Porous NiTi Dental Implant Fabricated by a Metal Injection Molding: An in Vivo Biocompatibility Evaluation in an Animal Model.

This study assessed the corrosion resistance, intracutaneous reactivity, acute systemic toxicity, and in situ tissue effect of the implantation of porous NiTi fabricated by metal injection molding in animal models. For the intracutaneous reactivity study, five intracutaneous injections were administered per site with and without the tested extract in polar and nonpolar solutions. The extract was also delivered via intravenous and intraperitoneal routes for acute systemic toxicity. TiAl6 V4 (control) and porous NiTi were implanted in rabbit femora for a period of 13 weeks to evaluate the in situ tissue response. Corrosion was evaluated through open and cyclic polarization in PBS, while biocompatibility was investigated by assessing the general conditions, skin irritation score (edema and erythema), and histopathology. No active dissolution or hysteresis loop was observed in the corrosion study. None of the animals exhibited death, moribundity, impending death, severe pain, self-mutilation, or overgrooming. No edema was observed at injection sites. Only the positive control showed an erythematous reaction at 24, 48, and 72 h observations (p < 0.001). Porous NiTi showed a low in situ biological response for inflammation, neovascularization, and fibrosis in comparison to the control implant (p = 0.247, 0.005, and 0.011, respectively). Porous NiTi also demonstrated high pitting corrosion resistance while causing no acute hypersensitivity or acute systemic toxicity. The study concludes that porous NiTi implants were unlikely to cause local sensitization, acute systemic toxicity, or chronic inflammatory reactions in an animal model. Porous NiTi also exhibited osseointegration equivalent to Ti6AI4 V of known biocompatibility.

Effects of Surface Treatment and Thermocycling on the Shear Bond Strength of Zirconia-Reinforced Lithium Silicate Ceramic.

PURPOSE: To investigate the effects of different surface treatments and thermocycling on shear bond strength (SBS) be-tween resin cement and zirconia-reinforced lithium-silicate (ZLS) ceramic. MATERIALS AND METHODS: 96 ZLS ceramic specimens were randomly allocated to four different surface treatment groups: etch and silane (ES), etch and universal primer (EUP), self-etching primer (SEP), and sandblasting and silane (SS). Stan-dardized composite cylinders were bonded to surface-treated ZLS ceramic, after which SBS was obtained either after 24-h water storage only or with an additional 5000 thermal cycles (TC), resulting in eight subgroups (n = 12). After evaluation of failure mode under a stereomicroscope, representative SEM images were acquired. To examine areal average surface roughness (Sa), additional ZLS specimens were prepared and randomly allocated to 3 groups: hydrofluoric acid etching, self-etching primer, and sandblasting (n = 10). Supplementary specimens were examined using field-emission scanning electron microscopy (FE-SEM) (n = 2) and atomic force microscopy (AFM) (n = 2) to investigate their surface topographies. RESULTS: ANOVA showed a statistically significant difference in SBS following different surface treatment protocols after 24-h water storage (p < 0.001). However, TC groups revealed no statistically significant difference in their SBS (p = 0.394). All surface treated groups were significantly affected by TC (p < 0.001), except for the SS group (p = 0.48). Sa was signifi-cantly influenced by the different surface treatment protocols (p < 0.001). CONCLUSION: The ability of self-etching primer to achieve comparable bond strength with a less technique-sensitive ap-proach makes it a favorable alternative to ES for the surface treatment of ZLS ceramics.

Acrylic tooth splint-An immediate provisionalisation following tooth extraction; a series of case reports.

Key Clinical Message: Numerous techniques for provisionally replacing a single tooth at the aesthetic zone while planning for future dental implant placement, while soft and hard tissues heal, are critical in restorative treatment strategy. The available materials, simplicity, cost, and impact on the potential implant location should be considered when evaluating the treatment choices. Abstract: Replacement of a single anterior tooth in the aesthetic zone while planning for future implant placement is crucial to the restorative treatment plan. Several methods exist for immediate provisionalisation of the extracted tooth while waiting for soft and hard tissue healing. Although there's a myriad of possible provisionalisation methods available, each option has its advantages and disadvantages. The treatment options should weigh various factors such as the available materials, ease of fabrication, costs, and the effect on the future implant site. This article describes three clinical cases demonstrating a simple yet cost-effective technique to temporarily replace an extracted single anterior tooth, enhancing patient satisfaction and increasing compliance before receiving the definitive implant restoration. The pro and cons for each treatment option available as opposed to the technique involved in the three cases used are also described.

Validation of the Malay Oral Impacts on Daily Performances and Evaluation of Oral Health-Related Quality of Life in a Multi-Ethnic Urban Malaysian Population: A Cross-Sectional Study.

Oral Impacts on Daily Performances (OIDP) can be used as a generic or condition-specific oral health-related quality of life (OHRQoL) instrument. It offers different contexts on how dental conditions affect OHRQoL. This cross-sectional study aimed to validate a newly translated Malay OIDP (OIDP-M), compare OHRQoL, decayed, missing, or filled teeth (DMFT) in Malaysians, and investigate factors associated with OHRQoL. A total of 368 Malaysians were surveyed and examined for DMFT. Short-form oral health impact profile-Malaysia [S-OHIP(M)] and OIDP-M were used to measure OHRQoL. The OIDP-M was tested for reliability and validity. DMFT, S-OHIP(M), and OIDP-M between ethnicities were compared. Associations between ethnicity, DMFT, S-OHIP(M), and OIDP-M of Malays and Chinese were evaluated through partial correlation. Malays and Chinese had more filled teeth and DMFT compared with Indians. Malays reported worse OHRQoL through S-OHIP(M). Decayed teeth were positively associated with S-OHIP(M), physical, psychological, social disabilities, and handicap. For OIDP-M, decayed teeth were positively associated with OIDP-M, working, and sleeping. Missing teeth and ethnicity were positively associated with eating and speaking. Filled teeth were negatively associated with cleaning teeth. The OIDP-M was reliable and valid for evaluating OHRQoL. There were differences in DMFT and OHRQoL between ethnicities. Ethnicity affects OHRQoL, where Malays experienced worse OHRQoL due to dental problems.

Effect of training on time efficiency and marginal adaptation of computer-aided design/computer-aided manufacturing crowns among dental students.

INTRODUCTION: The computer-aided design/computer-aided manufacturing (CAD/CAM) technology has revolutionised dentistry at present. An operator's skills can affect the overall clinical duration and marginal accuracy of the prosthesis fabricated through this workflow. The aim of this study was to assess the effect of CAD/CAM hands-on training compared with that of a self-instructional video on the performance of dental students in digital impression and fabrication of a CAD/CAM crown. METHODS: In this cross-sectional study, 30 undergraduate dental students were shown a CEREC demonstration video. Each operator then captured a digital impression using the intra-oral scanner, and a crown was subsequently milled. All participants underwent a training course before repeating the process. Marginal discrepancy for each crown on its abutment tooth was measured before and after training using a stereomicroscope and was evaluated using Wilcoxon signed rank test. The duration taken for the process was recorded before and after training and evaluated using paired t-test. RESULTS: The overall mean ±standard deviation marginal adaptation for the CEREC crowns was 78.15 ± 42.83 µm before training and 52.41 ± 17.12 µm after training. The Wilcoxon signed rank test found significant difference (p < .05) in terms of marginal adaptation of crowns fabricated before and after training. Paired t-tests showed that the time efficiency after training significantly improved compared with that before training. CONCLUSIONS: Training with guided feedback is crucial to improve the time efficiency of making a digital impression and marginal adaptation of fixed prosthesis using the CAD/CAM technology.

Effect of cement space on marginal discrepancy and retention of CAD/CAM crown.

This research aimed to evaluate the effect of cement space on the marginal discrepancy and retention of computer-aided design/computer-aided manufacturing (CAD/CAM) crowns. A total of 30 premolar Frasaco teeth were machined to receive crowns with cement spaces of 70, 90, and 110 µm. The marginal discrepancy measurements were done before and after cementation. Pull-off test was conducted using universal testing machine (UTM). Data was analyzed using two-way mixed ANOVA with post-hoc Bonferroni test and Kruskal-Wallis test. The crowns with cement space of 70 µm showed a significantly higher absolute marginal discrepancy than those with 90 and 110 µm. No significant effect on the crown retention was found. Within the limitations of this study, modifying cement space to 90 µm and 110 µm may improve the marginal adaptation of CAD/CAM crown, whereas adjusting cement space from 70 to 110 µm did not significantly affect the crown retention.

Fabricating CAD/CAM Implant-Retained Mandibular Bar Overdentures: A Clinical and Technical Overview.

This report describes the clinical and technical aspects in the oral rehabilitation of an edentulous patient with knife-edge ridge at the mandibular anterior edentulous region, using implant-retained overdentures. The application of computer-aided design and computer-aided manufacturing (CAD/CAM) in the fabrication of the overdenture framework simplifies the laboratory process of the implant prostheses. The Nobel Procera CAD/CAM System was utilised to produce a lightweight titanium overdenture bar with locator attachments. It is proposed that the digital workflow of CAD/CAM milled implant overdenture bar allows us to avoid numerous technical steps and possibility of casting errors involved in the conventional casting of such bars.