Determination of polyethylene glycol in low-density polyethylene by large volume injection temperature gradient packed capillary liquid chromatography.

Polyethylene glycol (PEG) 20000 in low-density polyethylene has been determined using column switching and inverse temperature programming in reversed-phase packed capillary liquid chromatography with evaporative light scattering detection. PEG 20000 was extracted into water from the polyethylene dissolved in toluene and PEG 35000 was added as an internal standard (I.S.). The samples in aliquots of 100 microl were reconcentrated on the enrichment column using a loading mobile phase of acetonitrile-water (3:97, v/v) at a flow-rate of 75 microl/min for 3 min, then back-flushed and separated on the analytical column with acetonitrile-THF-water (40:5:55, v/v) as mobile phase. The column temperature was reduced from 68 to 55 degrees C with a ramp of -1.5 degrees C/min, held constant for 3 min and then reduced further to 45 degrees C with a -1.5 degrees C/min ramp and kept constant for 1 min. The analysis runtime was 20 min. The recovery of PEG 20 000 was determined to 65.1% with 2.8% RSD and the mass limit of detection of PEG 20 000 was 1.25 microg. The within-assay and between day precision of the retention times of both PEG 20000 and PEG 35000 displayed RSD of less than 1.1% (n = 9), while the overall area ratio RSD of 100 microg/ml PEG 20000 over PEG 35000 was 1.3% (n = 9). The method was linear within the investigated concentration range 25-125 microg/ml (R2 = 0.9983). In addition, a mixture of PEG 4000, 8000, 10000, 20000 and 35000 was analysed on the system to demonstrate the possibility of analysing several PEGs in a sample with the use of temperature gradient elution.

Determination of rotenone in river water utilizing packed capillary column switching liquid chromatography with UV and time-of-flight mass spectrometric detection.

Fast and sensitive packed capillary column switching liquid chromatography methodology has been developed for the determination of the pesticide rotenone in river water. Sample volumes of up to 1 ml are loaded onto a 23 x 0.25 mm, 5 microm Kromasil C18 packed capillary precolumn using a noneluting solvent composition of water-acetonitrile (99:1, v/v) at flow-rates up to 100 microl/min prior to solute backflushing onto a 200 x 0.32 mm, 3.5 microm Kromasil C18 packed capillary analytical column using a mobile phase of water-acetonitrile (30:70, v/v) at a flow-rate of 5 microl/min. The method was evaluated using river water samples spiked with rotenone in the concentration range 0.5-50 ng/ml using UV detection. The within-assay precision was between 5.0 and 7.7% relative standard deviation (RSD, n = 6) and the between assay precision was between 7.5 and 8.9% RSD (n = 6). The method was linear within the investigated mass range displaying a calibration curve correlation factor of 0.997. The mass limit of detection was 10 pg corresponding to a concentration limit of detection of 10 pg/ml, using time-of-flight mass spectrometry.

Simultaneous determination of citalopram, fluoxetine, paroxetine and their metabolites in plasma by temperature-programmed packed capillary liquid chromatography with on-column focusing of large injection volumes.

A miniaturized temperature-programmed packed capillary liquid chromatographic method with on-column large volume injection and UV detection for the simultaneous determination of the three selective serotonin reuptake inhibitors citalopram, fluoxetine, paroxetine and their metabolites in plasma is presented. An established reversed-phase C8 solid-phase extraction method was employed, and the separation was carried out on a 3.5-microm Kromasil C18 0.32x300 mm column with temperature-programming from 35 (3 min) to 100 degrees C (10 min) at 1.3 degrees C/min. The mobile phase consisted of acetonitrile-45 mM ammonium formate (pH 4.00) (25:75, v/v). The non-eluting sample focusing solvent composition acetonitrile-45 mM ammonium formate (pH 4.00) (3:97, v/v) allowed injection of 10 microl or more of the plasma extracts. The method was validated for the concentration range 0.05-5.0 microM, and the calibration curves were linear with coefficients of correlation >0.993. The limits of quantification for the antidepressants and their metabolites ranged from 0.05 to 0.26 microM. The within and between assay precision of relative peak height were in the range 2-22 and 2-15% relative standard deviation, respectively. The within and between assay recoveries were in the 61-99 and 54-92% range for the antidepressants, respectively, and between 52-102 and 51-102% for the metabolites.

Separation of polyethylene glycol oligomers using inverse temperature programming in packed capillary liquid chromatography.

Inverse temperature programming in packed capillary liquid chromatography coupled to evaporative light-scattering detection has been used to resolve native polyethylene glycol (PEG) oligomers. The model compound, PEG 1000, was separated on a 300 mm x 0.32 mm I.D. capillary column packed with 3 microm Hypersil ODS particles with acetonitrile-water (30:70, v/v) as mobile phase. The retention of the PEG oligomers increased with increasing temperature, different from what is commonly observed in liquid chromatography. The retention times of the oligomers were approximately doubled for each 25 degrees C increment of the column temperature in the temperature range 30-80 degrees C. The oligomers were almost unretained and co-eluted at a column temperature of 30 degrees C. At 80 degrees C a baseline separation of more than 22 peaks was obtained, but the last eluting peaks were severely broadened and all oligomers did not elute. When a negatively sloped temperature ramp from 80 to 25 degrees C at -1.5 degrees C/min was applied, the peak shapes were improved, additional peaks were detected and the analysis time was reduced by 48%. In the temperature programming mode, the intra-day precision of the retention times ranged from 0.5 to 5.8% (n=5).

Determination of 1-(2-methoxyphenyl)piperazine derivatives of isocyanates at low concentrations by temperature-programmed miniaturized liquid chromatography.

A temperature-programmed packed capillary LC method with large-volume injection on-column focusing has been developed for screening and determination of 1-(2-methoxyphenyl)piperazine derivatives of airborne toluene-2,4-diisocyanate, toluene-2,6-diisocyanate, hexamethylenediisocyanate and methylenebisphenyl-4,4-diisocyanate, based on sampling methods described in MDHS 25/3. Injection volumes up to 100 microl were successfully loaded onto the 250x0.32 mm I.D. capillary column packed with 3 microm Hypersil ODS particles. The isocyanate derivatives were loaded at 10 degrees C and eluted by a three-step temperature program starting at 10 degrees C for 10 min, followed by a temperature ramp of 2.5 degrees C min(-1) to 45 degrees C and then 9.9 degrees C min(-1) to 90 degrees C. The mobile phase consisted of acetonitrile-acetate buffer (3% triethylamine, pH 4.5) (45:55, v/v). The isocyanate derivatives were dissolved in acetonitrile-acetate buffer (3% triethylamine, pH 4.5) (30:70, v/v) to achieve sufficient focusing. The concentration limit of detection of the individual derivatives utilizing an "U" shaped flow cell with a 8.0 mm light path and an injection volume of 100 microl was 44, 87, 43 and 210 pg ml(-1) for toluene-2,6-diisocyanate, hexamethylenediisocyanate, toluene-2,4-diisocyanate and methylenebisphenyl-4,4-diisocyanate, respectively. Within the investigated concentration range, 10-500 ng ml(-1), the linear calibration curves gave correlation coefficients ranging from 0.994 to 0.998. The repeatability of the method with regard to retention time and peak height ranged from 0.3 to 1.1% and 1.1 to 2.3% (n=9) relative standard deviation, respectively. The average recovery of the method, with regard to toluene-2,4-diisocyanate, was 97.7+/-1.6% (n=9).

Nonaqueous electrochromatography on continuous bed columns of sol-gel bonded large-pore C18 material: separation of retinyl esters.

A nonaqueous electrochromatographic reversed-phase separation method for retinyl esters using continuous bed columns has been developed. The packing material 7 microm Nucleosil 4,000 angstroms C18 was sol-gel bonded in 180 microm I.D. capillaries. The mobile phase used was 2.5 mM lithium acetate in N,N-dimethylformamide-acetonitrile-methanol (2+7+1, v/v). At 350 V/cm and 30 degrees C, this mobile phase composition gave rise to an electroosmotic flow of 1 mm/s. No Joule heating nor bubble formation were observed even at 625 V/cm (17 microA). With a 36 cm L(eff) column complete separation of the commercially available and synthesized standards (all-trans-retinyl acetate, palmitate, heptadecanoate, stearate, oleoate, and linoleoate) was obtained within 10 min. The within-day and between-day variations of retention times of all-trans-retinyl palmitate were <0.3% relative standard deviation (RSD) (n=3) and <2% RSD (n=6), respectively. The within-day and between-day variations of peak areas were both <2% (both n=3). The columns were used for more than 1 month without degradation. Liver extracts from arctic seal were analyzed.

[Methemoglobinemia--causes, diagnosis and treatment]. / Methemoglobinemi--årsaker, diagnostikk og behandling.

BACKGROUND: Methaemoglobinaemia is an infrequent condition. It can be congenital or be induced by several toxic compounds. In methaemoglobin (metHb) the iron in the haem moiety of haemoglobin is oxidized from the ferrous (Fe2+) to the ferric state (Fe3+). This complex is dark brown and unable to transport oxygen. Combined with a leftward shift in the oxyhaemoglobin dissociation curve this leads to decreased tissue oxygenation with subsequent hypoxic features in patients. CASE REPORTS: We report two cases of dapsone-induced methaemoglobinaemia. The blood, mucosa and nail beds adopted a brown-bluish appearance which was used diagnostically. One patient was treated effectively with repeated injections of methylene blue, which reduces methaemoglobin. In the other patient, the methaemoglobin level declined with a T50 of 50 hours. Both patients had few symptoms and made an uneventful recovery. INTERPRETATION: The hypoxia in methaemoglobinaemia may be effectively treated with methylene blue. Repeated injections may be necessary.

Determination of fenpyroximate in apples by supercritical fluid extraction and packed capillary liquid chromatography with UV detection.

A method using off-line supercritical fluid extraction (SFE) and micro liquid chromatography (microLC) with UV detection at 260 nm, was developed for selective determination of fenpyroximate in apple samples. The packed capillary liquid chromatography method utilises 20 microl injection volumes with on-column focusing. A 350x0.32 mm capillary column packed with Kromasil 100-C18 of 5 microm particle size was used with a mobile phase of acetonitrile-10 mM ammonium acetate (85:15, v/v) at a flow of 5 microl/min. A two-step SFE procedure was used to extract fenpyroximate selectively in 2 g apple samples, with Hydromatrix (HMX) added as a water absorbent at a 1:1 (w:w) ratio. Fenpyroximate was extracted at 200 bar and 90 degrees C for 15 min using carbon dioxide at a flow of 2 ml/min, and solvent trapping collection in 10 ml acetonitrile. The volume of the acetonitrile extract was reduced by evaporation and water was added to a final composition of acetonitrile-water (40:60, v/v). The resulting 2.0 ml solution was filtered using a 0.45 microm poly(vinylidene difluoride) syringe filter before microLC analysis. Validation of the method was accomplished with apple samples spiked with fenpyroximate, covering the range of 0.1 to 1.0 microg/kg. The within-day and between-day repeatabilities were in the range 4-18% relative standard deviation. Accuracy, measured as recovery, was found to be approximately 60%. Apple samples from a field treated with fenpyroximate were analysed. None of the samples contained fenpyroximate above the quantification level.

Temperature effects on packed-capillary liquid chromatography of the X-ray contrast agent iodixanol.

The effect of varying the operating temperature from 6 to 90 degrees C on the chromatographic performance of the exo-exo and exo-endo isomers of the X-ray contrast agent lodixanol in packed-capillary reversed-phase liquid chromatography shows increasing interconversion rates between the two isomeric conformers with increasing temperature. At 90 degrees C, Iodixanol elutes as one sharp peak due to an increased interconversion rate between the two isomeric conformers. Consequently, increased sensitivity is achieved. Temperature programming from 6 to 40 degrees C is utilized to optimize the resolution and determination of the exo-exo and exo-endo isomers. Temperature programming provides a significant decrease in the retention times in comparison with the isothermal separations while still preserving baseline separation of the isomers.

Hindered amine stabilizers investigated by the use of packed capillary temperature-programmed liquid chromatography. I. Poly((6-((1,1,3,3-tetramethylbutyl)-amino)-1,3,5-triazine-2,4- diyl)(2,2 ,6,6-tetramethyl-4-piperidyl)imino)-1,6-hexanediyl ((2,2,6,6-tetramethyl-4-piperidyl)imino)).

Three different trademarks of a hindered amine stabilizer with the IUPAC name poly((6-((1,1,3,3-tetramethylbutyl)-amino)-1,3,5-triazine-2,4-d iyl)(2,2,6,6-tetramethyl-4-piperidyl)imino)-1,6-hexanediyl(( 2,2 ,6,6-tetramethyl-4-piperidyl)imino)), have been analyzed and compared to each other by the use of non-aqueous packed capillary temperature-programmed liquid chromatography and light scattering detection. The analysis by this method has shown that the products contained almost 40 different homologues and other components. This is in contrast to what has been assumed earlier based on results achieved with size exclusion chromatography. The method demonstrated significant differences between the products from different manufacturers.

Purity testing of organometallic catalysts by packed capillary supercritical fluid chromatography.

A packed capillary column supercritical fluid chromatography system with flame ionization detection has been used for purity testing of candidates for homogeneous catalysis such as methyl tricarbonyl pentamethylcyclopentadienyl tungsten [Cp*W(CO)3Me], methyl tricarbonyl cyclopentadienyl tungsten [CpW(CO)3Me], tetramethyl pentamethylcyclopentadienyl iridium (Cp*IrMe4), trimethyl (1,4,7-trimethyl-1,4,7-triazocyclononane) rhodium (CnRhMe3), trimethylphosphine hydride dicarbonyl cyclopentadienyl molybdenum [eta5-CpMoH(CO)2PMe3] and triphenylphosphine hydride dicarbonyl cyclopentadienyl molybdenum [eta5-CpMoH(CO)2PPh3]. A mass limit of detection of 240 pg was found for eta5-CpMoH(CO)2PMe3 when using a 60-nl injection volume and pure CO2 as mobile phase on a 5 microm Kromasil C18 column. The stability of the catalysts in solution has been examined. After 24 h more than 70% of eta5-CpMoH(CO)2PMe3 and 50% of eta5-CpMoH(CO)2PPh3 had decomposed. Due to the instability of the compounds the purity testing had to take place rapidly after sample dissolution.

Hindered amine stabilizers investigated by the use of packed capillary temperature programmed liquid chromatography. II: Poly-(N-beta-hydroxyethyl-2,2,6,6-tetramethyl-4-hydroxypiperidyl succinate).

Three different trademark products of a hindered amine stabilizer with the IUPAC name poly-(N-beta-hydroxyethyl-2,2,6,6-tetramethyl-4-hydroxypiperidyl succinate), have been analyzed and compared to each other by the use of packed capillary temperature programmed liquid chromatography and light scattering detection. The analysis by this method has shown that the products contained approximately 50 different homologues and/or other components. The method also demonstrated its potential in purity control of products from different manufacturers.

Ultra trace detection of perfluorocarbon tracers in reservoir gases by adsorption/thermal desorption in combination with NICI-GC/MS.

A new method for the analysis of perfluorocarbon tracers (PFTs) in reservoir samples based on adsorption/thermal desorption in combination with NICI-GC/MS is presented. The tracer compounds were trapped in tubes filled with a carbon molecular sieve and in a two-step procedure thermally desorbed before they were analyzed with NICI-GC/MS. The chromatographic background noise, visible on GC/ECD-systems, due to compounds normally present in petroleum reservoir gases, could not be seen with NICI-GC/MS. Determination of the perfluorocarbons in reservoir gas samples confirmed the applicability of the method. Tracer concentrations as low as 42 femtoliter/liter were detected.

HPLC analysis of benzo[a]pyrene-albumin adducts in benzo[a]pyrene exposed rats. Detection of cis-tetrols arising from hydrolysis of adducts of anti- and syn-BPDE-III with proteins.

Quantitation of protein-benzo[a]pyrene adducts represent a more sensitive analysis method than quantitation of benzo[a]pyrene-DNA adducts. By accurate analysis of benzo[a]pyrene-protein adducts several different molecular adduct forms can be studied. Male Wistar rats were injected i.p. with benzo[a]pyrene, and serum albumin was isolated and subjected to acid hydrolysis at 90 degrees C for 3 h. The hydrolysate was analyzed by HPLC with fluorescence detection. The HPLC profiles obtained after albumin hydrolysis from benzo[a]pyrene exposed animals were compared to similar HPLC profiles from in vitro adducted bovine serum albumin (BSA) and direct hydrolysis of both r-10,t-9-dihydrodiol-c-7,8-oxy-7,8,9,10-tetrahydrobenzo[a]pyrene (syn-BPDE-III) and r-10,t-9-t-dihydrodiol-t-7,8-oxy-7,8,9,10-tetrahydrobenzo[a]pyrene (anti-BPDE-III). After acid hydrolysis of albumin from benzo[a]pyrene exposed rats, 6 fluorescent peaks were separated. Four of the peaks were isomers of benzo[a]pyrene-tetrahydrotetrols, (+/-)-benzo[a]pyrene-r-7,t-8,9,10-tetrahydrotetrol, (+/-)-benzo[a]pyrene-r-7,t-8,9,c-10-tetrahydrotetrol, (+/-)-benzo[a]pyrene-r-7,t-8,c-9,t-10-tetrahydrotetrol and (+/-)-benzo[a]pyrene-r-7,t-8,c-9,10-tetrahydrotetrol. In addition we found two fluorescent peaks, named X1 and X2 with retention times similar to the benzo[a]pyrene-tetrols. The unknown fluorescent peaks reacted similar to the four known tetrols in both dose response experiments and time course experiments. Fluorescent material with retention times equal to X1 and X2 were found after acid hydrolysis of syn-BPDE-III and anti-BPDE-III in acid and in hydrolysates from BSA treated in vitro with syn-BPDE-III and anti-BPDE-III. The ratio X1/X2 was relatively constant indicating epimerization equilibrium between these to species. Synchronous fluorescence analysis of fractions containing X1 or X2 from both in vivo and in vitro experiments showed fluorescence spectra characteristic of benzo[a]pyrene tetrols using a wavelength difference of 34 nm.

Nonaqueous electrochromatography on C30 columns: separation of retinyl esters.

A nonaqueous packed capillary electrochromatographic reversed-phase method for separation of retinyl esters has been developed. The retinyl esters all-trans-retinyl acetate, palmitate, heptadecanoate, stearate, oleoate, and linoleoate were separated on a 180 microm ID column packed with 5 microm C30 particles with a mobile phase consisting of 2.5 mM lithium acetate in N,N-dimethylformamide-methanol (99:1, v/v). With this mobile phase, the electroosmotic flow was 0.8 mm/s at 650 V/cm and 40 degrees C, and the separation was completed in less than 30 min on 30 cm columns. To obtain electrostable frits of the hydrophobic C30 material both the preparation of the frits and the conditioning of the column prior to electroconditioning were of importance. Selectivity changes were introduced by replacing up to 70% v/v of the N,N-dimethylformamide by acetonitrile. The increase in the amount of acetonitrile was, however, accompanied by a significant increase in analysis time. Liver extracts obtained from arctic seal were analyzed.

Capillary gas chromatography coupled with microplasma mass spectrometry for organotin speciation.

Gas chromatography was coupled with microplasma mass spectrometry for selective detection of organotin compounds. The microplasma ion source was a capacitively coupled radiofrequency helium plasma, which was located inside the high vacuum area of the mass spectrometer. Only 1-3 ml min-1 of helium carrier gas from the gas chromatograph was necessary for sustaining the plasma while 0.15-1.5 ml min-1 of hydrogen was added as reagent gas. Hydrogen was applied for prevention of carbon deposition and served to minimize the interactions between tin and the fused-silica inner surface of the microplasma ion source. Both carbon and tin were detected as positively charged atomic ions, which were expelled from the microplasma ion source and directly focused by electrostatic lenses towards the quadrupole mass analyzer. Tin exhibited high selectivity to carbon (> 10(4)) and a detection limit of 3.5 pg s-1.

Epimerization of benzo[a]pyrene-tetrols after acid hydrolysis, implications for determination of benzo[a]pyrene adducts in protein and DNA.

Determination of benzo[a]pyrene-DNA or protein adducts with high performance liquid chromatography (HPLC) after acid hydrolysis at high temperature (90 degrees C) enables four isomers of benzo[a]pyrene tetrahydrotetrol to be identified and quantitated. We have investigated the effect of acid treatment of benzo[a]pyrene-tetrahydrotetrol isomers using HPLC and nuclear magnetic resonance spectroscopy (NMR) analysis. By HPLC, we found reversible epimerization of (+/-)-benzo[a]pyrene-r-7,t-8,9, 10-tetrahydrotetrol to (+/-)-benzo[a]pyrene-r-7,t-8,9, c-10-tetrahydrotetrol and of (+/-)-benzo[a]pyrene-r-7,t-8,c-9, t-10-tetrahydrotetrol to (+/-)-benzo[a]pyrene-r-7,t-8,c-9, 10-tetrahydrotetrol, but no interconversion between the two isomer groups. After acid hydrolysis, we found an equilibrium of 87% (+/-)-benzo[a]pyrene-r-7,t-8,9,c-10-tetrahydrotetrol and 9% (+/-)-benzo[a]pyrene-r-7,t-8,9,10-tetrahydrotetrol and 68% (+/-)-benzo[a]pyrene-r-7,t-8,c-9,10-tetrahydrotetrol and 20% (+/-)-benzo[a]pyrene-r-7,t-8,c-9,t-10-tetrahydrotetrol. Minor amounts of two unknown compounds with similar chromatographic characteristics were also found. We have established a NMR method for determination of underivatized (+/-)-benzo[a]pyrene-r-7,t-8,9, c-10-tetrahydrotetrol and (+/-)-benzo[a]pyrene-r-7,t-8,9, 10-tetrahydrotetrol confirming the epimerization of (+/-)-benzo[a]pyrene-r-7,t-8,9,10-tetrahydrotetrol to (+/-)-benzo[a]pyrene-r-7,t-8,9,c-10- tetrahydrotetrol. (+/-)-Benzo[a]pyrene-r-7,t-8,9,10-tetrahydrotetrol was treated with aqueous hydrochloric acid in tetrahydro- furan-d8 to give (+/-)-benzo[a]pyrene-r-7,t-8,9,c-10-tetrahydrotetrol at 57 degrees C while observing the 1H NMR resonances at 500 MHz. Gradient-selected correlation spectroscopy (COSY), heteronuclear multiple quantum correlation (HMQC) and heteronuclear multiple bond correlation (HMBC) experiments were performed to confirm the assignments of the aliphatic hydrogens in the product (+/-)-benzo[a]pyrene-r-7,t-8,9, c-10-terahydrotetrol. Thus, when analyzing benzo[a]pyrene-DNA or protein adducts by cleaving the adducts with acid hydrolysis, the only ratio of biological significance is between (+/-)-benzo[a]pyrene-r-7,t-8,9,c-10-tetrahydrotetrol plus (+/-)-benzo[a]pyrene-r-7,t-8,9,10-tetrahydrotetrol and (+/-)-benzo[a]pyrene-r-7,t-8,c-9,10-tetrahydrotetrol plus (+/-)-benzo[a]pyrene-r-7,t-8,c-9,t-10-tetrahydrotetrol, due to interconversion (epimerization) at C-10.

Determination of low levels of an antioxidant in polyolefins by large-volume injection temperature-programmed packed capillary liquid chromatography.

Sub-ambient column temperatures, promoting strong interactions between the analyte and the stationary phase material, were utilized to focus large volumes of the polyolefin antioxidant Irganox 1076 [benzenepropanoic acid, 3.5-bis(1,1-dimethylethyl)-4-hydroxy-, octadecyl ester] on the column inlet, using pure acetonitrile as sample solvent and mobile phase. Injection volumes up to 100 microl were successfully employed on a 50 cm x 320 microm I.D. capillary column packed with 5 microm Kromasil 100 ODS particles. Irganox 1076 was eluted after completed injection by temperature programming, using a temperature program from 7 to 90 degrees C, in 3 degrees C min(-1). UV detection, using a low-dispersion "U"-shaped flowcell, was performed at 280 nm. The method was applied for the determination of Irganox 1076 that was extracted from low-density polyethylene (0.6 ppm, w/w). Both Soxhlet and microwave-aided solvent extractions were performed, using chloroform and acetonitrile as solvents, respectively. The microwave-aided extraction with acetonitrile was found to give approximately the same yield as the standard Soxhlet reference method. Consequently, small volumes of acetonitrile could be used both as extraction solvent, sample solvent and mobile phase, simplifying the analysis process. The mass limit of detection of the method was found to be 3.3 ng, corresponding to a concentration limit of detection of 33 ng ml(-1), utilizing an injection volume of 100 microl. The within and between day precision of retention times displayed relative standard deviations below 1.2%.

Microplasma mass spectrometric detection in capillary gas chromatography.

A simple and miniaturized 350-kHz helium discharge for plasma mass spectrometric detection in gas chromatography (GC) has been developed. The plasma was sustained at low pressure within the end of the capillary GC column (0.32-mm i.d.) inside the ion source housing of a quadrupole mass spectrometer. This allowed direct introduction of ions from the plasma to the mass analyzer using only a repeller and electrostatic lenses to focus the ions. The plasma was sustained in only 25 mL min(-)(1) of helium, which was accepted by the mass spectrometer vacuum system. This low gas flow also served to enhance the energy density of the discharge and to produce a narrow spray of ions toward the mass analyzer. Due to the miniaturized nature of the plasma, it was operated at a low power level (2.0 W), and traces of oxygen were added to avoid deposition of carbon. With this new concept for GC plasma mass spectrometric detection, chlorine was successfully monitored down to the 2.2 pg s(-)(1) level without interference from elements like C, S, P, O, F, and N.