Mechanism of Thermoelectric Performance Enhancement in CaMg2 Bi2 -Based Materials with Different Cation Site Doping.

Chemical bonds determine electron and phonon transport in solids. Tailoring chemical bonding in thermoelectric materials causes desirable or compromise thermoelectric transport properties. In this work, taking an example of CaMg2 Bi2 with covalent and ionic bonds, density functional theory calculations uncover that element Zn, respectively, replacing Ca and Mg sites cause the weakness of ionic and covalent bonding. Electrically, Zn doping at both Ca and Mg sites increases carrier concentration, while the former leads to higher carrier concentration than that of the latter because of its lower vacancy formation energy. Both doping types increase density-of-state effective mass but their mechanisms are different. The Zn doping Ca site induces resonance level in valence band and Zn doping Mg site promotes orbital alignment. Thermally, point defect and the change of phonon dispersion introduced by doping result in pronounced reduction of lattice thermal conductivity. Finally, combining with the further increase of carrier concentration caused by Na doping and the modulation of band structure and the decrease of lattice thermal conductivity caused by Ba doping, a high figure-of-merit ZT of 1.1 at 823 K in Zn doping Ca sample is realized, which is competitive in 1-2-2 Zintl phase thermoelectric systems.

Breaking the Minimum Limit of Thermal Conductivity of Mg3 Sb2 Thermoelectric Mediated by Chemical Alloying Induced Lattice Instability.

Thermal properties strongly affect the applications of functional materials, such as thermal management, thermal barrier coatings, and thermoelectrics. Thermoelectric (TE) materials must have a low lattice thermal conductivity to maintain a temperature gradient to generate the voltage. Traditional strategies for minimizing the lattice thermal conductivity mainly rely on introduced multiscale defects to suppress the propagation of phonons. Here, the origin of the anomalously low lattice thermal conductivity is uncovered in Cd-alloyed Mg3 Sb2 Zintl compounds through complementary bonding analysis. First, the weakened chemical bonds and the lattice instability induced by the antibonding states of 5p-4d levels between Sb and Cd triggered giant anharmonicity and consequently increased the phonon scattering. Moreover, the bond heterogeneity also augmented Umklapp phonon scatterings. Second, the weakened bonds and heavy element alloying softened the phonon mode and significantly decreased the group velocity. Thus, an ultralow lattice thermal conductivity of ≈0.33 W m-1 K-1 at 773 K is obtained, which is even lower than the predicated minimum value. Eventually, Na0.01 Mg1.7 Cd1.25 Sb2 displays a high ZT of ≈0.76 at 773 K, competitive with most of the reported values. Based on the complementary bonding analysis, the work provides new means to control thermal transport properties through balancing the lattice stability and instability.

Design of N-Type Textured Bi2 Te3 with Robust Mechanical Properties for Thermoelectric Micro-Refrigeration Application.

Thermoelectric refrigeration is one of the mature techniques used for cooling applications, with the great advantage of miniaturization over traditional compression refrigeration. Due to the anisotropic thermoelectric properties of n-type bismuth telluride (Bi2 Te3 ) alloys, these two common methods, including the liquid phase hot deformation (LPHD) and traditional hot forging (HF) methods, are of considerable importance for texture engineering to enhance performance. However, their effects on thermoelectric and mechanical properties are still controversial and not clear yet. Moreover, there has been little documentation of mechanical properties related to micro-refrigeration applications. In this work, the above-mentioned methods are separately employed to control the macroscopic grain orientation for bulk n-type Bi2 Te3 samples. The HF method enabled the stabilization of both composition and carrier concentration, therefore yielding a higher quality factor to compare with that of LPHD samples, supported by DFT calculations. In addition to superior thermoelectric performance, the HF sample also exhibited robust mechanical properties due to the presence of nano-scale distortion and dense dislocation, which is the prerequisite for realizing ultra-precision machining. This work helps to pave the way for the utilization of n-type Bi2 Te3 for commercial micro-refrigeration applications.

Mediating Point Defects Endows n-Type Bi2 Te3 with High Thermoelectric Performance and Superior Mechanical Robustness for Power Generation Application.

Bi2 Te3 -related alloys dominate the commercial thermoelectric market, but the layered crystal structure leads to the dissociation and intrinsic brittle fracture, especially for single crystals that may worsen the practical efficiency. In this work, point defect configuration by S/Te/I defects engineering is engaged to boost thermoelectric and mechanical properties of n-type Bi2 Te3 alloy, which, coupled with p-type BiSbTe, shows a competitive conversion efficiency for the fabricated module. First, as S alloying suppresses the intrinsic B i T e , antisite defects and forms a donor-like effect, electronic transport properties are optimized, associated with the decreased thermal conductivity due to the point defect scattering. The periodide compound TeI4 is afterward adopted to further tune carrier concentration for the realization of an optimal ZT. Finally, an advanced average ZT of 1.05 with ultra-high compressive strength of 230 MPa is achieved for Bi2 Te2.9 S0.1 (TeI4 )0.0012 . Based on this optimum composition, a fabricated 17-pair module demonstrates a maximum conversion efficiency of 5.37% under the temperature difference of 250 K, rivaling the current state-of-the-art Bi2 Te3 modules. This work reveals the novel mechanism of point defect reconfiguration in synergistic enhancement of thermoelectric and mechanical properties for durably commercial application, which may be applicable to other thermoelectric systems.

Achieving High Thermoelectric Performance in Rare-Earth Element-Free CaMg2Bi2 with High Carrier Mobility and Ultralow Lattice Thermal Conductivity.

CaMg2Bi2-based compounds, a kind of the representative compounds of Zintl phases, have uniquely inherent layered structure and hence are considered to be potential thermoelectric materials. Generally, alloying is a traditional and effective way to reduce the lattice thermal conductivity through the mass and strain field fluctuation between host and guest atoms. The cation sites have very few contributions to the band structure around the fermi level; thus, cation substitution may have negligible influence on the electric transport properties. What is more, widespread application of thermoelectric materials not only desires high ZT value but also calls for low-cost and environmentally benign constituent elements. Here, Ba substitution on cation site achieves a sharp reduction in lattice thermal conductivity through enhanced point defects scattering without the obvious sacrifice of high carrier mobility, and thus improves thermoelectric properties. Then, by combining further enhanced phonon scattering caused by isoelectronic substitution of Zn on the Mg site, an extraordinarily low lattice thermal conductivity of 0.51 W m-1 K-1 at 873 K is achieved in (Ca0.75Ba0.25)0.995Na0.005Mg1.95Zn0.05Bi1.98 alloy, approaching the amorphous limit. Such maintenance of high mobility and realization of ultralow lattice thermal conductivity synergistically result in broadly improvement of the quality factor ß. Finally, a maximum ZT of 1.25 at 873 K and the corresponding ZT ave up to 0.85 from 300 K to 873 K have been obtained for the same composition, meanwhile possessing temperature independent compatibility factor. To our knowledge, the current ZT ave exceeds all the reported values in AMg2Bi2-based compounds so far. Furthermore, the low-cost and environment-friendly characteristic plus excellent thermoelectric performance also make the present Zintl phase CaMg2Bi2 more competitive in practical application.

Enhanced Thermoelectric Properties of p-Type CaMg2Bi2 via a Synergistic Effect Originated from Zn and Alkali-Metal Co-doping.

Bi-based Zintl phase CaMg2Bi2 is a promising thermoelectric material. Here, we report that the high-concentration point defects induced by equivalent Zn doping on the Mg site significantly enhance phonon scattering and then suppress lattice thermal conductivity by 50% at room temperature. Subsequently, partial substitution of divalent calcium ions with alkali-ion doping (Li, Na, K) not only optimizes the electrical transport properties by increasing the carrier concentration but also further reduces the lattice thermal conductivity through crystal disorder. Finally, the synergistic effect of Zn and Li co-doping leads to a high ZT of ∼1.0 at 873 K and an average ZT of 0.6 between 300 and 873 K for Ca0.995Li0.005Mg1.9Zn0.1Bi1.98. This work demonstrates an instructive method to reduce the lattice thermal conductivity via doping at the Mg site, which has never been reported in the CaMg2Bi2 system. Moreover, high-performance Ca0.995Li0.005Mg1.9Zn0.1Bi1.98 alloy does not contain any toxic elements and expensive rare earth elements, which is of great significance for the development of environment-friendly thermoelectric materials.