Evaluation of water quality index and geochemical characteristics of surfacewater from Tawang India.

In this study,the water samples were collected from 31 sites of Tawang, Arunachal Pradesh, India (North-Eastern Himalaya), during the winter season to check the suitability of water for drinking and irrigation purposes.The study scientifically demonstrates the estimation of Water quality index (WQI) andhydrogeochemical characteristics of surface water samples by utilizing multivariate statistical methods. The main water quality parameters considered for this study were TDS, conductivity, salinity, pH, hardness, cations and anions. WQI was calculated in order to find out the deviation in the water quality parameters particularly with respect to BIS permissible limits.The major influencing factors responsible for the variation in these parameters were derived by using Principal component analysis (PCA) and Correlation matrix.To check the suitability of water for drinking purpose, hydrogeochemical facies and rock water interaction was derived by using well established methods such as Piper Plot (determine water type), WQI (Quality monitoring), and saturation index (for mineral dissolution). The results revealed that the silicate weathering was the main ionic source in comparison to carbonate weathering which is due to the higher dissolution capacity of silicate minerals.The results of the scattered plot between (Ca2+ + Mg2+)-(HCO3- + SO42-) versus (Na+ + K+)-Cl- (meq/L) highlighted thation exchange occurs between Mg2+ and Ca2+ofsurface water with Na+ and K+of rock /soil. This means that calcium ion was getting adsorbed, and sodium ion was getting released. The Ca2+-Mg2+-HCO3-, Na+-HCO3-and Na+-Cl- type of surface water suggested permanent and temporary hardness respectively in the studied region. The dominant cations of this study were Na+ and Ca2+ while the dominant anions were HCO3- and SO42-. In order to check the suitability of water sources for irrigation, parameters like, Magnesium hazard (MH), Total hardness (TH), Permeability Index (PI), Kelly Index (KI), Sodium adsorption rate (SAR), Sodium percentage (Na%), and Residual sodium carbonate (RSC) were determined. The results showed that 93% of the samples had PI score < 75, which indicates the suitability of the water for irrigation. Also the WQI calculation showed an average WQI value of 82.49, amongst which 61% samples were in the range of 0-50 being considered as good for drinking, while 39% were catageorised as unsuitable for drinking showing a value of > 50. Hence the above findings reveal that geogenic activities play a major role in influencing the water quality of Tawang region. Hence suitable water treatment technologies or methods might be used to eliminate thenon desirable elements and minerals present in surface water.

Anteromedial Surface Plating for Midshaft Fracture Humerus Through an Anterolateral Approach - A Better Option than Anterolateral Plating.

INTRODUCTION: Osteosynthesis by plate fixation of humeral shaft fractures as a gold standard for fracture fixation has been proven beyond doubt. However, during conventional anterolateral plating Radial nerve injury may occur which can be avoided by applying plate on the medial flat surface. The aim of this study was to evaluate the results of application of plate on the flat medial surface of humerus rather than the conventional anterolateral surface. MATERIALS AND METHODS: This study was conducted between Oct 2010 to Dec 2015. One-hundred-fifty fracture shafts of the humerus were treated with the anteromedial plating through the anterolateral approach. RESULTS: One-hundred-fifty patients with a fracture shaft of the humerus were treated with anteromedial plating. Twenty were female (mean ±SD,28 years±4.5) and 130 were male (mean ± SD, 38 years±5.6). One hundred and forty-eight out of 150 (98.6%) patients achieved union at 12 months. Two of three patients developed a superficial infection, both of which were treated successfully by antibiotics and one developed a deep infection, which was treated by wound debridement, prolonged antibiotics with the removal of the plate and subsequently by delayed plating and bone grafting. CONCLUSION: In the present study, we applied plate on the anteromedial flat surface of humerus using the anterolateral approach. It is an easier and quicker fixation as compared to anterolateral plating because later involved much more dissection than a medial application of the plate and this application of plate on a medial flat surface, does not required Radial nerve exposure and palsy post-operatively. The significant improvement in elbow flexion without brachialis dissection is also a potential benefit of this approach. Based on our results, we recommend the application of an anteromedial plate for treatment of midshaft fractures humerus.

Anteromedial Surface Plating for Midshaft Fracture Humerus Through an Anterolateral Approach - A Better Option than Anterolateral Plating

@#Introduction: Osteosynthesis by plate fixation of humeral shaft fractures as a gold standard for fracture fixation has been proven beyond doubt. However, during conventional anterolateral plating Radial nerve injury may occur which can be avoided by applying plate on the medial flat surface. The aim of this study was to evaluate the results of application of plate on the flat medial surface of humerus rather than the conventional anterolateral surface. Materials and Methods: This study was conducted between Oct 2010 to Dec 2015. One-hundred-fifty fracture shafts of the humerus were treated with the anteromedial plating through the anterolateral approach. Results: One-hundred-fifty patients with a fracture shaft of the humerus were treated with anteromedial plating. Twenty were female (mean ±SD,28 years±4.5) and 130 were male (mean ± SD, 38 years±5.6). One hundred and forty-eight out of 150 (98.6%) patients achieved union at 12 months. Two of three patients developed a superficial infection, both of which were treated successfully by antibiotics and one developed a deep infection, which was treated by wound debridement, prolonged antibiotics with the removal of the plate and subsequently by delayed plating and bone grafting. Conclusion: In the present study, we applied plate on the anteromedial flat surface of humerus using the anterolateral approach. It is an easier and quicker fixation as compared to anterolateral plating because later involved much more dissection than a medial application of the plate and this application of plate on a medial flat surface, does not required Radial nerve exposure and palsy post-operatively. The significant improvement in elbow flexion without brachialis dissection is also a potential benefit of this approach. Based on our results, we recommend the application of an anteromedial plate for treatment of midshaft fractures humerus.

MR Geyser Sign in chronic rotator cuff tears.

Acromio-clavicular (AC) joint cysts are rare presentation of chronic shoulder pathology. These cysts may be observed secondary to either degenerative changes in the AC joint with an intact rotator cuff (type 1 cyst) or following a chronic rotator cuff tear (type 2 cyst). The latter phenomenon is known as Geyser Sign and is described by ultrasound, conventional arthrogram and magnetic resonance imaging (MRI). We present a case of chronic rotator cuff tear presenting with a large type 2 cyst and Geyser Sign on MRI.

The Importance of Flexion MRI in Hirayama Disease with Special Reference to Laminodural Space Measurements.

BACKGROUND AND PURPOSE: Hirayama disease is a benign focal amyotrophy of the distal upper limbs involving C7, C8, and T1 segmental myotomes with sparing of the brachioradialis and proximal muscles of the upper limb innervated by C5-6 myotomes. The objective of the present study was to study the utility of MR imaging in young patients presenting with weakness and wasting of the distal upper extremity and to evaluate the importance of the laminodural space during flexion cervical MR imaging. MATERIALS AND METHODS: This was a prospective cross-sectional study conducted from January 2014 to July 2017 in a tertiary care center from Northeast India. Forty-five patients with clinically definite Hirayama disease underwent electrophysiologic evaluation followed by MR imaging of the cervical spine. RESULTS: The mean age at recruitment was 22.8 ± 5.5 years. Forty patients (88.9%) had unilateral and 5 (11.1%) had bilateral upper extremity involvement. Cervical cord T2-weighted hyperintensities were demonstrated in 16 patients (35.6%), of which 15 (33.3%) had anterior horn cell hyperintensities. Flexion MR imaging showed loss of the posterior dural attachment, forward shifting of the posterior dural sac with postcontrast enhancement, and prominent posterior epidural venous plexus in all patients. The laminodural space at maximum forward shifting of the posterior dural sac ranged from 3 to 9.8 mm, with a mean distance of 5.99 mm (95% confidence interval, 5.42-6.57 mm). CONCLUSIONS: Flexion cervical MR imaging is a very useful investigation in diagnosing Hirayama disease. The increase in the laminodural space and the presence of cervical cord flattening during flexion are essential for diagnosis.

Development of an effective and efficient DNA isolation method for Cinnamomum species.

Different species of Cinnamomum are rich in polysaccharide's and secondary metabolites, which hinder the process of DNA extraction. High quality DNA is the pre-requisite for any molecular biology study. In this paper we report a modified method for high quality and quantity of DNA extraction from both lyophilized and non-lyophilized leaf samples. Protocol reported differs from the CTAB procedure by addition of higher concentration of salt and activated charcoal to remove the polysaccharides and polyphenols. Wide utility of the modified protocol was proved by DNA extraction from different woody species and 4 Cinnamomum species. Therefore, this protocol has also been validated in different species of plants containing high levels of polyphenols and polysaccharides. The extracted DNA showed perfect amplification when subjected to RAPD, restriction digestion and amplification with DNA barcoding primers. The DNA extraction protocol is reproducible and can be applied for any plant molecular biology study.

Antibacterial and hemolysis activity of polypyrrole nanotubes decorated with silver nanoparticles by an in-situ reduction process.

Polypyrrole nanotube-silver nanoparticle nanocomposites (PPy-NTs:Ag-NPs) have been synthesized by in-situ reduction of silver nitrate (AgNO3) to suppress the agglomeration of Ag-NPs. The morphology and chemical structure of the nanocomposites have been studied by HRTEM, SEM, XRD, FTIR and UV-vis spectroscopy. The average diameter of the polypyrrole nanotubes (PPy-NTs) is measured to be 130.59±5.5 nm with their length in the micrometer range, while the silver nanoparticles (Ag-NPs) exhibit spherical shape with an average diameter of 23.12±3.23 nm. In-vitro blood compatibility of the nanocomposites has been carried out via hemolysis assay. Antimicrobial activity of the nanocomposites has been investigated with Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) bacteria. The results depict that the hemolysis and antimicrobial activities of the nanocomposites increase with increasing Ag-NP concentration that can be controlled by the AgNO3 precursor concentration in the in-situ process.

Fe2O3/C nanocomposites having distinctive antioxidant activity and hemolysis prevention efficiency.

Tailored magnetic iron oxide nanoparticles hold the prospect for nouveau applications in the field of biomedical technology. Herein, we report novel functionalities of this iron oxide system by developing a hybrid of Fe2O3/C to make it a multifunctional biomedical agent. A detailed magnetic study carried out at varying temperatures confirms the intrinsic superparamagnetic character of these iron oxide-carbon composites. The potential of the nanocomposite for biomedical applications has been evaluated by its ability to scavenge free radical by 1,1-diphenyl-2-picrylhydrazyl radical (DPPH) assay. Moreover, the nanocomposite was monitored for successful hemolysis inhibition of mammalian erythrocytes. The nanocomposite showed promising compatibility with the peripheral blood mononuclear cells (PBMC) which was visualized from trypan blue dye exclusion assay. Biocompatible carbon coating over the iron oxide nanoparticles with these functionalities has transformed it to a multifunctional nanoparticulate biomedical agent potential for future clinical translation.

Brevibacillus laterosporus strain BPM3, a potential biocontrol agent isolated from a natural hot water spring of Assam, India.

A bacterial strain designated as BPM3 isolated from mud of a natural hot water spring of Nambar Wild Life Sanctuary, Assam, India, strongly inhibited growth of phytopathogenic fungi (Fusarium oxysporum f. sp. ciceri, F. semitectum, Magnaporthe grisea and Rhizoctonia oryzae) and gram-positive bacterium (Staphylococcus aureus). The maximum growth and antagonistic activity was recorded at 30°C, pH 8.5 when starch and peptone were amended as carbon and nitrogen sources, respectively. In greenhouse experiment, this bacterium (BPM3) suppressed blast disease of rice by 30-67% and protected the weight loss by 35-56.5%. The maximum disease protection (67%) and weight loss protection (56.5%) were recorded when the bacterium was applied before 2 days of the pathogen inoculation. Antifungal and antibacterial compounds were isolated from the bacterium which also inhibited the growth of these targeted pathogens. The compounds were purified and on spectroscopic analysis of a purified fraction having R(f) 0.22 which showed strong antifungal and antibacterial activity indicated the presence of C-H, carbonyl group, dimethyl group, -CH(2) and methyl group. The bacterium was characterized by morphological, biochemical and molecular approaches and confirmed that the strain BPM3 is Brevibacillus laterosporus.

Optimization of medium and cultivation conditions for L-amino acid oxidase production by Aspergillus fumigatus.

A fungal strain was selected from the microbial repository of the North-East Institute of Science and Technology, Jorhat, India, which could produce a high yield of L-amino acid oxidase. 18SrRNA, ITS1, 5.8SrRNA ITS2, and partial 28 S rRNA sequencing and phenotypic characteristics indicate that it belong to the species Aspergillus fumigatus (designated as P13). Maximum production of enzyme (59.55 x 10-3 U/mg dry cell mass) was obtained in a medium containing 10 g/L glucose, 4 g/L yeast extract, and 4 g/L ammonium sulfate, with 20 mmol/L of L-threonine as the inducer. The optimum temperature for enzyme production was 30 degrees C at pH 7.0, with a shaking speed of 200 r/min. At 96 h, the enzyme activity was maximum. The A. fumigatus P13 L-amino acid oxidase accepts a broad substrate range, and the maximum enzyme activity (20.41 x 10-3 U/mg dry cell mass) was obtained with 50 mmol/L of L-tyrosine. In the literature, no reports have been found regarding the production of L-amino acid oxidase by A. fumigatus. The enzyme showed enantiomerically pure amino acid formation, which has tremendous demand in industrial applications.

Agar immobilized yeast cells in tubular reactor for ethanol production.

Saccharomyces cerevisiae cells were immobilized in agar gel and used in a tubular reactor for conversion of cane molasses to ethanol at 30 degrees C, pH 4.5. Reactor was used in a continuous operation to test the operational stability and ethanol productivity. After 100 days of continuous fermentation at a dilution rate of 0.67 hr-1, some deactivation of cells was observed, but ethanol productivity was recovered by reactivating the cells by sparging air intermittently. It was found that intermittent reactivation during continuous operation was very important for satisfactory performance of the reactor. During operation, gel beads maintained their rigidity. Maximum ethanol concentration (94.9 g/L) was obtained with a feed containing 255 g/L reducing sugar, at a dilution rate of 0.2 hr-1. Maximum volumetric productivity (79.5 g ethanol /L/hr), specific ethanol productivity (0.58 g ethanol/g cells/hr), specific sugar uptake rate (1.12 g sugar/g cells/hr) and ethanol yield coefficient (0.43 g ethanol/g sugar) were obtained with a feed containing 195 g/L reducing sugar at a dilution rate of 1.33 hr-1.

Filariasis in the labour population of a tea estate in Upper Assam.

Preliminary random and mass blood surveys undertaken between 2000-0100 h in a tea garden of Upper Assam revealed more than 8 per cent positivity for microfilaria (mf) of Wuchereria bancrofti. The mf carriers were considerably high among males (73) as compared to females (48). Culex quinquefasciatus was incriminated as a vector with man hour density of 68.5 in human dwellings (indoors). The detection of mf in children who had never moved from the area and filaria larvae in vector mosquitoes collected from human dwellings indicate that indigenous transmission is going on in the garden and that filariasis has become a local health problem.

Effect of growth temperature and media composition on the fatty acid composition of Bacillus stearothermophilus AN 002.

The influence of growth temperature, media composition and cell age on the chemical composition of Bacillus stearothermophilus strain AN 002 has been determined. The total cellular protein decreased and the free amino acid content increased with growth temperature, in both exponential and stationary growth phase. The protein and free amino acid contents of cells were higher in the stationary phase than in the exponential phase, irrespective of growth temperature and media composition. The RNA content was only reduced in cells grown at 55 degrees C. No significant variations were observed in the DNA and carbohydrate contents with respect to growth temperature and cell age. The total lipid and fatty acid compositions on the other hand varied as a function of growth temperature, cell age and media composition. Differences in the relative concentrations of even, odd and branched chain fatty acids were noticed. No variation was observed in the antiiso and unsaturated fatty acids with respect to growth temperature. The unique variations in the fatty acid composition and total lipids at the growth temperature of 50 degrees C and their variations in the stationary growth phase seem to be characteristic for B. stearothermophilus AN 002.

DNA haplotypes and frameworks associated with the beta-globin gene in the Kachari population of Assam (India).

DNA haplotypes and frameworks associated with the beta-globin gene were determined in a Tibeto-Burman group, the Kachari, from Upper Assam, India, using restriction analysis at eight restriction sites. Of the total of 59 subjects, 26 were homozygous for HBB*A and 33 homozygous for HBB*E. Complete haplotype determination in 33 subjects revealed a conspicuous difference in haplotype distribution between HBB*A- and HBB*E-bearing chromosomes. The Southeast Asian HBB*E-associated haplotype -+- +- (27-2 in the present terminology) predominated on HBB*E chromosomes. The previously established beta-globin-associated frameworks 1, 2 and 3 were evenly distributed among the HBB*A chromosomes, whereas all HBB*E chromosomes had framework 2. These findings favor a common origin of the HBB*E gene in Southeast Asia and Assam.

Interference with sporulation can stimulate the rate of a proteinase synthesis in Bacillus megaterium.

Bacillus megaterium, in which sporulation was blocked either by mutation or with netropsin, synthesizes during the stationary phase more exocellular proteinase than the sporulating culture. The asporogenic mutant synthesizes the enzyme at a higher rate and for a longer time than does the sporulating population. The culture, whose sporulation was inhibited by netropsin, produces the proteinase at a higher rate, although for only a limited time interval.