversibly.
RESUMEN
Clays are often envisaged as an alternative to activated carbon for wastewater pollutant adsorption. However, conclusive results have only been obtained for clays heavily chemically modified. In this study, a greener approach is proposed to improve the retention capacity of clays. It consists in mixing clay (C) with eggshell (ES) and calcine, and then exposing to gliding arc plasma (ESC-800/PL). The resulting materials were characterized by nitrogen physisorption, FTIR, XRD, TGA/DTG, and point of zero charge analyses. The preparation gives porous platelet agglomerates resulting from the kaolinite-metakaolinite transition, thereby increasing their internal specific surface area and capacity to retain pollutants. This granular distribution is kept stable by partial pozzolanic reactions avoiding deagglomeration. The specific surface area and total pore volume increased respectively from 14 m2 g-1 and 0.049 cm3 g-1 to 89 m2 g-1 and 0.061 cm3 g-1 leading to an enhanced removal efficiency of Fast Green and Orange G dyes from polluted water. The maximum adsorption capacity occurred at 298 K attaining values of 32.34 and 14.78 mg g-1 for OG and FG, respectively. The pH plays a crucial role in the maximum sorption of dyes, and the experimental data were successfully adjusted to pseudo-first-order kinetic and Liu isotherm model.
Asunto(s)
Aguas Residuales , Contaminantes Químicos del Agua , Arcilla/química , Porosidad , Caolín , Colorantes , Adsorción , Cinética , Contaminantes Químicos del Agua/análisis , Concentración de Iones de HidrógenoRESUMEN
A thorough investigation of two novel hybrid materials, namely, (2,2'-Hbpy)3[PW12O40] and (4,4'-H2bpy)1.5[PW12O40]·1.5H2O built from Keggin phosphotungstic acid (PTA) and bipyridine, describes the impact of bipyridine isomers in their formation and physicochemical properties. The hybrids' formation was confirmed by powder X-ray diffraction, while infrared spectroscopy (IR) proved the polyoxometalate (POM) structural preservation. The stoichiometric composition and thermal stability of the hybrids were solved by thermogravimetric analysis-mass spectrometry, which also revealed newly acquired hydrophobic properties. Raman and IR spectroscopies demonstrated that the POM skeleton units in both hybrids were distorted compared to the POM in PTA, which induced a decrease of their reduction potentials as observed by diffuse reflectance ultraviolet-visible spectroscopy (DR-UV-vis). The hybrids' acidity was assessed by ammonia temperature-programmed desorption, which showed no remaining acid sites compared to the strong acidic character of the pristine PTA. The properties of the hybrids were tested in the epoxidation of cyclooctene in the presence of H2O2. The reaction was boosted when the hybrids were pre-activated with H2O2.
RESUMEN
This paper studies the effect of the direct incorporation of ZrO2 in TiO2 and TiO2-CeO2 aerogel supports prepared by sol-gel route on the physico-chemical and catalytic properties of supported vanadia catalysts in the total oxidation of chlorobenzene. The obtained catalysts have been characterized by means of ICP-AES, N2 adsorption-desorption at 77 K, XRD, XPS, H2-TPR and NH3-TPD. The results revealed that Zr-doped V2O5 based catalyst is beneficial for the improvement of catalytic properties in chlorobenzene total oxidation. In particular, in the absence of cerium groups, this beneficial effect is correlated with the better acidic properties or/and the stabilization of the V2O5 active phase in a higher oxidation state. However, in the case of cerium rich catalyst, this positive effect is much stronger thanks to the enhanced redox properties of V2O5/TiO2-CeO2-ZrO2.
RESUMEN
Imparting hydrophobicity to solid acid catalysts is critical to regulating their performances by allowing the creation of a less polar environment and improved partitioning of the reactants. Here we present different approaches for the preparation of silica-based catalysts comprising sulfonic acid (-SO3H) sites and hydrophobic decyl (-C10) chains by either simultaneous or sequential postfunctionalization of an azide-functionalized mesoporous silica platform. This set of hybrid bifunctional catalysts is compared in the model esterification of octanol with acetic acid, and the influence of the preparation methods together with the resulting site spatial distribution is discussed. In parallel, we show that pairing the two functional groups affords a maximum synergistic effect compared to more traditional mixed catalysts with random distributions of acid and hydrophobic functions.
RESUMEN
Intermetallic compounds (IMCs) have diverse electronic and geometrical properties to offer. However, the synthesis of intermetallic nanoparticles is not always easy; developing new methodologies that are conventional for many systems can be challenging, especially when incorporating highly electropositive metals to reduce to IMCs using solution synthesis methodologies. In this study, we report a comprehensive approach to access nanocrystalline PdxMy (M = Cu, Zn, Ga, Ge, Sn, Pb, Cd, In) intermetallic (IM) via the coreduction method employing sodium borohydride as the reductant. A combination of diffraction, spectroscopic, and microscopic techniques were performed to characterize the formed nanoparticles in terms of their phase composition, purity, particle size distribution, and surface oxidation properties of metals, respectively. IMCs of Pd with the elements such as Cu, Zn, Ga, and Ge exhibited higher catalytic activity that with elements such as In, Sn, Pb, and Cd. The DFT studies on these compounds revealed that the adsorption of benzylamine at the Pd site and the dissociative adsorption of O2 on the IM surface play a significant effect on catalytic activity. Among them, PdCu IM exhibited an excellent conversion of benzylamine (94.0%), with 92.2% of dibenzylimine selectivity compared to other IMCs. Moreover, PdCu exhibited decent recyclability and activity for the oxidation of different substituted primary amines.
RESUMEN
Solid acid catalysts are central in our chemical industry and are major players in the valorization of bioresources. However, there is still a need to develop solid acid catalysts with enhanced acid strength and improved, or tunable, physicochemical profile to enhance the efficiency and sustainability of chemical processes. Here, a modular approach to tune the acid strength and surface polarity of silica-supported sulfonic acid catalysts, based on a versatile copper-catalyzed azide-alkyne cycloaddition (CuAAC)-based anchoring scheme, is presented. The CuAAC-formed triazole link was used to enhance the activity of the grafted sulfonic acids and to pair the acid sites with secondary hydrophobic functions. The beneficial effects of both the triazolium link and the paired hydrophobic site, as well as the optimal positioning of the sulfonic moiety on the triazole ring, are discussed in model esterification reactions.
RESUMEN
The picloram (PCM) adsorption on nontronite, illite and kaolinite was studied at pH 3, 5 and 7. The adsorption isotherms had well-fitted to Langmuir and Freundlich models equations. The interactions of PCM with the clay mineral surfaces exhibited an anionic profile adsorption, with a decrease in adsorption when the pH increases. The PCM adsorption capacity increases in the following order: kaolinite < illite < nontronite. The X-ray diffraction (XRD) analysis of PCM-clay samples revealed that the picloram molecule does not enter into the clays basal space. The interaction of PCM with clays surface sites through nitrogen of the pyridine ring was confirmed by X-ray photoelectron spectroscopy (XPS). Due to the anionic form of PCM, the adsorption onto the external and edges surface sites of the clay minerals was proposed.
Asunto(s)
Arcilla/química , Caolín/química , Minerales/química , Picloram/aislamiento & purificación , Adsorción , Herbicidas/química , Herbicidas/aislamiento & purificación , Concentración de Iones de Hidrógeno , Espectroscopía de Fotoelectrones , Picloram/química , Difracción de Rayos XRESUMEN
In the field of heterogeneous catalysis, the successful integration of enzymes and inorganic catalysts could pave the way to multifunctional materials which are able to perform advanced cascade reactions. However, such combination is not straightforward, for example in the case of zeolite catalysts for which enzyme immobilization is restricted to the external surface. Herein, this challenge is overcome by developing a new kind of hybrid catalyst based on hollow zeolite microspheres obtained by the aerosol-assisted assembly of zeolite nanocrystals. The latter spheres possess open entry-ways for enzymes, which are then loaded and cross-linked to form cross-linked enzyme aggregates (CLEAs), securing their entrapment. This controlled design allows the combination of all the decisive features of the zeolite with a high enzyme loading. A chemo-enzymatic reaction is demonstrated, where the structured zeolite material is used both as a nest for the enzyme and as an efficient inorganic catalyst. Glucose oxidase (GOx) ensures the in situ production of H2O2 subsequently utilized by the TS-1 zeolite to catalyze the epoxidation of allylic alcohol toward glycidol. The strategy can also be used to entrap other enzymes or combination of enzymes, as demonstrated here with combi-CLEAs of horseradish peroxidase (HRP) and glucose oxidase. We anticipate that this strategy will open up new perspectives, leveraging on the spray-drying (aerosol) technique to shape microparticles from various nano-building blocks and on the entrapment of biological macromolecules to obtain new multifunctional hybrid microstructures.
RESUMEN
The catalytic combustion of diesel soot is addressed with flexible and structured "paper catalysts". Two different series of catalysts were prepared either by drip impregnation or by a spray method to deposit a mixture of Co, Ba, and K or a mixture of Co and Ce onto SiO2-Al2O3 ceramic paper matrixes. In every case, CeO2 nanoparticles were added to bind the ceramic fibers. SEM images showed that the impregnation method generated catalytic particles concentrated as large chunks (> 10 µm), mainly at ceramic fiber crossings, whereas the spray method produced smaller catalytic particles (< 1 µm) well distributed throughout the ceramic paper. Besides, Co-Ba-K particles appeared better dispersed on the surface of ceramic fibers than Co-Ce due to the presence of K. Additionally, FTIR spectra showed the formation of O22- and O2- species associated with CeO2 (binder) on the samples containing potassium which gave the Co-Ba-K-ceramic paper good catalytic properties, thus making the Co-Ba-K drop impregnated the best catalyst both considering activity and stability. Successive temperature programmed oxidation (TPO) runs up to 700 °C caused the formation of cobalt silicates in the catalytic ceramic paper prepared by the spray method, as indicated by TPR. The formation of these species was probably favored by the smaller size of cobalt particulates and their higher dispersion in the catalysts prepared by the spray method. This provoked the partial loss of the redox properties of Co3O4. TPR experiments also indicated the formation of BaCoO3 in Ba-containing ceramic paper, which could help in maintaining the catalyst activity after several TPO runs through the capacity of this mixed perovskite-type oxide to trap and release NOx.
Asunto(s)
Filtros de Aire , Cerámica/química , Emisiones de Vehículos/análisis , Compuestos de Calcio , Catálisis , Cerio/química , Cobalto/química , Oxidación-Reducción , Óxidos , Dióxido de Silicio , Hollín/química , Titanio , Emisiones de Vehículos/prevención & controlRESUMEN
In this paper, TiO2 prepared with an aqueous sol-gel synthesis by peptization process is doped with nitrogen precursor to extend its activity towards the visible region. Three N-precursors are used: urea, ethylenediamine and triethylamine. Different molar N/Ti ratios are tested and the synthesis is adapted for each dopant. For urea- and trimethylamine-doped samples, anatase-brookite TiO2 nanoparticles of 6-8 nm are formed, with a specific surface area between 200 and 275 m²·g-1. In ethylenediamine-doped samples, the formation of rutile phase is observed, and TiO2 nanoparticles of 6-8 nm with a specific surface area between 185 and 240 m²·g-1 are obtained. X-ray photoelectron spectroscopy (XPS) and diffuse reflectance measurements show the incorporation of nitrogen in TiO2 materials through Ti-O-N bonds allowing light absorption in the visible region. Photocatalytic tests on the remediation of water polluted with p-nitrophenol show a marked improvement for all doped catalysts under visible light. The optimum doping, taking into account cost, activity and ease of synthesis, is up-scaled to a volume of 5 L and compared to commercial Degussa P25 material. This up-scaled sample shows similar properties compared to the lab-scale sample, i.e., a photoactivity 4 times higher than commercial P25.
RESUMEN
Characterizing catalysts under working conditions is crucial to understand and to optimize their behavior and performance. However, when Raman spectroscopy is used, attention has to be paid to laser-induced artefacts. While laser irradiation is often claimed to lead to a temperature gradient between the integral catalyst bed and the sampling point, neither the circumstances when such effect appears, nor if it systematically occurs or not, are really explored in details. The present paper shows that the sensitivity of a catalyst to laser-induced heating largely depends on the gas composition under which the analysis is done, in particular that it depends whether the catalyst has adsorbed reactant molecules or not. These aspects are here addressed via the Raman in situ exploration of H3PW12O40. This heteropolyacid is a widely used acid catalyst due to its very high Brönsted acidity, approaching the superacid region. In particular, we have investigated the impact of laser irradiation in the Raman monitoring of solid H3PW12O40 at work under a flow of methanol in nitrogen at 50°C. When 1 single spectrum of H3PW12O40 was measured after 3h of exposure to methanol, the characteristic CH vibration bands of adsorbed methanol appeared. However, when spectra were measured continuously throughout the experiment, the same CH vibration bands were observed only during the first hour, then they disappeared and the characteristic bands of polyaromatic molecules appeared. Under continuous laser irradiation, adsorbed methanol was thus converted into polyaromatic coke as resulting from a laser-induced heating. However, the spectra collected under pure nitrogen show that the laser does not heat the catalyst in the absence of methanol. UV-Vis revealed the reason of the laser-induced heating in the presence of methanol, and the subsequent formation of coke. Actually the catalyst gets reduced by the adsorbed methanol, what darkens the catalyst bed. Such a darkening renders the catalyst sensitive to laser-induced heating, which in turn leads to the formation of coke. Under continuous laser irradiation, methanol thus auto-initiated its own catalytic conversion, finally leading to the deposition of coke. Such artefact must be avoided if one wants to study the true behavior of the catalyst at work. This paper shows that, for reducible samples analyzed in the presence of reductive molecules, this is only possible by shining the laser intermittently and not continuously. More generally, it actually shows that the adequate way to irradiate a catalyst (continuous vs intermittent) in an in situ/operando Raman analysis depends on the gas flow composition.
RESUMEN
HYPOTHESIS: The environmental mobility and bioavailability of Picloram (PCM) are determined by the amine and carboxylate chemical groups interaction with the soils mineral phases. Clay particles, such as montmorillonite (Mt), and the pH value of the media could play an important role in adsorption processes. Thus, the study of the role of soil components other than organic matter deserves further investigation for a more accurate assessment of the risk of groundwater contamination. EXPERIMENTS: Samples with PCM adsorbed on Mt dispersions were prepared at pH 3-9. Subsequently, the dispersions were separated, washed, centrifuged and stored at room temperature. Picloram (PCM) herbicide interaction with surface groups of montmorillonite (Mt) was studied using XRD, DTA, FTIR and XPS techniques. FINDINGS: The entrance of PCM into the Mt basal space, in two different arrangements, perpendicular and planar, is proposed and the final arrangement depends on PCM concentration. The interaction of PCM with Mt surface sites through the nitrogen of the pyridine ring and carboxylic group of PCM, forming bidentate and bridge inner-sphere complexes was confirmed by FTIR and XPS analysis. The acidity constant of the PCM adsorbed on the Mt surface was calculated.
Asunto(s)
Bentonita/química , Herbicidas/química , Picloram/química , Adsorción , Silicatos de Aluminio/química , Arcilla , Espectroscopía de Fotoelectrones , Suelo/química , Espectroscopía Infrarroja por Transformada de Fourier , Propiedades de Superficie , Difracción de Rayos XRESUMEN
Hybridization of polyoxometalates (POMs) via an organic-inorganic association constitutes a new route to develop heterogeneous POM catalysts with tunable supramolecular architecture. As the structural stability of POMs is strongly influenced by the pH conditions, a quantitative understanding of the POMs-polymer association is important in practical applications. Herein, we use Quartz Crystal Microbalance (QCM) to systematically investigate the interactions of Keggin phosphotungstic acid POM with a polyampholyte polymer-coated QCM sensor as a function of pH. The mass of adsorbed POMs increases when pH decreases from 5.6 to 2, indicating that electrostatic forces play a major role in the formation of POM-polymer hybrids. This finding is complemented by AFM images that show an increase in the size of the hybrid entities from 5 to 12 nm as the pH decreases from 5.6 to 2. The POM adsorbed amount at a particular pH value reaches an equilibrium level with time. The hybrids further gain in adsorbed mass only when lowering the pH value of the POM solution. The hybrid structure formed above pH 2 shows resistance to leaching as indicated by the steady level of the adsorbed mass during a rinsing step with water. However, at pH 2, the rinsing step causes desorption of some weakly adsorbed POMs. It is shown that leached POMs can be re-adsorbed back into the polymer matrix during a second contact with a POM solution at pH 2. This adsorption-desorption cycles of POMs were successfully repeated. Our experiments shed light into the coexistence of tightly as well as loosely bound POMs in hybrid catalyst formed at pH 2. The loosely bound POMs can potentially act as homogeneous catalysts when desorbed. However, these leached POMs can be re-adsorbed back into the matrix, preserving the heterogeneous state of the catalyst. Our results show that QCM is a powerful technique to study in situ the dynamics of the adsorption of POMs on a polymer matrix under different pH conditions.
RESUMEN
The hybridization of polyoxometalates (POMs) through an organic-inorganic association offers several processing advantages in the design of heterogeneous catalysts. A clear understanding of the organization of these hybrid materials on solid surfaces is necessary to optimise their properties. Herein, we report for the first time the organization of Keggin phosphotungstic [PW12O40](3-) and Wells-Dawson (WD) phosphomolybdic [P2Mo18O62](6-) anions deposited on mica (hydrophilic), and highly oriented pyrolytic graphite (HOPG) (hydrophobic) surfaces. Next, the supramolecular organization of the organic-inorganic hybrid materials formed from the association of POM anions and dimethyldioctadecylammonium bromide (DODA) is investigated as a function of the hydrophilic or hydrophobic nature of the surfaces. The height of the Keggin-POM anions, measured with tapping mode (TM-AFM) is always in good agreement with the molecular dimension of symmetric Keggin-POM anions (ca. 1 nm). However, the asymmetric WD-POM anions form monolayer assemblies on the surfaces with the orientation of their long molecular axis (ca. 1.6 nm) depending on the hydrophilic or hydrophobic properties of the substrate. Namely, the long axis is parallel on mica, and perpendicular on HOPG. When hybridized with DODA, the organization of the hybrid material is dictated by the interaction of the alkyl side chains of DODA with the substrate surface. On HOPG, the DODA-POM hybrid forms small domains of epitaxially arranged straight nanorod structures with their orientation parallel to each other. Conversely, randomly distributed nanospheres are formed when the hybrid material is deposited on freshly cleaved mica. Finally, a UV-ozone treatment of the hybrid material allows one to obtain highly dispersed isolated POM entities on both hydrophilic and hydrophobic surfaces. The hybridization strategy to prevent the clustering of POMs on various supports would enable to develop highly dispersed POM-based heterogeneous catalysts with enhanced functionalities.
RESUMEN
CdS quantum dots were grown on mesoporous TiO2 films by successive ionic layer adsorption and reaction processes in order to obtain CdS particles of various sizes. AFM analysis shows that the growth of the CdS particles is a two-step process. The first step is the formation of new crystallites at each deposition cycle. In the next step the pre-deposited crystallites grow to form larger aggregates. Special attention is paid to the estimation of the CdS particle size by X-ray photoelectron spectroscopy (XPS). Among the classical methods of characterization the XPS model is described in detail. In order to make an attempt to validate the XPS model, the results are compared to those obtained from AFM analysis and to the evolution of the band gap energy of the CdS nanoparticles as obtained by UV-vis spectroscopy. The results showed that XPS technique is a powerful tool in the estimation of the CdS particle size. In conjunction with these results, a very good correlation has been found between the number of deposition cycles and the particle size.
RESUMEN
Investigations of X-ray photoelectron spectra from solid samples need corrections for the surface charging effect. For powder samples such as heterogeneous catalysts and their supports, the C-(C,H) component of the C 1s peak is often used as an internal standard for the calibration of the binding energy scale. Although this method is widely recognized as suitable for the study of heterogeneous catalysts, we show that a significant calibration bias can be encountered upon comparing samples with different bulk composition. In this paper, a series of SiO2-Al2O3 supports and Pd/SiO2-Al2O3 catalysts with various Si/Al ratios were studied. The spectra issued from these samples were processed with the classical calibration method on the basis of the carbon peak. Important discrepancies in the relative position of the photoelectron peaks were noticed. After systematically discarding instrument-related issues, a true chemical influence of the bulk matrix on the analyzed surface species was evidenced. The extent of this chemical effect was dependent on the composition of the sample and more precisely on its ionicity. Two possible mechanisms for this chemical effect were proposed and discussed. Finally, an alternative calibration method was offered.
RESUMEN
PURPOSE: We aimed to assess the fate of ß-arteether lipid-based drug delivery systems (AE-LBDDS) in terms of resistance to lipolysis and permeation across intestinal cells. METHODS: AE-LBDDS contained Tween 80 or Cremophor EL as surfactants, ethanol, Maisine 35-1 and vegetable oil. The solubilization behavior of AE was investigated during dynamic in vitro lipolysis. The permeation of AE-LBDDS was evaluated using Caco-2, HT29-MTX and M cell monolayers. RESULTS: A higher level of AE precipitation was observed for formulations containing Cremophor EL (~30%) compared to formulations containing Tween 80 (~10%) after lipolysis. However, rapid re-dissolution of the precipitated AE from LBDDS containing Cremophor EL in the intestinal biorelevant media was observed. The transport of AE loaded in LBDDS was enhanced in comparison to that of free drug due to the increased AE solubility. The apparent permeability of all AE-LBDDS across Caco-2 cell monolayers was approximately 3.10(-6) cm/s. A decrease in the permeability was observed at 4°C. M cells did not influence the transport of AE-LBDDS, and mucus decreased AE permeability when formulated with Tween 80. Furthermore, AE is not a P-glycoprotein substrate. CONCLUSION: LBDDS that are partly resistant to in vitro lipolysis significantly increased the transport of AE across intestinal cell monolayers.
Asunto(s)
Artemisininas/química , Portadores de Fármacos/química , Mucosa Intestinal/metabolismo , Lipólisis , Aceites de Plantas/química , Transporte Biológico , Células CACO-2 , Técnicas de Cultivo de Célula , Química Farmacéutica , Portadores de Fármacos/farmacocinética , Sistemas de Liberación de Medicamentos/métodos , Células HT29 , Humanos , Modelos Biológicos , Permeabilidad , SolubilidadRESUMEN
Hybridization of polyoxometalates (POMs) via the formation of an organic-inorganic association constitutes a new route to develop a heterogeneous POM catalyst with tunable functionality imparted through supramolecular assembly. Herein, we report on strategies to obtain tunable well-defined supramolecular architectures of an organic-inorganic heterogeneous hybrid catalyst formed by the association of a hydrophobically substituted polyampholyte copolymer (poly N, N-diallyl-N-hexylamine-alt-maleic acid) and phosphotungstic acid (H3PW12O40) POMs. The self-assembling property of the initial polyampholyte copolymer matrix is modulated by controlling the pH of the hybridization solution. When deposited on a mica surface, isolated, long and extended polymer chains are formed under basic conditions (pH 7.9), while globular or coiled structures are formed under acidic conditions (pH 2). The supramolecular assembly of the POM-polymer hybrid is found to be directed by the type and quantities of charges present on the polyampholyte copolymer, which themselves depend on the pH conditions. The hypothesis is that the Keggin type [PW12O40](3-) anions, which have a size of ~1 nm, electrostatically bind to the positive charge sites of the polymer backbone. The hybrid material stabilized at pH 5.3 consists of POM-decorated polymer chains. Statistical analysis of distances between pairs of POM entities show narrow density distributions, suggesting that POM entities are attached to the polymer chains with a high level of order. Conversely, under acidic conditions (pH 2), the hybrid shows the formation of a core-shell type of structure. The strategies reported here, to tune the supramolecular assembly of organic-inorganic hybrid materials, are highly valuable for the design and a more rational utilization of POM heterogeneous catalysts in several chemical transformations.
Asunto(s)
Polímeros/química , Catálisis , Sustancias Macromoleculares/síntesis química , Sustancias Macromoleculares/química , Modelos Moleculares , Estructura Molecular , Tamaño de la Partícula , Polímeros/síntesis química , Propiedades de SuperficieRESUMEN
A Periodic Mesoporous Organosilica (PMO) functionalized with sulfonic acid groups has been successfully synthesized via a sequence of post-synthetic modification steps of a trans-ethenylene bridged PMO material. The double bond is functionalized via a bromination and subsequent substitution obtaining a thiol functionality. This is followed by an oxidation towards a sulfonic acid group. After full characterization, the solid acid catalyst is used in the acetylation of glycerol. The catalytic reactivity and reusability of the sulfonic acid modified PMO material is investigated. The catalyst showed a catalytic activity and kinetics that are comparable with the commercially available resin, Amberlyst-15, and furthermore our catalyst can be recycled for several subsequent catalytic runs and retains its catalytic activity.