RESUMEN
Semiconductor nanowires are believed to play a crucial role for future applications in electronics, spintronics and quantum technologies. A potential candidate is HgTe but its sensitivity to nanofabrication processes restrain its development. A way to circumvent this obstacle is the selective area growth technique. Here, in-plane HgTe nanostructures are grown thanks to selective area molecular beam epitaxy on a semi-insulating CdTe substrate covered with a patterned SiO2mask. The shape of these nanostructures is defined by the in-plane orientation of the mask aperture along the <110>, <1-10>, or <100> direction, the deposited thickness, and the growth temperature. Several micron long in-plane nanowires can be achieved as well as more complex nanostructures such as networks, diamond structures or rings. A good selectivity is achieved with very little parasitic growth on the mask even for a growth temperature as low as 140°C and growth rate up to 0.5 ML/s. For <110> oriented nanowires, the center of the nanostructure exhibits a trapezoidal shape with {111}B facets and two grains on the sides, while <1-10> oriented nanowires show {111}A facets with adatoms accumulation on the sides of the top surface. Transmission electron microscopy observations reveal a continuous epitaxial relation between the CdTe substrate and the HgTe nanowire. Measurements of the resistance with four-point scanning tunneling microscopy indicates a good electrical homogeneity along the main NW axis and a thermally activated transport. This growth method paves the way toward the fabrication of complex HgTe-based nanostructures for electronic transport measurements.
RESUMEN
X-ray ptychography and ptychographic computed tomography have seen a rapid rise since the advent of fourth-generation synchrotrons with a high degree of coherent radiation. In addition to quantitative multiscale structural analysis, ptychography with spectral capabilities has been developed, allowing for spatial-localized multiscale structural and spectral information of samples. The SWING beamline of Synchrotron SOLEIL has recently developed a nanoprobe setup where the endstation's first spectral and resonant ptychographic measurements have been successfully conducted. A metallic nickel wire sample was measured using 2D spectral ptychography in XANES mode and resonant ptychographic tomography. From the 2D spectral ptychography measurements, the spectra of the components of the sample's complex-valued refractive index, δ and ß, were extracted, integrated along the sample thickness. By performing resonance ptychographic tomography at two photon energies, 3D maps of the refractive index decrement, δ, were obtained at the Ni K-edge energy and another energy above the edge. These maps allowed the detection of impurities in the Ni wire. The significance of accounting for the atomic scattering factor is demonstrated in the calculation of electron density near a resonance through the use of the δ values. These results indicate that at the SWING beamline it is possible to conduct state-of-the-art spectral and resonant ptychography experiments using the nanoprobe setup.
RESUMEN
X-ray ptychography is a coherent diffraction imaging technique based on acquiring multiple diffraction patterns obtained through the illumination of the sample at different partially overlapping probe positions. The diffraction patterns collected are used to retrieve the complex transmittivity function of the sample and the probe using a phase retrieval algorithm. Absorption or phase contrast images of the sample as well as the real and imaginary parts of the probe function can be obtained. Furthermore, X-ray ptychography can also provide spectral information of the sample from absorption or phase shift images by capturing multiple ptychographic projections at varying energies around the resonant energy of the element of interest. However, post-processing of the images is required to extract the spectra. To facilitate this, ProSPyX, a Python package that offers the analysis tools and a graphical user interface required to process spectral ptychography datasets, is presented. Using the PyQt5 Python open-source module for development and design, the software facilitates extraction of absorption and phase spectral information from spectral ptychographic datasets. It also saves the spectra in file formats compatible with other X-ray absorption spectroscopy data analysis software tools, streamlining integration into existing spectroscopic data analysis pipelines. To illustrate its capabilities, ProSPyX was applied to process the spectral ptychography dataset recently acquired on a nickel wire at the SWING beamline of the SOLEIL synchrotron.
Asunto(s)
Trasplante de Células Madre de Sangre Periférica , Leucemia-Linfoma Linfoblástico de Células Precursoras , Adulto , Humanos , Proteínas de Fusión bcr-abl/genética , Leucemia-Linfoma Linfoblástico de Células Precursoras/genética , Leucemia-Linfoma Linfoblástico de Células Precursoras/terapia , Cromosoma FiladelfiaRESUMEN
The public French Cord Blood Banks Network was established in 1999 with the objective of standardizing the practices governing umbilical cord blood (UCB) banking in France. The Network adopted a strategy to optimize its inventory and improve the quality of its banked units based on a quality improvement process using outcome data regularly provided by Eurocord. This study aimed to describe the results, over 10 years, of UCBT facilitated by a national network that used the same criteria of UCB collection and banking and to assess how modifications of banking criteria and unit selection might influence transplant outcomes. Nine hundred and ninety-nine units (593 single-unit and 203 double-unit grafts) were released by the Network to transplant 796 patients with malignant (83%) and non-malignant (17%) diseases. Median cell dose exceeded 3.5 × 107 TNC/kg in 86%. There was a trend to select units more recently collected and with higher cell dose. Neutrophil engraftment was 88.2% (85.7-90.7) and 79.3% (72.6-86.5) respectively for malignant and non-malignant diseases with a trend to faster recovery with higher cell doses. The respective 3-year transplant-related mortality were 31.1% (27.5-35.1) and 34.3% (27.0-43.5). OS was 49% ± 4 in malignant and 62% ± 4 in non-malignant disorders. In multivariate analysis, cell dose was the only unit-related factor associated with outcomes. Our results reflect the benefit on clinical outcomes of the strategy adopted by the Network to bank units with higher cell counts.
Asunto(s)
Trasplante de Células Madre de Sangre del Cordón Umbilical , Trasplante de Células Madre Hematopoyéticas , Bancos de Sangre , Trasplante de Médula Ósea , Sangre Fetal , HumanosRESUMEN
CD34+ immunomagnetic positive selection allows for CD34+ hematopoietic progenitors separation from CD3+ lymphocytes subsets, usually from an apheresis product collected from a previously mobilized donor. This T-cell depleted stem cell graft is primarily intended for rare cases (around 2% of allotransplanted patients in France) of severe, persistent, symptomatic bi- or tri-cytopenia post-allotransplantation, in order to allow for hematologic reconstitution without increasing the risk of GvHD occurrence. Although semi-manual and complex, the process is of sufficient robustness to consistently generate a cellular product with distinctive features and specifications, based on iterative in-process quality controls, that are discussed within these guidelines.
Asunto(s)
Antígenos CD34 , Células Madre Hematopoyéticas/citología , Separación Inmunomagnética/métodos , Separación Inmunomagnética/normas , Control de Calidad , Citaféresis , Enfermedad Injerto contra Huésped/prevención & control , Células Madre Hematopoyéticas/inmunología , Humanos , Pancitopenia/terapia , Sociedades MédicasRESUMEN
During barrel aging, wines and spirits undergo sensory changes as a result of the release of aroma and taste molecules. Among the nonvolatile compounds, various coumarins have already been identified in oak wood but their sensory role remained unclear. In this study, the presence of coumarins in oak wood extract, wine, and spirits was first assessed by targeted screening. Fraxetin was identified for the first time in these matrices. After development and validation of a liquid chromatography-high-resolution mass spectrometry quantitation method, esculetin, scopoletin, fraxetin, umbelliferone, 4-methylumbelliferone, and coumarin were assayed in various wines and spirits. The concentrations measured were generally below the gustatory detection thresholds determined in wines and spirits. Nevertheless, by adding a mixture of coumarins in wines and spirits, a significant increase in bitterness was observed, thus demonstrating their potential contribution to the taste of wines and spirits through perceptive interactions.
Asunto(s)
Bebidas Alcohólicas/análisis , Cumarinas/análisis , Manipulación de Alimentos/instrumentación , Quercus/química , Gusto , Vino/análisis , Cromatografía Líquida de Alta Presión , Humanos , Espectrometría de Masas , Odorantes/análisis , Madera/químicaRESUMEN
We present the regional professional network to support the Renal Epidemiology Information Network (REIN) registry in maintaining high quality data production and information analyses in Ile-De-France region. The network is based on a long term partnership between the nephrologists and a regional methodology support unit. It integrates clinical research assistants for data quality control. We also present organizational methods on maintaining the registry and enhancing information analyses and automating analyses reports.
Asunto(s)
Sistema de Registros , Exactitud de los Datos , Francia , Servicios de InformaciónRESUMEN
Nanowire antennas embedding single quantum dots (QDs) have recently emerged as a versatile solid-state platform for quantum optics. Within the nanowire section, the emitter position simultaneously determines the strength of the light-matter interaction, as well as the coupling to potential decoherence channels. Therefore, to quantitatively understand device performance and guide future optimization, it is highly desirable to map the emitter position with an accuracy much smaller than the waveguide diameter, on the order of a few hundreds of nanometers. We introduce here a nondestructive, all-optical mapping technique that exploits the QD emission into two guided modes with different transverse profiles. These two modes are fed by the same emitter and thus interfere. The resulting intensity pattern, which is highly sensitive to the emitter position, is resolved in the far-field using Fourier microscopy. We demonstrate this technique on a standard microphotoluminescence setup and map the position of individual QDs in a nanowire antenna with a spatial resolution of ±10 nm. This work opens important perspectives for the future development of light-matter interfaces based on nanowire antennas. Beyond single-QD devices, it will also provide a valuable tool for the investigation of collective effects that imply several emitters coupled to an optical waveguide.
RESUMEN
A new kind of nanodevice that acts like tweezers through remote actuation by an external magnetic field is designed. Such device is meant to mechanically grab micrometric objects. The nanotweezers are built by using a top-down approach and are made of two parallelepipedic microelements, at least one of them being magnetic, bound by a flexible nanohinge. The presence of an external magnetic field induces a torque on the magnetic elements that competes with the elastic torque provided by the nanohinge. A model is established in order to evaluate the values of the balanced torques as a function of the tweezers opening angles. The results of the calculations are confronted to the expected values and validate the overall working principle of the magnetic nanotweezers.
RESUMEN
A flexible nitride p-n photodiode is demonstrated. The device consists of a composite nanowire/polymer membrane transferred onto a flexible substrate. The active element for light sensing is a vertical array of core/shell p-n junction nanowires containing InGaN/GaN quantum wells grown by MOVPE. Electron/hole generation and transport in core/shell nanowires are modeled within nonequilibrium Green function formalism showing a good agreement with experimental results. Fully flexible transparent contacts based on a silver nanowire network are used for device fabrication, which allows bending the detector to a few millimeter curvature radius without damage. The detector shows a photoresponse at wavelengths shorter than 430 nm with a peak responsivity of 0.096 A/W at 370 nm under zero bias. The operation speed for a 0.3 × 0.3 cm2 detector patch was tested between 4 Hz and 2 kHz. The -3 dB cutoff was found to be â¼35 Hz, which is faster than the operation speed for typical photoconductive detectors and which is compatible with UV monitoring applications.
RESUMEN
We report the first demonstration of flexible white phosphor-converted light emitting diodes (LEDs) based on p-n junction core/shell nitride nanowires. GaN nanowires containing seven radial In0.2Ga0.8N/GaN quantum wells were grown by metal-organic chemical vapor deposition on a sapphire substrate by a catalyst-free approach. To fabricate the flexible LED, the nanowires are embedded into a phosphor-doped polymer matrix, peeled off from the growth substrate, and contacted using a flexible and transparent silver nanowire mesh. The electroluminescence of a flexible device presents a cool-white color with a spectral distribution covering a broad spectral range from 400 to 700 nm. Mechanical bending stress down to a curvature radius of 5 mm does not yield any degradation of the LED performance. The maximal measured external quantum efficiency of the white LED is 9.3%, and the wall plug efficiency is 2.4%.
RESUMEN
We introduce a calibration method to quantify the impact of external mechanical stress on the emission wavelength of distinct quantum dots (QDs). Specifically, these emitters are integrated in a cross-section of a semiconductor core wire and experience a longitudinal strain that is induced by an amorphous capping shell. Detailed numerical simulations show that, thanks to the shell mechanical isotropy, the strain in the core is uniform, which enables a direct comparison of the QD responses. Moreover, the core strain is determined in situ by an optical measurement, yielding reliable values for the QD emission tuning slope. This calibration technique is applied to self-assembled InAs QDs submitted to incremental elongation along their growth axis. In contrast to recent studies conducted on similar QDs submitted to a uniaxial stress perpendicular to the growth direction, optical spectroscopy reveals up to ten times larger tuning slopes, with a moderate dispersion. These results highlight the importance of the stress direction to optimize the QD optical shift, with general implications, both in static and dynamic regimes. As such, they are in particular relevant for the development of wavelength-tunable single-photon sources or hybrid QD opto-mechanical systems.
Asunto(s)
Trasplante de Células Madre Hematopoyéticas/métodos , Hepacivirus/aislamiento & purificación , Hepatitis C/diagnóstico , Leucemia Mieloide Aguda/terapia , ARN Viral/aislamiento & purificación , Uridina Monofosfato/análogos & derivados , Adulto , Femenino , Humanos , Masculino , Persona de Mediana Edad , Hermanos , Sofosbuvir , Donantes de Tejidos , Uridina Monofosfato/uso terapéuticoRESUMEN
The purpose of this study was to assess the usefulness of real-time PCR as a quantitative, highly reproducible, and sensitive method, for detecting and quantifying p53 recombinant adenovirus in biological samples from cancer patients receiving injections of Ad5CMV-p53. The dynamic range of this real-time PCR-based assay was wide (at least five orders of magnitude). Our assay used an internal positive control in the same PCR tube that is capable of detecting residual PCR inhibitors. Serial spiked samples in plasma with known quantities of Ad5CMV-p53 were evaluated. The minimum detection limit was 2 pfu per PCR (approximately 50 pfu per ml of plasma) and the quantification values were reproducible. A total of 2069 controls tested with 1780 plasma samples from 286 patients enrolled in gene therapy trials using Ad5CMV-p53 were investigated. Using calibrators to adjust the quantitation value, the results confirmed the good performance of the assay. In conclusion, the high sensitivity, simplicity and reproducibility of the real-time Ad5CMV-p53 assay, allowing screening of large numbers of samples, combined with its wide dynamic range, make this method particularly suitable for monitoring gene therapy trials.