The adsorption of nitrobenzene over an alumina-supported palladium catalyst: an infrared spectroscopic study.

As part of an on-going programme of development of an aniline synthesis catalyst suitable for operation at elevated temperatures, the geometry of the adsorption complex for nitrobenzene on a 5 wt% Pd/Al2O3 catalyst is investigated by infrared (IR) spectroscopy. Via an appreciation of the reduced site symmetry resulting from adsorption, application of the metal surface selection rule, and observation of in-plane modes only, the adsorption complex (Pd-nitrobenzene) at 28 °C is assigned as occurring vertically or tilted with respect to the metal surface, adopting Csσv(yz) symmetry. Moreover, adsorption occurs via a single Pd-O bond. Single molecule DFT calculations and simulated IR spectra assist vibrational assignments but indicate a parallel adsorption geometry to be energetically favourable. The contradiction between calculated and observed structures is attributed to the DFT calculations corresponding to an isolated molecule adsorption complex, while IR spectra relate to multi molecule adsorption that is encountered during sustained catalytic turnover. Residual hydrogen from the catalyst reduction stage leads to aniline formation on the Pd surface at low nitrobenzene coverages but, on increasing nitrobenzene exposure, the aniline is forced on to the alumina support. A reaction scheme is proposed whereby the nitrobenzene adsorption geometry is inherently linked to the high aniline selectivity observed for Pd/Al2O3 catalysts.

Operando XAFS investigation on the effect of ash deposition on three-way catalyst used in gasoline particulate filters and the effect of the manufacturing process on the catalytic activity.

Platinum group metals such as palladium and rhodium based catalysts are currently being implemented in gasoline particulate filter (GPF) autoexhaust after treatment systems. However, little is known about how the trapped particulate matter, such as the incombustible ash, interacts with the catalyst and so may affect its performance. Thisoperandostudy follows the evolution of the Pd found in two different model GPF systems: one containing ash components extracted from a GPF and another from a catalyst washcoat prior to adhesion onto the GPF. We show that the catalytic activity of the two systems vary when compared with a 0 g ash containing GPF. Compared to the 0 g ash sample the 20 g ash containing sample had a higher CO light off temperature, in addition, an oscillation profile for CO, CO2and O2was observed, which is speculated to be a combination of CO oxidation, C deposition via a Boudouard reaction and further partial oxidation of the deposited species to CO. During the ageing procedure the washcoat sample reduces NO at a lower temperature than the 0 g ash sample. However, post ageing the 0 g ash sample recovers and both samples reduce NO at 310 °C. In comparison, the 20 g ash GPF sample maintains a higher NO reduction temperature of 410 °C post ageing, implying that the combination of high temperature ageing and presence of ash has an irreversible negative effect on catalyst performance.

Spatial Profiling of a Pd/Al2O3 Catalyst during Selective Ammonia Oxidation.

The utilization of operando spectroscopy has allowed us to watch the dynamic nature of supported metal nanoparticles. However, the realization that subtle changes to environmental conditions affect the form of the catalyst necessitates that we assess the structure of the catalyst across the reactant/product gradient that exists across a fixed bed reactor. In this study, we have performed spatial profiling of a Pd/Al2O3 catalyst during NH3 oxidation, simultaneously collecting mass spectrometry and X-ray absorption spectroscopy data at discrete axial positions along the length of the catalyst bed. The spatial analysis has provided unique insights into the structure-activity relationships that govern selective NH3 oxidation-(i) our data is consistent with the presence of PdN x after the spectroscopic signatures for bulk PdN x disappear and that there is a direct correlation to the presence of this structure and the selectivity toward N2; (ii) at high temperatures, ≥400 °C, we propose that there are two simultaneous reaction pathways-the oxidation of NH3 to NO x by PdO and the subsequent catalytic reduction of NO x by NH3 to produce N2. The results in this study confirm the structural and catalytic diversity that exists during catalysis and the need for such an understanding if improvements to important emission control technologies, such as the selective catalytic oxidation of NH3, are to be made.

Design, Identification, and Evolution of a Surface Ruthenium(II/III) Single Site for CO Activation.

RuII compounds are widely used in catalysis, photocatalysis, and medical applications. They are usually obtained in a reductive environment as molecular O2 can oxidize RuII to RuIII and RuIV . Here we report the design, identification and evolution of an air-stable surface [bipy-RuII (CO)2 Cl2 ] site that is covalently mounted onto a polyphenylene framework. Such a RuII site was obtained by reduction of [bipy-RuIII Cl4 ]- with simultaneous ligand exchange from Cl- to CO. This structural evolution was witnessed by a combination of in situ X-ray and infrared spectroscopy studies. The [bipy-RuII (CO)2 Cl2 ] site enables oxidation of CO with a turnover frequency of 0.73×10-2  s-1 at 462 K, while the RuIII site is completely inert. This work contributes to the study of structure-activity relationship by demonstrating a practical control over both geometric and electronic structures of single-site catalysts at molecular level.

Adsorption and activation of molecular oxygen over atomic copper(I/II) site on ceria.

Supported atomic metal sites have discrete molecular orbitals. Precise control over the energies of these sites is key to achieving novel reaction pathways with superior selectivity. Here, we achieve selective oxygen (O2) activation by utilising a framework of cerium (Ce) cations to reduce the energy of 3d orbitals of isolated copper (Cu) sites. Operando X-ray absorption spectroscopy, electron paramagnetic resonance and density-functional theory simulations are used to demonstrate that a [Cu(I)O2]3- site selectively adsorbs molecular O2, forming a rarely reported electrophilic η2-O2 species at 298 K. Assisted by neighbouring Ce(III) cations, η2-O2 is finally reduced to two O2-, that create two Cu-O-Ce oxo-bridges at 453 K. The isolated Cu(I)/(II) sites are ten times more active in CO oxidation than CuO clusters, showing a turnover frequency of 0.028 ± 0.003 s-1 at 373 K and 0.01 bar PCO. The unique electronic structure of [Cu(I)O2]3- site suggests its potential in selective oxidation.

Redox-Active Hybrid Polyoxometalate-Stabilised Gold Nanoparticles.

We report the design and preparation of multifunctional hybrid nanomaterials through the stabilization of gold nanoparticles with thiol-functionalised hybrid organic-inorganic polyoxometalates (POMs). The covalent attachment of the hybrid POM forms new nanocomposites that are stable at temperatures and pH values which destroy analogous electrostatically functionalised nanocomposites. Photoelectrochemical analysis revealed the unique photochemical and redox properties of these systems.

Synergistic ultraviolet and visible light photo-activation enables intensified low-temperature methanol synthesis over copper/zinc oxide/alumina.

Although photoexcitation has been employed to unlock the low-temperature equilibrium regimes of thermal catalysis, mechanism underlining potential interplay between electron excitations and surface chemical processes remains elusive. Here, we report an associative zinc oxide band-gap excitation and copper plasmonic excitation that can cooperatively promote methanol-production at the copper-zinc oxide interfacial perimeter of copper/zinc oxide/alumina (CZA) catalyst. Conversely, selective excitation of individual components only leads to the promotion of carbon monoxide production. Accompanied by the variation in surface copper oxidation state and local electronic structure of zinc, electrons originating from the zinc oxide excitation and copper plasmonic excitation serve to activate surface adsorbates, catalysing key elementary processes (namely formate conversion and hydrogen molecule activation), thus providing one explanation for the observed photothermal activity. These observations give valuable insights into the key elementary processes occurring on the surface of the CZA catalyst under light-heat dual activation.

In situ K-edge X-ray absorption spectroscopy of the ligand environment of single-site Au/C catalysts during acetylene hydrochlorination.

The replacement of HgCl2/C with Au/C as a catalyst for acetylene hydrochlorination represents a significant reduction in the environmental impact of this industrial process. Under reaction conditions atomically dispersed cationic Au species are the catalytic active site, representing a large-scale application of heterogeneous single-site catalysts. While the metal nuclearity and oxidation state under operating conditions has been investigated in catalysts prepared from aqua regia and thiosulphate, limited studies have focused on the ligand environment surrounding the metal centre. We now report K-edge soft X-ray absorption spectroscopy of the Cl and S ligand species used to stabilise these isolated cationic Au centres in the harsh reaction conditions. We demonstrate the presence of three distinct Cl species in the materials; inorganic Cl-, Au-Cl, and C-Cl and how these species evolve during reaction. Direct evidence of Au-S interactions is confirmed in catalysts prepared using thiosulfate precursors which show high stability towards reduction to inactive metal nanoparticles. This stability was clear during gas switching experiments, where exposure to C2H2 alone did not dramatically alter the Au electronic structure and consequently did not deactivate the thiosulfate catalyst.

Retroileal anastomosis in hand-assisted laparoscopic left colectomy: experience at a single institution.

BACKGROUND: Left hemicolectomy and complicated sigmoid colectomy require an anastomosis between the transverse colon and rectum. Generous mobilization will typically allow the colon to reach to the rectum. However, despite full mobilization of the splenic flexure and extensive work on the mesentery, there are cases in which reach to the pelvis is still an issue. Retroileal routing of the colon is one technique for overcoming such a reach problem and achieving a tension-free anastomosis. Performing retroileal routing using laparoscopic techniques has been reported rarely, and to date, there are no data on this technique when performed in a hand-assisted laparoscopic fashion. This study aimed to describe the feasibility of doing a retroileal routing using a hand-assisted laparoscopic technique. METHODS: This was a retrospective chart review of patients who underwent a colon or rectal resection, either open or laparoscopic, with a pelvic anastomosis, by a single colorectal surgeon at an academic institution between 2008 and 2015 with a focus on the immediate and long-term postoperative complications, estimated blood loss, and operating room time for patients having an operation that included retroileal routing for construction of a colorectal anastomosis. RESULTS: A total of 340 patients fit inclusion criteria and of these, 13 underwent hand-assisted laparoscopic procedures with retroileal routing of the proximal colon to the colorectal anastomosis. Postoperative morbidity included intubation for CO2 retention in one patient and a RLL effusion in another patient; there were no anastomotic leaks. Long-term morbidities included two ventral hernias at 2 years postoperatively. Mean operating room time was 208 min. There were no 30- or 90-day mortalities. CONCLUSIONS: Hand-assisted laparoscopic retroileal routing is a feasible and safe technique in accomplishing a tension-free colorectal anastomosis when proximal colon length makes standard routing of the colon to the rectum an issue.

Author Correction: The rapid electrochemical activation of MoTe2 for the hydrogen evolution reaction.

An amendment to this paper has been published and can be accessed via a link at the top of the paper.

The rapid electrochemical activation of MoTe2 for the hydrogen evolution reaction.

The electrochemical generation of hydrogen is a key enabling technology for the production of sustainable fuels. Transition metal chalcogenides show considerable promise as catalysts for this reaction, but to date there are very few reports of tellurides in this context, and none of these transition metal telluride catalysts are especially active. Here, we show that the catalytic performance of metallic 1T'-MoTe2 is improved dramatically when the electrode is held at cathodic bias. As a result, the overpotential required to maintain a current density of 10 mA cm-2 decreases from 320 mV to just 178 mV. We show that this rapid and reversible activation process has its origins in adsorption of H onto Te sites on the surface of 1T'-MoTe2. This activation process highlights the importance of subtle changes in the electronic structure of an electrode material and how these can influence the subsequent electrocatalytic activity that is displayed.

Synthesis, characterisation and water-gas shift activity of nano-particulate mixed-metal (Al, Ti) cobalt oxides.

The formation of mixed-metal cobalt oxides, representing potential metal-support compounds for cobalt-based catalysts, has been observed at high conversion levels in the Fischer-Tropsch synthesis over metal oxide-supported cobalt catalysts. An often observed increase in the carbon dioxide selectivity at Fischer-Tropsch conversion levels above 80% has been suggested to be associated to the formation of water-gas shift active oxidic cobalt species. Mixed-metal cobalt oxides, namely cobalt aluminate and cobalt titanate, were therefore synthesised and tested for potential catalytic activity in the water-gas shift reaction. We present a preparation route for amorphous mixed-metal oxides via thermal treatment of metal precursors in benzyl alcohol. Calcination of the as prepared nanoparticles results in highly crystalline phases. The nano-particulate mixed-metal cobalt oxides were thoroughly analysed by means of X-ray diffraction, Raman spectroscopy, temperature-programmed reduction, X-ray absorption near edge structure spectroscopy, extended X-ray absorption fine structure, and high-resolution scanning transmission electron microscopy. This complementary characterisation of the synthesised materials allows for a distinct identification of the phases and their properties. The cobalt aluminate prepared has a cobalt-rich composition (Co1+xAl2-xO4) with a homogeneous atomic distribution throughout the nano-particulate structures, while the perovskite-type cobalt titanate (CoTiO3) features cobalt-lean smaller particles associated with larger ones with an increased concentration of cobalt. The cobalt aluminate prepared showed no water-gas shift activity in the medium-shift temperature range, while the cobalt titanate sample catalysed the conversion of water and carbon monoxide to hydrogen and carbon dioxide after an extended activation period. However, this perovskite underwent vast restructuring forming metallic cobalt, a known catalyst for the water-gas shift reaction at temperatures exceeding typical conditions for the cobalt-based Fischer-Tropsch synthesis, and anatase-TiO2. The partial reduction of the mixed-metal oxide and segregation was identified by means of post-run characterisation using X-ray diffraction, Raman spectroscopy, and transmission electron microscopy energy-dispersive spectrometry.

Shape-persistent porous organic cage supported palladium nanoparticles as heterogeneous catalytic materials.

Porous Organic Cages (POCs) are an emerging class of self-assembling, porous materials with novel properties. They offer a key advantage over other porous materials in permitting facile solution processing and re-assembly. The combination of POCs with metal nanoparticles (NPs) unlocks applications in the area of catalysis. In this context, POCs can function as both the template of ultra-small NPs and a porous, but reprocessable, heterogeneous catalyst support. Here, we demonstrate the synthesis of ultra-small Pd NPs with an imine linked POC known as 'CC3', and show that hydrogen gas can be used to form metallic NPs at ∼200 °C without the reduction of the organic cage (and the accompanying, unwanted loss of crystallinity). The resulting materials are characterized using a range of techniques (including powder diffraction, scanning transmission electron microscopy and synchrotron X-ray absorption spectroscopy) and shown to be recrystallizable following dissolution in organic solvent. Their catalytic efficacy is demonstrated using the widely studied carbon monoxide oxidation reaction. This demonstration paves the way for using ultra-small NPs synthesized with POCs as solution-processable, self-assembling porous catalytic materials.

Evidence for tetranuclear bis-µ-oxo cubane species in molecular iridium-based water oxidation catalysts from XAS analysis.

The structure of a highly active pyridine-alkoxide iridium water oxidation catalyst (WOC) is examined by X-ray absorption spectroscopy (XAS). A detailed comparison with IrO2 points to a rigid molecular unit of low nuclearity, with the best analysis suggesting a novel tetrameric iridium-oxo cubane as the resting state.

Impact of Nanoparticle-Support Interactions in Co3O4/Al2O3 Catalysts for the Preferential Oxidation of Carbon Monoxide.

Different supporting procedures were followed to alter the nanoparticle-support interactions (NPSI) in two Co3O4/Al2O3 catalysts, prepared using the reverse micelle technique. The catalysts were tested in the dry preferential oxidation of carbon monoxide (CO-PrOx) while their phase stability was monitored using four complementary in situ techniques, viz., magnet-based characterization, PXRD, and combined XAS/DRIFTS, as well as quasi in situ XPS, respectively. The catalyst with weak NPSI achieved higher CO2 yields and selectivities at temperatures below 225 °C compared to the sample with strong NPSI. However, relatively high degrees of reduction of Co3O4 to metallic Co were reached between 250 and 350 °C for the same catalyst. The presence of metallic Co led to the undesired formation of CH4, reaching a yield of over 90% above 300 °C. The catalyst with strong NPSI formed very low amounts of metallic Co (less than 1%) and CH4 (yield of up to 20%) even at 350 °C. When the temperature was decreased from 350 to 50 °C under the reaction gas, both catalysts were slightly reoxidized and gradually regained their CO oxidation activity, while the formation of CH4 diminished. The present study shows a strong relationship between catalyst performance (i.e., activity and selectivity) and phase stability, both of which are affected by the strength of the NPSI. When using a metal oxide as the active CO-PrOx catalyst, it is important for it to have significant reduction resistance to avoid the formation of undesired products, e.g., CH4. However, the metal oxide should also be reducible (especially on the surface) to allow for a complete conversion of CO to CO2 via the Mars-van Krevelen mechanism.

Unraveling the H2 Promotional Effect on Palladium-Catalyzed CO Oxidation Using a Combination of Temporally and Spatially Resolved Investigations.

The promotional effect of H2 on the oxidation of CO is of topical interest, and there is debate over whether this promotion is due to either thermal or chemical effects. As yet there is no definitive consensus in the literature. Combining spatially resolved mass spectrometry and X-ray absorption spectroscopy (XAS), we observe a specific environment of the active catalyst during CO oxidation, having the same specific local coordination of the Pd in both the absence and presence of H2. In combination with Temporal Analysis of Products (TAP), performed under isothermal conditions, a mechanistic insight into the promotional effect of H2 was found, providing clear evidence of nonthermal effects in the hydrogen-promoted oxidation of carbon monoxide. We have identified that H2 promotes the Langmuir-Hinshelwood mechanism, and we propose this is linked to the increased interaction of O with the Pd surface in the presence of H2. This combination of spatially resolved MS and XAS and TAP studies has provided previously unobserved insights into the nature of this promotional effect.

Structural behaviour of copper chloride catalysts during the chlorination of CO to phosgene.

The interaction of CO with an attapulgite-supported Cu(ii)Cl2 catalyst has been examined in a micro-reactor arrangement. CO exposure to the dried, as-received catalyst at elevated temperatures leads to the formation of CO2 as the only identifiable product. However, phosgene production can be induced by using a catalyst pre-treatment where the supported Cu(ii)Cl2 sample is exposed to a diluted stream of chlorine. Subsequent CO exposure at ∼370 °C then leads to phosgene production. In order to investigate the origins of this atypical set of reaction characteristics, a series of X-ray absorption experiments were performed that were supplemented by DFT calculations. XANES measurements establish that at the elevated temperatures connected with phosgene formation, the catalyst is comprised of Cu+ and a small amount of Cu2+. Moreover, the data show that unique to the chlorine pre-treated sample, CO exposure at elevated temperature results in a short-lived oxidation of the copper. On the basis of calculated CO adsorption energies, DFT calculations indicate that a mixed Cu+/Cu2+ catalyst is required to support CO chemisorption.

Operando spectroscopy study of the carbon dioxide electro-reduction by iron species on nitrogen-doped carbon.

The carbon-carbon coupling via electrochemical reduction of carbon dioxide represents the biggest challenge for using this route as platform for chemicals synthesis. Here we show that nanostructured iron (III) oxyhydroxide on nitrogen-doped carbon enables high Faraday efficiency (97.4%) and selectivity to acetic acid (61%) at very-low potential (-0.5 V vs silver/silver chloride). Using a combination of electron microscopy, operando X-ray spectroscopy techniques and density functional theory simulations, we correlate the activity to acetic acid at this potential to the formation of nitrogen-coordinated iron (II) sites as single atoms or polyatomic species at the interface between iron oxyhydroxide and the nitrogen-doped carbon. The evolution of hydrogen is correlated to the formation of metallic iron and observed as dominant reaction path over iron oxyhydroxide on oxygen-doped carbon in the overall range of negative potential investigated, whereas over iron oxyhydroxide on nitrogen-doped carbon it becomes important only at more negative potentials.

Operando Spectroscopic Studies of Cu-SSZ-13 for NH3-SCR deNOx Investigates the Role of NH3 in Observed Cu(II) Reduction at High NO Conversions.

The small pore zeolite chabazite (SSZ-13) in the copper exchanged form is a very efficient material for the selective catalytic reduction by ammonia (NH3) of nitrogen oxides (NOx) from the exhaust of lean burn engines, typically diesel powered vehicles. The full mechanism occurring during the NH3-SCR process is currently debated with outstanding questions including the nature and role of the catalytically active sites. Time-resolved operando spectroscopic techniques have been used to provide new level of insights in to the mechanism of NH3-SCR, to show that the origin of stable Cu(I) species under SCR conditions is potentially caused by an interaction between NH3 and the Cu cations located in eight ring sites of the bulk of the zeolite and is independent of the NH3-SCR of NOx occurring at Cu six ring sites within the zeolite.