RESUMEN
Deep water and shallow layers mostly feature weakly cemented formations, with complex geological structures, geological looseness, susceptibility to collapse. In order to obtain information on weakly cemented formation materials, weakly cemented argillaceous siltstone is simulated as the research object and the focus is on analysing the influence of ultrasonic frequency, density, particle size (porosity), and compressive strength on P-wave velocity and establishing the correlation relationship between longitudinal wave velocity and each parameter through indoor simulation experiments. The results showed that there is a linear relationship between P-wave velocity and ultrasonic frequency in terms of positive correlation as well as compressive strength. The nonlinear relationship between P-wave velocity and particle size (porosity) is a negative correlation, while the nonlinear relationship between sound velocity and density is a positive correlation. In addition, the influence of core height on P-wave velocity is analysed; it is found that as the core height increases, the velocity slightly decreases, and each ultrasonic frequency has an ultimate height for sound wave penetration. Through the response relationship between ultrasound and the physical properties of weakly cemented formations, indirect acquisition can be achieved, which is of great significance for the development of oil and gas in weakly cemented formations.
RESUMEN
Microcracks in the annular cement sheath of oil wells frequently cause annular water channeling. Traditional cement squeeze technology has a low success rate in controlling this issue. Based on the conventional profile control water-blocking agent for underground in situ gelling and polyacrylic acid, a pH intelligent response microcrack-blocking agent was developed to block the microcrack in the cement sheath. The study investigated the influence of pH on the viscosity characteristics of the new blocking agent, the impact of polyacrylic acid on the compression recovery ability of the new blocking agent after gelling, the change in viscosity of the blocking fluid after flowing through the microcrack in the cement sheath, and the blocking effect after gelling. The results indicated that the new blocking agent has excellent viscosity-increasing ability with pH. After flowing through the microcrack in the cement sheath, the viscosity of the blocking agent increased significantly with the extension of the contact distance between the blocking agent and the microcrack in the cement sheath, which is very conducive to the retention of the blocking agent in the microcrack of the cement sheath. Polyacrylic acid had a negligible effect on the compression recovery ability of the blocking agent after gelling. At a fracture length of 5 cm, the pressure-bearing capacity of the blocking agent could reach 6 MPa.
RESUMEN
The latex used conventionally for oil-well cementing can lead to serious foaming issues in the cement slurry, which not only affects the accurate measurement of the density of the latex-containing cement slurry, but also is detrimental to cementing construction. A large amount of a foam stabilizer used for latex preparation is mainly responsible for foaming of the latex-containing cement slurry. In this study, soap-free emulsion polymerization was conducted using 2-acrylamido-2-methylpropanesulfonic acid (AMPS), styrene (St), and butyl acrylate (BA) as the reaction monomers and the effects of the AMPS dosage, monomer ratio, reaction temperature and stirring speed on the performance of the latex were investigated. The optimum synthesis conditions included a 30% monomer concentration, an St : BA : AMPS monomer ratio of 5 : 4 : 6, a synthesis temperature of 85°C, a stirring speed of 400 r.p.m. and 1.5% of the initiator. As-prepared latex exhibited good filtration loss control, excellent freeze-thaw stability, and extremely low foaming of the cement slurry with the added latex, which was extremely beneficial for on-site cementing construction.
RESUMEN
During the process of well cementing in deep water, the cement slurry experiences a wide range of temperature variation from low temperature at seabed to high temperature in downhole. The elevated temperature affects the rheology of cement slurry. The change of rheology of cement slurry could influence the safety of cementing operation. The aim of this paper is to develop a new kind of hydrophobically associating water-soluble polymer (NHAWP) as an additive to prepare a constant rheology oil well cement slurry, which can be used at temperature range from 4°C to 90°C. The acrylamide, 2-acrylamide-2-methylpropionic acid and stearyl methylacrylate were applied to synthesize the NHAWP by the inverse microemulsion polymerization. Test results indicate that the critical association temperature of NHAWP is 45°C. The critical association temperature is independent of NHAWP concentration, salt concentration and alkalinity of solution. When the temperature is below 45°C, NHAWP shows little influence on the viscosity of solution. When the temperature is above 45°C, the NHAWP forms spatial network structure by intermolecular hydrophobic association and thus increases the viscosity of solution significantly. The NHAWP also displays good thermal stability and excellent salt and alkali resistance properties. In addition, the NHAWP shows nearly no negative influence on the basic properties of cement slurry, which indicates that the NHAWP can be used as a constant rheology agent to prepare a cement slurry with constant rheology in the temperature range of 4°C to 90°C.
RESUMEN
This research work designed a novel mud-cake solidification method to improve the zonal isolation of oil and gas wells. The calculation methodology of mud-cake compressive strength was proposed. The optimal formula of activator and solid precursors, the proper activating time and the best activator concentration were determined by the compressive strength test. The effects of solid precursors on the properties of drilling fluid were evaluated. Test results show that the respective percentage of bentonite, metakaolin, slag and activator is 1 : 1 : 0.3 : 0.8, as well as the optimum ratio of Na2SiO3/NaOH is 40 : 1. The optimum concentration of activator is 0.21 and the activating time should be more than 10 min. The solid precursors did not show any bad influence on the rheological property of drilling fluids. Even though the compressive strength decreased when the solid precursors blended with barite, the strength values can still achieve 8 MPa. The reaction of metakaolin and activator formed cross-link structure in the mud-cake matrix, which enhanced the connection of the loose bentonite particles, lead to the significant enhancement of shear bonding strength and hydraulic bonding strength. This mud-cake solidification method provides a new approach to improve the quality of zonal isolation.
RESUMEN
A significant amount of research has been conducted on bentonite-acrylamide hydrogels. These gels are usually prepared by uniformly mixing bentonite with reactive monomers. Herein, a new preparation method of bentonite-acrylamide hydrogels has been proposed to cater to one novel application of bentonite-acrylamide hydrogels. In this method, bentonite-acrylamide hydrogel was obtained by pressing bentonite into a thin mud cake and extruding a mixed liquor of acrylamide, a cross-linking agent, an initiator, and water into the thin mud cake and then subjecting the system to water-bath curing. The effects of extrusion pressure, extrusion time, and acrylamide concentration on the tensile strength and elemental composition of bentonite-acrylamide hydrogel were investigated. The results show that the tensile strength of the bentonite-acrylamide hydrogel first increased and then tended to be stable with the further increase in extrusion pressure and extrusion time. As the concentration of acrylamide increased, the tensile strength of the bentonite-acrylamide hydrogel increased first and then decreased slightly. With the increase in extrusion pressure, extrusion time, and acrylamide concentration, the contents of C and N elements in the thin mud cake gradually increased and then tended to be stable, which reflects the state of the monomer entering the thin mud cake. In addition, the elemental composition of the bentonite-acrylamide hydrogel was analyzed via the scanning electron microscopy-energy dispersive X-ray spectrometry method, and it was found that the composition of the hydrogel was relatively uniform in the direction of mixed liquor extrusion.
RESUMEN
The retarding side effect and the compatibility with other additives are the main problems that limit the field application of the synthesized fluid loss control additive (FLCA). The effect of the type and content of carboxylic acid groups on the retarding side effect of FLCA and the compatibility between FLCA and the retarder AMPS-IA synthesized using 2-acrylamido-2-methyl propane sulfonic acid (AMPS) and itaconic acid (IA) was studied in this paper. The type and content of carboxylic acid group have a great influence on the fluid loss control ability, the compatibility with retarder and the retarding side effect of FLCA. FLCA containing IA or maleic acid (MA) shows better compatibility with retarder than FLCA containing acrylic acid, but the retarding side effect of FLCA containing MA is weaker than that of FLCA containing IA. Thus, MA is the most suitable monomer for synthesizing FLCA having good compatibility with retarder AMPS-IA.
