Position of Carbonyl Group Affects Tribological Performance of Ester Friction Modifiers.

The tribological properties of lubricants can be effectively improved by the introduction of amphiphilic molecules, whose performance is largely affected by their polar head groups. In this work, the tribological performance in steel-steel contacts of two isomers, glycerol monostearate (GMS) and stearyl glycerate (SG), a glyceride and a glycerate, were investigated as organic friction modifiers (OFM) in hexadecane. SG exhibits a much lower friction coefficient and wear than GMS despite their similar structures. The same applies when comparing the performance of oleyl glycerate (OG) and its isomer, glycerol monooleate (GMO). Surface chemical analysis shows that SG forms a polar, carbon-based, tribofilm of around tens of nanometers thick, while GMS does not. This tribofilm shows low friction and robustness under nanotribology test, which may contribute to its superior performance at the macro-scale. The reason for this tribofilm formation can be due to the stronger adsorption of SG on the steel surface than that of GMS. The tribofilm formation can be stress-activated since lower friction and higher tribofilm coverage can be obtained under high load. This work offers insights into the lubrication mechanism of a novel OFM and provides strategies for OFM design.

Magnetoelectric Effect in Hydrogen Harvesting: Magnetic Field as a Trigger of Catalytic Reactions.

Magnetic fields have been regarded as an additional stimulus for electro- and photocatalytic reactions, but not as a direct trigger for catalytic processes. Multiferroic/magnetoelectric materials, whose electrical polarization and surface charges can be magnetically altered, are especially suitable for triggering and control of catalytic reactions solely with magnetic fields. Here, it is demonstrated that magnetic fields can be employed as an independent input energy source for hydrogen harvesting by means of the magnetoelectric effect. Composite multiferroic CoFe2 O4 -BiFeO3 core-shell nanoparticles act as catalysts for the hydrogen evolution reaction (HER), which is triggered when an alternating magnetic field is applied to an aqueous dispersion of the magnetoelectric nanocatalysts. Based on density functional calculations, it is proposed that the hydrogen evolution is driven by changes in the ferroelectric polarization direction of BiFeO3 caused by the magnetoelectric coupling. It is believed that the findings will open new avenues toward magnetically induced renewable energy harvesting.

Layer and spontaneous polarizations in perovskite oxides and their interplay in multiferroic bismuth ferrite.

We review the concept of surface charge, first, in the context of the polarization in ferroelectric materials and, second, in the context of layers of charged ions in ionic insulators. While the former is traditionally discussed in the ferroelectrics community and the latter in the surface science community, we remind the reader that the two descriptions are conveniently unified within the modern theory of polarization. In both cases, the surface charge leads to electrostatic instability-the so-called "polar catastrophe"-if it is not compensated, and we review the range of phenomena that arise as a result of different compensation mechanisms. We illustrate these concepts using the example of the prototypical multiferroic bismuth ferrite, BiFeO3, which is unusual in that its spontaneous ferroelectric polarization and the polarization arising from its layer charges can be of the same magnitude. As a result, for certain combinations of polarization orientation and surface termination, its surface charge is self-compensating. We use density functional calculations of BiFeO3 slabs and superlattices, analysis of high-resolution transmission electron micrographs, and examples from the literature to explore the consequences of this peculiarity.

On the happiness of ferroelectric surfaces and its role in water dissociation: The example of bismuth ferrite.

We investigate, using density functional theory, how the interaction between the ferroelectric polarization and the chemical structure of the (001) surfaces of bismuth ferrite influences the surface properties and reactivity of this material. A precise understanding of the surface behavior of ferroelectrics is necessary for their use in surface science applications such as catalysis as well as for their incorporation in microelectronic devices. Using the (001) surface of bismuth ferrite as a model system, we show that the most energetically favored surface geometries are combinations of surface termination and polarization direction that lead to uncharged stable surfaces. On the unfavorable charged surfaces, we explore the compensation mechanisms of surface charges provided by the introduction of point defects and adsorbates, such as water. Finally, we propose that the special surface properties of bismuth ferrite (001) could be used to produce an effective water splitting cycle through cyclic polarization switching.

In-situ monitoring of interface proximity effects in ultrathin ferroelectrics.

The development of energy-efficient nanoelectronics based on ferroelectrics is hampered by a notorious polarization loss in the ultrathin regime caused by the unscreened polar discontinuity at the interfaces. So far, engineering charge screening at either the bottom or the top interface has been used to optimize the polarization state. Yet, it is expected that the combined effect of both interfaces determines the final polarization state; in fact the more so the thinner a film is. The competition and cooperation between interfaces have, however, remained unexplored so far. Taking PbTiO3 as a model system, we observe drastic differences between the influence of a single interface and the competition and cooperation of two interfaces. We investigate the impact of these configurations on the PbTiO3 polarization when the interfaces are in close proximity, during thin-film synthesis in the ultrathin limit. By tailoring the interface chemistry towards a cooperative configuration, we stabilize a robust polarization state with giant polarization enhancement. Interface cooperation hence constitutes a powerful route for engineering the polarization in thin-film ferroelectrics towards improved integrability for oxide electronics in reduced dimension.

Interface and surface stabilization of the polarization in ferroelectric thin films.

Ferroelectric perovskites present a switchable spontaneous polarization and are promising energy-efficient device components for digital information storage. Full control of the ferroelectric polarization in ultrathin films of ferroelectric perovskites needs to be achieved in order to apply this class of materials in modern devices. However, ferroelectricity itself is not well understood in this nanoscale form, where interface and surface effects become particularly relevant and where loss of net polarization is often observed. In this work, we show that the precise control of the structure of the top surface and bottom interface of the thin film is crucial toward this aim. We explore the properties of thin films of the prototypical ferroelectric lead titanate (PbTiO3) on a metallic strontium ruthenate (SrRuO3) buffer using a combination of computational (density functional theory) and experimental (optical second harmonic generation) methods. We find that the polarization direction and strength are influenced by chemical and electronic processes occurring at the epitaxial interface and at the surface. The polarization is particularly sensitive to adsorbates and to surface and interface defects. These results point to the possibility of controlling the polarization direction and magnitude by engineering specific interface and surface chemistries.

Simulating Surfactant-Iron Oxide Interfaces: From Density Functional Theory to Molecular Dynamics.

Understanding the behavior of surfactant molecules on iron oxide surfaces is important for many industrial applications. Molecular dynamics (MD) simulations of such systems have been limited by the absence of a force field (FF), which accurately describes the molecule-surface interactions. In this study, interaction energies from density functional theory (DFT) + U calculations with a van der Waals functional are used to parameterize a classical FF for MD simulations of amide surfactants on iron oxide surfaces. The original FF, which was derived using mixing rules and surface Lennard-Jones (LJ) parameters developed for nonpolar molecules, was shown to significantly underestimate the adsorption energy and overestimate the equilibrium adsorption distance compared to DFT. Conversely, the optimized FF showed excellent agreement with the interaction energies obtained from DFT calculations for a wide range of surface coverages and molecular conformations near to and adsorbed on α-Fe2O3(0001). This was facilitated through the use of a Morse potential for strong chemisorption interactions, modified LJ parameters for weaker physisorption interactions, and adjusted partial charges for the electrostatic interactions. The original FF and optimized FF were compared in classical nonequilibrium molecular dynamics simulations of amide molecules confined between iron oxide surfaces. When the optimized FF was employed, the amide molecules were pulled closer to the surface and the orientation of the headgroups was more similar to that observed in the DFT calculations. The optimized FF proposed here facilitates classical MD simulations of anhydrous amide-iron oxide interfaces in which the interactions are representative of accurate DFT calculations.

Strain Relief during Ice Growth on a Hexagonal Template.

Heterogeneous ice nucleation at solid surfaces impacts many areas of science, from environmental processes, such as precipitation, to microbiological systems and food processing, but the microscopic mechanisms underpinning nucleation remain unclear. Discussion of ice growth has often focused around the role of the surface in templating the structure of water, forcing the first layer to adopt the registry of the underlying substrate rather than that of ice. To grow a thick ice film, water in the first few ice layers must accommodate this strain, but understanding how this occurs requires detailed molecular-scale information that is lacking. Here we combine scanning tunneling microscopy, low-energy electron diffraction, and work-function measurements with electronic structure calculations to investigate the initial stages of ice growth on a Pt alloy surface, having a lattice spacing 6% larger than ice. Although the first layer of water forms a strictly commensurate hexagonal network, this behavior does not extend to the second layer. Instead, water forms a 2D structure containing extended defect rows made from face-sharing pentamer and octamer rings. The defect rows allow the majority of second-layer water to remain commensurate with the solid surface while compensating lateral strain by increasing the water density close to that of an ice surface. The observation of octamer-pentamer rows in ice films formed on several surfaces suggests that the octamer-pentamer defect motif acts as a flexible strain relief mechanism in thin ice films, providing a mechanism that is not available during the growth of strained films in other materials, such as semiconductors.

Adsorption Behavior of Organic Molecules: A Study of Benzotriazole on Cu(111) with Spectroscopic and Theoretical Methods.

The adsorption of organic molecules on solid substrates is important to applications in fields such as catalysis, photovoltaics, corrosion inhibition, adhesion, and sensors. The molecular level description of the surface-molecule interaction and of the adsorption structures in these complex systems is crucial to understand their properties and function. Here, we present an investigation of one such system, benzotriazole (BTAH) on single-crystal Cu(111) in vacuum conditions. BTAH is the most widely used corrosion inhibitor for copper and thus a molecule of great industrial relevance. We show that the co-application of a wide range of spectroscopic techniques with theoretical methods provides unique insight in the description of the atomistic details of the adsorbed structures. Specifically, spectroscopic photoemission, absorption, and standing wave experiments combined with ab initio computational modeling allowed us to identify that benzotriazole forms overlayers of intact BTAH when deposited at low temperature, and it dissociates into BTA and H at room temperature and above. The dissociated molecule then forms complex structures of mixed chains and dimers of BTA bound to copper adatoms. Our work also reveals that copper adatoms at low concentrations, such as the theoretically predicted superstructures, cannot be resolved by means of current X-ray photoelectron spectroscopy as the modeled Cu 2p spectra are practically indistinguishable from those for a Cu surface without adatoms. Overall this study significantly deepens understanding of BTAH on Cu, a system studied for more than 50 years, and it highlights the benefits of combining spectroscopic and computational methods to obtain a complete picture of a complex adsorption system.

Water (Non-)Interaction with MoO3.

Molybdenum(VI) oxide (MoO3) is used in a number of technical processes such as gas filtration and heterogeneous catalysis. In these applications, the adsorption and dissociation of water on the surface can influence the chemistry of MoO3 and thus the course of heterogeneous reactions. We use ambient pressure X-ray photoelectron spectroscopy to study the interaction of water with a stoichiometric MoO3 surface and a MoO3 surface that features oxygen defects and hydroxyl groups. The experimental results are supported by density functional theory calculations. We show that on a stoichiometric MoO3(010) surface, where Mo sites are unavailable, water adsorption is strongly disfavored. However, the introduction of surface species, which can interact with the lone pairs on the water O atom, e.g., Mo5+ atoms or surface OH groups, promotes water adsorption. Dissociation of water is favored at unsaturated Mo sites, i.e., at oxygen vacancies, while water adsorbs molecularly at hydroxyl sites.

Piezoelectrically Enhanced Photocatalysis with BiFeO3 Nanostructures for Efficient Water Remediation.

Designing new catalysts that can efficiently utilize multiple energy sources can contribute to solving the current challenges of environmental remediation and increasing energy demands. In this work, we fabricated single-crystalline BiFeO3 (BFO) nanosheets and nanowires that can successfully harness visible light and mechanical vibrations and utilize them for degradation of organic pollutants. Under visible light both BFO nanostructures displayed a relatively slow reaction rate. However, under piezocatalysis both nanosheets and nanowires exhibited higher reaction rates in comparison with photocatalytic degradation. When both solar light and mechanical vibrations were used simultaneously, the reaction rates were elevated even further, with the BFO nanowires degrading 97% of RhB dye within 1 hr (k-value 0.058 min-1). The enhanced degradation under mechanical vibrations can be attributed to the promotion of charge separation caused by the internal piezoelectric field of BFO. BFO nanowires also exhibited good reusability and versatility toward degrading four different organic pollutants.

Chirality at two-dimensional surfaces: A perspective from small molecule alcohol assembly on Au(111).

The delicate balance between hydrogen bonding and van der Waals interactions determines the stability, structure, and chirality of many molecular and supramolecular aggregates weakly adsorbed on solid surfaces. Yet the inherent complexity of these systems makes their experimental study at the molecular level very challenging. In this quest, small alcohols adsorbed on metal surfaces have become a useful model system to gain fundamental insight into the interplay of such molecule-surface and molecule-molecule interactions. Here, through a combination of scanning tunneling microscopy and density functional theory, we compare and contrast the adsorption and self-assembly of a range of small alcohols from methanol to butanol on Au(111). We find that longer chained alcohols prefer to form zigzag chains held together by extended hydrogen bonded networks between adjacent molecules. When alcohols bind to a metal surface datively via one of the two lone electron pairs of the oxygen atom, they become chiral. Therefore, the chain structures are formed by a hydrogen-bonded network between adjacent molecules with alternating adsorbed chirality. These chain structures accommodate longer alkyl tails through larger unit cells, while the position of the hydroxyl group within the alcohol molecule can produce denser unit cells that maximize intermolecular interactions. Interestingly, when intrinsic chirality is introduced into the molecule as in the case of 2-butanol, the assembly changes completely and square packing structures with chiral pockets are observed. This is rationalized by the fact that the intrinsic chirality of the molecule directs the chirality of the adsorbed hydroxyl group meaning that heterochiral chain structures cannot form. Overall this study provides a general framework for understanding the effect of simple alcohol molecular adstructures on hydrogen bonded aggregates and paves the way for rationalizing 2D chiral supramolecular assembly.

Water-Ice Analogues of Polycyclic Aromatic Hydrocarbons: Water Nanoclusters on Cu(111).

Water has an incredible ability to form a rich variety of structures, with 16 bulk ice phases identified, for example, as well as numerous distinct structures for water at interfaces or under confinement. Many of these structures are built from hexagonal motifs of water molecules, and indeed, for water on metal surfaces, individual hexamers of just six water molecules have been observed. Here, we report the results of low-temperature scanning tunneling microscopy experiments and density functional theory calculations which reveal a host of new structures for water-ice nanoclusters when adsorbed on an atomically flat Cu surface. The H-bonding networks within the nanoclusters resemble the resonance structures of polycyclic aromatic hydrocarbons, and water-ice analogues of inene, naphthalene, phenalene, anthracene, phenanthrene, and triphenylene have been observed. The specific structures identified and the H-bonding patterns within them reveal new insight about water on metals that allows us to refine the so-called "2D ice rules", which have so far proved useful in understanding water-ice structures at solid surfaces.

Nonequilibrium Molecular Dynamics Simulations of Organic Friction Modifiers Adsorbed on Iron Oxide Surfaces.

For the successful development and application of lubricants, a full understanding of the nanoscale behavior of complex tribological systems is required, but this is difficult to obtain experimentally. In this study, we use nonequilibrium molecular dynamics (NEMD) simulations to examine the atomistic structure and friction properties of commercially relevant organic friction modifier (OFM) monolayers adsorbed on iron oxide surfaces and lubricated by a thin, separating layer of hexadecane. Specifically, acid, amide, and glyceride OFMs, with saturated and Z-unsaturated hydrocarbon tail groups, are simulated at various surface coverages and sliding velocities. At low and medium coverage, the OFMs form liquidlike and amorphous monolayers, respectively, which are significantly interdigitated with the hexadecane lubricant, resulting in relatively high friction coefficients. At high coverage, solidlike monolayers are formed for all of the OFMs, which, during sliding, results in slip planes between well-defined OFM and hexadecane layers, yielding a marked reduction in the friction coefficient. When present at equal surface coverage, OFMs with saturated and Z-unsaturated tail groups are found to yield similar structure and friction behavior. OFMs with glyceride head groups yield significantly lower friction coefficients than amide and particularly carboxylic acid head groups. For all of the OFMs and coverages simulated, the friction coefficient is found to increase linearly with the logarithm of sliding velocity; however, the gradient of this increase depends on the coverage. The structure and friction details obtained from these simulations agree well with experimental results and also shed light on the relative tribological performance of these OFMs through nanoscale structural variations. This has important implications in terms of the applicability of NEMD to aid the development of new formulations to control friction.

A Comparison of Classical Force-Fields for Molecular Dynamics Simulations of Lubricants.

For the successful development and application of lubricants, a full understanding of their complex nanoscale behavior under a wide range of external conditions is required, but this is difficult to obtain experimentally. Nonequilibrium molecular dynamics (NEMD) simulations can be used to yield unique insights into the atomic-scale structure and friction of lubricants and additives; however, the accuracy of the results depend on the chosen force-field. In this study, we demonstrate that the use of an accurate, all-atom force-field is critical in order to; (i) accurately predict important properties of long-chain, linear molecules; and (ii) reproduce experimental friction behavior of multi-component tribological systems. In particular, we focus on n-hexadecane, an important model lubricant with a wide range of industrial applications. Moreover, simulating conditions common in tribological systems, i.e., high temperatures and pressures (HTHP), allows the limits of the selected force-fields to be tested. In the first section, a large number of united-atom and all-atom force-fields are benchmarked in terms of their density and viscosity prediction accuracy of n-hexadecane using equilibrium molecular dynamics (EMD) simulations at ambient and HTHP conditions. Whilst united-atom force-fields accurately reproduce experimental density, the viscosity is significantly under-predicted compared to all-atom force-fields and experiments. Moreover, some all-atom force-fields yield elevated melting points, leading to significant overestimation of both the density and viscosity. In the second section, the most accurate united-atom and all-atom force-field are compared in confined NEMD simulations which probe the structure and friction of stearic acid adsorbed on iron oxide and separated by a thin layer of n-hexadecane. The united-atom force-field provides an accurate representation of the structure of the confined stearic acid film; however, friction coefficients are consistently under-predicted and the friction-coverage and friction-velocity behavior deviates from that observed using all-atom force-fields and experimentally. This has important implications regarding force-field selection for NEMD simulations of systems containing long-chain, linear molecules; specifically, it is recommended that accurate all-atom potentials, such as L-OPLS-AA, are employed.

Understanding corrosion inhibition with van der Waals DFT methods: the case of benzotriazole.

The corrosion of materials is an undesirable and costly process affecting many areas of technology and everyday life. As such, considerable effort has gone into understanding and preventing it. Organic molecule based coatings can in certain circumstances act as effective corrosion inhibitors. Although they have been used to great effect for more than sixty years, how they function at the atomic-level is still a matter of debate. In this work, computer simulation approaches based on density functional theory are used to investigate benzotriazole (BTAH), one of the most widely used and studied corrosion inhibitors for copper. In particular, the structures formed by protonated and deprotonated BTAH molecules on Cu(111) have been determined and linked to their inhibiting properties. It is found that hydrogen bonding, van der Waals interactions and steric repulsions all contribute in shaping how BTAH molecules adsorb, with flat-lying structures preferred at low coverage and upright configurations preferred at high coverage. The interaction of the dehydrogenated benzotriazole molecule (BTA) with the copper surface is instead dominated by strong chemisorption via the azole moiety with the aid of copper adatoms. Structures of dimers or chains are found to be the most stable structures at all coverages, in good agreement with scanning tunnelling microscopy results. Benzotriazole thus shows a complex phase behaviour in which van der Waals forces play an important role and which depends on coverage and on its protonation state and all of these factors feasibly contribute to its effectiveness as a corrosion inhibitor.

Traction and nonequilibrium phase behavior of confined sheared liquids at high pressure.

Nonequilibrium molecular dynamics simulations of confined model liquids under pressure and sheared by the relative sliding of the boundary walls have been carried out. The relationship between the time-dependent traction coefficient, µ(t), and the state of internal structure of the film is followed from commencement of shear for various control parameters, such as applied load, global shear rate, and solid-liquid atom interaction parameters. Phase diagrams, velocity and temperature profiles, and traction coefficient diagrams are analyzed for pure Lennard-Jones (LJ) liquids and a binary LJ mixture. A single component LJ liquid is found to form semicrystalline arrangements with high-traction coefficients, and stick-slip behavior is observed for high pressures and low-shear velocities, which is shown to involve periodic deformation and stress release of the wall atoms and slip in the solid-liquid boundary region. A binary mixture, which discourages crystallization, gives a more classical tribological response with the larger atoms preferentially adsorbing commensurate with the wall. The results obtained are analyzed in the context of tribology: the binary mixture behaves like a typical lubricant, whereas the monatomic system behaves like a traction fluid. It is discussed how this type of simulation can give insights on the tribological behavior of realistic systems.

2D supramolecular assemblies of benzene-1,3,5-triyl-tribenzoic acid: temperature-induced phase transformations and hierarchical organization with macrocyclic molecules.

Two-dimensional supramolecular honeycomb networks with cavities of an internal diameter of 2.95 nm were formed by the self-assembly of 4,4',4' '-benzene-1,3,5-triyl-tribenzoic acid (BTA) on a Ag(111) surface at room temperature. Annealing to higher temperatures resulted in two sequential phase transformations into closer-packed supramolecular arrangements. The phase transformations are associated with stepwise deprotonation of the carboxylic acid groups. The voids of the honeycomb network of BTA have a suitable size for the construction of hierarchical structures with guest molecules. Single molecules of the macrocyclic compound mt-33 were successfully confined inside 2D nanocavities of the honeycomb networks and released when the phase was transformed to the close-packed structure.