Lead Isolation and Capture in Perovskite Photovoltaics toward Eco-Friendly Commercialization.

Perovskite solar cells (PSCs) are developed rapidly in efficiency and stability in recent years, which can compete with silicon solar cells. However, an important obstacle to the commercialization of PSCs is the toxicity of lead ions (Pb2+) from water-soluble perovskites. The entry of free Pb2+ into organisms can cause severe harm to humans, such as blood lead poisoning, organ failure, etc. Therefore, this work reports a "lead isolation-capture" dual detoxification strategy with calcium disodium edetate (EDTA Na-Ca), which can inhibit lead leakage from PSCs under extreme conditions. More importantly, leaked lead exists in a nontoxic aggregation state chelated by EDTA. For the first time, in vivo experiments are conducted in mice to systematically prove that this material has a significant inhibitory effect on the toxicity of perovskites. In addition, this strategy can further enhance device performance, enabling the optimized devices to achieve an impressive power conversion efficiency (PCE) of 25.19%. This innovative strategy is a major breakthrough in the research on the prevention of lead toxicity in PSCs.

Magnetic-biased chiral molecules enabling highly oriented photovoltaic perovskites.

The interaction between sites A, B and X with passivation molecules is restricted when the conventional passivation strategy is applied in perovskite (ABX3) photovoltaics. Fortunately, the revolving A-site presents an opportunity to strengthen this interaction by utilizing an external field. Herein, we propose a novel approach to achieving an ordered magnetic dipole moment, which is regulated by a magnetic field via the coupling effect between the chiral passivation molecule and the A-site (formamidine ion) in perovskites. This strategy can increase the molecular interaction energy by approximately four times and ensure a well-ordered molecular arrangement. The quality of the deposited perovskite film is significantly optimized with inhibited nonradiative recombination. It manages to reduce the open-circuit voltage loss of photovoltaic devices to 360 mV and increase the power conversion efficiency to 25.22%. This finding provides a new insight into the exploration of A-sites in perovskites and offers a novel route to improving the device performance of perovskite photovoltaics.

Electronically Manipulated Molecular Strategy Enabling Highly Efficient Tin Perovskite Photovoltaics.

Buried interface modification can effectively improve the compatibility between interfaces. Given the distinct interface selections in perovskite solar cells (PSCs), the applicability of a singular modification material remains limited. Consequently, in response to this challenge, we devised a tailored molecular strategy based on the electronic effects of specific functional groups. Therefore, we prepared three distinct silane coupling agents, and due to the varying inductive effects of these functional groups, the electronic distribution and molecular dipole moments of the coupling agents are correspondingly altered. Among them, trimethoxy (3,3,3-trifluoropropyl)-silane (F3 -TMOS), which possesses electron-withdrawing groups, generates a molecular dipole moment directed toward the hole transport layer (HTL). This approach changes the work function of the HTL, optimizes the energy level alignment, reduces the open-circuit voltage loss, and facilitates carrier transport. Furthermore, through the buffering effect of the coupling agent, the interface strain and lattice distortion caused by annealing the perovskite are reduced, enhancing the stability of the tin-based perovskite. Encouragingly, tin PSCs treated with F3 -TMOS achieved a champion efficiency of 14.67 %. This strategy provides an expedient avenue for the design of buried interface modification materials, enabling precise molecular adjustments in accordance with distinct interfacial contexts to ameliorate mismatched energetics and enhance carrier dynamics.

Ion-Dipole Interaction Enabling Highly Efficient CsPbI3 Perovskite Indoor Photovoltaics.

Metal halide perovskites are ideal candidates for indoor photovoltaics (IPVs) because of their easy-to-adjust bandgaps, which can be designed to cover the spectrum of any artificial light source. However, the serious non-radiative carrier recombination under low light illumination restrains the application of perovskite-based IPVs (PIPVs). Herein, polar molecules of amino naphthalene sulfonates are employed to functionalize the TiO2 substrate, anchoring the CsPbI3 perovskite crystal grains with a strong ion-dipole interaction between the molecule-level polar interlayer and the ionic perovskite film. The resulting high-quality CsPbI3 films with the merit of defect-immunity and large shunt resistance under low light conditions enable the corresponding PIPVs with an indoor power conversion efficiency of up to 41.2% (Pin : 334.11 µW cm-2 , Pout : 137.66 µW cm-2 ) under illumination from a commonly used indoor light-emitting diode light source (2956 K, 1062 lux). Furthermore, the device also achieves efficiencies of 29.45% (Pout : 9.80 µW cm-2 ) and 32.54% (Pout : 54.34 µW cm-2 ) at 106 (Pin : 33.84 µW cm-2 ) and 522 lux (Pin : 168.21 µW cm-2 ), respectively.

Significant enhancement of scintillation performance by inducing oxygen vacancies in alkali metal ion (A+ = Li+, Na+, K+)-incorporated (Lu, Sc)BO3:Ce.

The incorporation of Sc3+ can stabilize calcite-phase LuBO3:Ce3+ to grow large-sized single crystals but leads to the significant degradation of scintillation performance. In the present work, alkali metal ion (A+ = Li+, Na+, K+)-incorporated (Lu, A, Sc)BO3:Ce was rapidly synthesized in batches via a high-throughput sol-gel method. The aliovalent substitution of Lu3+ with A+ is balanced by the generation of oxygen vacancies by forming complexes. Thanks to the increased oxygen vacancies, the luminescence and XEL intensity of (Lu, Li, Sc)BO3:Ce are significantly enhanced by 2.2 times and 1.9 times, respectively. Further, the incorporation of A+ is attributed to the improved transition efficiency of charge carriers. The prepared scintillation screen fabricated with LASBO:Ce and PMMA shows that the spatial resolution can reach 8.6 lp mm-1, indicating its potential application in efficient and low-cost non-destructive X-ray detection. This work is of great significance in improving the luminescence and scintillation performance of (Lu, Sc)BO3:Ce single crystals and thin films and their application in the scintillation field.

Full-Dimensional Grain Boundary Stress Release for Flexible Perovskite Indoor Photovoltaics.

Perovskite photovoltaics are strong potential candidates to drive low-power off-grid electronics for indoor applications. Compared with rigid devices, flexible perovskite devices can provide a more suitable surface for indoor small electronic devices, enabling them have a broader indoor application prospect. However, the mechanical stability of flexible perovskite photovoltaics is an urgent issue solved. Herein, a kind of 3D crosslinking agent named borax is selected to carry out grain boundary penetration treatment on perovskite film to realize full-dimensional stress release. This strategy improves the mechanical and phase stabilities of perovskite films subjected to external forces or large temperature changes. The fabricated perovskite photovoltaics deliver a champion power conversion efficiency (PCE) of 21.63% under AM 1.5G illumination, which is the highest one to date. The merit of low trap states under weak light makes the devices present a superior indoor PCE of 31.85% under 1062 lux (LED, 2956 K), which is currently the best flexible perovskite indoor photovoltaic device. This work provides a full-dimensional grain boundary stress release strategy for highly stable flexible perovskite indoor photovoltaics.

Improved Phase Stability and Enhanced Luminescence of Calcite Phase LuBO3:Ce3+ through Ga3+ Incorporation.

The application of LuBO3:Ce3+ (LBO:Ce) crystal as an excellent scintillation material has been limited due to its poor phase stability at high temperature or high pressure, so improving the phase stability is essential for promoting its development. Ga stabilized LuBO3:Ce3+ (LGBO:Ce) is synthesized by solid-state reaction at 1200 °C. Powder X-ray diffraction patterns and Raman spectra at ambient pressure show that all the samples are pure calcite phase. In situ high-pressure synchrotron radiation XRD patterns illustrate that calcite phase LGBO:Ce exhibits more excellent phase stability than that of LBO:Ce under high pressure due to the superior compressibility of the [GaO6] octahedral unit. The optical band gap of LGBO decreases from 5.58 to 4.64 eV after introducing 10% Ga, which leads to the decreased nonradiative transition and about double luminescence intensity as expected. More interestingly, the charge transition from O2- to Ce4+ is observed at about 290 nm in the absorption spectra. The X-ray photoelectron spectroscopy spectra indicate the ratio of Ce4+/Ce3+ increases with increasing concentration of Ga3+, which can be attributed to the variation of energy separation between the 4f ground state of Ce3+ and the Fermi energy level position. In contrast to the enhancement of PL intensity, the integrated X-ray excited luminescence intensity decreases after Ga3+ incorporation attributing to the result of both decreased effective atomic number and ionization energy between 5d1 level and conduction band. The thermal luminescence spectra show that after the incorporation of Ga3+ the oxygen vacancy and intrinsic defects in LBO remain unchanged but that the concentration of oxygen vacancy significantly reduces. The mechanism of Ga3+ incorporation on phase stability and luminescence properties of LBO:Ce has been proposed and discussed systematically.

Perovskite Grains Embraced in a Soft Fullerene Network Make Highly Efficient Flexible Solar Cells with Superior Mechanical Stability.

Halide perovskite films processed from solution at low-temperature offer promising opportunities to make flexible solar cells. However, the brittleness of perovskite films is an issue for mechanical stability in flexible devices. Herein, photo-crosslinked [6,6]-phenylC61 -butyric oxetane dendron ester (C-PCBOD) is used to improve the mechanical stability of methylammonium lead iodide (MAPbI3 ) perovskite films. Also, it is demonstrated that C-PCBOD passivates the grain boundaries, which reduces the formation of trap states and enhances the environmental stability of MAPbI3 . Thus, MAPbI3 perovskite solar cells are prepared on solid and flexible substrates with record efficiencies of 20.4% and 18.1%, respectively, which are among the highest ever reported for MAPbI3 on both flexible and solid substrates. The result of this work provides a step improvement toward stable and efficient flexible perovskite solar cells.

Pb-Sn-Cu Ternary Organometallic Halide Perovskite Solar Cells.

Exploiting organic/inorganic hybrid perovskite solar cells (PSCs) with reduced Pb content is very important for developing environment-friendly photovoltaics. Utilizing of Pb-Sn alloying perovskite is considered as an efficient route to reduce the risk of ecosystem pollution. However, the trade-off between device performance and Sn substitution ratio due to the instability of Sn2+ is a current dilemma. Here, for the first time, the highly efficient Pb-Sn-Cu ternary PSCs are reported by partial replacing of PbI2 with SnI2 and CuBr2 . Sn2+ substitution results in a redshift of the absorption onset, whereas worsens the film quality. Interestingly, Cu2+ introduction can passivate the trap sites at the crystal boundaries of Pb-Sn perovskites effectively. Consequently, a power conversion efficiency as high as 21.08% in inverted planar Pb-Sn-Cu ternary PSCs is approached. The finding opens a new route toward the fabrication of high efficiency Pb-Sn alloying perovskite solar cells by Cu2+ passivation.

Small Molecule-Polymer Composite Hole-Transporting Layer for Highly Efficient and Stable Perovskite Solar Cells.

Effective and stable hole-transporting materials (HTMs) are necessary for obtaining excellent planar perovskite solar cells (PSCs). Herein, we reported a solution-processed composite HTM consisting of a polymer poly(3,4-ethylenedioxythiophene):polystyrenesulfonate (PEDOT:PSS) and a small-molecule copper phthalocyanine-3,4',4″,4‴-tetrasulfonated acid tetrasodium salt (TS-CuPc) with optimized doping ratios. The composite HTM is crucial for not only enhancing the hole transport and extraction but also improving the perovskite crystallization. In addition, the composite HTM can weaken the indium tin oxide erosion by reducing the acidity and increasing the dispersibility of the PEDOT:PSS aqueous dispersion via incorporating suitable TS-CuPc. Consequently, a highly efficient device was fabricated with a power conversion efficiency (PCE) of 17.29%. Its short-circuit current (JSC) is 22.23 mA/cm2, and its open-circuit voltage (VOC) is 1.01 V. Meanwhile, it exhibited a higher fill factor (FF) of 77% and improved cell stability. The developed composite HTM provides a good potential anode interfacial layer for fabricating outstanding PSCs.

Origin of Magnetism in Hydrothermally Aged 2-Line Ferrihydrite Suspensions.

As an iron oxyhydroxide, nanosized ferrihydrite (Fh) is important in Earth science, biology, and industrial applications. However, its basic structure and origin of its magnetism have long been debated. We integrate synchrotron-based techniques to explore the chemical structures of 2-line ferrihydrite and to determine the origin of its magnetism during hydrothermal aging in air. Our results demonstrate that both the magnetism and X-ray magnetic circular dichroism (XMCD) signal of 2-line ferrihydrite are enhanced with aging time, and that XMCD spectral patterns resemble that of maghemite (γ-Fe2O3) rather than magnetite (Fe3O4). Fe L-edge and K-edge X-ray absorption spectroscopy (XAS) further indicate formation of both maghemite and hematite (α-Fe2O3) with increasing concentrations with longer hydrothermal aging time. Thus, magnetic enhancement with longer hydrothermal aging time is attributed to increasing maghemite concentration instead of a magnetically ordered ferrihydrite as previously reported. Moreover, L-edge and K-edge XAS spectra with different probing depths yield different ratios of these Fe oxides, which suggest the formation of a core (ferrihydrite-rich)-shell (with a mixture of both allotropes; α-Fe2O3 and γ-Fe2O3) structure during hydrothermal aging. Our results provide insights into the chemical evolution of 2-line ferrihydrite that reveal unambiguously the origin of its magnetism.

Perovskite Solar Cells: High Efficiency Pb-In Binary Metal Perovskite Solar Cells (Adv. Mater. 31/2016).

On page 6695, X. Y. Gao, L.-S. Liao, and co-workers describe the fabrication of mixed Pb-In perovskite solar cells, using indium (III) chloride and lead (II) chloride with methylammonium iodide. A maximum power conversion efficiency as high as 17.55% is achieved owing to the high quality of the perovskites with multiple ordered crystal orientations. This work demonstrates the possibility of substituting the Pb (II) by using In (III), which opens a broad route to fabricating alloy perovskite solar cells with mitigated ecological impact.

High Efficiency Pb-In Binary Metal Perovskite Solar Cells.

Mixed Pb-In perovskite solar cells are fabricated by using lead(II) chloride and indium(III) chloride with methylammonium iodide. A maximum power conversion efficiency as high as 17.55% is achieved owing to the high quality of perovskites with multiple ordered crystal orientations.

Evolution of the SrTiO3-MoO3 Interface Electronic Structure: An in Situ Photoelectron Spectroscopy Study.

Modifying the surface energetics, particularly the work function of advanced materials, is of critical importance for a wide range of surface- and interface-based devices. In this work, using in situ photoelectron spectroscopy, we investigated the evolution of electronic structure at the SrTiO3 surface during the growth of ultra-thin MoO3 layers. Because of the large work function difference between SrTiO3 and MoO3, the energy band alignment on the SrTiO3 surface is significantly modified. The charge transfer and dipole formation at the SrTiO3-MoO3 interface leads to a large modulation of work function and to apparent doping in SrTiO3. The measured evolutions of electronic structure and upward band bending suggest that the growth of ultra-thin MoO3 layers is a powerful tool with which to modulate the surface energetics of SrTiO3, and this surface engineering approach could be generalized to other functional oxides.

Quantitative femtosecond charge transfer dynamics at organic/electrode interfaces studied by core-hole clock spectroscopy.

Organic semiconductor materials have important applications in organic electronics and other novel hybrid devices. In these devices, the transport of charge carriers across the interfaces between organic molecules and electrodes plays an important role in determining the device performance. Charge transfer dynamics at the organic/electrode interface usually occurs at the several femtoseconds timescale, and quantitative charge transfer dynamics data can been inferred using synchrotron-based core-hole clock (CHC) spectroscopy. In this research news, we have reviewed recent progress in the applications of CHC spectroscopy on the quantitative characterization of charge transfer dynamics at organic/electrode interfaces. By examining charge transfer dynamics at different types of interface, from weakly interacting van der Waals-type interfaces to interfaces with strong covalent bonds, we discuss a few factors that have been found to affect the charge transfer dynamics. We also review the application of CHC spectroscopy to quantify through-bonds and through-space charge transport in organic molecules.

Deterministic conversion between memory and threshold resistive switching via tuning the strong electron correlation.

Intensive investigations have been launched worldwide on the resistive switching (RS) phenomena in transition metal oxides due to both fascinating science and potential applications in next generation nonvolatile resistive random access memory (RRAM) devices. It is noteworthy that most of these oxides are strongly correlated electron systems, and their electronic properties are critically affected by the electron-electron interactions. Here, using NiO as an example, we show that rationally adjusting the stoichiometry and the associated defect characteristics enables controlled room temperature conversions between two distinct RS modes, i.e., nonvolatile memory switching and volatile threshold switching, within a single device. Moreover, from first-principles calculations and x-ray absorption spectroscopy studies, we found that the strong electron correlations and the exchange interactions between Ni and O orbitals play deterministic roles in the RS operations.

A synchrotron-based photoemission study of the MoO3∕Co interface.

The electronic structures at the MoO(3)∕Co interface were investigated using synchrotron-based ultraviolet and x-ray photoelectron spectroscopy. It was found that interfacial chemical reactions lead to the reduction of Mo oxidation states and the formation of Co-O bonds. These interfacial chemical reactions also induce a large interface dipole, which significantly increases the work function of the cobalt substrate. In addition, two interface states located at 1.0 and 2.0 eV below the Fermi level are identified. These two states overlap at film thickness of between 2-4 nm, which suggests the MoO(3) intermediate layer may facilitate ohmic charge transport.

Interplay of processing, morphological order, and charge-carrier mobility in polythiophene thin films deposited by different methods: comparison of spin-cast, drop-cast, and inkjet-printed films.

The dependence of morphology and polymer-chain orientation of regioregular poly(3-hexylthiophene) (rrP3HT) thin films on processing conditions have been widely studied. However, their possible variation across the film thickness direction remains largely unknown. We report here a marked difference in the optical dielectric (n,k) spectra between the top and bottom interfaces of spin-cast (sc) rrP3HT films deposited from chlorobenzene solutions. These spectra were obtained from reflection variable-angle spectroscopic ellipsometry using a self-consistent graded optical model with self-imposed Kramers-Krönig consistency. The top interface shows a red-shifted absorption that is characteristic of better order than at the bottom, across a wide range of film thicknesses. This disparity diminishes in drop-cast (dc) and multipass inkjet-printed (ijp) films, and disappears in amorphous films such as those of polystyrene and of a green-emitting phenyl-substituted poly(p-phenylenevinylene). The (n,k) spectra also reveal that crystallinity increases across sc < dc < ijp films. This is supported by cross section scanning electron microscopy of the cleaved edges and measurement of the microroughness of both the film interfaces. Furthermore, optical anisotropy decreases across sc > dc > ijp films. Finally, near-edge X-ray absorption fine structure spectroscopy also shows the frontier chains in ijp and dc films are more isotropically oriented than those in sc films. These results suggest that semicrystalline conjugated polymer films can be produced far from equilibrium. This explains the marked variation in their (opto)electronic properties between the top and bottom surfaces that has sometimes been found depending on the film deposition method. In particular, an unusually pronounced crystallization is induced by ijp. We label this marked ijp-induced crystallization the "ijp morphology", which appears to be general, as it is found also in single-inkjet-droplet films. It appears also to be responsible for the lower field-effect mobility measured for ijp films deposited on a variety of linear and circular electrode arrays. This however can fortuitously be reversed by annealing in solvent vapor. As all films were deposited in the low Peclet-number regime, we can rule out surface skin formation. We attribute the extensive crystallization to the non-uniform drying of picoliter droplets, further promoted by repeated film swelling-deswelling cycles in multipass-ijp films.

Surface transfer p-type doping of epitaxial graphene.

Epitaxial graphene thermally grown on 6H-SiC(0001) can be p-type doped via a novel surface transfer doping scheme by modifying the surface with the electron acceptor, tetrafluoro-tetracyanoquinodimethane (F4-TCNQ). Synchrotron-based high-resolution photoemission spectroscopy reveals that electron transfer from graphene to adsorbed F4-TCNQ is responsible for the p-type doping of graphene. This novel surface transfer doping scheme by surface modification with appropriate molecular acceptors represents a simple and effective method to nondestructively dope epitaxial graphene for future nanoelectronics applications.